End-grafted low-molecular-weight PNIPAM does not collapse above the LCST

The interfacial properties of end-grafted temperature-responsive poly(N-isopropylacryamide) (PNIPAM) were quantified by direct force measurements both above and below the lower critical solution temperature (LCST) of 32 degrees C. The forces were measured between identical, opposing PNIPAM films and between a PNIPAM film and a lipid membrane. At the grafting densities and molecular weights investigated, the polymer extension did not change significantly above the LCST, and the polymers did not adhere. Below the LCST, the force-distance profiles suggest a vertical phase separation, which results in a diluter outer layer and a dense surface proximal layer. At large separations, the force profiles agree qualitatively with simple polymer theory but deviate at small separations. Importantly, at these low grafting densities and molecular weights, the end-grafted PNIPAM does not collapse above the LCST. This finding has direct implications for triggering liposomal drug release with end-grafted PNIPAM, but it increases the temperature range where these short PNIPAM chains function as steric stabilizers.     

Adsorption isotherms and dissipation of adsorbed poly(N-isopropylacrylamide) in its swelling and collapsed states

Poly(N-isopropylacrylamide) (PNIPAM) physisorbed on gold surfaces in aqueous solutions has been studied using a quartz crystal microbalance with dissipation monitoring (QCM-D). The adsorption isotherms of the polymer, that is, the adsorbed mass versus the concentration of PNIPAM in solution, show distinctly different behaviors at temperatures below and above a lower critical solution temperature (LCST). Below the LCST, PNIPAM forms a single compact layer in solutions with concentrations up to 100 ppm in weight; above the LCST, much thicker films of PNIPAM form in the same concentration range. Changes in the dissipation factor versus solvent concentration show a behavior similar to those in the isotherms. The difference in the adsorption behavior below and above the LCST can be qualitatively explained in terms of the conformation difference of the polymer in its swelling and collapsed states.     

Brush-sheathed particles diffusing at brush-coated surfaces in the thermally responsive PNIPAAm system

Phase-contrast microscopy and particle tracking algorithms are used to study the near-surface diffusion of poly(N-isopropylacrylamide) (PNIPAAm) brush functionalized micron-sized silica microspheres after sedimentation from aqueous suspension onto planar substrates coated with a similar polymer brush above and below the lower critical solution temperature (LCST) of PNIPAAm, 32 degrees C. A small negative charge on the wall and the particles (zeta potential = -6 mV) prevents adhesion above and below the LCST. The near-surface translational diffusion coefficient (D(surface)) is compared to the bulk-phase translational diffusion coefficient (D(bulk)), which was measured by dynamic light scattering. We find that D(surface)/D(bulk) is approximately equal to 0.6 at temperatures T < 32 degrees C but rises abruptly to approximately 0.8-0.9 at T > 32 degrees C. Near-surface diffusion is expected to be slower than bulk diffusion owing to hydrodynamic coupling to the wall, implying reduced hydrodynamic coupling at the higher temperatures, perhaps mediated by enhanced electrostatic repulsion above the LCST transition.     

Alpha,omega-functionalized poly-N-isopropylacrylamides: controlling the surface activity for vesicle adsorption by temperature

The synthesis of alpha,omega-end-functionalized copolymers of N-isopropylacrylamide and N-(3-dimethylaminopropyl)acrylamide was performed. Monomer ratios of 100:0, 96:4, and 81:19 were investigated. The lower critical solution temperature (LCST) of these polymers was determined by cloud-point measurements and by microcalorimetric measurements. The LCST increased from 32 over 37 to 47 degrees C as the hydrophobicity increased with increasing amount of comonomer N-(3-dimethylaminopropyl)acrylamide. The polymers could successfully be adsorbed onto gold surfaces. Finally, vesicle adsorption onto these self-assembled polymer films on flat gold surfaces was investigated as the vesicle solution temperature was varied. It could be observed that vesicle adsorption was hindered as long as the temperature of the vesicle solution was above the LCST of the polymer. As soon as it dropped below the LCST the vesicle adsorption process was initiated.     

Adsorption behaviors of emulsifiers and biomolecules on temperaturesensitive polymer particles

Adsorption and desorption behaviours of emulsifiers and biomolecules on the two kinds of temperature-sensitive composite polymer particles were compared. One (I) was produced by seeded emulsion copolymerization of dimethylaminoethyl methacrylate and ethylene glycol dimethacrylate with 0.17 m-sized polystyrene seed particles. The other (II) was produced by seeded emulsion copolymerization of N-isopropylacrylamide (NIPAM) and N,N-methylenebisacrylamide with 0.36 m-sized styrene-NIPAM copolymer particles. The amount of adsorption at temperatures above each lower critical solution temperature (LCST) was found to be much higher for I than II. In both cases, at temperatures below the LCST, almost all lactalbumin hydrolysate molecules adsorbed above the LCST were desorbed but the desorptions of adsorbed egg albumin and lysozyme molecules were not so high. The adsorption and desorption were reversible for both particles and the efficiency was better for I than II. From these results, it is concluded that the adsorption/desorption of protein onto the temperature-sensitive polymer particles is controllable by changing the temperature below and above the LCST of the shell layer and the sensitivity is based on the surface property of the composite polymer particles.Part CXLIX of the series Studies on Suspensions and Emulsions     

Direct observation of the phase transition for a poly(N-isopropylacryamide) layer grafted onto a solid surface by AFM and QCM-D

The temperature-induced structural changes of a thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) layer grafted onto a silica substrate were investigated in aqueous solution using an atomic force microscope (AFM) and a quartz crystal microbalance with dissipation (QCM-D). A PNIPAM layer was grafted onto the silicon wafer surface by free radical polymerization of NIPAM to obtain a high molecular weight polymer layer with low-grafting density overall. By AFM imaging, the transition of the grafted PNIPAM chains from a brush-like to a mushroom-like state was clearly visualized: The surface images of the plate were featureless at temperatures below the LCST commensurate with a brush-like layer, whereas above the LCST, a large number of domain structures with a characteristic size of approximately 100 nm were seen on the surface. Both frequency and dissipation data obtained using QCM-D showed a significant change at the LCST. Analysis of these data confirmed that the observed PNIPAM structural transition was caused by a collapse of the brush-like structure as a result of dehydration of the polymer chains.     

Temperature-reversible ultrathin films of N-isopropylacrylamide terpolymer adsorbed at the solid-liquid interface

This article describes the stability and reversibility of ultrathin films of N-isopropylacrylamide (NIPA)-vinylimidazole (VI)-poly(ethylene glycol) (PEG) graft terpolymer adsorbed at the solid-liquid interface upon temperature cycling from below to above its phase transition temperature. The coil-to-globule and globule-to-coil phase transitions were captured by in situ fluid tapping atomic force microscopy (AFM). The film thickness of 1 nm was determined by AFM, X-ray photoelectron spectroscopy, and X-ray reflectivity. The concentration required to reach full coverage was found to be higher when adsorption occurred below the phase transition temperature. From 23 to 42 degrees C, the adsorbed NIPA terpolymer film was observed to be molecularly smooth, corresponding to the close-packed structure of flexible polymer coils. Particles containing between one and a few globules appeared abruptly at the interface at 42-43 degrees C, the same temperature as the solution phase transition temperature, which was determined by dynamic light scattering. The size of the particles did not change with temperature, whereas the number of particles increased with increasing temperature up to 60 degrees C. The particles correspond to the collapsed and associated state of the globules. The film morphological changes were found to be reversible upon temperature cycling. Subtle differences were observed between dip-coated and spin-coated films that are consistent with a higher degree of molecular freedom for spin-coated films. The study contributes to the fundamental understanding and applications of smart ultrathin films and coatings.     

Properties of a novel thermal sensitive polymer based on poly(vinyl alcohol) and its layer‐by‐layer assembly

Structurally modified poly(vinyl alcohol) (PVA) was prepared as novel thermally sensitive polymers by partially acetalyzing and/or ionizing the commercially available PVA. Their aqueous solutions experience completely reversible polymer aggregation and dissolution above and below the lower critical solution temperature (LCST), respectively. The LCST of a partially acetalyzed PVA (APVA) can be readily controlled by the degree of acetalysis or the molecular weight of the starting PVA. Introduction of a small amount of cationic group onto the APVA backbone increases the LCST obviously, while the LCST is highly sensitive to NaCl concentration. Then APVA and cationic APVA multilayers are assembled on rayon to make a thermal responsive fiber. The atomic force microscopy (AFM) images of the surface reveal the increment of roughness stimulated by temperature. Copyright © 2007 John Wiley & Sons, Ltd.     

Adsorption and aggregation of cationic amphiphilic polyelectrolytes on silica

The adsorption of two cationic amphiphilic polyelectrolytes, which are copolymers of two charged monomers, triethyl(vinylbenzyl)ammonium chloride and dimethyldodecyl(vinylbenzyl)ammonium chloride (which is the amphiphilic one) with different contents of amphiphilic groups (40% (40DT) and 80% (80DT)), onto the hydrophilic silica-aqueous solution interface has been studied by in situ null ellipsometry and tapping mode atomic force microscopy (AFM). Adsorption isotherms for both polyelectrolytes were obtained at 25 degrees C and at different ionic strengths, and the adsorption kinetics was also investigated. At low ionic strength, thin adsorbed layers were observed for both polyelectrolytes. The adsorption increases with polymer concentration and reaches, in most cases, a plateau at a concentration below 50 ppm. For the 80DT polymer, at higher ionic strength, an association into aggregates occurs at concentrations at and above 50 ppm. The aggregates were observed directly by AFM at the surface, and by dynamic light scattering in the solution. The adsorption data for this case demonstrated multilayer formation, which correlates well with the increase in viscosity with the ionic strength observed for 80DT.     

Polyelectrolyte multilayers of diblock copolymer micelles with temperature-responsive cores

We report on assembly and stimuli-response behavior of layer-by-layer (LbL) films of pH- and temperature-responsive cationic diblock copolymer micelles (BCMs) of poly(2-(dimethylamino)ethyl methacrylate)-block-poly(N-isopropylacrylamide) (PDMA-b-PNIPAM) and a linear polyanion polystyrene sulfonate (PSS). As a function of solution pH at temperatures above lower critical solution temperature (LCST) of PNIPAM, PDMA-b-PNIPAM micelles have been demonstrated earlier to exhibit an abrupt change in micellar aggregation number and hydrodynamic size between larger and smaller BCMs (LBCMs and SBCMs, respectively). Here, LBCMs or SBCMs were included within LbL films through self-assembly with a polyanion, and film pH and temperature responses were studied using ellipsometry and atomic force microscopy (AFM). Both types of micelle preserved their micellar morphology when adsorbed at the surface of oxidized silicon wafers coated with PSS-terminated precursor layer at a constant pH. Response of adsorbed BCMs to temperature and pH variations was strongly dependent on whether or not BCMs were coated with the PSS layer. While monolayers of LBCMs lost their original dry morphology in response to pH or temperature variations, depositing a PSS layer atop LBCMs inhibited such irreversible restructuring. As a result of wrapping around and strong binding of PSS chains with LBCM micelles, BCM/PSS assemblies preserved their original dry state morphology despite the application of pH and temperature triggers. However, the wet-state film response to pH and temperature stimuli was drastically different. Swelling of BCM/PSS multilayers was strongly affected by temperature but was almost independent of pH due to neutralization of BCM PDMA's coronal charge with PSS. Cycling the temperature below and above PNIPAM's LCST caused PNIPAM chains within BCM cores to swell or collapse, resulting in reversible swelling transitions in the entire BCM/PSS assemblies. Temperature-controlled switching between the hydrophobic and hydrophilic state of assembled micellar cores was also used to regulate the release of a micelle-loaded hydrophobic pyrene dye, whose release rate increased at temperatures below PNIPAM's LCST.     

Nanofiber formation of hydroxylpropylcellulose (HPC)

The aggregative behaviors of hydroxypropylcellulose (HPC) molecules in aqueous solution and on substrates have been observed by employing laser light scattering (LLS) and, after deposition on a mica surface, atomic force microscopy (AFM). LLS studies showed that the HPC molecules formed large aggregates through self-association when the concentration of the solution was above the critical concentration c(t). AFM measurements revealed that when a dilute aqueous solution of HPC molecules was deposited onto a mica substrate at a temperature below its lower critical solution temperature (LCST) thin nanofibers were formed with a height of 0.9 nm, whereas thick nanofibers were formed when an aqueous solution of HPC molecules was deposited onto a substrate above its LCST. Furthermore, the growth of nanofibers led to the formation of fan structures.     

Effect of temperature cycling on the activity and productivity of immobilized β-galactosidase in a thermally reversible hydrogel bead reactor

The enzyme beta-galactosidase has been immobilized within thermally reversible hydrogel beads that exhibit LCST (lower critical solution temperature) behavior. The hydrogel beads containing the immobilized enzymes swell and expand below the LCST and deswell and shrink above the LCST. This behavior is reversible. The enzyme was physically entrapped in a crosslinked hydrogel of a copolymer of N-isopropylacrylamide (NIPAAm) and acrylamide (AAm), and formed as beads in an inverse suspension polymerization. The beads were placed in a packed bed column reactor which was operated in a continuous, single pass mode, either isothermally at 30 or 35 degrees C, or with temperature cycling between 30 and 35 degrees C. The thermal cycling significantly enhanced overall reactor enzyme activity relative to isothermal operation at either the higher or lower temperature. It is postulated that mass transfer rates within the hydrogel beads are greatly enhanced by the movement of water in and out of the beads during the expansion or collapse of the polymer chain network as temperature is cycled.     

PNIPAM chain collapse depends on the molecular weight and grafting density

This study demonstrates that the thermally induced collapse of end-grafted poly(N-isopropylacrylamide) (PNIPAM) above the lower critical solution temperature (LCST) of 32 degrees C depends on the chain grafting density and molecular weight. The polymer was grafted from the surface of a self-assembled monolayer containing the initiator (BrC(CH3)2COO(CH2)11S)2, using surface-initiated atom transfer radical polymerization. Varying the reaction time and monomer concentration controlled the molecular weight, and diluting the initiator in the monolayer altered the grafting density. Surface force measurements of the polymer films showed that the chain collapse above the LCST decreases with decreasing grafting density and molecular weight. At T > LCST, the advancing water contact angle increases sharply on PNIPAM films of high molecular weight and grafting density, but the change is less pronounced with films of low-molecular-weight chains at lower densities. Below the LCST, the force-distance profiles exhibit nonideal polymer behavior and suggest that the brush architecture comprises dilute outer chains and much denser chains adjacent to the surface.     

Bundling and diameter selectivity in HiPco SWNTs poly(p-phenylene vinylene-co-2,5-dioctyloxy-m-phenylene vinylene) composites

Temperature-dependent (TD) Raman measurements at laser excitation 514.5 nm were performed at different concentrations. The spectral profile of the radial breathing modes were investigated up to a polymer concentration of 1 g/L and were found to be dominated by approximately 1.2-1.4 nm diameter tubes at room temperature. Upon heating above the glass transition of the polymer (60 degrees C) the smaller tubes around approximately 0.9 nm increased significantly in relative intensity. This suggests that below the glass transition of the polymer (60 degrees C) RBMs within the composite are damped and spectral changes cannot be interpreted as diameter selective solubilization. The observed RBM damping at room temperature only occurred up to a concentration of approximately 1.2 x 10(-4) g/L and below this no damping was observed. Photoluminescence intensity (PL) measurements were taken for a range of PmPV concentrations, in which HiPco single walled carbon nanotubes (SWNTs) at 100%, 10%, 1%, 0.1%, 0.01%, and 0% mass fractions were added. Fitting of the concentration dependence to a dynamic absorption/desorption model indicates that the polymer interacts with nanotube bundles until a critical concentration of approximately 1.2 x 10(-4) g/L is reached, below which the nanotubes are isolated. The polymer and or solvent has a significant effect on the debundling and aggregation within these systems. Aggregation and/or interaction with the polymer at higher concentrations can effect the RBM profile in the composite at ambient temperatures, providing an incomplete representation of the selection of diameters present within composites at a particular wavelength.     

Controlled nitroxide-mediated styrene surface graft polymerization with atmospheric plasma surface activation

Polymer layer growth by free radical graft polymerization (FRGP) and controlled nitroxide-mediated graft polymerization (NMGP) of polystyrene was achieved by atmospheric pressure hydrogen plasma surface activation of silicon. Kinetic polystyrene layer growth by atmospheric pressure plasma-induced FRGP (APPI-FRGP) exhibited a maximum surface-grafted layer thickness (125 A after 20 h) at an initial monomer concentration of [M] 0 = 2.62 M at 85 degrees C. Increasing both the reaction temperature ( T = 100 degrees C) and initial monomer concentration ([M] 0 = 4.36 M) led to an increased initial film growth rate but a reduced polymer layer thickness, due to uncontrolled thermal initiation and polymer grafting from solution. Controlled atmospheric pressure plasma-induced NMGP (APPI-NMGP), using 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO), exhibited a linear increase in grafted polystyrene layer growth with time due to controlled surface graft polymerization as well as reduced uncontrolled solution polymerization and polymer grafting, resulting in a polymer layer thickness of 285 A after 60 h at [TEMPO] = 10 mM, [M] 0 = 4.36 M, and T = 120 degrees C. Atomic force microscopy (AFM) surface analysis demonstrated that polystyrene-grafted surfaces created by APPI-NMGP exhibited a high surface density of spatially homogeneous polymer features with a low root-mean-square (RMS) surface roughness ( R rms = 0.36 nm), similar to that of the native silicon surface ( R rms = 0.21 nm). In contrast, polymer films created by APPI-FRGP at [M] 0 = 2.62 M demonstrated an increase in polymer film surface roughness observed at reaction temperatures of 85 degrees C ( R rms = 0.55 nm) and 100 degrees C ( R rms = 1.70 nm). The present study concluded that the current approach to APPI controlled radical polymerization may be used to achieve a grafted polymer layer with a lower surface roughness and a higher fractional coverage of surface-grafted polymers compared to both conventional FRGP and APPI-FRGP.     

Switchable surface traps for injectable bead-based chromatography in PDMS microfluidic channels

We report here a reversible microchannel surface capture system for stimuli-responsive grafted bioanalytical beads. Poly(N-isopropylacrylamide) (PNIPAAm) was grafted onto polydimethylsiloxane (PDMS) surfaces by a UV-mediated graft polymerization from a photoinitiator that was preadsorbed in the channel wall. The surface grafting density and resulting switchable hydrophilic/hydrophobic properties were controlled by varying the photo-illumination times and/or the initiator concentration. At limiting PNIPAAm-graft densities, the surfaces demonstrated minimal contact angles of 35 degrees below the lower critical solution temperature (LCST) and maximal contact angles of 82 degrees above it. These contact angles could be varied depending on the graft density. The surface grafts are spatially limited to the photo-illuminated region to define where the trap is constructed. The surface traps capture PNIPAAm-grafted nanobeads uniformly above the LCST and facilitate their rapid release as the temperature is reversed to below the LCST. This dual surface trap and injectable chromatography system could be useful in many applications, such as affinity separations, immunoassays, and enzyme bioprocesses, by providing for the controlled capture and release of chromatography beads.     

Contrary hydration behavior of N-isopropylacrylamide to its polymer, P(NIPAm), with a lower critical solution temperature

The number of hydrated water molecules per N-isopropylacrylamide in homogeneous aqueous solution was determined to be a constant with a value of 5-6 below and above the lower critical solution temperature, LCST (32 degrees C), of its polymer, poly(N-isopropylacrylamide), by high-frequency dielectric relaxation techniques.     

Switchable photoluminescence of CdTe nanocrystals by temperature-responsive microgels

In the present study, we report a method for preparing a fluorescent thermosensitive hybrid material based on monodisperse, thermosensitive poly( N-isopropyl acrylamide) (PNIPAM) microgels covered with CdTe nanocrystals of 3.2 nm diameter. The CdTe nanocrystals were covalently immobilized on the surface of PNIPAM microgels. The chemical environment around the CdTe nanocrystals was modified by changing the temperature and inducing the microgel volume-phase transition. This change provoked a steep variation in the nanocrystal photoluminescence (PL) intensity in such a way that when the temperature was under the low critical solution temperature (LCST) of the polymer (36 degrees C) the PL of the nanocrystals was strongly quenched, whereas above the LCST the PL intensity was restored.     

Adaptive nanomechanical response of stratified polymer brush structures

We have fabricated a stratified polymer surface film with tunable thickness (within 17-34 nm) through facile, room-temperature, UV-initiated polymerization with a temperature-sensitive pNIPAAM layer confined beneath a hydrophobic layer. AFM morphology and ellipsometric measurements were measured at each grafting step, along with XPS measurements of the overall layer to verify layer growth. The strong characteristic LCST behavior of pNIPAAM was observed in water, with a 100% change in thickness above and below this transition. The AFM nanomechanical results demonstrate vertical gradients of the elastic response tunable to a desired state by the external temperature. These temperature-sensitive, adaptive polymer structures with the pNIPAAM layer "hidden" beneath the rubbery, hydrophobic PBA topmost layer represent an interesting example of nanoengineering surfaces with properties such as adhesion, elastic modulus, and multi-level structural reorganization responsive to fluidic and temperature variations that can be important for biological purposes such as implant coatings, cell-surface mimicry, and drug delivery vehicles.     

Polymerization of Acrylamide in Aqueous Solution of Poly(N‐isopropylacrylamide) at Lower Critical Solution Temperature

Acrylamide (AAm) was found to polymerize in a solution of poly(N‐isopropylacrylamide) (PNIPAAm) in water at around its lower critical solution temperature (LCST) (32°C) without any initiators. This phenomenon was specifically observed in aqueous solutions of the polymers having LCST such as PNIPAAm and poly(methylvinylether) (PMVE). AAm polymerized only when PNIPAAm and AAm were dissolved in water below LCST of PNIPAAm and then the solution was warmed up to the polymerization temperature (40°C). On the other hand, the polymerization of AAm did not proceed when AAm was added into aqueous PNIPAAm solution during and after the phase separation above 32°C. Furthermore the polymerizability of AAm was remarkably affected by the concentration and molecular weight of the PNIPAAm additives. Under the condition of lower PNIPAAm concentration (0.30 mol/L), the increase in the molecular weight of PNIPAAm considerably increased the molecular weight of the resulting PAAm but decreased the yield of PAAm. Under the condition of higher PNIPAAm concentration (0.60 mol/L) the polymerizability was not so affected by the molecular weight of PNIPAAm, while the molecular weight of PAAm formed by using higher molecular weight PNIPAAm was higher than those of PAAm formed by using lower molecular weight PNIPAAm. Moreover, the molecular weight of PAAm formed by the PNIPAAm induced polymerization of AAm was much higher than that of the polymer obtained by the radical polymerization using AIBN in THF or VA‐ 061 in water.