Ammonia Gas Sensor Using Polypyrrole‐Coated TiO2/ZnO Nanofibers

Highly porous polypyrrole (PPy)‐coated TiO₂/ZnO nanofibrous mat has been successfully synthesized. The core TiO₂/ZnO nanofibers have an average diameter of ca. 100 nm and the shell of ultrathin PPy layer has a thickness of ca. 7 nm. The NH₃ gas sensor using the as‐prepared material exhibited a fast response over a wide dynamic range and high sensitivity with a detection limit of 60 ppb (S/N=3). Compared to conventional pristine PPy film, the improved performance in NH₃ detection can be attributed to the free access of NH₃ to PPy and a minimized gas diffusion resistance through the ultrathin PPy layer.     

Flexible NH3 sensors fabricated by in situ self-assembly of polypyrrole

Novel flexible NH₃ gas sensors were formed by the in situ self-assembly of polypyrrole (PPy) on plastic substrates. A negatively charged substrate was prepared by the formation of an organic monolayer (3-mercapto-1-propanesulfonic acid sodium salt—MPS) on a polyester (PET) substrate using a pair of comb-like Au electrodes. Two-cycle poly(4-styrenesulfonic acid) sodium salt/poly(allylamine hydrochloride) (PSS/PAH) bilayers (precursor layer) were then layer-by-layer (LBL) deposited on an MPS-modified substrate. Finally, a monolayer of PPy self-assembled in situ and PPy multilayer thin films self-assembled LBL in situ on a (PSS/PAH)₂/MPS/Au/Cr/PET substrate. The thin films were analyzed by atomic force microscopy (AFM). The effects of the precursor layer (PSS), the deposition time of the monolayer of PPy and the number of PPy multilayers on the gas sensing properties (response) and the flexibility of the sensors were investigated to optimize the fabrication of the film. Additionally, other sensing properties such as sensing linearity, reproducibility, response and recovery times, as well as cross-sensitivity effects were studied. The flexible NH₃ gas sensor exhibited a strong response that was comparable to or even greater than that of sensors that were fabricated on rigid substrate at room temperature.     

Electrochemical sensor for acetaminophen based on an imprinted TiO2 thin film prepared by liquid phase deposition

An electrochemical sensor based on a molecularly imprinted TiO₂ thin film is proposed for the determination of acetaminophen. The imprinted TiO₂ films were obtained by liquid phase deposition (LPD) in the presence of acetaminophen, the functional monomer and the aqueous solution of (NH₄)₂TiF₆ and H₃BO₃. The results show that acetaminophen is embedded into the imprinted film in the presence of p-tert-butylcalix[6]arene as a functional monomer, and can be removed completely by washing with ethanol. The surface morphology, spectral properties and electrochemical characterizations of the imprinted sensor were investigated in detail. The combination of molecularly imprinted and LPD technique was shown to be a general strategy for constructing a molecular recognition system.     

聚甲基丙烯酸甲酯包覆(CH3NH3)PbBr3纳米晶静电纺丝膜的制备及对氨气的荧光传感

采用原位合成法制备了聚甲基丙烯酸甲酯包覆MAPbBr₃纳米晶(MAPbBr₃@PMMA,MA=甲铵离子)静电纺丝膜。当氨气(NH₃)通入MAPbBr₃@PMMA纤维膜时与MAPbBr₃中的MA发生取代,能显著降低MAPbBr₃@PMMA纤维的荧光强度,以此构建了基于MAPbBr₃@PMMA纤维荧光猝灭的NH₃传感器。通过扫描电镜、透射电镜、粉末X射线衍射和红外对静电纺丝膜的形貌和结构进行表征,通过紫外可见光谱、荧光光谱对其光学特性进行表征。结果表明,传感器的荧光强度与NH₃浓度在8~90 mg·L^-1之间呈现出良好的线性关系(r=0.995 9),NH₃的检出限低(3 mg·L^-1),且具有良好的重现性和选择性。在实际样品气体的测定中,加标回收率为92.2%~102.1%,相对标准偏差(RSD)为1.8%~3.2%。     

聚甲基丙烯酸甲酯包覆(CH3NH3) PbBr3纳米晶静电纺丝膜的制备及对氨气的荧光传感

采用原位合成法制备了聚甲基丙烯酸甲酯包覆MAPbBr₃纳米晶（MAPbBr₃@PMMA,MA=甲铵离子）静电纺丝膜。当氨气（NH₃）通入MAPbBr₃@PMMA纤维膜时与MAPbBr₃中的MA发生取代,能显著降低MAPbBr₃@PMMA纤维的荧光强度,以此构建了基于MAPbBr₃@PMMA纤维荧光猝灭的NH₃传感器。通过扫描电镜、透射电镜、粉末X射线衍射和红外对静电纺丝膜的形貌和结构进行表征,通过紫外可见光谱、荧光光谱对其光学特性进行表征。结果表明,传感器的荧光强度与NH₃浓度在8~90 mg·L^-1之间呈现出良好的线性关系（r=0.995 9）,NH₃的检出限低（3 mg·L^-1）,且具有良好的重现性和选择性。在实际样品气体的测定中,加标回收率为92.2%~102.1%,相对标准偏差（RSD）为1.8%~3.2%。     

Two-Dimensional Sol-Gel Synthesis of Ultrathin Zirconia and Hetero-Layered Titania/Zirconia Films

Synthesis of ZrO₂ and hetero-layered TiO₂/ZrO₂ ultrathin films was investigated by two-dimensional sol-gel process assisted by n-octadecylacetoacetate (C₁₈AA). When a hexane solution of tetrabutoxyzirconium (TBZ) and C₁₈AA was spread on the water surface, Zr-based gel films stabilized with C₁₈AA were formed at the air/water interface. After deposition on substrates, the gel films were successfully transformed into ZrO₂ ultrathin films by heating at 773 K for 0.5 h, the thickness of which was controllable on the order of sub-nanometer level by the number of gel-layer deposition and the molar ratio of [TBZ]/[C₁₈AA]. Well-organized hetero-multilayers composed of ultrathin TiO₂ and ZrO₂ layers could be fabricated by the alternate deposition of C₁₈AA-stabilized Ti- and Zr-gel films.     

Application of principal component analysis to gas sensing characteristics of Cr0.8Fe0.2NbO4 thick film array

The transient changes in resistances of Cr_0.8Fe_0.2NbO₄ thick film sensors towards specified concentrations of H₂, NH₃, acetonitrile, acetone, alcohol, cyclohexane and petroleum gas at different operating temperatures were recorded. The analyte-specific characteristics such as slopes of the response and retrace curves, area under the curve and sensitivity deduced from the transient curve of the respective analyte gas have been used to construct a data matrix. Principal component analysis (PCA) was applied to this data and the score plot was obtained. Distinguishing one reducing gas from the other is demonstrated based on this approach, which otherwise is not possible by measuring relative changes in conductivity. This methodology is extended for three Cr_0.8Fe_0.2NbO₄ thick film sensor array operated at different temperatures.     

Carbon nanotube networks as gas sensors for NO2 detection

Networks of different carbon nanotube (CNT) materials were investigated as resistive gas sensors for NO₂ detection. Sensor films were fabricated by airbrushing dispersions of double-walled and multi-walled CNTs (DWNTs and MWNTs, respectively) on alumina substrates. Sensors were characterized by resistance measurements from 25 to 250 °C in air atmosphere in order to find the optimum detection temperature. Our results indicate that CNT networks were sensitive to NO₂ concentrations as low as 0.1 ppm. All tested sensors provided significantly lower response to interfering gases such as H₂, NH₃, toluene and octane. We demonstrate that the measured sensitivity upon exposure to NO₂ strongly depends on the employed CNT material. The highest sensitivity values were obtained at temperatures ranging between 100 and 200 °C. The best sensor performance, in terms of recovery time, was however achieved at 250 °C. Issues related to the gas detection mechanisms, as well as to CNT network thermal stability in detection experiments performed in air at high operation temperatures are also discussed.     

The influence of film thickness and process temperature on <Emphasis Type="Italic">c</Emphasis>-axis orientation of Bi<Subscript>3</Subscript>TiTaO<Subscript>9</Subscript> thin films

Bi-layered ferroelectric Bi₃TiTaO₉ (BTT) thin films with different thickness (ranging from 100 to 400 nm) were successfully fabricated on Pt(111)/TiO₂/SiO₂/(100)Si substrates using chemical solution deposition (CSD) technique at different annealing temperatures. The c-axis orientation of the films was affected by film thickness and process temperature. The thinner the film and the higher the process temperature, the higher the c-axis orientation. With the increase of film thickness, the stress decreased but the film roughness increased, which led to the decrease of c-axis orientation of films. BTT films annealed at 800°C were found to have much improved remament polarization (P _r ) than that of films annealed at 650 and 750°C. The P _r and coercive field (E _c ) values were measured to be 2 μC/cm² and 100 kV/cm, respectively. BTT films showed well-defined ferroelectric properties with grain size larger than 100 nm.     

Preparation of TiO2 nanocrystalline films controlled by acetylacetone/polyethylene glycol and their photoelectric properties

TiO₂ nanocrystalline films were prepared from titanium tetra-n-butoxide modified with double hydrolysis inhibitors, acetylacetone and polyethylene glycol (PEG), in mixture of methanol and ethanol. The correlation among surface structure of the TiO₂ films, preparation conditions, and photovoltaic properties of the solar cells using the TiO₂ films was investigated. The particle size of the obtained TiO₂ films was decreased as the PEG content increased. The nanostructured films with the narrow distribution of particle size could be prepared. The amounts of adsorbed dyes for these TiO₂ films were larger than that without PEG. The performance of the solar cell fabricated using the TiO₂ film improved as the amount of the PEG increased, and the solar cell using the TiO₂ film prepared from the solution with 30 wt% PEG exhibited the highest performance.     

Preparation of Titanium Oxide Layer on Silica Glass Substrate with Titanium Naphthenate Precursor

Nanocrystalline TiO₂ thin films on silica glass substrates were prepared by using a naphthenic acid precursor. As-deposited thin films were heat treated at 500, 600, 700 and 800^∘C for 30 min in air. The TiO₂ thin films were analyzed by High Resolution X-ray diffraction, ultra violet—visible—near infrared spectrophotometer, field emission—scanning electron microscope and scanning probe microscope. After annealing at 600 and 700^∘C, the XRD patterns consist of only anatase peaks of TiO₂ film. Rutile(110) peak begins to appear at an annealing temperature of 800^∘C. Relative high transmittance at visible range was obtained for all films except the film annealed at 800^∘C. Optical band gap, E_g, is in the range between 3.53 and 3.78 eV except the TiO₂ film annealed at 500^∘C. The best hydrophilicity was achieved with a high-temperature annealing.     

Chemical solution processing and characterization of Ba(Zr,Ti)O<Subscript>3</Subscript>/LaNiO<Subscript>3</Subscript> layered thin films

Ba(Zr,Ti)O₃/LaNiO₃ layered thin films have been synthesized by chemical solution deposition (CSD) using metal-organic precursor solutions. Ba(Zr,Ti)O₃ thin films with smooth surface morphology and excellent dielectric properties were prepared on Pt/TiO _x /SiO₂/Si substrates by controlling the Zr/Ti ratios in Ba(Zr,Ti)O₃. Chemically derived LaNiO₃ thin films crystallized into the perovskite single phase and their conductivity was sufficiently high as a thin-film electrode. Ba(Zr,Ti)O₃/LaNiO₃ layered thin films of single phase perovskite were fabricated on SiO₂/Si and fused silica substrates. The dielectric constant of a Ba(Zr_0.2Ti_0.8)O₃ thin film prepared at 700°C on a LaNiO₃/fused silica substrate was found to be approximately 830 with a dielectric loss of 5% at 1 kHz and room temperature. Although the Ba(Zr_0.2Ti_0.8)O₃ thin film on the LaNiO₃/fused silica substrate showed a smaller dielectric constant than the Ba(Zr_0.2Ti_0.8)O₃ thin film on Pt/TiO _x /SiO₂/Si, small temperature dependence of dielectric constant was achieved over a wide temperature range. Furthermore, the fabrication of the Ba(Zr,Ti)O₃/LaNiO₃ films in alternate thin layers similar to a multilayer capacitor structure was performed by the same solution deposition process.     

High photocatalytic activity and stability for decomposition of gaseous acetaldehyde on TiO2/Al2O3 composite films coated on foam nickel substrates by sol-gel processes

A set of anatase titanium dioxide (TiO₂) films coated on foam nickel that modified by Al₂O₃ films as transition layer (indicated as TiO₂/Al₂O₃ films) were synthesized via sol-gel route. The bulk and surface properties of the TiO₂/Al₂O₃ films were characterized by thermal gravimetric and differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), field-emission scanning electron microscope (FE-SEM), and BET. The photocatalytic activities of TiO₂/Al₂O₃ films were investigated based on the degradation of gaseous acetaldehyde under ultraviolet (UV) irradiation. The foam nickel is a promising substrate material in practical applications because of its excellent hydrodynamic properties for gas passing. The TiO₂/Al₂O₃ composite films showed much higher photocatalytic activity and stability for degradation of gaseous acetaldehyde than the onefold TiO₂ films. The significant enhancement in photocatalytic activity and stability can be ascribed to the coating of Al₂O₃ transition layer, which concentrates the target substances around TiO₂ particles and increases the specific surface area (SSA) of the substrate (the SSAs of bare foam nickel and Al₂O₃ modified foam nickel are 0.12 and 113.7 m²/g, respectively) to provide more sites for TiO₂ loading.     

Photo-Induced Hydrophilicity of TiO<Subscript>2</Subscript> Films Deposited on Stainless Steel via Sol-Gel Technique

The photo-induced hydrophilicity of TiO₂ films deposited on stainless steel substrates and silicon wafers using two different sol-gel routes has been investigated. The results indicate that crystalline titanium oxide films with excellent hydrophilic properties can be obtained on silicon wafer with both routes. XPS and XRD data reveal that films deposited on stainless steel exhibit crystallization features similar to those of films deposited on silicon wafers, and only differ by their oxidation degree owing to a TiO₂ reduction process associated to a diffusion of iron ions during deposition of the acidic sol and/or high temperature post-treatment. Consequently, hydrophilic properties of films deposited on stainless steel are inhibited. The deposition of a SiO_x barrier layer at the film/substrate interface allows preventing such a detrimental substrate influence. A low temperature deposition route of the TiO₂ film associated to the presence of a barrier layer yields best results in preventing iron contamination of the films.     

Comparison of CO2 Reduction Performance with NH3 and H2O between Cu/TiO2 and Pd/TiO2

The aim of this study is to clarify the effect of doped metal type on CO₂ reduction characteristics of TiO₂ with NH₃ and H₂O. Cu and Pd have been selected as dopants for TiO₂. In addition, the impact of molar ratio of CO₂ to reductants NH₃ and H₂O has been investigated. A TiO₂ photocatalyst was prepared by a sol-gel and dip-coating process, and then doped with Cu or Pd fine particles by using the pulse arc plasma gun method. The prepared Cu/TiO₂ film and Pd/TiO₂ film were characterized by SEM, EPMA, TEM, STEM, EDX, EDS and EELS. This study also has investigated the performance of CO₂ reduction under the illumination condition of Xe lamp with or without ultraviolet (UV) light. As a result, it is revealed that the CO₂ reduction performance with Cu/TiO₂ under the illumination condition of Xe lamp with UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:1:1 while that without UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:0.5:0.5. It is revealed that the CO₂ reduction performance of Pd/TiO₂ is the highest for the molar ratio of CO₂/NH₃/H₂O = 1:1:1 no matter the used Xe lamp was with or without UV light. The molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp with UV light was 10.2 μmol/g, while that for Pd/TiO₂ was 5.5 μmol/g. Meanwhile, the molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp without UV light was 2.5 μmol/g, while that for Pd/TiO₂ was 3.5 μmol/g. This study has concluded that Cu/TiO₂ is superior to Pd/TiO₂ from the viewpoint of the molar quantity of CO per unit weight of photocatalyst as well as the quantum efficiency.     

Preparation and Characterization of Bismuth Doped TiO2 Thin Films

A series of Bismuth-doped titanium oxide (Bi-doped TiO₂) thin films on glass substrates have been prepared by sol-gel dip coating process. The prepared catalysts were characterized by XRD and XPS. The photocatlytic activity of the thin film catalysts was evaluated through the photodegradation of aqueous methyl orange under UV illumination. The experiments demonstrated that the Bi-doped TiO₂ prepared was anatase phase. The doped bismuth was in the 3⁺ oxidation state. The presence of Bi significantly enhanced the photocatalytic activity of TiO₂ films. At calcination temperature of 500°C, with doping concentration of 2 wt %, Bi-doped TiO₂ thin film showed the highest photocatalyic activity.     

Patterning Effect of a Sol-Gel TiO2 Overlayer on the Photocatalytic Activity of a TiO2/SnO2 Bilayer-Type Photocatalyst

TiO₂ films with a thickness of 75 ± 5 nm (anatase) were formed on SnO₂-film (580 ± 80 nm) coated soda-lime glass substrates (SnO₂/SL-glass) by a sol-gel method. Although the photocatalytic activity for CH₃CHO oxidation (_ex > 300 nm) significantly exceeded that of a standard TiO₂/quartz sample, it decayed with illumination time (t) at t > 0.75 h. Stripes of anatase TiO₂ films of 40 nm in thickness and 1 mm in width were prepared on the SnO₂/SL-glass substrate in a 1-mm pitch by photolysis of an organically modified sol-gel film. The TiO₂ patterning further increased the photocatalytic activity by a factor of 4.1 as compared to the non-patterned sample, and it was also maintained at 0 < t < 2 h. The flat band potentials of the TiO₂ and SnO₂ films are determined to be –0.34 and +0.07 V (vs. SHE), respectively, at pH = 7 by the Mott-Schottky plots. On the basis of the results, the outstanding patterning effects could be rationalized in terms of the vectorial charge separation at the interface between TiO₂ and SnO₂.     

Bi2S3量子点敏化TiO2纳米阵列结构的制备及光电性能

利用水热法制备一维TiO₂纳米棒阵列,并采用化学浴沉积法(CBD)结合自组装技术在TiO₂纳米棒上敏化Bi₂S₃量子点,形成TiO₂/Bi₂S₃复合纳米棒阵列。系统研究了复合结构的表面形貌、晶体结构、光学及光电性能。结果表明:在修饰有三氨丙基三乙氧基硅烷自组装单分子膜(APTS-SAMs)的TiO₂纳米棒表面形成一层致密的Bi₂S₃量子点敏化层,这一技术的关键是含-NH₂末端的APTS-SAMs可有效促进Bi₂S₃的异相成核作用;Bi₂S₃的沉积时间对复合结构的光吸收及光电响应性能有决定性的影响,薄膜的光电流随着沉积时间呈先增加后减小的趋势,在沉积时间为20min时,光电流密度最大。这是因为随着沉积时间的增加,TiO₂纳米棒表面Bi₂S₃量子点密度增大,光吸收增加;而当沉积时间进一步延长时,Bi₂S₃在TiO₂纳米棒表面的大量负载而形成堆积和团聚,导致表面缺陷增多,光生电子复合几率增大,从而使光电流密度减小。     

Bi2S3量子点敏化TiO2纳米阵列结构的制备及光电性能研究

利用水热法制备一维TiO₂纳米棒阵列,并采用化学浴沉积法(CBD)结合自组装技术在TiO₂纳米棒上敏化Bi₂S₃量子点,形成TiO₂/Bi₂S₃复合纳米棒阵列.系统研究了复合结构的表面形貌、晶体结构、光学及光电性能.结果表明:在修饰有三氨丙基三乙氧基硅烷自组装单分子膜(APTS-SAMs)的TiO₂纳米棒表面形成一层致密的Bi₂S₃量子点敏化层,这一技术的关键是含-NH₂末端的APTS-SAMs可有效促进Bi₂S₃的异相成核作用;Bi₂S₃的沉积时间对复合结构的光吸收及光电响应性能有决定性的影响,薄膜的光电流随着沉积时间呈先增加后减小的趋势,在沉积时间为20 min时,光电流密度最大.这是因为随着沉积时间的增加,TiO₂纳米棒表面Bi₂S₃量子点密度增大,光吸收增加;而当沉积时间进一步延长时,Bi₂S₃在TiO₂纳米棒表面的大量负载而形成堆积和团聚,导致表面缺陷增多,光生电子复合几率增大,从而使光电流密度减小.     

Studies on photocatalytic activity of Ag/TiO2 films

Ag/TiO₂ photocatalytic films were produced by hybrid sol-gel method. The photocatalytic degradation of methyl orange (MO) in aqueous solution under 365 nm irradiation on TiO₂ and Ag/TiO₂ thin films was investigated. The state and amount of Ag species within the film and the enhancement mechanism of photocatalytic activity of Ag/TiO₂ were discussed. With a loading molar ratio of Ag/Ti = 0.135 in TiO₂ film, the maximum catalytic efficiency was observed. __________ Translated from Journal of Beijing Normal University (Natural Sciences), 2005, 41(6) (in Chinese)