Pyrrole-based conductive polymer as the solid-phase extraction medium for the preconcentration of environmental pollutants in water samples followed by gas chromatography with flame ionization and mass spectrometry detection

A pyrrole-based polymer was synthesized and applied as a new sorbent for solid-phase extraction (SPE) of some environmental pollutants from water samples. Polypyrrole (PPy) was synthesized by chemical oxidation of the monomer in nonaqueous solution. SPE of selected phenols, pesticides, and polyaromatic hydrocarbons (PAHs) from aqueous samples were performed using 200 mg PPy. The determination was subsequently carried out by gas chromatography-flame ionization detection (GC-FID) and gas chromatography-mass spectrometry (GC-MS). The polymer showed much higher recoveries for aromatic compounds than aliphatics. Preconcentration of sample volumes up 11 led to acceptable recoveries for aromatic and other tested polar compounds. The R.S.D. for a river water sample spiked with phenols, pesticides and PAHs at sub-ppb level was lower than 10% (n = 3) and limits of detection for these compounds were between 15 and 120 ng l(-1).     

beta-Cyclodextrin-bonded silica particles as the solid-phase extraction medium for the determination of phenol compounds in water samples followed by gas chromatography with flame ionization and mass spectrometry detection

A new absorbent for solid-phase extraction (SPE) was prepared by a beta-cyclodextrin bonded silica stationary phase (CDS) has been applied to determine the concentrations of phenol compounds in water samples. SPE of selected phenolic compounds from aqueous samples were performed using 250 mg CDS. The determination was subsequently carried out by gas chromatography-flame ionization detection (GC-FID) and gas chromatography-mass spectrometry (GC-MS). Compared with available SPE, the CDS showed high sensitivity and fast velocity of mass transfer for phenolic compound because of its porous structure of beta-cyclodextrin. The relative standard deviation (RSD) for river water sample spiked with phenolic compounds at sub-ppb level was lower than 10% and limit of detection (LOD) for these compounds were between 10 and 100 ng l(-1).     

Determination of local anaesthetics in body fluids by gas chromatography with surface ionization detection

Ten local anaesthetics were tested for their detection by gas chromatography (GC)-surface ionization detection (SID). Lidocaine, mepivacaine and bupivacaine were detected with the highest sensitivity; their detection limit was 5-10 pg in an injected volume. The sensitivity of other drugs, such as procaine, dibucaine tetracaine and oxybuprocaine, was an order of magnitude lower than that of the above three local anaesthetics. A detailed procedure for isolation of local anaesthetics from human whole blood and cerebrospinal fluid (CSF) by the use of Sep-Pak C18 cartridges, before the GC-SID, is also presented. The recovery of lidocaine, mepivacaine and bupivacaine, which had been added to 1 ml of whole blood or CSF, was close to 100%.     

Detection of organophosphate pesticides in human body fluids by headspace solid-phase microextraction (SPME) and capillary gas chromatography with nitrogen-phosphorus detection

Summary Organosphosphate pesticides have been found extractable by headspace solid-phase microextraction (SPME), and the best conditions of their extraction from human whole blood and urine samples have been investigated. The body fluid samples containing nine pesticides (IBP, methyl parathion, fenitrothion, malathion, fenthion, isoxathion, ethion, EPN and phosalone) were heated at 100°C in a septum-capped vial in the presence of various combinations of acid and salts, and SPME fiber was exposed to the headspace of the vial to allow adsorption of the pesticides before capillary gas chromatography (GC) with nitrogen-phosphorus detection. The heating with distilled water/HCl/(NH₄)₂SO₄/NaCl and with distilled water/HCl gave the best results for urine and whole blood, respectively. Recoveries of the nine pesticides were 0.8–10.6% except for phosalone (0.03%) for whole blood, and 3.8–40.2% for urine. The calibration curves for the pesticides showed linearity in the range of 50–400 ng/0.5 mL for whole blood except for malathion (100–400 ng/0.5 mL whole blood) and 7.5–120 ng/0.5 mL for urine except for phosalone (15–120 ng/0.5 mL urine) with detection limits of 2.2–40 ng/0.5 mL for whole blood and 0.8–12 ng/0.5 mL for urine.     

Analysis of endosulfan isomers and endosulfan sulfate in air and tomato leaves by gas chromatography with electron-capture detection and confirmation by gas chromatography-mass spectrometry

Rapid analytical methods for the determination of endosulfan isomers and endosulfan-sulfate in air and plant samples were developed. The insecticides were trapped from air using a column containing Florisil and extracted with a low volume of ethyl acetate, assisted by sonication. Pesticide residues were determined by gas chromatography with electron-capture detection using a nonpolar capillary column. Residue identities were confirmed by gas chromatography coupled with mass spectrometry. Recoveries of these compounds from air samples were always higher than 78% with an RSD lower than 11% and the detection limits obtained were at least 0.3 ng/l air. Leaf samples were homogenised with ethyl acetate and extracts cleaned-up on an aluminium oxide column. Pesticides were eluted with a hexane-ethyl acetate (80:20, v/v) mixture. Recoveries obtained from plant samples were higher than 78% with an RSD lower than 14% and detection limits in leaves were 0.02 microg/g for each pesticide. These methods were applied to study the volatilisation of endosulfan from tomato leaves under laboratory conditions. A volatilisation rate near 1% of the initial amount of endosulfan per hour was obtained during the first 24 h at room temperature.     

基于多壁碳纳米管修饰电极的保泰松的电致化学发光检测

基于保泰松对联吡啶钌的电致化学发光信号有较强的增敏作用, 使用多壁碳纳米管修饰玻碳电极作为工作电极, 建立了一种保泰松的电致化学发光检测方法. 对测定条件进行了一系列优化, 结果表明, 当发光试剂联吡啶钌的浓度为1.0×10－5 mol/L时, 在0.05 mol/L pH 10.20 的Na2HPO4-NaOH介质中保泰松对联吡啶钌电化学发光信号的增敏效果最强. 在此条件下, 保泰松的线性范围为0.5～200 μmol/L, 检测限(S/N＝3)为0.2 μmol/L, 与使用未经修饰的裸玻碳电极相比, 检测限下降了约一个数量级. 该检测方法还被用于加标人血清样品中保泰松的测定, 回收率在85.3%～95.0%之间, 结果令人满意, 可望用于保泰松的药物临床分析与质量监控.     

Confirmation of phenylbutazone residues in bovine kidney by liquid chromatography/mass spectrometry

A confirmatory method is described for phenylbutazone (PB) residues in bovine kidney tissue. Ground kidney tissue is diluted with water, and the mixture is made basic with 25% ammonium hydroxide in water; the lipids are extracted with ethyl and petroleum ethers. The ether layer is discarded, and the tissue is acidified with 6N HCl. PB residues are extracted with tetrahydrofuranhexane (1 + 4). The extract is passed through a silica solid-phase extraction column, and the eluate is evaporated to dryness. The residue is dissolved in acidified acetonitrile-water-acetic acid (50 + 49.4 + 0.6). A single quadrupole mass spectrometer coupled to a liquid chromatograph with an electrospray interface is used to confirm the identity of the PB residues in the kidney extract. Negative-ion detection with selected-ion monitoring of 4 ions is used. Sets of control and fortified-control kidney tissues (at 50, 100, and 200 ppb PB) and several kidney tissue field samples were analyzed for method validation. The method was tested further during the course of a survey to determine the incidence of PB residues in bovine kidney samples obtained from slaughterhouses across the country. In addition, the method was tested for use with an ion-trap mass spectrometer coupled to a liquid chromatograph, which allowed confirmation of PB at lower levels (5-10 ppb) in kidney tissue.     

Permeability and morphology of poly(cis‐butadiene)/ester‐ether liquid crystal composite membranes

Various amounts of diethylene glycol bis[4‐(4′‐ethoxybenzoyloxy)benzoate] (DEBEB) were added into a poly(cis‐butadiene) (PB) membrane to improve its gas permeation ability. This type of rubber/liquid crystal (LC) composite membranes showed two obvious characteristics that are different from the gas permeation behavior reported in previous literature: (1) The permeabilities to O₂, N₂, and CO₂ were enhanced at room temperature, for example, the permeabilities for the PB/DEBEB (90/10) membrane were higher above six times than those of PB membrane under the same conditions. It is suggested that the interface microvoids probably existed on pontes between polar crystal domains and nonpolar PB matrix. (2) All relationships between the permeability coefficient (P) and temperature (T) were characterized by N‐shape, that is, there were the peaks and valleys on the P‐T curves. Furthermore, morphology studies demonstrated that when DEBEB content in the membranes was above 10 wt %, it was spherically dispersed and embedded in the PB matrix in a crystal domain state. Gas permeation characteristics of the composite membranes were appropriately interpreted as together influence results of DEBEB phase transition behavior and the membrane morphology. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1833–1840, 2000     

Determination of diphenylmethane antihistaminic drugs and their analogues in body fluids by gas chromatography with surface ionization detection.

Eleven diphenylmethane antihistaminic drugs and their analogues were tested for their detection by capillary gas chromatography (GC) with surface ionization detection (SID). The GC-SID response was highest for doxylamine, diphenhydramine and orphenadrine and lowest for terodiline, clemastine and pipethanate. The detection limits for drugs with the highest response were 2-5 pg (ca. 6-20 fmol) on-column (100-250 pg/ml of body fluid). The detection limits with GC-SID were 10-100 times higher than those with GC with nitrogen-phosphorus detection. A detailed procedure for the isolation of the antihistaminics from human whole blood and urine by the use of Sep-Pak C18 cartridges, prior to GC-SID, is also presented. The recoveries of the drugs (50 or 500 pmol), which had been added to 1 ml of body fluids, were > 60%. The baselines remained steady as the column temperature was increased and the background was clean, especially for whole blood extracts.     

Solidification of floating organic droplet microextraction for determination of seven insecticides in fruit juice,vegetables and agricultural runoff using gas chromatography with flame ionization and mass spectrometry detection

Liquid microextraction employing solidification of the floating organic droplet, with vortexing and heating to optimize extraction efficiency, was developed for the determination of seven insecticides in fruit juice, vegetables, and agricultural runoff water. The extracts were analyzed by gas chromatography with both flame ionization and mass spectrometry detection for the determination of chlorpyrifos, prothiofos, profenofos, ethion, λ‐cyhalothrin, permethrin, and cypermethrin, respectively. Using 20 μL of 1‐undecanol in 10 mL of aqueous solution containing 1% w/v sodium chloride provided preconcentration factor of 500. The enrichment factor of the analytes was in the range of 355 to 509 with extraction recovery >71%. The linearity ranges were 4–200 μg/kg for gas chromatography with flame ionization detection and 1–100 μg/kg for gas chromatography with mass spectrometry, with limits of detection ranging from 0.04 to 1.2 μg/kg, which are lower than the international maximum residue limits for vegetables and fruit juice. Intra‐day and inter‐day precisions are less than 5.4 and 7.0% relative standard deviation, respectively. The method was successfully applied to the determination of the seven insecticides in samples of vegetables, fruit juice and agricultural runoff, with recoveries ranging from 61.7 to 120.8%. The extraction method is simple, efficient and environmentally friendly.     

Optimizing the quadruple-potential waveform for the pulsed amperometric detection of neomycin

Determination of neomycin is important for quality control of the pharmaceutical preparation. A quadruple-potential waveform used for pulsed amperometric detection of neomycin was investigated. The waveform cleans the electrode by application of a potential more negative than the potential limit to avoid the formation of gold oxide during applying positive potential to clean gold electrode, thus decreasing the dissolution resulting recession of the gold working electrode within gold oxide formation/reduction cycles in the triple-potential waveform. Waveform parameters were optimized to maximize the signal-to-noise ratio (S/N). The detection limit of neomycin B is lower than 0.01 microg/ml. The linearity of framycetin (plotted as peak area of neomycin B) ranges from 0.05 to 100 microg/ml with correlation coefficient 0.9998. R.S.D. (n = 60) of the peak area of neomycin B is lower than 2%. The quadruple-potential waveform shows low detection limits and long-term reproducibility.     

Development and validation studies for determination of phenylpropanoid‐substituted flavan‐3‐ols in semipurified extract of Trichilia catigua by high‐performance liquid chromatography with photodiode array detection

The phenolic compounds are the main phytochemical constituents of the bark of Trichilia catigua and are commonly used for medicinal purposes. An HPLC method for the simultaneous quantification of phenolic compounds (procyanidin B2 (PB2), epicatechin (EPC), chinchonains Ia, Ib, IIa, IIb, catechin, and chrologenic acid) in T. catigua extract was developed and validated. A suitable chromatographic system was selected, which uses a gradient elution with methanol/ACN (75:25), and water both with 0.05% TFA, as mobile phase, column Luna, 280 nm, and flow 0.4 mL/min. Validation of the analytical method was based on the parameters: linearity, precision, LODs and LOQs, accuracy, robustness, and stability. The method showed linearity for PB2 and EPC, in the range 10–120 μg/mL with good correlation coefficients (>0.996). For precision, the repeatability ranged from 1.89 to 3.23%, and the values for accuracy for PB2 and EPC were 95 and 89%, respectively. The LODs and LOQs for PB2 were 1.36 and 4.12 μg/mL, and for EPC were 2.18 and 6.61 μg/mL, respectively. The method was robust under the conditions employed. The proposed method could be employed for quality assessment of T. catigua, as well as pharmaceutical products.     

Simultaneous determination of cocaethylene and cocaine in blood by gas chromatography with surface ionization detection

Summary Cocaethylene together with cocaine spiked in human whole blood has been found measurable at high sensitivities by capillary gas chromatography with surface ionization detection. The drugs could be rapidly extracted by Sep-Pak C₁₈ cartridges with recovery of more than 60%. The calibration curves for both cocaethylene and cocaine using cocapropylene as internal standard were linear in the range 50–300 pmol mL⁻¹ of whole blood. The detection limits of cocaethylene and cocaine were 5–10 pmol mL⁻¹ (0.1–0.2 pmol on column if recovery is 100%). Cocaethylene could be determined for whole blood obtained from rats (ca. 200 g body wt.), which had received subcutaneous injection of 10 mg cocaine hydrochloride and 2.0 mL of 30% (v/v) ethanol 3 h before sampling; the mean levels of cocaethylene and cocaine were 101 and 1230 pmol mL⁻¹, respectively.     

Microwave induced plasma atomic emission spectrometry: a suitable detection system for the determination of volatile halocarbons

Microwave induced plasma atomic emission spectrometry (MIP-AES), a highly sensitive detection system for organometal compounds, was coupled to an automated purge and trap gas chromatographic system for the determination of volatile halogenated hydrocarbons in environmental water samples. Optimisation of the parameters affecting the injection and detection system led to relative detection limits from 1 to 14 ng · L^–1 for chlorine- and bromine-compounds and from 10 to 75 ng · L^–1 for iodine-compounds, on basis of a 10 mL sample volume. A comparison of the analytical characteristics between atomic emission detection (AED) and electron capture detection (ECD) showed a lower sensitivity of the atomic emission detector for halocarbons, but the detection thresholds are low enough to use the method for the determination of volatile halocarbons in trace level concentrations. The ability of the atomic emission detector provides increased selectivity for monitoring individual halogenated compounds under simplified and rapid chromatographic conditions, within a total analysis time of only 30 min. The method was applied with gas chromatographic separation for the analysis of sea water samples. Concentrations for the different elements between 0.05 and 15.28 μg · L^–1 were determined.     

Simultaneous determination of halogenated benz(a)anthracenes in water by HPLC with fluorometric detection

Summary A HPLC method using a fluorescence detector is described for the determination of halogenated benz(a)anthracenes (BAX, x=Cl or Br) in water. It consists of the following three procedures; (1) liquid-liquid extraction of BAX with benzene, (2) elimination of interfering compounds from the extracts by one dimensional dual-band thin layer chromatography, and (3) quantitative determination of BAX by HPLC equipped with a fluorescence detector. The recoveries of BAX from water samples through the entire analytical procedure amounted to more than 72%. The calibration curves for BAX were linear, e.g., with a range from 1 to 20 ng ml^–1 for 7-chlorobenz(a)anthracene (BACl). The lower detection limit for BACl was 20 pg for an injection volume of 20 l. This method has been applied to BAX in river water spiked with benz(a)anthracene [B(a)A] at 10 ng ml^–1 after chlorination. B(a)A, BACl and BABr were found in the levels of 2.01, 0.16 and 0.13 or less ng ml^–1, respectively.     

Specific and sensitive quantitation of 2,2'-dichlorodiethyl sulphide (sulphur mustard) in water, plasma and blood: application to toxicokinetic study in the rat after intravenous intoxication.

A sensitive and specific capillary gas chromatographic method has been developed to measure trace amounts of 2,2'-dichlorodiethyl sulphide (sulphur mustard) in environmental or biological samples. Sulphur mustard was isolated from water or plasma by a solid-phase extraction procedure and from blood by liquid-liquid extraction. The accuracy and precision of the methods were demonstrated using replicate analyses of spiked water, plasma or blood: within-run and between-run variabilities were less than 20%. These analytical methods were used to evaluate the rate of sulphur mustard degradation in water or plasma. Good linear calibration curves, with a detection limit of 45 ng/ml, were obtained for quantitation and determination of sulphur mustard in blood following its intravenous administration to rats. Initial toxicokinetic data were obtained.     

Poly(1‐butene)/clay nanocomposites: Preparation and properties

The preparation and properties of poly(1‐butene) (PB)/clay nanocomposites are described for the first time. Nanocomposites were prepared with the melt‐intercalation technique, using organically modified clay. The X‐ray diffraction patterns portrayed well‐defined diffraction peaks at higher d‐spacing than pristine clay, confirming the intercalation of polymer in silicate layers. Because PB exhibits time‐dependent polymorphism, the effect of clay on the phase transformation of PB was examined with thermal analysis. The phase transformation from a metastable tetragonal form to a stable hexagonal form was enhanced because of incorporation of layered silicates in the polymer matrix. The nanocomposites exhibited about a 40–140% increase in storage modulus depending on the clay content and significantly lower coefficient of thermal expansion. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1014–1021, 2003     

A sensitive gas chromatographic-tandem mass spectrometric method for detection of alkylating agents in water: application to acrylamide in drinking water,coffee and snuff

A sensitive analytical method for the analysis of acrylamide and other electrophilic agents in water has been developed. The amino acid L-valine served as a nucleophilic trapping agent. The method was applied to the analysis of acrylamide in 0.2-1 mL samples of drinking water or Millipore-filtered water, brewed coffee, or water extracts of snuff. The reaction product, N-(2-carbamoylethyl)valine, was incubated with pentafluorophenyl isothiocyanate to give a pentafluorophenylthiohydantoin (PFPTH) derivative. This derivative was extracted with diethyl ether, separated from excess reagent and impurities by a simple extraction procedure, and analyzed by gas chromatography-tandem mass spectrometry. (2H3)Acrylamide, added before the reaction with L-valine, was used as internal standard. Acrylamide and the related compound, N-methylolacrylamide, gave the same PFPTH derivative. The concentrations of acrylamides were < or = 0.4 nmol L(-1) (< or = 0.03 microg acrylamide L(-1)) in water, 200 to 350 nmol L(-1) in brewed coffee, and 10 to 34 nmol g(-1) snuff in portion bags, respectively. The precision (the coefficient of variation was 5%) and accuracy of the method were good. The detection limit was considerably lower than that of previously published methods for the analysis of acrylamide.     

Microanalysis of dialkylphosphorus metabolites of organophosphorus pesticides in human blood by capillary gas chromatography and by phosphorus-selective and ion trap detection

A procedure for the determination of dialkyphosphorus metabolites of organophosphorus pesticides in human blood has been worked out. Dimethyl and diethyl phosphates, phosphorothioates and phosphorodithioates, extracted with diethyl ether from plasma acidified with hydrochloric acid, were methylated with diazomethane and analysed by capillary gas chromatography with an alkali flame ionization detector and an ion trap detector. The extraction of metabolites was preceded by n-hexane extraction of parent organophosphorus pesticides without a negative effect on the efficiency of metabolite extraction. If plasma samples, containing 2 μ/ml of each metabolite, were not saturated with sodium chloride before extraction, only dialkyl phosphorothioates were recovered by more than 80%. The recoveries of other metabolites were less than 25%. The extraction of plasma samples saturated with sodium chloride resulted in higher recoveries of all metabolites. At concentrations ranging from 0.2 to 2.8 μg/ml the accumulation effeciencies (%±S.D.) of dimethyl and diethyl phosphorothioates were 92±20 and 97±11, and those of corresponding phosphorodithiotes 79±7 and 71±4. A significantly lower recovery (36±12%) was determined for dimethyl phosphate at concentrations in plasma below 2 μg/ml. The recovery of diethyl phosphate was dependent on the initial metabolite concentration in plasma being 31±5% at concentrations lower than 0.5 μg/ml, 51±12% at concentrations ranging from 0.7 to 1.7 μg/ml and 97±3% at concentrations at or above 2 μg/ml. Detection limits of metabolites in plasma using the phosphorus selective detector were 150 ng/ml for dimethyl phosphate and 50 ng/ml for other metabolites. Those values were for dialkyl phosphates and phophorothioates three to five times lower and for diakyl phosphorodithiotes even 30 times lower than detection limits achieved by the use of ion trap detector. The procedure was applied for the evidence and confirmation of human poisoning with organophosphorus pesticides.     

Synthesis and structure‐property relationship of new donor–acceptor‐type conjugated monomers and polymers on the basis of thiophene and benzothiadiazole

We have synthesized three new donor–acceptor‐type monomers to achieve soluble and processable low‐band gap polymers, 4,7‐bis(4‐octyl‐2‐thienyl)‐2,1,3‐benzothiadiazole (B4TB), 4,7‐bis(3‐octyl‐2‐thienyl)‐2,1,3‐benzothiadiazole (B3TB), and 4‐(3‐octyl‐2‐thienyl)‐7‐(4‐octyl‐2‐thienyl)‐2,1,3‐benzothiadiazole (B34TB), by the Suzuki coupling reaction. Using B4TB and B3TB, two soluble high molecular weight regioregular head‐to‐head and tail‐to‐tail polymers poly[4,7‐bis(4‐octyl‐2‐thienyl)‐2,1,3‐ benzothiadiazole] (PB4TB) and poly[4,7‐bis(3‐octyl‐2‐thienyl)‐2,1,3‐benzothiadiazole] (PB3TB) were prepared via iron(III) chloride‐mediated oxidative polymerization. The structures of the polymers were confirmed by ¹H and ¹³C NMR, and the molecular weights were determined by size exclusion chromatography. The optical properties (absorbance and fluorescence) of the monomers and polymers were studied and compared with unsubstituted analogues. The monomers and polymers bearing octyl substituents on the thiophene rings pointing away from the benzothiadiazole units (B4TB and PB4TB) possess a more planar structure, and their optical spectra appear redshifted as compared with those having the octyl chain nearer to the benzothiadiazole (B3TB and PB3TB). The optical band gaps of PB3BT (E_g = 2.01 eV) and PB4BT (E_g = 1.96 eV), however, are at much higher energy levels than that of the unsubstituted electrochemically polymerized PBTB material (E_g = 1.1–1.2 eV) as a result of steric effects of the octyl chains. The electrochemical properties of the monomers and polymers were examined using cyclic voltammetry and reflect the effect of alkyl substitution. B4TB and PB4TB were oxidized at a lower potential than B3TB and PB3TB, whereas their reduction potentials were less negative. The electrochemical band gap calculated from the onset of the reduction and oxidation process agreed with the optical band gap calculated from the absorption edges. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 251–261, 2002