Optimisation of programmable temperature vaporizer-based large volume injection for determination of pesticide residues in fruits and vegetables using gas chromatography-mass spectrometry

The applicability of programmable temperature vaporizer (PTV) solvent vent injection to the gas chromatographic (GC) determination of pesticide residues in fruits and vegetables was evaluated with the aim of miniaturizing the current multiresidue method. For that purpose 24 pesticides representing different chemical classes were initially chosen for optimisation of the large volume injection (LVI) parameters. Various parameters related to the optimum injector performance were tested for several types of packed and empty liners using both fast (at-once) and speed-controlled PTV solvent vent injection of standard solutions in ethyl acetate. In the next step, several packed and empty liners were evaluated for their suitability for pesticide multiresidue analysis. Parameters identified as optimal were then applied for PTV solvent vent injection of sample extracts prepared using the miniaturized multiresidue method to assess the long-term stability of the system. The combined use of large volume injection of 10 microl ethyl acetate extract into an empty multi-baffled or a CarboFrit packed liner using PTV injectors and GC-MS analysis enabled the detection and quantification of 124 pesticides in fruit and vegetable samples at the 0.01 mg/kg level using miniaturized reversed-phase solid-phase extraction (RP-SPE) of diluted acetone extract and clean-up on a small anion-exchange SPE column.     

Influence of the injection technique and the column system on gas chromatographic determination of polybrominated diphenyl ethers

In this paper, we present an investigation of the influence of the gas chromatographic separation system on the determination of polybrominated diphenyl ethers (PBDEs). Capillary columns, retention gaps and press-fit connectors, as well as different injection techniques have been evaluated with respect to yield and repeatability. The split/splitless injection has been optimized and compared to on-column injection, the septum equipped temperature programmable injector (SPI) and the programmable temperature vaporizing (PTV) injector. Furthermore, a comparison of the different operational modes of the PTV injector is presented. The results show that there are large variations in the yield of PBDEs depending on the column and the injection systems. Especially the high molecular weight BDE congeners can be subject to severe discrimination. Unfavorable conditions can lead to a complete loss of nona and deca substituted BDE congeners.     

Capillary gas chromatography of tert-butyldimethlysilylamino acids with PTV injection

The programmable temperature vaporizing injector (PTV) has been used to study the effects of injection temperature and initial heating period on the FID response factors of TBDMS derivatives of 17 protein amino acids. The relative response factors were calculated for injection temperatures of 50°C, 90°C, 160°C, 220°C, and 260°C with different initial heating periods (1 s, 5 s, and 10 s) and the results compared with the values obtained for the calculated response factors obtained under classical split injection conditions (300°C, continuous). Except for expected peak broadening effects, the initial heating period does not seem to have significative effects on relative peak areas. The response to the derivatives of alanine, glycine, α-aminobutyric acid, valine, proline, methionine, cysteine, phenylalanine, asparagine, and arginine was only slightly affected by increasing the injection temperature whereas the response factors for the derivatives of serine, threonine, glutamic acid, lysine, histidine, tyrosine, and tryptophan were strongly dependent upon initial injection temperatures, decreasing rapidly at temperatures above 160°C. The cold split-splitless injection is clearly advantageous over the classical hot injection techniques for the analysis of this type of aminoacid derivative.     

Determination of dioxin-like polychlorinated biphenyls in 1 mL whole blood using programmable temperature vaporization large volume injection coupled to gas chromatogram and high-resolution mass spectrometry

A sensitive method based on programmable temperature vaporization large volume injection coupled to gas chromatogram and high-resolution mass spectrometry (PTV-GC–HRMS) has been developed for the determination of ultra trace levels of dioxin-like polychlorinated biphenyls (DL PCBs) in small amounts of human blood. Blood samples (1 mL) were first extracted by column extraction and then purified with column chromatorgraphies. Final extracts (20 μL) were introduced to the PTV injector under the solvent vent mode and detected by GC–HRMS (SIM mode). PTV parameters were observed by changing one factor at a time (practical conditions: vent flow: 50 mL min⁻¹, vent pressure: 0 kPa and vent time: 0.1 min), recoveries of most PCB congeners ranged from 55.1% to 108%, and method detection limits were in the range of 0.11–1.63 pg g⁻¹.     

Picogram determination of estrogens in water using large volume injection gas chromatography–mass spectrometry

In this study, a simple and efficient large volume injection gas chromatography–mass spectrometry (GC-MS) method, via a programmable-temperature vaporizer (PTV) inlet, has been developed and applied in the determination of estrogens in environmental water samples without a prior derivatization process. Three commonly used estrogens estrone, 17 β-estradiol and 17 α-ethynylestradiol were selected as target compounds for this study. It has been demonstrated that the type of gas chromatograph liner and the initial inlet temperature can greatly affect the response intensity of estrogens. Three different types of PTV liners have been studied; the multibaffle liner generated the strongest response intensities towards the estrogen analytes. The results showed that the response intensities of estrogens reduced sharply while the initial inlet temperature increased. Various instrument conditions and sample preparation methods were studied in detail. The optimized method has been validated with good linearity, precision and accuracy. The method detection limit of each estrogen was found to be 0.041 ng/L for estrone, 0.046 ng/L for 17 β-estradiol and 0.031 ng/L for 17 α-ethynylestradiol. To the best of our knowledge, these results represent the best sensitivities achieved for estrogens analyzed in water samples via traditional GC-MS method without a derivatization process. This method has been successfully applied in the analyses of different water samples.     

Optimization of large volume injection-programmable temperature vaporization-gas chromatography-mass spectrometry analysis for the determination of estrogenic compounds in environmental samples

Large volume injection-programmable temperature vaporization-gas chromatography-mass spectrometry (LVI-PTV-GC-MS) was optimized for the determination of estrone (E1), 17β-estradiol (E2), 17α-ethynyl estradiol (EE2), mestranol (MeEE2) and estriol (E3) for their determination in environmental samples (estuarine water, wastewater, fish bile and fish homogenate) after derivatization with 25 μL (BSTFA+1% TMCS) and 125 μL of pyridine. Experimental designs such as Plackett-Burman (PBD) and central composite designs (CCDs) were used to optimize the LVI-PTV variables (cryo-focusing temperature, vent time, vent flow, vent pressure, injection volume, purge flow to split vent, splitless time and injection speed). Optimized conditions were as follows: 45 μL of n-hexane extract are injected at 60°C and 6 μL/s with a vent flow and a vent pressure of 50 mL/min and 7.7 psi, respectively, during 5 min; then the split valve is closed for 1.5 min and afterwards the injector is cleaned at 100 mL/min before the next injection. The method was applied to the determination of estrogenic compounds in environmental samples such as estuarine water, wastewater, and fish homogenate and bile. Limits of detection (0.04-0.15 ng/L for water samples, 0.04-0.67 ng/g for fish bile and 0.1-7.5 ng for fish homogenate) obtained were approx. ten times lower than those obtained by means of a common split/splitless inlet.     

Optimisation and validation of programmed temperature vaporization (PTV) injection in solvent vent mode for the analysis of the 15 + 1 EU-priority PAHs by GC-MS

This paper presents the optimisation of a programmed temperature vaporization solvent vent (PTV-SV) injection gas chromatographic mass spectrometric (GC-MS) method for the analysis of the 15 + 1 EU-priority PAHs in food extracts. Three operation parameters (vent time, vent flow and vent pressure) were optimised by applying a D-optimal experimental design. Among these variables, vent time showed the highest effect on the analytical response (signal intensity) of the target PAHs.The 15 + 1 EU-priority PAHs were analysed in solvent solutions and in extracts of fortified sausage. In addition, blank lamb meat extracts were prepared and spiked with the target PAHs prior to GC-MS analysis. The performance of the optimised PTV-SV injection GC-MS method was scrutinised for linearity, precision, matrix effects and robustness. All parameters were found satisfactorily. Compared to PTV injection in splitless mode, the PTV-SV injection method provided an enhancement of sensitivity for all target PAHs. Especially significant was the improvement of the S/N ratios of the compounds with the highest molecular mass.     

大体积进样气质联用法测定浓缩果蔬汁中农药的残留量

建立了气相色谱-质谱同时检测果蔬汁中多类农药残留的方法。利用Agilent仪器的保留时间锁定功能（RTL）及相应的质谱农药库，建立了多类农药选择离子监测的分组时间窗，避免了仪器维护后农药保留时间烦琐的更新过程，保证了农药保留时间的重复性；探讨了具有溶剂排空模式的程序升温蒸发（PTV）对大体积进样的作用。通过对分流排空量、吹扫时间、PTV温度及其进样体积等PTV参数的优化，提高了检测灵敏度。通过同位素标汜农药作为内标，GC—MS的定量可靠性得到改善。     

Use of experimental design in the optimisation of stir bar sorptive extraction followed by thermal desorption for the determination of brominated flame retardants in water samples

A method for the determination of polybrominated diphenyl ethers (PBDEs) and polybrominated biphenyls (PBBs) in water samples is proposed. The method involving stir bar sorptive extraction (SBSE) and thermal desorption followed by gas chromatography coupled with mass spectrometry was optimised using statistical design of experiments. In the first place, the influence of different polydimethylsiloxane stir bars was studied. A Plackett–Burman design was chosen to estimate the influence of five factors on the efficiency of the SBSE process: desorption time (5–10 min), desorption temperature (250–300 °C), desorption flow (50–100 mL min⁻¹), cryofocusing temperature (-130 to 40 °C) and vent pressure (0–12.8 psi). Afterwards, two central composite designs were used to find the optimal process settings that were applied to the optimisation of both desorption and extraction efficiency. In the case of the desorption parameters, long desorption times (10 min) and desorption flows lower than 70 mL min^-1 yielded the best signals for the majority of compounds. However, different behaviour among the analytes was observed for the vent pressure and we decided to fix it at an intermediate value (7 psi). In the case of extraction parameters, the sample volume and the addition of NaCl did not have a significant effect, while the addition of methanol yielded better extraction responses. Remarkable recovery (82–106%) and repeatability (less than 18%) were attained. Furthermore, excellent regression coefficients (r ² = 0.991–0.999) and low detection limits (1.1–6.0 ng L⁻¹) were also achieved for the congeners studied. The proposed method was applied to the analyses of PBDEs and PBBs in waters from the Basque Country, Spain.     

碳纳米管顶空固相微萃取测定水中的多溴联苯醚

建立了顶空固相微萃取联结气相色谱-电子捕获检测器（HS-SPME-GC-ECD）测定水中多溴联苯醚的方法。制作了多壁碳纳米管涂层固相微萃取探头。优化了萃取时间,萃取温度,搅拌速度,顶空体积,溶液的pH,离子强度及有机溶剂等影响萃取效率的各种因素。比较了室温和100 ℃顶空萃取和直接萃取的效率。结果表明,室温下直接萃取比顶空萃取的效率高2-4倍,而在100 ℃时顶空萃取比直接萃取的效率高1-8倍。除BDE-154外,无论直接萃取还是顶空萃取,100 ℃时的萃取效率均高于室温。方法的线性范围50-1600 ng/L,相关系数为0.995-0.998,5种多溴联苯醚的最低检出限（S/N=3）为1.14-16.25 ng/L,相对标准偏差（RSD%,n=5）小于10%。本方法用于真实水样的测定,回收率为74.2%-98.7%。     

Rapid simultaneous determination of multiple pesticide residues in traditional Chinese medicines using programmed temperature vaporizer injection-fast gas chromatography coupled with mass spectrometry

A fast gas chromatography coupled with mass spectrometry (GC-MS) using large volume injection with programmed temperature vaporizer in solvent vent mode (PTV-LVI-SV) was developed for the trace determination of multiple pesticide residues in traditional Chinese medicines (TCMs). Experimental conditions of PTV-LVI-SV injection were optimized by central composite design. The optimized result was that initial temperature was held at 40°C for 39 s, vent flow rate was set at 45 mL/min and vent pressure was held at 0 psi for 36 s, injection volume was 10 μL. Furthermore, the quick and effective QuEChERS (quick, easy, cheap, effective, rugged and safe) method was performed to extract and purify pesticide residues in TCMs. The prepared samples were analyzed with GC-MS in the selected ion monitoring mode (SIM). The lowest LOD was 4 μg/kg for some pesticides. The recoveries were checked by spiking samples with pesticides at 25, 50 and 250 μg/kg. The average recoveries of most pesticides were from 80 to 118%. The result indicated that QuEChERS and PTV-LVI-SV GC-MS method was a rapid and sensitive analysis technique for the determination of multiple pesticide residues in TCMs.     

Temperature-Programmed Packed Capillary Liquid Chromatography Separation with Large Volume On-Column Focusing of Retinyl Esters

A non-aqueous isocratic reversed-phase packed capillary high performance liquid chromatography method for the determination of retinyl esters, utilizing temperature programming and on-column focusing large volume injection, has been developed. The stationary phase material was C₃₀, and the mobile phase consisted of acetonitrile-dichloromethane (70 : 30, v/v). A three-step temperature program, starting at 10°C for 10 min, then 1°/min to 30°C, and finally 2.5°/min to 70°C, was found most appropriate. Compared to an isothermal separation at 25°C, this temperature program provided improved peak resolution, enhanced peak shapes of the last eluting compounds, and a reduction of the overall elution time. A mass limit of detection of 27 pg was found with respect to retinyl palmitate, using UV detection with an “U” shaped flow cell at 327 nm. This corresponds to a concentration limit of detection of 2.7 pg/μL, when utilizing an injection volume of 10 μL. The concentration of retinyl palmitate in arctic seal liver samples was estimated to be 62.6 μg/g liver.     

Determination of curcumol in rat plasma by capillary gas chromatography with a hydrogen flame ionization detector

A simple and sensitive capillary gas chromatography with a hydrogen flame ionization detector (GC‐FID) method was developed for the determination of curcumol in rat plasma. From a variety of compounds and solvents tested, buagafuran was selected as the internal standard (IS) and acetonitrile was found to be the best protein precipitation agent and solvent for extracting curcumol from plasma and tissues samples. (Buagafuran was used as an internal standard. Curcumol was extracted by a protein precipitation with acetonitrile.) The samples were determined by GC on an HP‐5 column (30.0 m × 0.32 mm, 0.25 μm); inlet volume 2 μL; split ratio 10 : 1; inlet temperature 250°C; oven temperature 180°C; flow 1.0 mL/·min; FID 250°C; carrier gas N₂. The resulting retention times of curcumol and IS were 6.0 and 9.5 min. There was good linearity over the range 0.133–133.3 μg/mL (r = 0.9999) in plasma samples. The method recoveries were 97.7–102.0% in plasma, and the intra‐ and inter‐day variances (RSD) were less than 15% in all cases. The GC method was applied to develop a pharmacokinetics study in which experimental rats received a single administration of curcumol by intravenous injection. Copyright © 2009 John Wiley & Sons, Ltd.     

Kinetics of thiophene hydrodesulfurization over a supported Mo–Co–Ni catalyst

In this study, the kinetics of thiophene (TH) hydrodesulfurization (HDS) over the Mo–Co–Ni-supported catalyst was investigated. Trimetallic catalyst was synthesized by pore volume impregnation and the metal loadings were 11.5 wt % Mo, 2 wt % Co, and 2 wt % Ni. A large surface area of 243 m²/g and a relatively large pore volume of 0.34 cm³/g for the fresh Mo–Co–Ni-supported catalyst indicate a good accessibility to the catalytic centers for the HDS reaction. The acid strength distribution of the fresh and spent catalysts, as well as for the support, was determined by thermal desorption of diethylamine (DEA) with increase in temperature from 20 to 600 °C. The weak acid centers are obtained within a temperature range between 160 and 300 °C, followed by medium acid sites up to 440 °C. The strong acid centers are revealed above 440 °C. We found a higher content of weak acid centers for fresh and spent catalysts as well as alumina as compared to medium and strong acid sites. The catalyst stability in terms of conversion as a function of time on stream in a fixed bed flow reactor was examined and almost no loss in the catalyst activity was observed. Consequently, this fact demonstrated superior activity of the Mo–Co–Ni-based catalyst for TH HDS. The activity tests by varying the temperature from 200 to 275 °C and pressure from 30 to 60 bar with various space velocities of 1–4 h^?1 were investigated. A Langmuir–Hinshelwood model was used to analyze the kinetic data and to derive activation energy and adsorption parameters for TH HDS. The effect of temperature, pressure, and liquid hourly space velocity on the TH HDS activity was studied.     

Thermal degradation observed with different injection techniques: Quantitative estimation by the use of thermolabile carbamate pesticides

An experiment has been designed to study the thermal degradation of thermolabile compounds caused by various injection techniques. The four carbamate pesticides aminocarb, bendiocarb, carbaryl, and dioxacarb decompose thermally into methylisocyanate and the corresponding phenol. The carbamets and the phenols arising from them were separated on a 25 m SE-54 fused silica column; all compounds exhibited sharp peak shape indicating that the degradation observed took place completely within the injector. When cold on-column injection was employed no thermal degradation was observed whereas with hot splitless injection at 220°C decomposition of the carbamates was almost complete. PTV injection was found to produce intermediate results. When packed with glass wool and operated with glass wool and operated with starting temperatures lower than the boiling point of the solvent, decomposition was found to be almost complete. Applying isothermal conditions at 140°C (30°C above the boiling point of toluene) aminocarb and bendiocarb underwent only slight decomposition while carbaryl and dioxacarb were about half degraded. Results from PTV injection with an empty insert resembled those obtained using cold on-column injection and in this mode the application of temperatures up to 200°C resulted in no visible degradation. This can be explained by the short residence time of the sample in the injector.     

程序升温大体积进样气相色谱-负化学离子源质谱法测定白菜和苹果中103种农药残留

采用程序升温大体积进样(PTV-LVI)和负化学离子源(NCI)技术建立了白菜和苹果中103种农药残留分析的气相色谱-质谱检测方法。PTV-LVI参数优化为: 初始温度45 ℃、分流排空流量20 mL/min、吹扫时间1 min和溶剂挥发温度60 ℃。样品采用QuEChERS方法进行快速处理,在NCI方式下进样10 μL,用基质标准溶液进行定量,结果表明103种农药的方法检出限均低于5 μg/kg。在5 μg/kg和10 μg/kg添加水平下,白菜和苹果中农药的平均回收率为58.5%～113.2%,相对标准偏差为3.3%～14.5%。该方法样品处理简单快速,相比普通分流/不分流进样和电子轰击电离气相色谱-质谱法,其灵敏度和选择性明显提高,适用于日常检测工作。     

两种轻烃分析方法(“PTV切割反吹”和“顶空”)的对比研究

 建立了“程序升温蒸发进样器 (PTV)切割反吹”和“顶空”两种有关原油中轻烃的分析方法 ,色谱柱的使用寿命长、分析周期短 ,原油中 < ,将原油直接注入汽化室所得的分析数据较可靠 ,并对引起误差的原因进行了探讨。指出用这两种方法所获得的数据是不能合在一起作地化研究的 ) % 5 2 1%～ ( 19个地化参数的相对误差范围约为± 10个油样用两种分析方法所得 6个油区的 ,还报道了采自我国 ,并有良好的重复性。。     

Residue Analysis and Determination of IMI Herbicides in Sunflower and Soil by GC–MS

Sunflower agriculture is an important subsector that plays a key role in the economy of Turkey, contributing 1.38 million tonnes. The aim of this study is to investigate the levels of imidazolinone (IMI) group herbicides in Thrace Region, Turkey. In particular, we aimed to determine the residue levels of imazamox, a herbicide used in sunflower production in Thrace Region, in soil, different parts of plant, and seed. Five herbicides were identified in sunflower samples using solid–liquid extraction with gas chromatography–electrospray ionization mass spectrometry (GC–EI–MS) on single-quadruple instruments in selected ion monitoring (SIM) mode. The optimized conditions were found to be mobile-phase flow rate of 1 mL min^?1 and injection volume of 3 μL in programmed temperature vaporization (PTV) solvent vent mode. The recovery of imazamox, imazaquin, imazethapyr, imazapyr, and imazapic from sunflower plant and soil was 89 and 99, 104 and 105, 92 and 93, 96 and 92, and 99 and 96%, respectively.     

Thermogravimetric analysis of cellulose insulation and determination of activation energy of its thermo‐oxidation using non‐isothermal,model‐free methods

The aim of the work was to determine the effect of heating rate on initial decomposition temperature and phases of thermal decomposition of cellulose insulation. The activation energy of thermo‐oxidation of insulation was also determined. Individual samples were heated in the air flow in the thermal range of 100°C to 500°C at rates from 1.9°C min^?1 to 20.1°C min^?1. The initial temperatures of thermal decomposition ranged from 220°C to 320°C, depending on the heating rate. Three regions of thermal decomposition were observed. The maximum rates of mass loss were measured at the temperatures between 288°C and 362°C. The activation energies, which achieved average values between 75 and 80.7 kJ mol^?1, were calculated from the obtained results by non‐isothermal, model‐free methods. Copyright © 2014 John Wiley & Sons, Ltd.     

The growth of shear bands in polystyrene

Shear-band growth velocities have been determined as a function of stress and temperature in polystyrene. The results demonstrate that shear bands can propagate under isothermal conditions; an adiabatic temperature rise at the shear band tip is not necessary for continued localization and growth of the band. The velocity is stress activated with a shear activation volume of 4600 ų and thermally activated with an activation enthalpy of 2.8 eV. Comparison of these values of the activation parameters with those for bulk shear flow in polystyrene indicates that the shear band propagation is controlled by the plastic strain rate of the glassy polymer immediately ahead of the tip of the band. Argon's molecular kink model of the elemental deformation process is consistent with measured values of the activation parameters whereas Bowden and Raha's dislocation model is not. The shear bands grow at an angle of ca. 38° to the axis of compression, and if the direction of compression is altered, the shear bands will change direction so as to maintain the 38° angle. Current explanations can not quantitatively account for the large deviation of the shear bands from the 45° plane of maximum shear stress.