Speciation of Cr(III) and Cr(VI) in Environmental Samples after Solid Phase Extraction on Amberlite XAD–2000

A method for speciation of Cr(III) and Cr(VI) in real samples has been developed. Cr(VI) has been separated from Cr(III) and preconcentrated as its pyrrolidinedithiocarbamate (APDC) complex by using a column containing Amberlite XAD–2000 resin and determined by FAAS. Total chromium has also been determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with KMnO₄. Cr(III) has been calculated by subtracting Cr(VI) from the total. The effect of pH, flow‐rate, adsorption and batch capacity and effect of various metal cations and salt anions on the sorption onto the resin were investigated. The adsorption is quantitative in the pH range of 1.5–2.5, and Cr(VI) ion was desorbed by using H₂SO₄ in acetone. The recovery of Cr(VI) was 97 ± 4 at a 95% confidence level. The highest preconcentration factor was 80 for a 200 mL sample volume. The adsorption and batch capacity of sorbent were 7.4 and 8.0 mg g^?1 Cr(VI), respectively, and loading half time was 5.0 min. The detection limit of Cr(VI) is 0.6 μg/L. The procedure has been applied to the determination and speciation of chromium in stream water, tap water, mineral spring water and spring water. Also, the proposed method was applied to total chromium preconcentration in microwave digested moss and rock samples with satisfactory results. The developed method was validated with CRM‐TMDW‐500 (Certified Reference Material Trace Metals in Drinking Water) and BCR‐CRM 144R s (Certified Reference Material Sewage Sludge, Domestic Origin) and the results obtained were in good agreement with the certified values. The relative standard deviations were below 6%.     

Speciation of Cr(III) and Cr(VI) in waters using immobilized moss and determination by ICP-MS and FAAS

The possibility of using moss (Funaria hygrometrica), immobilized in a polysilicate matrix as substrate for speciation of Cr(III) and Cr(VI) in various water samples has been investigated. Experiments were performed to optimize conditions such as pH, amount of sorbent and flow rate, to achieve the quantitative separation of Cr(III) and Cr(VI). During all the steps of the separation process, Cr(III) was selectively sorbed on the column of immobilized moss in the pH range of 4-8 while, Cr(VI) was found to remain in solution. The retained Cr(III) was subsequently eluted with 10 ml of 2 mol l⁻¹ HNO₃. A pre-concentration factor of about 20 was achieved for Cr(III) when, 200 ml of water was passed. The immobilized moss was packed in a home made mini-column and incorporated in flow injection system for obtaining calibration plots for both Cr(III) and Cr(VI) at low ppb levels that were compared with the plots obtained without column. After separation, the chromium (Cr) species were determined by inductively coupled plasma mass spectrometry (ICP-MS) and flame atomic absorption spectrometry (FAAS). The sorption capacity of the immobilized moss was found to be ∼11.5 mg g⁻¹ for Cr(III). The effect of various interfering ions has also been studied. The proposed method was applied successfully for the determination of Cr(III) and Cr(VI) in spiked and real wastewater samples and recoveries were found to be >95%.     

On-line speciation and determination of Cr(III) and Cr(VI) in drinking and waste water samples by reversed-phase high performance liquid chromatography coupled with atomic absorption spectrometry

A simple, rapid, and selective on-line method for the speciation and determination of Cr(III) and Cr(VI) in aqueous solutions by ion-pairing HPLC coupled with flame atomic absorption spectrometry (FAAS) is described. The composition of the mobile phase has been optimized for better separation. The effects of column temperature, volume of injection loop, fuel flow rate of FAAS, and nebulizer suction rate of FAAS have also been investigated. Separation is accomplished in almost 2.5 min on a 25 cm length C18 column at 40 degrees C. The selectivity of the method has been established by investigating the effect of interfering elements on chromium determination. The detection limit (3sigma) achieved by the method was calculated as 3.7 ng/mL for Cr(III) and 2.0 ng/mL for Cr(VI). The proposed method has been validated by analyzing certified reference material (BCR 544) and successfully applied to the analysis of drinking water and wastewater samples with a relative error below 6%.     

Speciation of Cr(III) and Cr(VI) in water after preconcentration of its 1,5-diphenylcarbazone complex on amberlite XAD-16 resin and determination by FAAS

A simple and sensitive method for the speciation, separation and preconcentration of Cr(VI) and Cr(III) in tap water was developed. Cr(VI) has been separated from Cr(III) and preconcentrated as its 1,5-diphenylcarbazone complex by using a column containing Amberlite XAD-16 resin and determined by FAAS. Total chromium has also been determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with KMnO₄. Then, Cr(III) has been calculated by subtracting Cr(VI) from the total. The effect of acidity, amount of adsorbent, eluent type and flow rate of the sample solution on to the preconcentration procedure has been investigated. The retained Cr(VI) complex was eluated with 10 ml of 0.05 mol l⁻¹ H₂SO₄ solution in methanol. The recovery of Cr(VI) was 99.7±0.7 at 95% confidence level. The highest preconcentration factor was 25 for a 250 ml sample volume. The detection limit of Cr(VI) was found as 45 μg l⁻¹. The adsorption capacity of the resin was found as 0.4 mg g⁻¹ for Cr (VI). The effect of interfering ions has also been studied. The proposed method was applied to tap water samples and chromium species have been determined with the relative error <3%.     

Speciation of Cr(VI)/Cr(III) in environmental waters by fluorimetric method using central composite, full and fractional factorial design

In this approach a fluorometric technique has been developed to study chromium speciation, based on optimised conditions using chemometric methods of experimental design and central composite design. Full and fractional factorial design was used for evaluation of the effective factors in determination of Cr(VI) by fluorometric using Rhodamine-6G in the presence of H₂SO₄. Theory and methodology of a central composite design as a chemometric method for the optimisation of analytical procedures were developed in this approach. It was found that the analytical performance for measurement at the point of optimum in this technique is superior and more accurate than that of one variable at a time. Cr(VI) and Cr(III) were measured in a wastewater sample using the proposed technique. The results confirm the selective determination and speciation of Cr(VI)/Cr(III).     

Simultaneous Determination of Cr(III) and Cr(VI) in Ground and Drinking Waters by IC-ICP-MS

Abstract

The coupling of ion chromatography (IC) and inductively-coupled plasma mass spectrometry (ICP-MS) provides a powerful tool for the simultaneous determination of Cr(III) and Cr(VI) in water samples. The experimental set-up of the technique is described in detail and performance data are given, whereby detection limits of 0.1 μg/l could be achieved for both chromium species without pre-concentration. With this method, a complete analysis can be done in less than 3 minutes. In order to improve the repeatability of the method, Rh(III) as internal standard is used. Stability of the two chromium species in water turned out to be a major problem and optimal conditions for storage were determined. For real water samples storage at 4 °C in the dark at neutral pH and analysis as fast as possible is recommended. The application of the IC-ICP-MS technique to real water samples and the comparison to another, more time-demanding and less sensitive method proves the capacity of the method.     

Cr(III)/Cr(VI) speciation in aerosol particles by extractive separation and thermal ionization isotope dilution mass spectrometry

 An isotope dilution mass spectrometric (IDMS) method, using the formation of positive thermal ions, was developed for Cr(III) and Cr(VI) speciation in aerosol particles. Cr(III) and Cr(VI) spike species, enriched in ⁵³Cr, were applied for the isotope dilution step. After leaching of filter collected aerosol samples by an alkaline solution at pH 13, species separation was carried out by extraction with a liquid anion exchanger in methyl isobutyl ketone. Cr(VI) in the organic phase was re-extracted into an ammoniacal solution and chromium was then isolated from both fractions of species by electrodeposition. Detection limits of 30 pg/m³ for Cr(III) and of 8 pg/m³ for Cr(VI) were achieved in atmospheric aerosols for volumes of air samples of about 120 m³. These low detection limits allowed the determination of chromium species in continental aerosol particles in dependence on different seasons. The Cr(III) /Cr(VI) ratio was always found to be about 0.3 whereas dust from soil erosion, which is probably the primary source of chromium in the atmosphere, showed higher ratios. This indicates that chromium is oxidized in the atmosphere. The accuracy of the method was demonstrated in two interlaboratory comparisons of Cr(VI) determinations in welding dust samples. The IDMS method also contributed to the certification of a corresponding standard reference material organized by the Standard Reference Bureau of the European Union. Chromium speciation, including the determination of elemental chromium Cr(0), was carried out in aerosols of different welding processes for stainless steel. These analyses showed distinct differences in the distribution of chromium species in the welding process and can be used as an exact calibration method for routine methods in this important field of monitoring corresponding working places. Received: 19 August 1996/Revised: 24 September 1996/Accepted: 28 September 1996     

Speciation of Cr(III) and Cr(VI) by Means of Melamine-Urea-Formaldehyde Resin and FAAS

 A method is described for the quantitative preconcentration and separation of trace chromium in water by adsorption on melamine-urea-formaldehyde resin. Cr(VI) is enriched from aqueous solutions on the resin. After elution the Cr(VI) is determined by FAAS. The capacity of the resin is maximal at ∼ pH 2. Total chromium can be determined by the method after oxidation of Cr(III) to Cr(VI) by hydrogen peroxide. The relative standard deviations (10 replicate analyses) for 10 mg/L levels of Cr(VI), Cr(III) and total chromium were 1.5, 3.5 and 2.8% respectively. The procedure has been applied to the determination and speciation of chromium in lake water, tap water and chromium-plating baths.     

Preconcentration extractive separation, speciation and spectrometric determination of iron(III) in environmental samples

Preconcentration, speciation and separation with solvent extraction of Fe(III) from samples of different origin, using methyl isobutyl ketone (MIBK) as a solvent and the sodium salt of 2-carboethoxy-1,3-indandione (CEIDNa) as a complexing agent for Fe(III), were studied. CEIDNa reacts with Fe(III) in the pH range 1.5–3.5 to produce a red colored complex of Fe(III)–CEIDNa (1:3 molar ratio) soluble in MIBK. The investigation includes a study of the characteristics that are essential for solvent extraction, spectrophotometric and flame atomic absorption spectrometric determination (AAS) of iron. A highly sensitive, selective and rapid spectrometric method is described for the trace analysis of iron(III) by CEIDNa. The complex formed obeys Beer's law from 0.06 to 1.8 mg l⁻¹ with an optimum range. A single step extraction was efficiently used with a distribution ratio (D)=10^3.6. The extracted red colored (1:3) Fe–CEIDNa was measured spectrophotometrically at 500 nm with a molar absorptivity of 1.2×10⁴ l mol⁻¹ cm⁻¹. In addition, the organic phase was directly aspirated to the flame for AAS determination and the signals related to Fe(III) concentration were recorded at 243.3 nm. The complexation of iron(III) with CEIDNa allows the separation of the analyte from alkali, alkaline earth and other elements, which are not complexed. The proposed preconcentration procedure was applied successfully to the determination of trace Fe(III) in soil, milk and natural water samples.     

Fluorimetric Cr(VI) and Cr(III) Speciation With Crystal Violet

Abstract

A simple fluorimetric determination of Cr(VI) in the presence of Cr(III) is described. This determination is based on the fluorescence, produced from the ion-association complex between the Crystal violet cation and the anionic complex, formed between Cr(VI) and excess of I^?. This fluorescence is not observed when Cr(III) is used instead of Cr(VI). The fluorescence intensity is linear over the concentration range of 0–60 μg/1. The method was applied in potable and sea waters.     

Preconcentration and separation of Cr(III) and Cr(VI) using sawdust as a sorbent

A simple, inexpensive method based on solid-phase extraction (SPE) on sawdust from Cedrus deodera has been developed for speciation of Cr(III) and Cr(VI) in environmental water samples. Because different exchange capacities were observed for the two forms of chromium at different pH—Cr(III) was selectively retained at pH 3 to 4 whereas Cr(VI) was retained at pH 1—complete separation of the two forms of chromium is possible. Retained species were eluted with 2.5 mL 0.1 mol L⁻¹ HCl and 0.1 mol L⁻¹ NaOH. Detection limits of 0.05 and 0.04 μg mL⁻¹ were achieved for Cr(III) and Cr(VI), respectively, with enrichment factors of 100 and 80. Recovery was quantitative using 250 mL sample volume for Cr(III) and 200 mL for Cr(VI). Different kinetic and thermodynamic properties that affect sorption of the chromium species on the sawdust were also determined. Metal ion concentration was measured as the Cr(VI)–diphenylcarbazide complex by UV–visible spectroscopy. The method was successfully applied for speciation of chromium in environmental and industrial water samples.     

Coupling of microwave induced plasma optical emission spectrometry with HPLC separation for speciation analysis of Cr(III)/Cr(VI)

Feasibility and limitations of direct coupling of high performance liquid chromatographic (HPLC) separation to microwave induced plasma (MIP)-optical emission spectrometry (OES) for elementspecific detection was tested and compared to inductively coupled plasma (ICP)-optical emission spectrometric detection on the basis of the Cr(III)/Cr(VI) speciation analysis of water samples. Coupling was performed by a hydraulic high pressure nebulizer (HHPN) radiative-heating/watercooling interface which provides about 20 % and 80 % aerosol yield in the case of helium and argon carrier gases, respectively. Desolvation efficiency of aqueous solutions was approximately 80 %. Applying the ion-pair HPLC separation, the organic eluents and reagents in the MIP cause a 50–75 % signal suppression for Cr(VI) and 25–50 % for Cr(III). In a pure aqueous solution the MIP Cr(VI) signal was by 20 % lower than that of Cr(III). These effects were lower using the ICP source, but they cannot be neglected. Easily ionizable matrix elements (Na, Ca) can cause 70 % signal suppression in the MIP, and 20 % in the ICP. Therefore, species dependent calibration is required in both cases. In the case of HPLC detection by MIP-OES, the detection limit was 13 ng for Cr(III), and 18 ng for Cr(VI). Using the ICP-OES detection, the detection limit was 0.2 ng for Cr (III) and 0.4 ng for Cr (VI). The linear dynamic ranges in both cases were two orders of magnitude. Presented at the XVIIIth Slovak Spectroscopic Conference, Spišská Nová Ves, 15–18 October 2006.     

Cr(III) and Cr(VI) speciation measurements in environmental reference materials

The production of reference materials for quality control of Cr(III) and Cr(VI) speciation in environmental samples is described. It concerns in the first place two lyophilized solutions containing Cr(III) and Cr(VI) at different concentrations, respectively representative for drinking water and filter leaching solutions, and in the second place filters loaded with welding dust. Twenty-four laboratories with experience in the field participated in an intercomparison exercise organized to validate the suitability of the reference materials and to gauge the state-of-the-art of Cr speciation throughout Europe. The outcome of this exercise is discussed.     

Separation of Cr(III) and Cr(VI) using melamine-formaldehyde resin and determination of both species in water by FAAS

A method is described for the determination of Cr(VI) and total chromium by FAAS. Cr(VI) is separated from Cr(III) by adsorption on melamine-formaldehyde resin. After elution of Cr(VI) with 0.1 mol/l NaAc solution, it is analysed by FAAS. Total chromium is determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with hydrogen peroxide, total Cr(VI) is concentrated as above. If the total concentration of chromium is sufficient, the determination can be directly made by FAAS. Cr(III) can then be calculated by subtracting Cr(VI) from the total Cr. This method was successfully applied to the determination of chromium in lake water.     

Column chromatographic speciation of chromium for Cr(VI) and several species of Cr(III)

Summary Chromium can be present in aqueous solution as Cr(VI) or in monomeric, dimeric, trimeric and higher polymeric forms of Cr(III). Many monomeric forms of Cr(III) are possible, with the water molecules of Cr(H₂O) ₆ ³⁺ substituted by anionic or neutral species. This proliferation of Cr(III) species makes the complete speciation of chromium a continuing challenge to the analyst. A simple and effective cation exchange procedure for the separation of various of these species uses a small glass column containing 1 mL of pre-treated cation exchange resin (Na⁺ form). Stepwise elution with solutions of perchloric acid, Ca²⁺ (pH=2) and La³⁺ (pH=2) separates Cr(VI) and seven Cr(III) species from CrX₃ to tetramer. Radiometric (Cr-51), spectrophotometric and other detection methods can be employed; the use of radiochromium gives the lowest detection limit.     

Simultaneous determination of Cr(III) and Cr(VI) in water by reversed phase HPLC,after chelating with sodium diethyldithiocarbamate

Summary A method for simultaneous determination of Cr(III) and Cr(VI), using sodium diethyldithiocarbamate as chelating agent is given. At room temperature and pH 5.8 sodium diethyldithiocarbamate reacts with both Cr(III) and Cr(VI). Examination of this reaction by reversed phase high-performance liquid chromatography, makes it possible to correct for the interference between Cr(III) and Cr(VI) when determining the amount of Cr(III) present in the solution.     

Chemical speciation of chromium(III,VI) employing extractive spectrophotometry and tetraphenylarsonium chloride or tetraphenylphosphonium bromide as ion-pair reagent

A simple and accurate extractive spectrophotometric procedure for the chemical speciation of chromium(III,VI) species in aqueous media has been developed. The method is based upon the extraction of the complex ion-associate formed between the chloro chromate (CrO₃Cl⁻) anion and the ion-pair reagent tetraphenylarsonium chloride (TPAs⁺Cl⁻) or tetraphenylphosphonium bromide (TPP⁺Br⁻) at pH ≤ 0 in chloroform followed by direct spectrophotometric measurement at 355 nm. The optimum concentration range evaluated by Beer-Lambert's law, Ringbom's plot, the molar absorptivity, the Sandell's sensitivity, the extraction and stability constants (K_D, K_ex and β), the stoichiometry and the extraction equilibria of the produced complex ion-associates have been determined and gave a convenient applications of the investigated system for analytical purposes. Chromium(III) was also determined by the proposed procedure after prior oxidation to chromate with H₂O₂ in alkaline solution. The method has been applied successfully for the analysis of chromium(VI) and total chromium(III,VI) in industrial wastewater of electroplating plant.     

Separation and speciation of Cr(III) and Cr(VI) with Saccharomyces cerevisiae immobilized on sepiolite and determination of both species in water by FAAS

A rapid, sensitive and accurate method for the separation, preconcentration and determination of Cr(III) and Cr(VI) in water samples is described. Chromium species can be separated by biosorption on Saccharomyces cerevisiae immobilized on sepiolite and determined by flame atomic absorption spectrometry (FAAS). The optimum conditions for separation and preconcentration (pH, bed height, flow rate and volume of sample solution) were evaluated. Recovery of the chromium was 96.3+/-0.2% at 95% confidence level. The breakthrough capacity of the adsorbent was found as 228 mumol g(-1) for Cr(III). The proposed method was applied successfully to the determination of Cr(III) and Cr(VI) in spiked and river water samples.     

Preconcentration and speciation of chromium using a melamine based polymeric sequestering succinic acid resin: its application for Cr(VI) and Cr(III) determination in wastewater

A new melamine based polymeric sequestering resin was prepared for preconcentration and separation of hexavalent chromium from water, and its sequestering action was investigated. The water-insoluble, cross-linked sequestering resin was formed by reaction with bromosuccinic acid and cross-linking of melamine. The active sequestering group on the resin is NH-(Succinic acid) or salt thereof. The resulting chelating resin was characterized by infrared spectra. The newly prepared resin quantitatively retained Cr(VI) at pH 2.0-4.0 when the flow rate was maintained between 1 and 5 ml min⁻¹. The retained Cr(VI) was instantaneously eluted with 25 ml of 0.1 M NaOH. The chromium species were determined by a flame atomic absorption spectrometer. The limits of detection for Cr(VI) and Cr(III) were found to be 5.3 and 4.2 μg l⁻¹, respectively. The precision and accuracy of the proposed procedure was checked by the use synthetic and reference steel samples. The established preconcentration method was successfully applied to the determination and selective separation of Cr(VI) in electroplating industry wastewater. Total concentrations determined by the spectrophotometric method (110.3±0.6 g l⁻¹ Cr(VI) and 1.2±0.3 g l⁻¹ Cr(III)) are compared with those found by FAAS and the obtained results (110.4±1.8 g l⁻¹ Cr(VI) and 1.4±0.5 g l⁻¹ Cr(III)) show good agreement.