高精度物镜波纹管致动器的线性度分析

采用有限元方法对高精度物镜波纹管致动器的几何非线性变形进行了分析,并引入线性度对波纹管致动器的性能进行了评估.通过有限元方法分析了常见的U型、S型、C型、方型及三角型波纹管的几何非线性变形,并结合最小二乘法,得到了上述各种波纹管致动器的行程及线性度.计算结果表明：在设计大行程波纹管致动器时,S型波纹管的线性度最好,为0.161%|而在设计小行程波纹管致动器时,三角形波纹管的线性度最好,为0.135%.     

超薄镜的有限元分析

建立了组成空间望远镜主镜的超薄扇形子镜的有限元模型,分析了镜面的热变形和影响函数。通过对热变形的分析表明,为了减小空间温度场产生的镜面变形,应该选用具有一定弹性的面形致动器,或者致动器与镜面之间具有一定的相对滑动能力。通过对影响函数的分析表明:对所研究的弹性致动器来说,相邻致动器器之间具有明显的位移耦合,间隔致动器的耦合可以忽略;边缘致动器由于受到的约束比较小,在同样的致动伸长量下,产生的位移大于中心致动器。     

基于迟滞非线性补偿系统的光学元件形貌检测

为了减少相移干涉仪中压电陶瓷致动器进行相移时,其迟滞非线性对相移算法中的相位计算带来的误差,设计了一套压电陶瓷致动器的控制系统.利用高精度电阻应变传感器和基于锁相放大原理的信号调理电路检测压电陶瓷致动器位移,建立多项式数学模型描述迟滞非线性,然后提出了一种前馈开环控制方法补偿其迟滞非线性.最后,基于所提出的方案对压电陶瓷致动器进行了期望轨迹的跟踪控制实验,同时将补偿控制系统与干涉仪相结合检测光学元件表面形貌.实验结果表明:补偿后,压电陶瓷致动器的跟踪误差在-0.156μm与+0.078μm之间,迟滞非线性度由10.4%降到2.4%,且干涉仪所测得的光学元件表面面形起伏高度均方根和峰谷分别改变了0.795nm和3.937nm.该系统对于高精度的光学元件形貌检测具有重要的意义.     

变宽度分割电极片状压电致动器的位移特性

针对硬磁盘驱动器中磁头定位两级伺服系统设计了一种新型压电致动器——悬臂梁式变宽度分割电极片状压电致动器.沿厚度方向极化的PZT压电陶瓷薄长片，宽度沿长度方向变化且沿长轴对称，一端固定一端自由构成悬臂梁.其上下两表面的电极均沿长轴分割成对称的两部分.施加电场使其中一半在d₃₁模式作用下伸长，而与其对称的另一半缩短，则压电片沿宽度方向产生弯曲，自由端便可产生致动位移.对该致动器的驱动电压-端部致动位移特性进行了理论分析、有限元模拟及实验验证.致动器中的电场诱导应力远小于陶瓷的抗张强度.致动器端部位移的测试结果略大于理论计算值.与现有磁头悬浮臂尺寸相近的致动器，在20—50V的电压驱动下均可获得1—2μm的致动位移.对25kTPI(track per inch)的高道密度硬磁盘，该位移已能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器致动位移的基本要求. 关键词：     

低温风洞电动推杆热防护结构非线性屈曲分析

为避免电动推杆元件在低温风洞中工作时受到低温损伤而无法正常工作,设计了使其能够在低温环境下正常工作的热防护结构。基于ANSYS软件建立了热防护结构有限元模型并进行线性屈曲分析,得到了相应屈曲模态。考虑材料非线性,以线性屈曲模态作为结构初始几何缺陷形式,使用Newton-Raphson算法控制载荷加载对热防护结构进行了非线性屈曲分析。结果表明:一阶线性屈曲临界压力为1.651MPa,以其变形量的0.1倍作为初始几何缺陷得到非线性屈曲临界压力为1.544MPa,考虑安全系数(m=3)后许用外压为0.515MPa,高于低温风洞最大工作压力0.35MPa。热防护结构非线性屈曲临界压力随初始几何缺陷的增加而降低,当初始几何缺陷大于一阶线性屈曲模态变形量的约1.4倍时,许用外压低于0.35MPa,结构有可能发生失稳。不同初始几何缺陷形式对热防护结构的临界压力几乎无影响,但结构最终破坏形式不同。     

梳状型高线性度一维位敏检测器

介绍了一种梳状型一维位敏检测器(PSD)的结构,对其工作原理进行了分析.比较测试了这种梳状结构(1mm×12mm)PSD与普通块状型结构(1mm×3mm)PSD的线性度,实验表明:梳状结构的PSD具有极高的线性度(均方根非线性为0.17%F.S)和较小的边缘失真.对影响一维PSD线性度的因素进行了分析,并对结果进行了讨论.     

不锈钢波纹管检测换能器的设计与应用研究

研制了一种用于不锈钢波纹管检测的磁致伸缩换能器。首先选用多物理场耦合分析软件对圆管的磁场分布规律进行有限元仿真,证实增加铁磁性条带后,磁场强度显著提高。而后通过均匀包裹一层镍合金薄带的方式,改进了磁致伸缩换能器的结构,并成功识别出环向裂纹缺陷。同时分析了试验过程中不确定度的来源,推导出了仅含有直接测量值的标准不确定度合成公式。研究结果为采用磁致伸缩换能器进行不锈钢波纹管缺陷无损评价提供了理论依据。      

可调波长半导体激光法布里-珀罗干涉仪

为了对激光十涉仪、高精度位移传感器等测量系统进行纳米级精度的非线性误差校准,需进一步提高中国计量科学研究院与清华大学合作研制的差拍F-P 干涉仪的线性度、稳定性及测量范围.在合理分析空气折射率变化及He-Ne激光器纵模调谐范围等因素对测量的影响基础上,设计并制作了密封干涉光路的真宅系统,并用调谐范围较大的半导体激光器作为工作激光器.实验结果表明,系统在大于1/4波长的行程范围内的线性度有明显的提高,最大非线性误差由8.93 nm减小至1.19 nm.     

基于接触非线性分析方法的反射镜组件工程分析

工程中将实际的非线性系统近似为线性系统,用线性分析方法对所研究的对象进行分析往往会带来较大的求解误差。介绍了产生结构非线性的主要因素,并在接触理论基础上,对某空间相机反射镜组件进行了合理的有限元建模。采用接触非线性分析方法对螺钉预紧时反射镜的响应及在自重和温度载荷作用下反射镜的变形进行了分析。通过比较线性分析与非线性分析的结果表明:采用非线性分析的结果更接近实际;在空间相机的工程分析中,对某些接触部位采用非线性的分析方法可以提高分析精度。     

真空波荡器楔口机构结构分析与优化

 为了满足物理设计要求,楔口机构被应用于真空波荡器机械系统设计中。利用有限元分析软件ANSYS Workbench对上海光源真空波荡器的关键部件——楔口机构进行了线性静态分析,得到了该关键部件的变形和应力分布情况及它们对外大梁变形和滚动角的影响,采用补偿弹簧系统并进行参数优化减小了影响,使之满足工作中的高精度需要。分析结果在真空波荡器调试过程中得到了验证,与实际情况基本吻合。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.