Direct As,Bi, Ge,Hg and Se(IV) cold vapor/hydride generation from coal fly ash slurry samples and determination by electrothermal atomic absorption spectrometry

Direct cold vapor and hydride generation procedures for As, Bi, Ge, Hg and Se(IV) from aqueous slurry of coal fly ash samples have been developed by using a batch mode generation system. Ir-treated graphite tubes have been used as a preconcentration and atomization medium of the vapors generated. A Plackett–Burman experimental design has been used as a strategy for evaluation of the effects of several parameters affecting the vapor generation efficiency from solid particles, vapor trapping and atomization efficiency from Ir-treated graphite tubes. The effects of parameters such as hydrochloric acid and sodium tetrahydroborate, argon flow rate, trapping and atomization temperatures, trapping time, acid solution volume and mean particle size have been investigated. The significant parameters obtained (trapping and atomization temperatures for As and Ge; trapping temperature and trapping time for Bi; argon flow rate and atomization temperature for Se) have been optimized by 2²+star central composite design. For Hg, the trapping temperature has been also significant. Optimum values of the parameters have been selected for the development of direct cold vapor/hydride generation methods from slurry particles. The accuracy of methods have been verified by using NIST-1633a coal fly ash certified reference material. Absolute detection limits of 11.5, 48.0, 600, 55.0 and 11.0 ng l⁻¹ for As, Bi, Ge, Hg and Se have been achieved, respectively. A particle size less than 50 μm has shown to be adequate to obtain total cold vapor/hydride generation of metals content in the aqueous slurry particles.     

共价氢化物与汞离子反应的研究 Ⅰ 痕量锑高灵敏度的分析新方法

本文提出了一个氢化物发生一冷原子荧光法间接测定痕量锑的新方法。考察了各种实验条件,并将此法用于水及沉积物标样分析,结果令人满意,对水中锑检出限为0.1μg/L,回收率96％～102％。     

Optimization of the determination of selenium in marine samples by atomic absorption spectrometry: Comparison of a flameless graphite furnace atomic absorption system with a hydride generation atomic absorption system

A comparison has been made between a graphite furnace system based on nickel as a matrix stabilizing metal and an automated hydride generation system with a heated quartz cell. The effect of nickel as a matrix modifier was studied in pure selenite solutions as well as in biological matrixes by different charring temperatures. The suppression effect of different acids on the response of the analyte is reported and discussed. The use of an electrically heated quartz tube as an alternative to the argon hydrogen flame method unproved the selenium determination by hydride generation atomic absorption. The effect of hydrochloric acid to secure quantitative formation of selenium (IV) and the interference of copper in the response measurements have been studied. Further a comparison has been made between three different digestion procedures when the hydride generation atomic absorption system was applied. The results of the graphite furnace atomic absorption and the hydride generation atomic absorption were found to be equally accurate, but the graphite furnace technique gave better reproducibility.     

气相富集原子光谱分析技术研究进展

作为一种简单、高效、低耗的预富集方法,气相富集技术(GPE)可作为原子光谱仪器的关键部件用以提高分析灵敏度、消除基体干扰,在原子光谱的小型化、现场化研究领域已得到广泛应用。GPE是通过氢化物发生、紫外蒸气发生、电热蒸发等进样方式使样品转换为气态分析物,被石英、碳、金属等材料捕获在富集装置中,其中捕获/释放条件也是决定元素预富集的关键因素,主要包括冷捕获、合金捕获、热捕获、介质阻挡放电等富集/释放方式。该文综述了GPE技术在原子光谱领域的研究进展,从进样方式、捕获材料、捕获/释放方式等方面进行了分析与探讨,并对其研究和应用前景进行了展望。     

Preconcentration and in-situ photoreduction of trace selenium using TiO2 nanoparticles, followed by its determination by slurry photochemical vapor generation atomic fluorescence spectrometry

We have developed a method for the determination of trace levels of total selenium in water samples. It integrates preconcentration, in-situ photoreduction and slurry photochemical vapor generation using TiO₂ nanoparticles, and the determination of total selenium by AFS. The Se(IV) and Se(VI) species were adsorbed on a slurry of TiO₂ nanoparticles which then were exposed to UV irradiation in the presence of formic acid to form volatile selenium species. The detection limits were improved 17-fold compared to hydride generation and 56-fold compared to photochemical vapor generation, both without any preconcentration. No significant difference was found in the limits of detection (LODs) for Se(IV) and Se(VI). The LOD is as low as 0.8 ng L^?1, the precision is better than 4.5 % (at a level of 0.1 μg L^?1 of selenium). The method gave good recoveries when applied to the determination of total selenium in a certified tissue reference material (DORM-3) and in spiked drinking water and wastewater samples containing high concentrations of transition and noble metal ions. It also excels by very low LODs, a significant enhancement of sample throughput, reduced reagent consumption and sample loss, and minimal interference by transition and noble metal ions.

开叉毛细管HG-FAAS测定地质样品中的锑、铋

氢化物发生原子吸收法(HG-FAAS)广泛应用于冶金、地质、环境、医药和食品分析等领域中。研究表明,氢化物发生法的检出限、测定精度以及干扰等情况与原子化器和氢化物发生器的结构以及传输过程有关[1]。郭小伟等[2-4]研制了用于火焰原子吸收光谱分析的双毛细管喷雾器,并利用其测     

Hyphenation of flow injection/sequential injection with chemical hydride/vapor generation atomic fluorescence spectrometry

The dominant role played by flow injection/sequential injection (FI/SI, including lab-on-valve, LOV) in automatic on-line sample pretreatments coupling to various detection techniques is amply demonstrated by the large number of publications it has given rise to. Among these, its hyphenation with hydride/vapor generation atomic fluorescence spectrometry (HG/VG-AFS) has become one of the most attractive sub-branches during the last years, attributed not only to the high sensitivity of this technique, but also to the superb separation capability of hydride/vapor forming elements from complex sample matrices. In addition, it also provides potentials for the speciation of the elements of interest.It is worth mentioning that quite a few novel developments of sample pretreatment have emerged recently, which attracted extensive attentions from the related fields of research. The aim of this mini-review is thus to illustrate the state-of-the-art progress of implementing flow injection/sequential injection and miniaturized lab-on-valve systems for on-line hydride/vapor generation separation and preconcentration of vapor forming elements followed with detection by atomic fluorescence spectrometry, within the period from 2004 up to now. Future perspectives in this field are also discussed.     

Behaviour of the dithiocarbamate complexes of arsenic, antimony, bismuth, mercury, lead, tin and selenium in methanol with a hydride generator

A study was carried out with a continuous hydride generator coupled to an atomic emission spectrometer with inductively-coupled plasma to determine whether hydrides of As, Bi, Pb, Sb, Sn and Se and mercury vapor could be generated in methanol solutions of their dithiocarbamate complexes. It was found that (with the exception of Pb) hydride generation with sufficient efficiency for simultaneous multi-element determination is achieved using 0.25% NaBH(4)-0.6 mol 1(-1) HCl as reaction medium. The detection limit was found to be 0.2 ng ml(-1) for As, 30 ng ml(-1) for Bi, 0.03 ng ml(-1) for Se, Sb and Sn.     

Determination of mercury by furnace atomic nonthermal excitation spectrometry

The determination of Hg using different variants of the Furnace Atomic Nonthermal Excitation Spectrometry (FANES) is described. In the direct analysis of micro volumes of solutions, the results could be improved by working with chemical modifiers for the stabilization of Hg during the thermal pretreatment. The best results were obtained using Ir and Pd as modifiers, with absolute detection limits of 4 and 12 pg, respectively. The determination of mercury in sample volumes up to 10 ml could be achieved by coupling a cold vapour generation system and an amalgam attachment to the FANES source. A detection limit of 22 was obtained with this technique. The best results were obtained by using the cold vapour generation technique and in situ enrichment of Hg onto the modified inner surface of the graphite tube of the FANES source. Using Ir for permanent impregnation of the tube a detection limit of 0.0009 was found. The influence of hydride forming elements on the determination of mercury by the technique of vapour generation and in situ enrichment was studied. A reduction of the concentration of NaBH₄ to 0.002% m/v made it possible to determine traces of mercury in presence of a high excess of hydride forming elements without any depression of the Hg emission intensity.The results were validated using standard reference materials.     

Determination of zinc in food using atomic fluorescence spectrometry by hydride generation from organized media

A method was proposed for the determination of zinc by atomic fluorescence spectrometry with hydride generation from surfactant-based organized media. The ability of different nature micelles to improve hydride generation of zinc was investigated using an intermittent flow hydride generator and the possible mechanism was discussed. The advantages of hydride generation from the organized media of cetyltrimethylammonium bromide (CTAB) were contrasted with that from aqueous media in sensitivity and precision of the zinc determination. The micellar media of CTAB improved the hydride generation processes of zinc both thermodynamically and kinetically. In addition some transition metals, presumably metal borides, were found to catalyze the hydrogenation of zinc. The proposed method has been validated by the determination of zinc in the certified reference materials using the standard addition method with satisfactory result.     

Electrochemical generation of mercury cold vapor and its in-situ trapping in gold-covered graphite tube atomizers

The combination of more efficient flow-through electrochemical mercury cold vapor generation with its in-situ trapping in a graphite tube atomizer is described. This coupled technique has been optimized to attain the maximum sensitivity for Hg determination and to minimize the limits of detection and determination. A laboratory constructed thin-layer flow-through cell with a platinum cathode served as the cold vapor generator. Various cathode arrangements with different active surface areas were tested. Automated sampling equipment for the graphite atomizer with an untreated fused silica capillary was used for the introduction of the mercury vapor. The inner surface of the graphite tube was covered with a gold foil placed against the sampling hole.     

Mechanism of multi‐metal(loid) methylation and hydride generation by methylcobalamin and cob(I)alamin: a side reaction of methanogenesis

Metal(loid)s are subject to many transformation processes in the environment, such as oxidation, reduction, methylation and hydride generation, predominantly accomplished by prokaryotes. Since these widespread processes affect the bioavailability and toxicity of metal(loid)s to a large extent, the investigation of their formation is of high relevance. Methanogenic Archaea are capable of methylating and hydrogenating Group 15 and 16 metal(loid)s arsenic, selenium, antimony, tellurium, and bismuth due to side reactions between central methanogenic cofactors, methylcobalamin (CH₃Cob(III)) and cob(I)alamin (Cob(I)). Here, we present systematic mechanistic studies on methylation and hydride generation of Group 15 and 16 metal(loid)s by CH₃Cob(III) and Cob(I). Pentavalent arsenical species showed neither methylation nor reduction as determined by using a newly developed oxidation state specific hydride generation technique, which allows direct determination of tri‐ and pentavalent arsenic species in a single batch. In contrast, efficient methylation of trivalent species without a change in oxidation state indicated that the methyl transfer does not proceed via a Challenger‐like oxidative methylation, but via a non‐oxidative methylation. Our findings also point towards a similar mechanism for antimony, bismuth, selenium, and tellurium. Overall, we suggest that the transfer of a methyl group does not involve a free reactive species, such as a radical, but instead is transferred either in a concerted nucleophilic substitution or in a caged radical mechanism. For hydride generation, we propose the intermediate formation of hydridocobalamin, transferring a hydride ion to the metal(loid)s. Copyright © 2012 John Wiley & Sons, Ltd.     

电解冷蒸气发生原子荧光法测定痕量汞

以电解冷蒸气发生技术结合原子荧光光谱仪,采用自行设计的圆盘电解池,进行汞的电解还原冷蒸气发生情况的研究.实验表明,铂作为阴极时,Hg的电化学发生响应信号与化学还原法获得的信号强度相当;同时发现,载气引入位置是影响Hg响应信号强度的重要因素.在1.0 mol/L H2SO4作为阴极液及0.8 A的电解电流条件下,Hg的检出限为1.2 ng/L(3σ); 相对标准偏差为1.7%(n=11).利用此体系分析了标准物质及生物样品中的痕量汞,结果满意.     

Co-Hydride Enhancement Effects in Cadmium,Zinc and Thallium Hydride Generation Measurements

Until recently hydride generation (HG) technique had been applied to only a limited number of elements. In attempts to extend the technique to cadmium, Guo and Guo found that the presence of thiourea together with cobalt enhanced the signal intensity of the Cd volatile species. This finding was repeated and confirmed by many authors. Moreover, Ga and Si, Fe and Ni were used to improve the sensitivity for Cd determination. Recently, the vapour generation of Zn species was performed using an intermittent flow reactor by Guo and Guo,it was found that Ni and Co ions greatly enhanced the signal intensity of zinc. Early in 1984,Yan and co-works reported that the addition of hydride-forming elements, especially tellurium, "accelerated" the formation of thallium hydride rapidly, and suggested a complex hydride was formed. According to these reports, it seems that the addition of certain foreign ions has a positive effect to such elements as Cd, Zn, and Tl, which form unstable hydrides. But the mechanism of the effect of these foreign ions remains unexplained.     

萃取-非水介质氢化物发生-ICP-AES中的干扰及Ni-Fe基合金的分析

本文结合溶剂萃取研究了非水介质中氢化物发生-ICP-AES的分析条件、干扰等因素的影响。利用KI~+H_2SO_4/MIBK萃取体系将As,Sb,Bi萃取到MIBK中而与基体元素分离,然后将该有机相与甲酸按等体积混合后,即可直接进行氢化物发生-ICP-AES分析。还对影响萃取和氢化物发生的一些因素及共存元素的干扰进行了讨论。该方法应用于Ni-Fe基合金中As和Sb的分析,取得了较满意的结果。     

Simultaneous determination of arsenic, antimony, selenium and tin by gas phase molecular absorption spectrometry after two step hydride generation and preconcentration in a cold trap system

A cold trap system for the simultaneous determination of arsenic, antimony, selenium and tin by continuous hydride generation and gas phase molecular absorption spectrometry is described. The hydride generation is carried out in two steps; first, tin hydride is generated at low acidity and second, arsenic, antimony and selenium hydrides are formed at higher acidity. All the hydrides are collected in a liquid nitrogen cryogenic trap and transported to the flow cell of a diode array spectrophotometer, where molecular absorption spectra are obtained in the 190-250 nm range. Five calibration solutions containing arsenic, antimony, selenium and tin are solved using multiple linear regression analysis. Tests are performed in order to extend the same manifold to other hydrides but no signals are obtained for bismuth, cadmium, lead, tellurium and germanium. Under the optimum conditions found and using the wavelengths of maximum sensitivity (190, 198, 220 and 194 nm), the analytical characteristics of each element are calculated. The detection limits are 0.050, 0.020, 0.12 and 1.1 mug ml(-1) and the RSD values are 3.7, 3.1, 3.5 and 3.0% for As, Sb, Se and Sn, respectively. The method is applied to As, Sb, Se and Sn determination in natural spiked water samples.     

Determination of mercury by electrochemical cold vapor generation atomic fluorescence spectrometry using polyaniline modified graphite electrode as cathode

An electrochemical cold vapor generation system with polyaniline modified graphite electrode as cathode material was developed for Hg (II) determination by coupling with atomic fluorescence spectrometry. This electrochemical cold vapor generation system with polyaniline/graphite electrode exhibited higher sensitivity; excellent stability and lower memory effect compared with graphite electrode electrochemical cold vapor generation system. The relative standard deviation was 2.7% for eleven consecutive measurements of 2 ng mL^− 1 Hg (II) standard solution and the mercury limit of detection for the sample blank solution was 1.3 рg mL^− 1 (3σ). The accuracy of the method was evaluated through analysis of the reference materials GBW09101 (Human hair) and GBW 08517 (Laminaria Japonica Aresch) and the proposed method was successfully applied to the analysis of human hairs.     

UV light-emitting-diode photochemical mercury vapor generation for atomic fluorescence spectrometry

A new, miniaturized and low power consumption photochemical vapor generation (PVG) technique utilizing an ultraviolet light-emitting diode (UV-LED) lamp is described, and further validated via the determination of trace mercury. In the presence of formic acid, the mercury cold vapor is favourably generated from Hg(2+) solutions by UV-LED irradiation, and then rapidly transported to an atomic fluorescence spectrometer for detection. Optimum conditions for PVG and interferences from concomitant elements were investigated in detail. Under optimum conditions, a limit of detection (LOD) of 0.01 μg L(-1) was obtained, and the precision was better than 3.2% (n = 11, RSD) at 1 μg L(-1) Hg(2+). No obvious interferences from any common ions were evident. The methodology was successfully applied to the determination of mercury in National Research Council Canada DORM-3 fish muscle tissue and several water samples.     

Improvement in arsenic speciation,using hydride generation and atomic absorption spectrophotometry

Improvements in arsenic speciation in sea-water using hydride generation, cold trapping and AAS are reported. Progressive addition of sodium tetrahydroborate and pH optimization are essential to obtain reliable results. The response factor for As^III, As^v, methylarsonic acid and dimethylarsinic acid is nearly the same when sulphuric acid is used for the hydride generation step.     

Determination of Antimony in Brass by On-line Hydride Generation Atomic Fluorescence Spectrometry Alkaline Solution

The hydride generation(HG) technique combined with atomic spectrometry as a detection system has become one of the most powerful analytical tools for the determination of elements, such as As, Sb, Bi, Se, Te,Ge, Sn and Pb. Normally, the hydride is generated by the reaction between an acidic sample solution with tetrahydroborate. However, when some inorganic ions such as the transition metal ions are present in the reaction matrix, interference arise. Some approaches for minimizing the interference have been suggested, including the addition of various reagents such as thiourea and iron(III) solution. Interfering metals can also be removed by precipitation. The procedure involved filtration before the solution was acidified. In order to reduce the steps of the process, hydride generation from alkaline solution was described for the determination of selenium in copper and nickel materials.