Sensitive detection of endocrine disrupters using ionic liquid--single walled carbon nanotubes modified screen-printed based biosensors

Simple and low cost biosensor based on screen-printed electrode for sensitive detection of some alkylphenols was developed, by entrapment of HRP in a nanocomposite gel based on single-walled carbon nanotubes (SWCNTs) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]) ionic liquid. Raman and FTIR spectroscopy, CV and EIS studies demonstrate the interaction between SWCNTs and ionic liquid. The nanocomposite gel, SWCNT-[BMIM][PF₆] provides to the modified sensor a considerable enhanced electrocatalytic activity toward hydrogen peroxide reduction. The HRP based biosensor exhibits high sensitivity and good stability, allowing a detection of the alkylphenols at an applied potential of −0.2 V vs. Ag/AgCl, in linear range from 5.5 to 97.7 μM for 4-t-octylphenol and respectively, between 5.5 and 140 μM for 4-n-nonylphenol, with a response time of about 5 s. The detection limit was 1.1 μM for 4-t-octylphenol, and respectively 0.4 μM for 4-n-nonylphenol (S/N = 3).     

Synthesis of symmetrical and unsymmetrical 3,3-di(indolyl)indolin-2-ones under controlled catalysis of ionic liquids

Three ionic liquids, [BMIM][BF₄] doped with 60 mol % of LiCl ([BMIM][BF₄]-LiCl), N,N,N,N-tetramethylguanidinium trifluoroacetate (TMGT), and N,N,N,N-tetramethylguanidinium triflate (TMGT_f) were found useful as catalyst solvents for controlled 3-indolylation of isatins. Our investigation revealed that the reaction between isatin and indoles in [BMIM][BF₄]-LiCl or TMGT_f media stops at the step of addition of the two components providing 3-indolyl-3-hydroxyindolin-2-ones while the ionic liquid TMGT runs the reaction further through accompanying Friedel-Crafts substitution to afford symmetrical 3,3-di(indol-3-yl)indolin-2-ones. To take advantage of the difference between the effects of these ionic liquids on the reaction progress, we planned a two-step protocol for the efficient synthesis of unsymmetrical 3,3-di(indol-3-yl)indolin-2-ones.     

Effect of ionic liquid organizing ability and amine structure on the rate and mechanism of base induced elimination of 1,1,1-tribromo-2,2-bis(phenyl-substituted)ethanes

The kinetics of the elimination reaction of 1,1,1-tribromo-2,2-bis(phenyl-substituted)ethanes into the corresponding 1,1-dibromo-2,2-bis(phenyl-substituted)ethenes induced by amines were studied in three room temperature ionic liquids ([BMIM][BF₄], [BMIM][PF₆], [BdMIM][BF₄]). In order to have information about reagent-ionic liquid interactions, the reaction was carried out over the temperature range (293.1-313.1 K). To study the effect of the amine on the rate and occurrence of the elimination reaction, several primary, secondary and tertiary amines with different structure (cyclic and acyclic), basicity and steric requirements were used. The data collected show that the reaction occurs faster in ionic liquids than in other conventional solvents. Furthermore, ionic liquids seem to be able to induce, for the studied reaction, a shift of mechanism from E1_cb (in MeOH) versus E2 (in ionic liquid).     

Mild conversion of propargylic alcohols to α,β-unsaturated enones in ionic liquids (ILs); a new ‘metal free’ life for the Rupe rearrangement

A mild and selective transition metal free protocol for the conversion of propargylic alcohols to cyclic and acyclic α,β-unsaturated enones via the Rupe rearrangement is reported. The method utilizes the Brønsted acidic ionic liquid [BMIM-SO₃H][OTf] as catalyst and [BMIM][PF₆] as solvent and offers the potential for recycling and reuse of the IL solvent. The feasibility to synthesize bicyclic fused cyclopentenone derivatives via a Rupe → Aldol → Nazarov sequence utilizing this protocol has also been demonstrated.     

The Synthesis of Anatase TiO2 Nanoparticles by Solvothermal Method using Ionic Liquid as Additive

The solvothermal reactions of Ti(OiPr)₄ in alcohol using ionic liquid as additive were investigated. In the presence of [BMIM][Cl], [BMIM][Br], [BMIM][NTf₂], [BMIM][SO₃Me], [BMIM][SO₄Me], or [BMIM][OTf] (BMIM = 1‐Butyl‐3‐methylimidazolium), pure anatase nanoparticles were obtained. The controlled hydrolysis of Ti(OiPr)₄ in the presence of ionic liquids to form titanium oxo clusters plays a key role in the formation of anatase nanostructures, and ionic liquids can be repeatedly used to synthesise anatase nanoparticles. However, in the presence of [BMIM][PF₆], [BMIM]₂[Ti(OH)₆] was obtained by an anion exchange reaction.     

Separation of aromatic hydrocarbons from alkanes using ammonium ionic liquid C2NTf2 at T = 298.15 K

(Liquid + liquid) equilibrium data are presented for four ternary systems of an alkane, or aromatic compound and ethyl(2-hydroxyethyl)dimethylammonium bis{(trifluomethyl)sulfonyl}imide (C₂NTf₂) at 298.15 K: [hexane + benzene + C₂NTf₂], [hexane + p-xylene + C₂NTf₂], and [hexane, or octane + m-xylene + C₂NTf₂]. The separation of aromatic hydrocarbons (benzene, or p-xylene, or m-xylene) from aliphatic hydrocarbons (hexane, or octane) is investigated by extraction with the ammonium ionic liquid. Selectivities and distribution ratios are discussed for these mixtures at constant temperature. The data were analysed and compared to those previously reported for other ionic liquids and especially for the system {hexane + benzene + [EMIM][NTf₂]}. The nonrandom two liquid NRTL model was successfully used to correlate the experimental tie-lines and to calculate the phase compositions of the ternary systems.     

Application of [EMim][ESO4] ionic liquid as solvent in the extraction of toluene from cycloalkanes: Study of liquid-liquid equilibria at T = 298.15 K

In this paper, the separation of toluene from cycloalkanes by liquid extraction using the ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate, [EMim][ESO₄], as solvent was studied. Liquid-liquid equilibrium (LLE) data for ternary systems {cyclohexane, or cyclooctane, or methylcyclohexane + toluene + [EMim][ESO₄]} were determined at T = 298.15 K and atmospheric pressure. Selectivity and solute distribution ratio, derived from the tie-lines, were used to determine the ability of this ionic liquid as solvent for the separation of toluene from its mixtures with cycloalkanes. The degree of consistency of the tie-lines was tested using the Othmer-Tobias equation, and the experimental LLE data were correlated using the non-random two-liquid (NRTL) and the UNIversal QUAsi-Chemical (UNIQUAC) models.     

Chelation-controlled asymmetric aminohalogenation reaction

The chelation-controlled asymmetric aminohalogenation of α,β-unsaturated 3-aryl-N-acyl-N-4-phenyl-2-oxazolidinones have been established by using palladium(II) acetate as the catalyst and as the chelation metal. The reaction is very convenient to perform by simply mixing the three reactants, cinnamates, N,N-dichloro-p-toluenesulfonamide and catalyst together with 4 Å molecular sieves at rt in any convenient vial of appropriate size without special protection from inert gases. Unlike the previous asymmetric aminohalogenation, the ionic liquid, [BMIM][NTf₂], was found to be superior to [BMIM][BF₄] as the reaction media. It was also found that palladium(II) acetate has to be used together with 1 equiv of MeCN to achieve the opposite chelation control. The resulting absolute stereochemistry of the product was unambiguously determined by X-ray structural analysis.     

Catalytic Conversion of Glucose into Levulinic Acid Using 2-Phenyl-2-Imidazoline Based Ionic Liquid Catalyst

Levulinic acid (LA) is an industrially important product that can be catalytically valorized into important value-added chemicals. In this study, hydrothermal conversion of glucose into levulinic acid was attempted using Brønsted acidic ionic liquid catalyst synthesized using 2-phenyl-2-imidazoline, and 2-phenyl-2-imidazoline-based ionic liquid catalyst used in this study was synthesized in the laboratory using different anions (NO₃, H₂PO₄, and Cl) and characterized using ¹H NMR, TGA, and FT-IR spectroscopic techniques. The activity trend of the Brønsted acidic ionic liquid catalysts synthesized in the laboratory was found in the following order: [C₄SO₃HPhim][Cl] > [C₄SO₃HPhim][NO₃] > [C₄SO₃HPhim][H₂PO₄]. A maximum 63% yield of the levulinic acid was obtained with 98% glucose conversion at 180 °C and 3 h reaction time using [C₄SO₃HPhim][Cl] ionic liquid catalyst. The effect of different reaction conditions such as reaction time, temperature, ionic liquid catalyst structures, catalyst amount, and solvents on the LA yield were investigated. Reusability of [C₄SO₃HPhim][Cl] catalyst up to four cycles was observed. This study demonstrates the potential of the 2-phenyl-2-imidazoline-based ionic liquid for the conversion of glucose into the important platform chemical levulinic acid.     

1-Butyl-3-methylimidazolium-based ionic liquids and an anionic surfactant: Excellent background electrolyte modifiers for the analysis of benzodiazepines through capillary electrophoresis

In this study, we found that adding 1-butyl-3-methylimidazolium-based ionic liquids (ILs) and sodium dodecyl sulfate (SDS) as modifiers in the background electrolyte (BGE) for capillary electrophoresis enhanced the separation of benzodiazepines. In particular, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([BMIM][NTf₂]) was the best IL additive for the separation system because its anionic moiety interacted favorably with the benzodiazepines. We added SDS because of its known effect on the separation of hydrophobic analytes. We optimized the separation conditions in terms of the concentrations of the IL, SDS, and organic solvent, the pH, and the BGE's ionic strength. The optimal BGE, containing 170 mM [BMIM][NTf₂] and 10 mM SDS, provided baseline separation, high efficiency, and satisfactory peak shapes for the benzodiazepines. The separation mechanism was based on heteroassociation between the anionic moiety of the IL and the benzodiazepines, with SDS improving the resolution of the separation. The limits of detection for the seven analytes ranged from 2.74 to 4.42 μg/mL. We subjected a urine sample to off-line solid phase extraction (SPE) prior to the analysis of its benzodiazepine content. Our experimental results reveal that the combination of [BMIM][NTf₂] and SDS provides adequate separation efficiency for its application to CE analyses of benzodiazepines after SPE concentration.     

Liquid structures of 1-butyl-3-methylimidazolium tetrafluoroborate and carbon dioxide mixtures by X-ray diffraction measurements

X-ray diffraction measurements for the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, [BMIM][BF₄], mixed with CO₂ were carried out at high pressures using our developed polymer cell. The intermolecular distribution functions obtained for [BMIM][BF₄]–CO₂ mixtures showed that CO₂ molecules are preferentially solvated to the [BF₄]⁻ anion. The similar preferential solvation was previously observed in analogous 1-btuyl-3-methylimidazolium hexafluorophosphate, [BMIM][PF₆], with a different anion, which is in harmony with the present results in [BMIM][BF₄]–CO₂.     

Measurement and correlation of vapor pressure of benzene and thiophene with [BMIM][PF6] and [BMIM][BF4] ionic liquids

An apparatus used to measure vapor pressure of organic solvents was set up, and vapor pressure of mixture of ionic liquids ([BMIM][PF₆] and [BMIM][BF₄]) and aromatic compounds (benzene and thiophene), with mole fraction of organic solute from 0.1 to 0.75 was measured by using saturation vapor pressure method at temperature from 303 K to 343 K. Then NRTL equation was used to correlate the experimental data. The overall average relative deviation of activity coefficients for the whole system is 2.30%, which indicates that NTRL equation can be utilized to correlate vapor pressure of binary systems containing ionic liquids. The results show that ionic liquids can depress the volatility of aromatic compounds.     

Solubility of carbon dioxide in the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

In this work, the phase behaviour of the binary system of carbon dioxide and the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([emim][Tf₂N]) has been studied experimentally. The equipment used for the experiments is the Cailletet set-up, based on visual observations of phase transitions of systems with constant overall composition. Results are reported for carbon dioxide concentrations ranging from 12.3 to 59.3 mol%, and within temperature and pressure ranges of 310–450 K and 0–15 MPa, respectively. The data reveal an extremely high capacity of the selected ionic liquid for dissolving CO₂ gas, for example, reaching up to about 60 mol% within the above-mentioned pressure and temperature range. Also, the solubility of CO₂ in the ionic liquid [emim][Tf₂N] is compared to the solubility of CO₂ in the ionic liquid [emim][PF₆], an ionic liquid that shares the same cation.     

1-Butyl-2,3-trimethyleneimidazolium bis(trifluoromethylsulfonyl)imide ([b-3C-im][NTf2]): a new, stable ionic liquid

Using imidazole as the starting material, the synthesis of a new bicyclic ionic liquid [b-3C-im][NTf₂] is described. Except for the alkylation reaction in the second step (40% yield) of this four-step synthesis of [b-3C-im][NTf₂], others were all high yielding reactions (85-94% isolated yields). We investigated intrinsic reactivity of this and other imidazolium-based ionic liquids and found that, under strongly basic conditions (KOD in CD₃OD/D₂O (1:1) solution), the new ionic liquid was stable to solvent deuterium isotope exchange while the previously reported [bdmim][NTf₂] and [bdmim][PF₆] ionic liquids were 50% deuterium exchanged at its C-2 methyl in 30 min at ambient temperature. At the same experimental condition, the most commonly employed [bmim][PF₆] ionic liquid was deuterium exchanged instantaneously at its C-2 hydrogen. In the absence of bases (CD₃OD/D₂O = 1:1), only [bmim][PF₆] was deuterium exchanged (50% within 1 h) and other ionic liquids gave no detectable exchanges even after one week at ambient temperature. It is therefore concluded that the new [b-3C-im][NTf₂] ionic liquid is far more chemically stable than previously reported [bmim][PF₆], [bdmim][NTf₂], and [bdmim][PF₆].     

Esterification of (RS)-Ibuprofen by native and commercial lipases in a two-phase system containing ionic liquids

Four commercially available lipases and two native lipases from Aspergillus niger AC-54 and Aspergillus terreus AC-430 were used for the resolution of (RS)-Ibuprofen in systems containing the ionic liquids [BMIM][PF₆] and [BMIM][BF₄]. The lipases showed higher conversion in a two-phase system using [BMIM][PF₆] and isooctane compared to that in pure isooctane. Although the best enzyme was a commercially available lipase from Candida rugosa (E = 8.5), another native lipase, produced in our laboratory, from A. niger gave better enantioselectivity (E = 4.6) than the other lipases tested (E = 1.9–3.3.). After thorough optimization of several reaction conditions (type and ratios of isooctane/ionic liquid, amount of enzyme, and reaction time), the E-value of A. niger lipase (15% w/v) could be duplicated (E = 9.2) in a solvent system composed of [BMIM][PF₆] and isooctane (1:1) after 96 h of reaction.     

Solubility of CO2 in imidazolium-based tetrafluoroborate ionic liquids

The solubility of CO₂ in imidazolium ionic liquids (ILs), 1-butyl-3-methyl imidazolium tetrafluoroborate ([bmim][BF₄]), 1-hexyl-3-methyl imidazolium tetrafluoroborate ([hmim][BF₄]) and 1-octyl-3-methyl imidazolium tetrtafluoroborate ([omim][BF₄]) was determined at 305-25 K and pressures from 1 to 9 MPa. The influence of chain length of alkyl substituents on the imidazolium cation on the solubility of CO₂ was investigated. The differences in solubility with chain length are in the sequence [omim][BF₄] > [hmim][BF₄] > [bmim][BF₄]. The solubility data were correlated by the extended Henry's law, and enthalpy, Gibbs free energy and entropy changes were obtained.     

Solubility of selected dibasic carboxylic acids in water,in ionic liquid of [Bmim][BF4], and in aqueous [Bmim][BF4] solutions

The solubilities of three dibasic carboxylic acids (adipic acid, glutaric acid, and succinic acid) in water, in the ionic liquid of 1-butyl-3-methyl-imidazolim tetrafluoroborate ([Bmim][BF₄]), and in the aqueous [Bmim][BF₄] solutions have been measured by a solid-disapperance method. The binodal curve of water + [Bmim][BF₄] was also determined experimentally from solid–liquid–liquid coexistence temperature up to near the upper critical solution temperature. Experimental results showed that each acid-containing binary behaved as a simple eutectic system. The solid–liquid equilibrium (SLE) data were correlated with the NRTL model for each binary system. The NRTL model with these determined binary parameters predicted the solid-disappearance temperatures of the aqueous ternary mixtures containing [Bmim][BF₄] and the dibasic acids to within an average absolute deviation of 2.0%.     

Thermophysical properties of pure 1-ethyl-3-methylimidazolium methylsulphate and its binary mixtures with alcohols

The density and surface tension of 1-ethyl-3-methylimidazolium methylsulphate, [EMIM][CH₃SO₄] ionic liquid have been measured from (283.15 to 333.15) K. The coefficient of thermal expansion was calculated from the experimental density results using an empirical correlation for T = (283.15-338.15) K. Molecular volume and standard entropies of [EMIM][CH₃SO₄] ionic liquid were obtained from the experimental density values. The surface properties, critical temperature and enthalpy of vaporization were also discussed. Density and surface tension have been measured over the whole composition range for [EMIM][CH₃SO₄] with alcohols (methanol, ethanol, 1-butanol) binary systems at 298.15 K and atmospheric pressure. Excess molar volumes and surface tension deviations for the binary systems have been calculated and were fitted to a Redlich-Kister equation to determine the fitting parameters and the root mean square deviations.     

The Physical Properties of Aqueous Solutions of the Ionic Liquid [BMIM][BF4]

We report here the systematic study of the effect of concentration on the physical properties of aqueous solutions of the room-temperature ionic liquid [BMIM][BF₄]. The measurements of density, ρ, refractive index △n, viscosity η, specific conductivity κ and surface tension, γ, were made over the whole concentration range. The equivalent conductance Λ _m was calculated. The observed linear variations of density and refractive index with the molar concentration are established as those of an ideal solution. The surface tension varied most rapidly in the dilute region whereas the viscosity changed much more rapidly in the concentrated region. Two regions with different composition dependences were found after the analyses of the relationship between the conductivity and the concentration of [BMIM][BF₄]. A proposed model for a structural change in the mixtures was described. The physical origin of the observed concentration dependence of these properties is discussed. The physical properties of the solutions vary with changes of association between anions and cations and the interaction between [BMIM][BF₄] and water.     

Isobaric vapor–liquid equilibria for ethanol–water system containing different ionic liquids at atmospheric pressure

Isobaric vapor–liquid equilibrium (VLE) data for ethanol–water systems containing ionic liquids (ILs) 1-methyl-3-methylimidazolium dimethylphosphate ([MMIM][DMP]), 1-ethyl-3-methylimidazolium diethylphosphate ([EMIM][DEP]), 1-butyl-3-methylimidazolium bromide ([BMIM][Br]), 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]) at atmospheric pressure (101.32 kPa) were measured with a circulation still. The results showed that the VLE of ethanol–water systems in the presence of different ILs was obviously different from that of the IL-free system. All ILs studied showed a salting-out effect, which gave rise to a change of the relative volatility of ethanol, and even to an elimination of the azeotropic point. It was found that the salting-out effect followed the order of [BMIM][Cl] > [BMIM][Br] > [BMIM][PF₆] and [MMIM][DMP] > [EMIM][DEP], which was ascribed to the preferential solvation ability of the ions resulting from the dissociation of the IL.