污水处理工艺对污泥热处理特性的影响

通过10℃/min时的热重分析,对五种不同性质污泥分别在氮气和氧气气氛下的热解和燃烧特性进行了研究。结果表明,污水处理工艺的“好氧+厌氧”、“厌氧+好氧”过程以及污泥的厌氧消化均使污泥中的有机物结构复杂,导致污泥热解时有机物的分解和析出温度升高,且“好氧+厌氧”过程使污泥中有机物结构更复杂;而对污泥的燃烧过程和燃尽点无影响,但使着火温度升高。利用šatava-šesták 方程对污泥热解、燃烧的反应机理进行了研究。结果表明,五种污泥热解时均呈现为挥发分扩散和随后的化学反应机理函数,而燃烧时则为化学反应和随后的扩散过程。     

改性污泥与无烟煤成浆性的研究

采用阴离子表面活性剂萘磺酸钠甲醛缩合物、聚羧酸钠作为分散剂,考察了不同污泥用量时污泥煤浆的成浆性能。结果表明,当污泥(干基)添加量为煤质量的4%时,成浆浓度超过60%,随着污泥用量的提高,污泥煤浆的成浆浓度降低。污泥加入后,浆体的稳定性增强,污泥比例越高,产生沉淀的时间延长。当污泥(干基)添加量为煤质量的4%时,产生沉淀的时间超过160h,与使用稳定剂效果相当。使用不同添加剂制备的污泥煤浆均呈假塑性。污泥疏松的絮状结构,蜂窝状的外表面,强大的吸水性是造成污泥煤浆成浆浓度下降,稳定性增加的主要原因。     

污泥与煤共热解过程中磷元素的挥发规律研究

污泥灰分中磷元素含量明显高于煤,其中主要的晶体态含磷化合物为磷酸铁钙和少量的磷酸铝。利用高频加热反应装置考察了污泥-神府煤混合物快速热解过程中磷元素挥发规律。结果表明,污泥-神府煤混合物热解后磷元素主要存在于热解焦中。磷元素挥发比例随污泥添加比例的增加先升高后降低,随热解温度的升高而增加。热解温度不高于1 100 ℃时,混合物中以有机磷的挥发为主,磷元素挥发比例不高于3.2%。热解温度高于1 200 ℃后无机磷中磷元素挥发明显,1 300 ℃下最高有33.0%的磷元素随热解气体挥发出。     

污泥干燥预处理后与神府煤共成浆性的研究

以萘系阴离子表面活性剂为分散剂,考查了污泥干燥条件和粒径对神府煤成浆性的影响。结果表明,将污泥干燥后再制浆,明显提高了污泥煤浆的成浆浓度;升高干燥温度,有利于提高污泥煤浆的成浆浓度。干燥温度对污泥的可磨性影响较大。干燥温度越高,干燥污泥可磨性越好,球磨的污泥平均粒径越小,制得的污泥煤浆表观黏度越低;温度高于105℃,污泥的可磨性无明显差别,污泥煤浆的表观黏度亦无明显变化。污泥粒径越小,颗粒越细,一定程度上提高了煤粉的堆积效率,使污泥煤浆的表观黏度降低。     

Pyrolysis study of sewage sludge by TG-MS and TG-GC-MS coupled analyses

The pyrolysis of an urban plant sewage sludge carried out under He atmosphere was studied by thermogravimetric-mass spectrometric (TG-MS) and thermogravimetric-gas chromatographic-mass spectrometric (TG-GC-MS) analyses. The sludge was thermally degraded with a heating rate of 10°C min^–1 in the 20–1000°C interval; its mass loss is 51.8% up to 600°C and 61.4% up to 1000°C. Gas chromatographic analyses of the gas released during major thermogravimetric events allow the identification of various chemical species. Water, carbon mono- and di-oxide, several hydrocarbons (up to C5, both saturated and unsaturated) were the major detected species. Minor amount of pollutant species, such as cyano-compounds, were also detected. Among the released species hydrocarbons constituted the major fraction (53%), thus suggesting their immediate exploitation as fuel gas. The pyrolysis behaviour of this sample was then compared with other sewage sludge arising from wastewater treatment plants subjected to anaerobic digestion as found in literature data.     

污泥化学链燃烧过程中氮迁移转化特性研究

在单流化床反应器上探究了污泥化学链燃烧过程中氮迁移转化特性。由于赤铁矿载氧体反应活性低,采用30%水泥对其改性。结果表明,水泥改性可提高污泥热解气化反应速率以及赤铁矿还原反应速率,进而提高污泥碳转化率,但是NO生成率也增加。随着反应温度的升高,污泥的碳转化率和NO生成率均增加。另外,随着水蒸气浓度的增加,碳转化率增加,同时可降低NO生成。在污泥化学链燃烧过程中,NO生成率为0.286%-0.768%,低于污泥空气焚烧氮氧化物排放量。     

污泥微波高温热解条件下富氢气体生成特性研究

分别采用单模微波炉和电加热管式炉对污泥热解过程进行了实验研究,分析了污泥粒径、含水率、热解温度和微波吸收剂形态等参数对热解产物分布特性和气体组分浓度的影响规律和机理。结果表明,在粒径0~5.00 mm,污泥粒径大小对污泥微波热解产物分布无明显影响,但粒径减小可以提高H₂和CO浓度,当粒径从2.50~5.00 mm减小至小于0.45 mm,H₂和CO体积分数分别从31%和17%上升至34%和22%;污泥含水率和微波热解温度对热解产物分布和热解气组分浓度分布都有显著影响,提高污泥含水率或微波热解温度都可以显著提高H₂和CO浓度,当污泥含水率从0上升至83%,H₂和CO体积分数分别从32%和20%上升至42%和31%;相比粉末态吸波剂,固定形态的微波吸收器可以提高挥发分向热解气的转化,提高热解气产量,同时还能略微提高H₂和CO产率,但效果并不明显。     

Kinetic monitoring of trisubstituted organotins in soil after sewage sludge application

Organotin compounds (OTC) are widely used for their biocidal effects in various agricultural or industrial activities, leading to their environmental presence. Among the organotin species, tributyltin (TBT) and triphenyltin (TPhT) are the most used and are generally considered the most toxic. So it is important to understand their behaviour in soils and obtain data about their persistence and phytoavailability. Many works deal with OTC speciation in various matrices, but few are concerned with OTC degradation in soil. The present study focuses on kinetic monitoring of TBT and TPhT in an agricultural soil. These compounds were introduced into the soil by the way of spiked sewage sludge, simulating agricultural practice and diffuse contamination. The influence of time and initial OTC concentration on the species preservation was evaluated. TBT concentration was shown to have a positive effect on TBT preservation. Corresponding half‐lives were calculated. They were 6 ± 1 days and over 39 days for TPhT and TBT, respectively. Degradation compounds, mono‐ and dibutyltin, and mono‐ and diphenyltin, were produced by both direct and successive dealkyl and dearylation processes. Copyright © 2008 John Wiley & Sons, Ltd.     

微波消解-磷钼蓝分光光度法测定城市污泥中总磷浓度

建立了微波消解-磷钼蓝分光光度法测定城市污泥中总磷的方法。在微波环境中硝酸-过氧化氢能够将城市污泥中无机磷盐和含磷有机物消解为正磷酸盐,在弱酸性条件下,正磷酸盐在铋盐的催化条件下与钼酸铵-抗坏血酸生成磷钼蓝,于分光光度计波长690nm处进行测定总磷浓度。方法的相对标准偏差0.63%～0.95%,加标回收率为101%～102%,能够满足对城市污泥中总磷浓度的测定要求。     

污泥水分含量对其空气气化特性的影响(英文)

利用外热式下吸固定床气化实验装置,研究了在一定的空气流量(0.05 m3/h)、气化温度(800℃)下污泥水分含量对3种不同性质污泥空气气化特性的影响。结果表明,气化气中CO2、CH4和H2含量、气化气热值以及水相生成量均随污泥水分含量的增加而增加,而CO含量和焦油生成量呈降低趋势。污泥厌氧消化使气化气中CO、CH4、H2、CmHn含量以及气化气品质降低;而污水处理工艺中的厌氧过程可改善气化气品质,其中来自A2/O工艺消化污泥的气化气品质高于普通活性污泥法消化污泥的气化气品质。随着污泥水分含量的增加,2种不同污水处理工艺产生的消化污泥气化气中CO、CO2和H2含量的差距逐渐加大,来自于同一A2/O工艺的消化与未消化污泥气化气中H2和CO2含量的差距亦逐渐加大,而消化与未消化污泥气化气中CO含量的差距则逐渐接近。     

污水污泥空气气化特性的研究

利用外热式下吸固定床气化实验装置,以空气为气化剂对五种不同性质污泥的气化特性进行了研究。结果表明,升高气化温度有利于提高气化气的品质,气化气中CO、CH₄和H₂的含量和气化气热值随气化剂流量的减小而增加。污泥厌氧消化过程使气化气品质降低;污水处理工艺对污泥气化气组成和热值亦产生影响,其中连续SBR工艺的未消化污泥气化气中CO、CO₂的含量最高,而H₂、CH₄和C_mH_n的含量最低;活性污泥法的未消化污泥气化气中H₂和C_mH_n含量最高;A²/O工艺的未消化污泥气化气中CO、CO₂的含量最低,而CH₄的含量最高,且三个污水工艺污泥的气化气热值依次升高。     

污泥与煤和煤矸石共燃特性研究

利用STA 409 PC型同步热分析仪,对煤、煤矸石和污泥不同质量比样品的燃烧过程进行了热重分析。结果表明,单一煤和煤矸石的DTG曲线都只有一个明显的失重峰,污泥的DTG曲线有两个明显的失重峰,而混合物的DTG曲线都有两个失重峰。通过分析不同样品的混燃过程,发现随着煤所占质量比的增加,最大失重峰速率所对应的温度都有所降低。煤、煤矸石、污泥及其混合物的活化能为16.93kJ/mol～109.89kJ/mol。随着污泥所占质量比的增加,混合物的着火温度有所降低,当达到70%时,污泥与煤混合物的着火点接近单一污泥的着火点。     

基于水泥修饰的赤铁矿载氧体污泥化学链燃烧特性研究

采用水泥修饰赤铁矿来提高载氧体的反应活性。实验在1kW_th串行流化床上进行,研究了添加水泥对污泥化学链燃烧特性的影响,考察其长期运行的物化性能。结果表明,在实验工况下,赤铁矿添加水泥后,出口的未燃气体浓度明显下降。燃料反应器温度低于870℃时,水泥的添加使污泥的碳转化率和燃烧效率显著升高。在10h长期运行后,一部分污泥灰沉积在载氧体表面。虽然在反应过程中部分的Fe₂O₃被深度还原,但在长期运行中未出现流化问题和烧结现象。     

一种煤与两种城市污水污泥混合热解的热重分析

采用热重分析法对一种煤和两种城市污水污泥（S1和S2）及其混合物进行了热解实验研究,揭示了煤和污泥在氮气中的热解特性及污泥对煤热解特性的影响。煤和污泥的热解特性参数不同,主要表现在总失重率、失重速率及挥发分析出温度区间等。煤与污泥S1混合有助于增加样品的热解总失重率,提高失重速率;污泥S1与煤的挥发分析出区间部分重合,污泥灰中含的无机物对煤的热解起到催化效果;煤和S2污泥混合后热解反应过程中无明显相互作用;煤与城市污水污泥混合物的相互作用与样品特性和混合比例有关。     

Behaviour of inorganic constituents of municipal sewage sludge during fluidized-bed combustion

The fate of main heavy metals in municipal sewage sludge (As, Cd, Co, Cr, Cu, Hg, Mo, Ni, Pb, and Zn) was investigated using a fluidized-bed reactor. The behaviour of metals in the incinerator was explored by comparing metal contents in the two main ash streams: bottom (in-bed) ash and ash separated by a cyclone (cyclone-catch ash). All metals showed enrichment in the cyclone ash. The ash originating from sewage sludge is thermally quite stable consisting of quartz, hematite, spar(s), mica(s), apatite, and anhydrite. It does not soften nor becomes sticky and does not tend to agglomerate at temperatures up to 950°C.     

水热污泥与煤在混燃过程中的协同效应特性研究

以城市污泥衍生的水热污泥(SS-derived hydrochar)为对象,结合傅里叶红外光谱分析(FT-IR)、X射线荧光光谱分析(XRF)和X射线衍射分析(XRD)等对比研究了水热污泥与三种不同品阶煤(褐煤、烟煤和无烟煤)在有机/无机结构与燃料特性上的异同;同时,通过热重(TG)与偏差分析(Deviation)考察水热污泥与各阶煤在不同混合比例条件下的协同燃烧行为及其作用机制。结果表明,污泥经过水热处理后其有机结构和燃烧行为均提升至与煤相似的水平,该过程不仅改善污泥的燃烧特性,并增强其与煤之间的协同燃烧效应。水热污泥中适量的轻质组分与(碱)碱土金属能在混合燃烧过程中加速煤的失重速率,其对三种煤的促进作用可达4.4%-16.1%(褐煤)、1.9%-9.4%(烟煤)和4.8%-12.1%(无烟煤)。总体而言,水热污泥与褐煤混合而成的燃料在燃料性能上具有较大的优势,并且其混合比例以30%(水热污泥):70%(褐煤)与50%(水热污泥):50%(褐煤)为宜。     

TG-MS as a technique for a better monitoring of the pyrolysis,gasification and combustion of two kinds of sewage sludge

Sewage sludge disposal is a difficult task owing to increasingly restrictive re-use policies. Its final destination will obviously depend on its nature and composition but the generation of energy is a significant option. The thermochemical conversion requires exhaustive gas emission controls. In this regard, this paper offers the results of the use of mass spectrometry together with a thermogravimetric analysis system used to study the thermal conversion processes of two kinds of sewage sludge under different atmospheres simulating pyrolysis, gasification and combustion. This TG-MS combination indicates that gasification is the best process for one kind of sludge while a co-combustion process is more suitable for the other. This revised version was published online in July 2006 with corrections to the Cover Date.     

DTG-DTA study of sewage sludge used in the sorption of Cd2+ and Co2+

The present study was carried out for evaluating the retention behavior of sanitary sewage in relation to cadmium and cobalt ions in an ascendant continuous-flow reactor. It was found that the studied sludge presented a high assimilation of the metals, probably due to the presence of anionic groups, which favors adsorption and complexation processes. Thermal analyses of the samples showed a shift in the thermal decomposition of the ‘in natura’ sludge, when compared with those of the samples spiked with the metals, confirming the possibility of interactions between the heavy metals and the anionic groups present in the sludge.     

Development of the extraction method for the simultaneous determination of butyl-, phenyl- and octyltin compounds in sewage sludge

The toxicity and bioaccumulation of organotin compounds (OTCs) led to the development of sensitive and selective analytical methods for their determination. In the past much attention was assigned to the study of OTCs in biological samples, water and sediments, coming mostly from marine environment. Little information about OTCs pollution of terrestrial ecosystems is available. In order to optimise the extraction method for simultaneous determination of butyl-, phenyl- and octyltin compounds in sewage sludge five different extractants (tetramethylammonium hydroxide, HCl in methanol, glacial acetic acid, mixture of acetic acid and methanol (3:1), and mixture of acetic acid, methanol and water (1:1:1)), the presence or not of a complexing agent (tropolone), and the use of different modes of extraction (mechanical stirring, microwave and ultrasonic assisted extraction) were tested. Extracted OTCs were derivatised with sodium tetraethylborate and determined by gas chromatography coupled with mass spectrometer. Quantitative extraction of butyl-, phenyl- and octyltin compounds was obtained by the use of glacial acetic acid as extractant and mechanical stirring for 16 h or sonication for 30 min. The limits of detection and quantification for OTCs investigated in sewage sludge were in the ng Sn g⁻¹ range.     

Thermal decomposition study of sewage sludge and of organicwaste used in the sorption of metals

The conventional treatments of effluents containing heavy metals produce significant quantities of byproducts with recalcitrant characteristics, making necessary looking after alternative techniques in order to avoid the production of new contaminated residues. Sorption process of chromium and zinc in vertical columns loaded with sewage sludge and organic solid waste has been studied in this work. The data from the TG curves of the two sorbents presented significant differences when they were submitted to the metal uptake, being noticed the displacement of the thermal events towards lower temperatures for both types of sorbents studied. As it was expected, for both sorbents, an increase in the mass of samples has been observed at the completion of the thermal tests upon metal uptake. Therefore, these facts demonstrate that during the biosorption process a physico-chemical interaction took place between sorbents and metals, as it was evidenced by the more than 100 K increase in the decomposition temperatures as well as the variation of the ΔH values of the samples.