A new electrochemiluminescent detection system equipped with an electrically controlled heating cylindrical microelectrode

A new electrochemiluminescent (ECL) detection system equipped with an electrically controlled heating cylindrical microelectrode (HME) was developed in this paper. The cylindrical microelectrode made of platinum wire (25 μm in diameter, 6 mm in long) was used as the working electrode of the ECL detection system, the temperature of the electrode could be controlled electrically. The Ru(bpy)₃²⁺-ECL and Ru(bpy)₃²⁺-C₂O₄²⁻-ECL systems were used to evaluate this ECL detection system. The detection limit for oxalate was found to be 3.0 × 10⁻⁴ mol/L when T_e (temperature of the HME) was 22 °C, and found to be 3.0 × 10⁻⁶ mol/L at 80 °C, which indicates that the detection limit can be improved greatly at higher T_e, based on which, it is possible to establish a more sensitive method for measurement of ECL by using a heated microelectrode.     

An electrochemiluminescent sensor for glucose employing a modified carbon nanotube paste electrode

A carbon nanotube paste (CNTP) electrode and a carbon nanotube paste/glucose oxidase (CNTP/GOx) electrode were prepared, and the electrochemiluminescent (ECL) behavior of luminol in the presence of glucose was investigated in detail at each of these electrodes. Compared to the classical carbon paste (CP) electrode, the CNTP electrode incorporating glucose oxidase greatly enhanced the response of the ECL sensor to glucose due to the electrocatalytic activity of the carbon nanotubes, the specificity of the enzymatic reaction, and the sensitivity of the luminol ECL reaction. Under optimal conditions, the electrode was found to respond linearly to glucose in the concentration range 1.0x10(-6) approximately 2.0x10(-3) mol/L, and the detection limit (defined as the concentration that can be detected at a signal-to-noise ratio of 3) was found to be a glucose concentration of 5.0x10(-7) mol/L. The method used to prepare the CNTP/GOx electrode was very convenient, and the electrode surface could be renewed in the case of fouling by simply polishing or cutting it to expose a new and fully active surface. The relative standard deviations (RSD) were found to be 6.8% and 8.9% for the CNTP electrode and the CNTP/GOx electrode (n=6). The electrode retained 95% of its initial response after two weeks.     

Determination of phosphate in water by means of a new electrochemiluminescence technique based on the combination of liquid-liquid extraction with benzene-modified carbon paste electrode

In this paper, it was found that the hydrophobic ion-associated complex of the molybdophosphoric heteropoly acid with protonated butyl-rhodamine B (BRhB) could be formed and was further selectively extracted into the bulk of the paraffin oil-based carbon paste electrode (CPE). At the same time, compared with other modifiers, the benzene-modified CPE created a suitable electrochemiluminescence (ECL) reaction microenvironment for electro-oxidation BRhB to produce the stronger ECL signal when a 1.30 V electrolytic potential was applied to the CPE in the alkaline medium. Based on these findings, a selective and sensitive ECL method for indirectly detecting phosphate was developed. Under the optimum experimental conditions, the ECL intensity was linear with the concentration of phosphate in the range of 2.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ g mL⁻¹. The detection limit was 8.0 × 10⁻¹¹ g mL⁻¹. The proposed method has been applied successfully to the analysis of phosphate in the water samples.     

Application of cement as new electrode material and solid-phase microextraction material demonstrated by electrochemiluminescent detection of perphenazine

Because of its unique pore network, good strength, and low cost, cement was used as a new electrode material and solid-phase microextraction (SPME) material for the first time. It was mixed with carbon to make a new electrode, cement carbon electrode (CCE). The as-prepared CCE was used to demonstrate the application of cement in SPME by Ru(bpy)₃²⁺ electrochemiluminescent detection of perphenazine (PPZ). The calibration plot for PPZ is linear from 1.0 × 10⁻⁹ to 3.0 × 10⁻⁶ M with a detection limit of 3.1 × 10⁻¹⁰ M. The method was successfully applied to the detection of PPZ in urine sample. Cement-based electrode material may also find broad applications in electrochemistry industry, such as electrochemical wastewater treatment.     

New capillary electrophoresis-electrochemiluminescence detection system equipped with an electrically heated Ru(bpy)3(2+)/multi-wall-carbon-nanotube paste electrode

A new capillary electrophoresis-electrochemiluminescence (ECL) detection system equipped with an electrically heated Ru(bpy)(3)(2+)/multi-wall-carbon-nanotube paste electrode (Ru(bpy)(3)(2+)/MWNTPE) was developed. Ru(bpy)(3)(2+) was immobilized in the electrode by directly mixing with the multi-wall-carbon-nanotube paste (MWNTP). This modified electrode could be electrically heated and temperature of the electrode (Te) could be accurately controlled. Tri-n-propylamine (TPrA) was used as coreactant to investigate CE-ECL signals under different conditions. Compared with the conventional electrode at room temperature, the heated electrode has been shown to provide some advantages, such as higher sensitivity, lower RSD, and decreasing width of the peak. Furthermore, wider range of capillary-to-electrode distance and larger-area electrode are a benefit to CE-ECL. In addition, this system has been applied to separation and detection of acephate and dimethoate. The results indicated that the present CE-ECL system coupled with heated modified-electrode could provide high sensitivity, wide linear range, satisfying linear relationship and excellent reproducibility.     

Electrochemical behavior and detection of guanine using a sodium montmorillonite-modified carbon paste electrode

Herein, a sodium montmorillonite-modified carbon paste electrode is described for the electrochemical determination of guanine. Guanine yields a well-defined and very sensitive oxidation peak at the sodium montmorillonite-modified carbon paste electrode. Compared with the unmodified carbon paste electrode, the modified electrode facilitates the electron transfer of guanine, since it notably increases the oxidation peak current and lowers the oxidation overpotential of guanine. Based on this, a simple sensitive reliable electrochemical method is proposed for the detection of guanine after all the experimental parameters, such as solution pH value, sodium montmorillonite content in the carbon paste electrode, accumulation potential, and time, are optimized. Under the optimized conditions, the oxidation peak current of guanine varies linearly with its concentration in the range 5.0×10⁻⁸ to 2.0×10⁻⁵ M and the detection limit (signal-to-noise=3) is 2.0×10⁻⁸ M after 4-min accumulation. This method is successfully demonstrated with urine samples. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 2, pp. 178–182. The text was submitted by the authors in English.     

Ferrocene-mediated carbon paste electrode modified with d-fructose dehydrogenase for batch mode measurement of d-fructose

A mediated modified carbon paste and renewable surface electrode for fructose amperometric measurement based on d-fructose dehydrogenase (FDH) was prepared and optimized. Commercially available ferrocene (FcH) and hydroxymethyl ferrocene (FcCH₂OH) were used as mediators. The substituted FcH showed better linearity and higher sensitivity. The influence of different experimental parameters was studied for optimum analytical performance. The final FDH-modified electrode showed good analytical performance for batch mode measurements of fructose.     

New triiodomercurate-modified carbon paste electrode for the potentiometric determination of mercury

A new tetrazolium-triiodomercurate-modified carbon paste electrode has been described for the sensitive and selective determination of mercury. The electrode shows a stable, near-Nernstian response for 1×10⁻³ to 6×10⁻⁶ M [HgI₃]⁻ at 25 °C over the pH range of 4.0-9.0, with an anionic slope of 55.5±0.4 mV. The lower detection limit is 4×10⁻⁶ M with a fast response time of 30-50 s. Selectivity coefficients of a number of interfering anions and iodo complexes of some metal ions have been estimated. The interference from many of the investigated ions is negligible. The determination of 1-200 μg/ml of mercury in aqueous solutions shows an average recovery of 98.5% and a mean relative standard deviation of 1.6% at 50.0 μg/ml. The direct determination of mercury in spiked wastewater, metal amalgams and dental alloy gave results that compare favorably with those obtained by the cold vapor atomic absorption spectrometric method. Potentiometric titration of mercury and phenylmercury acetate with standard potassium iodide has been monitored using the developed triiodomercurate-carbon paste electrode (CPE) as an end point indicator electrode.     

A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

嵌入式超薄碳糊电极的研究及其应用

在镍铬合金基体上,研制了一种新颖的嵌入式超薄碳糊膜电极。该电极可用作银离子的伏安测定。峰电流与Ag 离子浓度在1.0×10-10～1.0×10-6mol/L范围呈良好的线性关系,检出限为8.0×10-11mol/L。     

An ionic liquid-type carbon paste electrode for electrochemical investigation and determination of calcium dobesilate

An ionic liquid-type carbon paste electrode (IL-CPE) had been fabricated by replacing non-conductive organic binders with a conductive room temperature ionic liquid, 1-pentyl-3-methylimidazolium hexafluorophosphate (PMIMPF₆). The electrochemical responses of calcium dobesilate were investigated at the IL-CPE and the traditional carbon paste electrode (T-CPE) in 0.05 mol L⁻¹ H₂SO₄, respectively. The results showed the superiority of IL-CPE to T-CPE in terms of provision of higher sensitivity, faster electron transfer and better reversibility. A novel method for determination of calcium dobesilate was proposed. The oxidation peak current was rectilinear with calcium dobesilate concentration in the range of 8.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹, with a detection limit of 4.0 × 10⁻⁷ mol L⁻¹(S/N = 3) by differential pulse voltammetry. The proposed method was applied to directly determine calcium dobesilate in capsule and urine samples.     

Characterization of a carbon paste electrode modified with tripolyphosphate-modified kaolinite clay for the detection of lead

We report about the use of carbon paste electrode modified with kaolinite for analytical detection of trace lead(II) in domestic water by differential pulse voltammetry. Kaolinite clay was modified with tripolyphosphate (TPP) by impregnation method. The results show that TPP in kaolinite clay plays an important role in the accumulation process of Pb(II) on the modified electrode surface. The electroanalytical procedure for determination of Pb(II) comprised two steps: chemical accumulation of the analyte under open-circuit conditions, followed by electrochemical detection of the pre-concentrated species using differential pulse voltammetry. The analytical performance of this system has been explored by studying the effects of preconcentration time, carbon paste composition, pH, supporting electrolyte concentration, as well as interferences due to other ions. The calculated detection limit based on the variability of a blank solution (3s_b criterion) for 10 measurements was 8.4 × 10⁻⁸ mol L⁻¹, and the sensitivity determined from the slope of the calibration graph was 0.910 mol L⁻¹. The reproducibility (RSD) for five replicate measurements at 1.0 mg L⁻¹ lead level was 1.6%. The results indicate that this electrode is sensitive and effective for the determination of Pb²⁺.     

A study on the determination of chromium as chromate at a carbon paste electrode modified with surfactants

A procedure for the determination of chromium is described based on synergistic pre-concentration of the chromate anion at a carbon paste electrode modified in situ with quarternary ammonium salts such as 1-ethoxycarbonylpentadecyltrimethylammonium bromide (Septonex^®), cetyltrimethylammonium bromide (CTAB) or cetylpyridinium bromide (CPB). The proper electrochemical detection utilises the reduction Cr(VI) → Cr(III) performed in the differential pulse cathodic voltammetric mode. In discussion, considerable attention has been paid to the accumulation mechanism at the carbon paste electrode in the presence of surfactants. Furthermore, after optimising the corresponding experimental conditions (0.1-0.3 M HCl + 0.1 M NaCl as the supporting electrolyte, 2.5-25 μM as the total concentration of modifier, pre-concentration at +0.7 V versus Ag/AgCl and the stripping from +0.7 to −0.4 V), the analytical performance of the method has been evaluated. The signal of interest was reproducible within ±8% and proportional to the concentration in a range of 0.5-50 μM CrO₄²⁻, with a limit of detection (S/N = 3:1) of about 5×10⁻⁸ M CrO₄²⁻ (with accumulation for 300 s). Interference studies were focused mainly on the species capable of forming ion-pairs with the modifier; i.e., TlCl₄⁻, AuCl₄⁻, PdCl₄²⁻, PtCl₆²⁻, VO₄³⁻, MnO₄⁻ and I⁻. Practical applicability of the method was tested on model solutions via the recovery rates (typically 90-110%) or using selected certified reference materials (tea, bush leaves, clover) and two samples of black tea when the respective results were compared to those obtained by the reference determinations with ICP-AES.     

固态碳糊电极电位法测定利多卡因注射液

本文报道了一种以利多卡因与单质碘形成的缔合物为电活性物的全固态碳糊利多卡因电极,电极的线性响应范围5.0×10-2～4.0×10-5mol.L-1,级差电位为30mV/pC,检测下限为3.0×10-5mol.L-1。该电极响应迅速,重现性好,用该电极测定了盐酸利多卡因注射液中利多卡因的含量,结果与药典法相符。     

高选择性H2O2电化学发光传感器的研制及分析特性研究

提出了基于鲁米诺和醋酸纤维素修饰碳糊电极构建H2O2电化学发光传感器的新方法。在最佳实验条件下,该传感器具有重现性好,抗干扰能力强和选择性好等优点,H2O2浓度在4.0×10-6～4.0×10-5mol L范围内与相对电化学发光强度呈线性关系。该方法测定H2O2的检出限为1.6×10-6mol L,相对标准偏差为1.4%,相关系数为0.9978。     

Voltammetric determination of 2-nitrophenol at a bentonite-modified carbon paste electrode

A bentonite-modified carbon paste electrode has been applied to the determination of 2-nitrophenol by differential pulse voltammmetry. The electrochemical reduction of 2-nitrophenol at –0.8 V is carried out in an artificial sea water-formic acid/sodium formate medium at pH 4. The peak height was found to be dependent on the pH over the range 2–11; the presence of a secondary process was observed in the pH range 8–11. The peak potential showed a dependence on pH, with two linear regions with different slopes. A linear relationship between peak intensity and concentration was obtained in the range 0.07–10 mgl^–1, with a detection limit of 0.03 mg 1^–1 and a coefficient of variation of 1.3% at 5 mg 1^–1. The effects of organic and inorganic species on the 2-nitrophenol determination were studied with a view to testing the resolution of the voltammetric technique. The proposed method has been applied to sea water samples with good results.     

Immobilization of horseradish peroxidase to a nano-Au monolayer modified chitosan-entrapped carbon paste electrode for the detection of hydrogen peroxide

A procedure for fabricating an enzyme electrode has been described based on the effective immobilization of horseradish peroxidase (HRP) to a nano-scaled particulate gold (nano-Au) monolayer modified chitosan-entrapped carbon paste electrode (CCPE). The high affinity of chitosan entrapped in CCPE for nano-Au associated with its amino groups has been utilized to realize the use of nano-Au as an intermediator to retain high bioactivity of the enzyme. Hydrogen peroxide (H₂O₂) was determined in the presence of hydroquinone as a mediator to transfer electrons between the electrode and HRP. The HRP immobilized on nano-Au displayed excellent electrocatalytical activity to the reduction of H₂O₂. The effects of experimental variables such as the operating potential of the working electrode, mediator concentration and pH of measuring solution were investigated for optimum analytical performance by using an amperometric method. The enzyme electrode provided a linear response to hydrogen peroxide over a concentration range of 1.22×10⁻⁵-2.43×10⁻³ mol l⁻¹ with a sensitivity of 0.013 A l mol⁻¹ cm⁻² and a detection limit of 6.3 μmol l⁻¹ based on signal per noise =3. The apparent Michaelis-Menten constant (K_m^app) for the sensor was found to be 0.36 mmol l⁻¹. The lifetime, fabrication reproducibility and measurement repeatability were evaluated with satisfactory results. The analysis results of real sample by this sensor were in satisfactory agreement with those of the potassium permanganate titration method.     

Electrochemical behavior of mesoionic sydnone derivatives at wax-impregnated carbon paste electrode

The-N=N-moiety in the mesoionic 3-phenyl sydnone and its derivatives like tolyl sydnones and anisyl sydnones undergo two-electron irreversible electrochemical reduction in Britton-Robinson (BR) buffer at wax-impregnated carbon paste electrodes. Infrared, nuclear magnetic resonance, and mass-spectral data, used to characterize the reduced product, confirm the proposed mechanism. The pasting liquid at the surface of the electrode is found to decrease the electron-transfer rate and cause a higher overpotential compared to homogeneous electrodes. The influence of variation of pH on the peak current and peak potentials is studied in the acidic range. The cathodic peak shifts to more negative potentials with increase in pH, indicating the involvement of proton in the reduction process. This could be a new method of preparation of 2,4-dihydro-3-substituted 1,2,3-oxadiazole-5-one. The substituent effect and the effect of variation of scan rate, concentration, and temperature on peak currents and peak potentials is discussed. The cathodic shift in various organic co-solvents (methanol, acetonitrile, DMF, DMSO) using BRB as the supporting electrolyte is examined. Published in Russian in Elektrokhimiya, 2006, Vol. 42; No. 7, pp. 862–868. The text was submitted by the authors in English.     

Study on the adsorptive catalytic voltammetry of aloe-emodin at a carbon paste electrode

Recently, the studies and applications for the pola-rographic catalytic waves of organic compounds at dropping mercury electrode made considerable head-way. Tovopova et al.[1―4] reported the polarographic catalytic waves of the organic compounds containi…