pH- and Ionic-Strength-Induced Structural Changes in Poly(acrylic acid)-Lipid-Based Self-Assembled Materials

Summary: The effect of a polyanion introduced as a lipid conjugate (poly(acrylic acid)- dimyristoyl-sn-glycero-3-phosphoethanolamine, PAA-DMPE) on the structure of a self-assembled, biomembrane mimetic has been evaluated using synchrotron small-angle X-ray scattering (SAXS). At high grafting density (8–11 mol.%), the PAA chains were found to produce significant changes in structure in response to changes in pH and electrolyte composition. At low pH and in the absence of salt (NaCl), the neutral PAA chains adopt a coil conformational state that leads to the formation of a swollen lamellar structure. Upon the addition of salt at low to intermediate pH values, two lamellar phases, a collapsed and an expanded structure, coexist. Finally, when the polymer is fully ionized (at high pH), the extended conformation of the polymer generates a cubic phase. The results of this study contribute to an understanding of how polyelectrolytes may ultimately be harnessed for the preparation of self-assembling materials responsive to external stimuli.     

Hollow capsules formed in a single stage via interfacial hydrogen-bonded complexation of methylcellulose with poly(acrylic acid) and tannic acid

Hollow capsules can be prepared in a single stage by the interfacial complexation of methylcellulose (MC) with poly(acrylic acid) (PAA) or tannic acid (TA) via hydrogen bonding in aqueous solutions. The formation of capsules is observed when viscous solution of methylcellulose is added drop-wise to diluted solutions of polyacids under acidic conditions. The optimal parameters such as polymer concentration and solution pH for the formation of these capsules were established in this work. It was found that tannic acid forms capsules in a broader range of concentrations and pHs compared to poly(acrylic acid). The TA/MC capsules exhibited better stability compared to PAA/MC in response to increase in pH: the dissolution of TA/MC capsules observed at pH > 9.5; whereas PAA/MC capsules dissolved at pH > 3.8. The interfacial complexation can be considered as a potential single stage alternative to the formation of capsules using multistage layer-by-layer deposition method.     

Effect of Membrane Potential on the Binding of Merocyanine 540 to Human Erythrocytes

Illumination of erythrocytes in the presence of merocyanine 540 (MC540) resulted in changed binding characteristics of MC540, i.e. a red shift in the emission maximum of bound dye with an increase in the relative fluorescence quantum yield. Aluminum phthalocyanine tetrasulfonate-mediated photodynamic treatment, before addition of MC540, resulted in a comparable change in the MC540-binding characteristics with, in addition, an increase in the concentration of MC540 in the membrane. Both photodynamic treatments induce depolarization of the red cell membrane, with a dose dependency comparable to that of changed MC540 binding. Also depolarization, induced by incubation of the cells with A23187 in the presence of Ca₂+ in high [K+] buffer, resulted in similar changes in the MC540 binding characteristics. These results indicate a relation between photodynamically induced membrane depolarization and changed MC540-binding characteristics. Hyperpolarization induced by incubation with A23187 in low [K+] buffer resulted in decreased binding of MC540. In accordance, the MC540-mediated photodamage to red cells decreased upon hyperpolarization of the cells. The results indicate that the binding of MC540 to erythrocytes is strongly dependent on the membrane potential and that hyperpolarization of the membrane could be a possible protection mechanism for erythrocytes against MC540-mediated photodynamic damage.     

Hydrogen‐Bonded Complexes and Blends of Poly(acrylic acid) and Methylcellulose: Nanoparticles and Mucoadhesive Films for Ocular Delivery of Riboflavin

Poly(acrylic acid) (PAA) and methylcellulose (MC) are able to form hydrogen‐bonded interpolymer complexes (IPCs) in aqueous solutions. In this study, the complexation between PAA and MC is explored in dilute aqueous solutions under acidic conditions. The formation of stable nanoparticles is established, whose size and colloidal stability are greatly dependent on solution pH and polymers ratio in the mixture. Poly(acrylic acid) and methylcellulose are also used to prepare polymeric films by casting from aqueous solutions. It is established that uniform films can be prepared by casting from polymer mixture solutions at pH 3.4–4.5. At lower pHs (pH < 3.0) the films have inhomogeneous morphology resulting from strong interpolymer complexation and precipitation of polycomplexes, whereas at higher pHs (pH 8.3) the polymers form fully immiscible blends because of the lack of interpolymer hydrogen‐bonding. The PAA/MC films cast at pH 4 are shown to be non‐irritant to mucosal surfaces. These films provide a platform for ocular formulation of riboflavin, a drug used for corneal cross‐linking in the treatment of keratoconus. An in vitro release of riboflavin as well as an in vivo retention of the films on corneal surfaces can be controlled by adjusting PAA/MC ratio in the formulations.     

Polyelectrolyte effects on the quenching of pyrene fluorescence in solutions of a pyrene substituted poly(acrylic acid)

The quenching of pyrene fluorescence by nitromethane, Tl⁺, Cu²⁺, I^?, and 4-dimethylaminopyridine (DMAP) in aqueous solutions of a pyrene substituted poly(acrylic acid) ( 1 ) was influenced by the “polyelectrolyte effect” of 1 . The efficiency of quenching in solutions of 1 was measured in terms of the Stern–Volmer constants for dynamic and static quenching which were obtained from comparison of the intensity and lifetime of pyrene fluorescence in solutions of 1 and a monomer model compound. The efficiency of quenching in solutions of 1 was always greater at high pH ( 9 ) in comparison to that at low pH ( 4 ). The ionization of carboxylic groups in 1 caused an expansion of the polymer mainchain and concomitant exposure of the pyrene molecules to the aqueous phase and quencher. The polyanion domain of 1 favored the condensation of cationic quenchers and could account for very efficient quenching in case of Cu²⁺ and Tl⁺. A very efficient quenching of pyrene fluorescence in solutions of 1 by DMAP at high pH was attributed to the hydrophobic interactions of DMAP and pyrene moiety. The iodide ions were less efficient quenchers of pyrene fluorescence due to electrostatic repulsion from the polyanion. The efficiency of quenching by nitromethane was not significantly affected by ionization of the carboxylic groups in 1 .     

Probing the pH-dependent chain dynamics of poly(acrylate acid) in concentrated solution by using a cationic AIE fluorophore

We report a novel strategy to study the chain dynamics of poly(acrylic acid) (PAA) in a relative concentrated solution (1.0 g/L). The strategy is based on the fluorescent probe (DCTPE) with unique aggregation-induced emission (AIE) characteristics. Free DCTPE molecules are non-emissive in aqueous solution, but they become highly emissive when trapped in polymer coils. The fluorescence intensity is proportional to the efficiency of trapping DCTPE molecules in polymer coils. By correlation the change of fluorescence intensity with the variation of pH value (from 1.78 to 12.06), the PAA chain’s dynamics in the relatively concentrated solution have been elucidated into three processes. In the pH range from 12.06 to 6.0, PAA chains take an extended and non-folding conformation. Changing pH from 6.0 to 3.86, PAA chains are partially protonated and loosely packed polymer coils are formed. Further lowering the pH value of the solution (from 3.86 to 1.78), protonated segments dominate the PAA chains, and at the same time, the intermolecular hydrogen bonding takes effect, thus the polymer chains posses in the conformation of more compact coils.     

Size and pH effect on electrical and conformational behavior of poly(acrylic acid): Simulation and experiment

Monte Carlo simulations, experimental titrations and fluorescence correlation spectroscopy experiments were used to investigate the conformational and electrical properties of polyacrylic acids (PAA). On the one hand, titration curves were calculated to get an insight into the role of pH on the degree of ionization and conformation of PAA chains. On the other hand, experimental potentiometric titrations of PAA were also achieved for different PAA molecular weights and compared to the calculated titration curves obtained by Monte Carlo coarse grained simulations. It was found that for a large range at intermediate PAA ionizations, a good correlation is obtained between experimental and simulations data thanks to the prominence of electrostatic interactions in this domain. The effect of ionic concentration and PAA molecular weight on the titration curves was also investigated. In order to get a better understanding of PAA conformational behavior, we also investigated PAA diffusion properties in aqueous solutions as a function of pH and ionic strength by fluorescence correlation spectroscopy (FCS), thanks to its high sensitivity to measure diffusion coefficients of tracer solutes. Good qualitative agreements were observed between experimental diffusivities and polymer properties calculated from MC simulations. It was shown that the high molecular weight PAA chains display more significant changes in diffusivity in agreement with the ionization degrees and conformational changes observed in the simulations.     

Pyrene Fluorescence in the Presence of Acrylic Acid-Ethyl Methacrylate Copolymers: Effect of the Copolymer Composition in the Formation of Microdomains*

The properties of aqueous solutions of acrylic acid-ethyl methacrylate (EMA) copolymers have been investigated using pyrene and pyrene pyrenebutyltrimethylammonium (PBTA) as probes. Static and dynamic fluorescence have been used to obtain information about the microenviron-ments formed. Micropolarity studies using the I₁/I₃ ratio of the vibronic bands of pyrene show the formation of hydrophobic domains. At low pH the increase of the amount of ethyl methacrylate in the copolymers shows that aqueous microdomains are excluded from the core of the polymer, for the copolymers with high content of EMA low polarity microdomains are still present on the mac-romolecular chain even at higher pH. The pH-induced conformational transition indicates that the more hydro-phobic copolymers adopt a more tightly coiled conformation. Compared to PAA, the decay times for both probes are increased twice for the polymer with 25% molar proportion of EMA. The fluorescence quenching of the probes by nitromethane depends on pH, copolymer composition and probe structure. The efficiency of quenching decreases with increase of the EMA proportion in the copolymers. Pyrene is more efficiently quenched than PBTA as a consequence of the latter being located in more internal (less accessible) sites of the polymer structure.     

pH,serum proteins and ionic strength influence the uptake of merocyanine 540 by WiDr cells and its interaction with membrane structures

It has been suggested that selective uptake of photosensitizers is due to significantly lower pH of the interstitial fluid in tumors compared to normal tissue. Therefore, the cellular uptake of merocyanine 540 (MC 540) was examined at two pH values: 6.8+/-0.1 and 7.4+/-0.1. There was no difference in spectral properties (absorption and fluorescence maxima positions, fluorescence intensity) of the drug in the presence of increasing amounts of either human blood plasma or FCS (0-2%) at the two pH values investigated. Nevertheless, significantly higher amounts of the drug were taken up by WiDr cells at pH 6.8+/-0.1, both in the presence of 10% FCS and in the absence of FCS. The absorption spectra of MC 540 in the presence of egg phosphatidylcholine (PC) liposomes turned out to be NaCl concentration-dependent (0.00-0.30 mol l(-1)). Membrane fluidity, as measured by fluorescence anisotropy of diphenylhexatriene (DPH), was unchanged within the experimental error in the NaCl concentration range 0.01-0.30 mol l(-1). The spectral changes indicated an enhancement of the incorporation of MC 540 into lipid membranes with increasing ionic strength. Such a salt concentration dependence suggests a possible involvement of the surface potential in the interaction of MC 540 with lipid membranes. The results might provide an explanation of the pH dependency of the cellular uptake of MC 540 observed in this study.     

Molecular dynamics simulation on the interaction between polymer inhibitors and anhydrite surface

Investigation on the microscopic interaction between polymer inhibitors and calcium sulfate will be helpful for understanding its scale inhibition mechanism and can provide a theoretical guidance to developing new scale inhibitors. In this work, molecular dynamics simulations with COMPASS force field have been performed to simulate the interaction between hydrolyzed polymaleic anhydride (HPMA), polyaspartic acid (PASP), polyepoxysuccinic acid (PESA), polyacrylic acid (PAA) and the (001) and (020) surfaces of anhydrite (AD) crystal with and without water. The results show that the sequence of binding energies between four polymer inhibitors and AD (001) and (020) with water is PESA > PASP > HPMA > PAA. The binding energy of the same polymer inhibitor on AD (001) is smaller than that on AD (020). Water molecules weaken the deformations of HPMA and PAA but aggravate those of PASP and PESA. Natural bond orbital (NBO) charges of the repeat units of polymer inhibitors were calculated by B3LYP/6‐31G* method. The Coulomb interaction is formed between the O atoms of polymer inhibitors and the Ca atoms of AD crystal. The system of polymer–AD is mainly contributed from the non‐bonding interaction. Polymer inhibitors do not interact directly with AD crystal, but indirectly through the interactions between inhibitor–H₂O and H₂O–AD, i.e. water molecules participate in scale inhibition of polymer inhibitors to AD crystal. Water molecules cannot be ignored when the interaction models are constructed, i.e. solvent effect cannot be ignored. Copyright © 2015 John Wiley & Sons, Ltd.     

Complex macromolecular dynamics:: I. Estimation technique for time-resolved emission anisotropy ratio of chromophores incorporated into polymer chains

Time-resolved fluorescence emission anisotropy ratios of carbazolyl groups incorporated into polystyrene chains in polyethyleneoxide(PEO)/1,2-dichloroethane mixtures have been measured by the single photon counting method. The fluorescence depolarization method is very excellent to clarify various dynamical modes of polymer chains, and many theoretical and experimental researches have so far been reported in the field of polymer chain dynamics. However there are few reports about the dynamics on the polymer side chain, because the dynamical mechanism of the polymer side chain is very complicated. In this report we tried to analyze the dynamical modes of the polymer side chains by the fluorescence depolarization method. Five dynamical modes of a polymer chain based on the Wöessner model were estimated by our original analytical technique `χ²-map method'. The value of each mode of a polymer side chain was discussed above the overlap concentration (C^*) of PEO and the micro-environments were clarified in the vicinity of the chromophore attached to the polymer side chain.     

Photoisomerization of cyanine derivatives in 1-butyl-3-methylimidazolium hexafluorophosphate and aqueous glycerol: influence of specific interactions

Photoisomerization of two cyanine derivatives, 3,3(')-diethyloxadicarbocyanine iodide (DODCI) and merocyanine 540 (MC 540), has been investigated in an ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate and aqueous glycerol (93 wt % glycerol +7 wt % water) by measuring fluorescence lifetimes and quantum yields. The aim of this work is to understand how the rates of photoisomerization of DODCI and MC 540 are influenced by specific solute-solvent interactions besides the viscosity of the medium. For DODCI, it has been observed that the nonradiative rate constants, which represent the rates of photoisomerization, are almost identical in the ionic liquid and aqueous glycerol at given temperature, indicating that viscosity is the sole parameter that governs the rate of photoisomerization. In contrast, the photoisomerization rate constants of MC 540 have been found to be a factor of 2 higher in aqueous glycerol compared to the ionic liquid. The observed behavior is due to the zwitterionic character of MC 540, a consequence of which, the twisted state gets stabilized by the solute-solvent hydrogen bonding interactions in aqueous glycerol, thus lowering the barrier for isomerization.     

Defined Picogram Dose Inclusion and Release of Macromolecules using Polyelectrolyte Microcapsules

Summary: Reversible pH‐induced swelling of (PAH/PSS) polyelectrolyte microcapsules is accompanied by increased porosity, making them permeable to poly(acrylic acid) (PAA) at pH values higher than 11.2. This pH‐switchable permeability was used to encapsulate the polyanion in alkaline conditions. Relationship between starting PAA concentration in solution and amount finally being encapsulated has been established and can be used further as calibration curve. A desired amount of encapsulated polymer in the picogram range per capsule can be achieved. The loaded capsules were then used as microreactors by forming a complex between the PAA and Ca²⁺ ions.

General scheme for pH‐induced encapsulation of (PAA) in alkali condition by switching their permeability.     

Stabilization of polymer colloid dispersions with pH-sensitive poly-acrylic acid brushes

Polyelectrolyte brushes are widely used for surface modification of nano-and colloidal particles because of their ability to dramatically change their conformation, hydrophobicity, polarity, charge, etc., as a response to smooth variations in environmental conditions. In this work, we have studied experimentally the stability behavior of polymer colloids with grafted poly-acrylic acid (PAA) surface brushes. We have measured the Fuchs stability ratio (W) as a function of electrolyte concentrations at different pH. It is observed that at pH?<?3, the W values with 1 % and 2 % PAA brushes do not differ significantly from those without PAA, indicating that in their protonated state, the carboxylic groups do not contribute significantly to the colloidal stability. At the intermediate pH?~?5, the PAA brushes are partially deprotonated, and their contribution to the colloidal stability is substantial and increases as the length of the PAA brushes increases. Under alkaline conditions (pH?>?8), since most of the carboxylic groups are ionized, the colloidal stability is much higher than that at pH?~?5. However, the W values are basically the same with 1 % and 2 % PAA, implying that the contribution of the ionized AA in the two cases is practically the same. This experimental evidence indicates that only the ionized AA groups in the outer region of long brushes contribute to colloidal stability, thus supporting the hypothesis of local electroneutrality in the inner region of long brushes (LEA).     

Plasma membrane properties involved in the photodynamic efficacy of merocyanine 540 and tetrasulfonated aluminum phthalocyanine

Merocyanine 540 (MC540)-mediated photodynamic damage to erythrocytes was strongly reduced when illumination was performed at pH 8.5 as compared to pH 7.4. This could be explained by high pH-mediated hyperpolarization of the erythrocyte membrane, resulting in decreased MC540 binding at pH 8.5. In accordance, the MC540-mediated photooxidation of open ghosts was not inhibited at pH 8.5. Photoinactivation of vesicular stomatitis virus (VSV) was not inhibited at pH 8.5. This suggests that illumination at increased pH could be an approach to protect red blood cells selectively against MC540-mediated virucidal phototreatment. With tetrasulfonated aluminum phthalocyanine (AIPcS4) as photosensitizer, damage to erythrocytes, open ghosts and VSV was decreased when illuminated at pH 8.5. A decreased singlet oxygen yield at high pH could be excluded. The AIPcS4-mediated photooxidation of fixed erythrocytes was strongly dependent on the cation concentration in the buffer, indicating that the surface potential may affect the efficacy of this photosensitizer. This study showed that altering the environment of the target could increase both the efficacy and the specificity of a photodynamic treatment.     

Assembly of multilayered films using well-defined, end-labeled poly(acrylic acid): influence of molecular weight on exponential growth in a synthetic weak polyelectrolyte system

We report on the influence of polyanion molecular weight on the growth and structure of multilayered thin films fabricated from poly(allylamine) (PAH) and well-defined, end-labeled poly(acrylic acid) (PAA) synthesized by atom transfer radical polymerization. We observed striking differences in the growth of PAH/PAA films fabricated using well-defined PAA compared to films fabricated using higher molecular weight, commercially available PAA. Past studies demonstrate that the thicknesses of PAH/PAA films increase as linear functions of the number of PAH and PAA layers deposited over a broad range of pH (e.g., from pH 2.5 to 4.5). We observed the thicknesses of films fabricated using solutions of PAH and PAA adjusted to pH 7.5 and 3.5, respectively, to increase in a nonlinear manner. Films fabricated using well-defined, low molecular weight samples of PAA under these conditions increased in thickness exponentially. Experiments using samples of PAA having substantially non-overlapping molecular weight distributions demonstrated a clear relationship between the molecular weight of PAA and rates of film growth. We also used confocal microscopy, in combination with fluorescently end-labeled samples of PAA, to characterize the location of PAA in these assemblies. The results of these experiments, when combined, support the general conclusion that PAA is able to penetrate or diffuse into these films over large distances during assembly. The mechanism of growth for these films thus appears similar to that recently reported for the exponential growth of films fabricated using a variety of biologically relevant polyelectrolytes. The use of living/controlled methods of polymerization to synthesize well-defined samples of PAA facilitates an interpretation of these differences in film behavior as arising largely from differences in polymer molecular weight and polydispersity. This work provides insight into the assembly and structure of a well-studied weak polyelectrolyte film system and illustrates the potential of living/controlled methods of polymerization to contribute to the characterization and understanding of the physical properties of these ionically cross-linked materials.     

Stability of Colloidal Silica Modified by Macromolecular Polyacrylic Acid (PAA) – Application of Turbidymetry Method

The effect of anionic polyacrlic acid (PAA) adsorption on fumed silica (SiO₂) surface on suspension stability was studied. The turbidymetry method was applied to monitor the changes in the suspension stability (using apparatus Turbiscan Lab^Expert with cooling module TLAb Cooler). PAA macromolecules contain dissociable carboxyl groups, therefore, all measurements were carried out at three pH values: 3, 6 and 9. Analysis of obtained transmission and backscattering curves and Turbiscan Stability Indexes (TSI) allowed determination of the most probable mechanism of the stability of the studied systems. The PAA adsorption has the greatest impact on the silica suspension stability at pH 3 (significant improvement of its stability). On the other hand, the presence of polyacrylic acid at pH 6 causes a noticeable deterioration of system stability conditions. At pH 9, polymer minimally influences the stability of SiO₂ suspension.     

Light Scattering Study of the Antibody–Poly(methacrylic acid) and Antibody–Poly(acrylic acid) Conjugates in Aqueous Solutions

The effect of the conformational state of the polymer coil on the properties of protein–polymer conjugates has been studied for the conjugates of antibody (monoclonal antibody from 6C5 clone against inactivated rabbit muscle glyceraldehyde‐3‐phosphate dehydrogenase; Ab) with poly(methacrylic acid) (PMAA) or poly‐(acrylic acid) (PAA). The pH‐dependencies of molecular properties and structural parameters of aqueous solutions (radius of gyration, intensity of scattered light, hydrodynamic diameter, and polydispersity index) of Ab, PMAA, and PAA and their conjugates, i. e., Ab‐PMAA and Ab‐PAA, have been studied using static and dynamic light scattering techniques. While free Ab aggregates in solution and precipitates at its isoelectric point, the covalent attachment of a charged polymer to Ab prevents its association and shifts the precipitation point towards more acidic values (from pH 5.95 for Ab to pH ˜ 4.8 for Ab‐PMAA). The predominant role of the conformational status of the polymer in the process of conjugate precipitation has been considered. Contrary to the precipitation of Ab‐PMAA, the formation of stable colloidal particles was suggested for Ab‐PAA at pH < 4.8. In the conjugates, polymer chains surround the protein globule in an extremely compact manner while Ab significantly affects the polymer conformation. The essentially larger hydrodynamic radii of conjugates, when compared with their radii of gyration, confirm the strong interaction of conjugates with solvent molecules.     

Polymer complexes stabilized through hydrogen bonds. Influence of “structure defects” on complex formation: Viscometry and fluorescence polarization measurements

The structure of polymer complexes stabilized through hydrogen bonds can be much influenced by the presence of nonactive groups (structure defects) on the polymer chains. In this paper two very simple homopolymer/copolymer systems are studied: the homopolymer is a polybase, polyoxyethylene (PEO) or polyvinylpyrrolidone (PVP), and the copolymer a partially neutralized poly(acrylic acid) (PAA). The acrylate groups on PAA chain behave as structure defects. Viscometry provides information about macroscopic structure of polymer complex in solution while fluorescence polarization is especially adapted for the study of the local mobility of polymer chains. Two kinds of structure are found: the first one is compact and implies a low viscosity of the mixture, eventually precipitation occurs, the second one is a highly branched structure, close to a gel, which leads to a very high increase in viscosity. For instance, the viscosity of the mixture may be several hundred times higher than the sum of the viscosities of the two individual polymer solutions. Such mixtures are especially adapted to be used like thickening agents.     

THE PHOTOPHYSICS OF MEROCYANINE 540. A COMPARATIVE STUDY IN ETHANOL AND IN LIPOSOMES

Abstract— Absorption and fluorescence emission spectra, fluorescence lifetimes, fluorescence quantum yields, photoisomerization quantum yields and triplet quantum yields were measured for Merocyanine 540 (MC540) in ethanol and in large unilamellar dimyristoyl phosphatidylcholine vesicles. The major differences in the photophysics between the two media are the increase of the fluorescence quantum yield from 0.15 in ethanol to 0.6 in vesicles at 25° C, and the appearance of a second fluorescence decay with a lifetime of 1.87 ns in the latter medium. Upper and lower limits for the photoisomerization quantum yields were determined by combining the data from laser flash photolysis and optoacoustic spectroscopy. The decrease in photoisomerization quantum yield upon incorporation of the dye into the lipid bilayer by a factor 2 suggests that this process competes directly with fluorescence. The temperature dependence of the fluorescence and photoisomerization quantum yields in solution supports this model. In both media MC540 has a very low triplet quantum yield with values 0.002 > (> ø_T > 0.02 in ethanol and 0.01 > ø_T- > 0.09 in liposomes Our data are consistent with the model whereby the dye is incorporated into the lipid bilayer as a monomer with two different orientations and this model is adopted on the basis of the biexponential behaviour of the fluorescence and photoisomer decay.