The effect of magnetic fields on the electrodeposition of iron

The effect of a uniform magnetic field with flux density up to 1 T on the electrodeposition of Fe from sulphate electrolyte has been investigated under different field configurations relative to the electrode surface. Voltammetric and chronoamperometric experiments have been carried out coupled with an electrochemical quartz crystal microbalance for in situ mass change measurements. The structure and morphology of the deposited films were determined by scanning electron microscopy, atomic force microscopy and X-ray diffraction measurements. Results show that, when the magnetic field is applied parallel to the electrode surface, the limiting current density and the deposition rate are increased due to the magnetohydrodynamic effect. The nucleation process is also affected in parallel configuration; the current density of the maximum on the chronoamperograms is decreased, and an additional nucleation step might be observed. This effect is attributed to the hydrodynamic response of the electrochemical system. No significant influence on the electrochemical reaction was observed when a magnetic field was applied perpendicular to the electrode. But in this configuration, the morphology of deposited layers is changed by the magnetic field. The morphology changes are discussed. No effect of the magnetic field on the crystallographic structure was observed.     

Vertical motion of a charged colloidal particle near an AC polarized electrode with a nonuniform potential distribution: theory and experimental evidence

Electroosmotic flow in the vicinity of a colloidal particle suspended over an electrode accounts for observed changes in the average height of the particle when the electrode passes alternating current at 100 Hz. The main findings are (1) electroosmotic flow provides sufficient force to move the particle and (2) a phase shift between the purely electrical force on the particle and the particle's motion provides evidence of an E2 force acting on the particle. The electroosmotic force in this case arises from the boundary condition applied when faradaic reactions occur on the electrode. The presence of a potential-dependent electrode reaction moves the likely distribution of electrical current at the electrode surface toward uniform current density around the particle. In the presence of a particle the uniform current density is associated with a nonuniform potential; thus, the electric field around the particle has a nonzero radial component along the electrode surface, which interacts with unbalanced charge in the diffuse double layer on the electrode to create a flow pattern and impose an electroosmotic-flow-based force on the particle. Numerical solutions are presented for these additional height-dependent forces on the particle as a function of the current distribution on the electrode and for the time-dependent probability density of a charged colloidal particle near a planar electrode with a nonuniform electrical potential boundary condition. The electrical potential distribution on the electrode, combined with a phase difference between the electric field in solution and the electrode potential, can account for the experimentally observed motion of particles in ac electric fields in the frequency range from approximately 10 to 200 Hz.     

Electropolymerized coatings of polyaniline on copper by using the galvanostatic method and their corrosion protection performance in HCl medium

The synthesis of polyaniline coatings on the copper (Cu) surface has been investigated by using the galvanostatic method. The synthesized coatings were characterized by Fourier transform infrared spectroscopy, UV–visible absorption spectrometry and scanning electron microscopy. The anticorrosion performances of polyaniline coatings were investigated in 0.5 M HCl medium by the potentiodynamic polarization technique and electrochemical impedance spectroscopy. The corrosion rate of polyaniline‐coated Cu was found to be ～27 times lower than bare Cu, and potential corrosion increased from ?0.21 V versus Ag/AgCl for uncoated Cu to ?0.19 V versus Ag/AgCl for polyaniline‐coated Cu electrodes. Electrochemical measurements indicate that polyaniline coating has good inhibiting properties with a mean efficiency of ~96% at 10 mAcm^?2 current density applied on Cu corrosion in acid media. The results of this study clearly ascertain that the polyaniline has an outstanding potential to protect Cu against corrosion in an acidic environment. Copyright © 2014 John Wiley & Sons, Ltd.     

Role of magnetic forces in electrochemical reactions at microstructures

The effect of an external magnetic field (up to 0.8 T) on the anodic dissolution of microstructures has been investigated systematically. Copper and silver wires (100 microm in diameter) were embedded in epoxy resin and dissolved potentiostatically while a magnetic field was periodically switched on and off. A special feature of the thus prepared structures is that they show a smooth transition from an inlaid disk to a recessed disk electrode. An increase or a decrease of the limiting current density in the presence of B was found depending on the orientation of the magnetic field and the hydrodynamic conditions in the cell (natural or forced convection). The magnetic forces which are responsible for this are the Lorentz force and the gradient force. We propose a model which discusses the interaction of these forces with the natural and the forced convection to explain the experimental results.     

Local electrochemical studies of the microstructural corrosion of AlCu4Mg1 as-cast aluminium alloy and influence of applied strain

The microstructure of AlCu4Mg1 as-cast aluminium alloy was first determined by means of field emission-scanning electron microscope with an integrated electron dispersion spectrometer, secondary ion mass spectroscopy and atomic force microscopy. Large precipitates (Al₂Cu, Al–Si–Mn–Fe–Cu, oxides) were located at grain boundaries, whereas small particles (aluminium, magnesium and copper) were present in grains. The electrochemical response and pitting susceptibility of sites containing precipitates were then investigated after polishing using the electrochemical microcell technique. After straining, big scattering was observed in the electrochemical response. The most active places corresponded to the sites containing wide microcracks and severe damages in the matrix. In this case, the corrosion potential was around −1,000 mV vs. Ag/AgCl, and the current in the passive domain was five times higher than on the strained matrix. In the absence of severe damage in the matrix or wide microcracks, the corrosion potential was more anodic and the current density in the passive range was around 0.5 mA cm⁻². Local polarisation curves carried out in sites containing large precipitates and no defects induced by straining were very close to those obtained in grains far from precipitates.     

Magnetic field effect on electrochemical oscillations during iron dissolution

A fairly low magnetic field of ca. 30 mT was found to affect the period and the amplitude of the self-sustained current oscillation of an iron electrode. This was observed much distinctively when the direction of the applied field was normal to the electrode surface, i.e., non-magnetohydrodynamic (MHD) configuration. The Flade potential of the iron electrode was not affected by the magnetic field intensity of up to 4 T. The observed magnetic field effect was attributed to the depression of the natural convection in the vicinity of the electrode surface which was caused by the two local paramagnetic body forces, the magnetic field gradient force and/or the concentration gradient force.     

Processing of nanoporous Ag layers by potential-controlled displacement (PCD) of Cu

A cementation-like process taking place under potential control and introduced in this work as a "potential-controlled displacement" (PCD) is developed as a new method for processing of nanoporous Ag structures with controlled roughness (porosity) length scales. Most of the development work is done in a deoxygenated electrolyte containing 1 x 10(-3) M AgClO(4 )+ 5 x 10(-2) M CuSO(4) + 1 x 10(-1) M HClO(4) using a copper rotating disk electrode at 50 rpm. At this electrolyte concentration, the Ag deposition is under diffusion limitations whereas the Cu dissolution displays a typical Butler-Volmer anodic behavior. Thus, a careful choice of the operational current density enables strict control of the ratio between the dissolving and depositing metals as ascertained independently by atomic absorption spectrometry (AAS). The roughness length scale of the resulting surfaces is controlled by a careful selection of the current density applied. The highest surface area and finest morphology is obtained when the atomic ratio of Ag deposition and Cu dissolution becomes 1:1. Preseeding of uniform Ag clusters on the Cu surface made by pulse plating of Ag along with complementary plating and stripping of Pb monolayer is found to yield finer length scale resulting in up to a 67% higher surface area. An electrochemical technique using as a reference value the charge of an underpotentially deposited Pb layer on a flat Ag surface is used for measuring the real surface area. Scanning electron microscopy (SEM) studies are conducted to examine and characterize the deposit morphology of Ag grown by PCD on Cu substrates.     

Atomistic insights into aqueous corrosion of copper

Corrosion is a fundamental problem in electrochemistry and represents a mode of failure of technologically important materials. Understanding the basic mechanism of aqueous corrosion of metals such as Cu in presence of halide ions is hence essential. Using molecular dynamics simulations incorporating reactive force-field (ReaxFF), the interaction of copper substrates and chlorine under aqueous conditions has been investigated. These simulations incorporate effects of proton transfer in the aqueous media and are suitable for modeling the bond formation and bond breakage phenomenon that is associated with complex aqueous corrosion phenomena. Systematic investigation of the corrosion process has been carried out by simulating different chlorine concentration and solution states. The structural and morphological differences associated with metal dissolution in the presence of chloride ions are evaluated using dynamical correlation functions. The simulated atomic trajectories are used to analyze the charged states, molecular structure and ion density distribution which are utilized to understand the atomic scale mechanism of corrosion of copper substrates under aqueous conditions. Increased concentration of chlorine and higher ambient temperature were found to expedite the corrosion of copper. In order to study the effect of solution states on the corrosion resistance of Cu, partial fractions of proton or hydroxide in water were configured, and higher corrosion rate at partial fraction hydroxide environment was observed. When the Cl(-) concentration is low, oxygen or hydroxide ion adsorption onto Cu surface has been confirmed in partial fraction hydroxide environment. Our study provides new atomic scale insights into the early stages of aqueous corrosion of metals such as copper.     

Inhibition of copper corrosion in acidic sulphate media by eco-friendly amino acid compound

This investigation aimed to study a “green” non-toxic biodegradable copper corrosion inhibitor in an acidic sodium sulphate solution. The methods used in the investigation of cysteine as a copper corrosion inhibitor in an acidic sodium sulphate solution were: potentiodynamic measurements, open circuit potential measurements, and chronoamperometric measurements. Optical microscopy was used in addition to electrochemical methods. Potentiodynamic measurements show that cysteine has good inhibitory properties in an acidic medium. Polarisation curves indicate that the presence of cysteine in a sulphate solution decreases the current density and that using various cysteine concentrations results in the formation of a protective film on the surface of the electrode due to the formation of the Cu(I)-cys complex. These results are confirmed by chronoamperometric measurements. Furthermore, it is clear from microphotographs that a protective film does form on copper electrode in the presence of cysteine. The Langmuir adsorption isotherm indicates that cysteine is chemisorbed on the surface of the electrode.     

Magnetic field effects on the open circuit potential of ferromagnetic electrodes in corroding solutions

Magnetic fields shift the open circuit potential (OCP) of ferromagnetic electrodes (Fe, Co, and Ni) in corroding solutions. The OCP changes we observe (a) follow the series Fe>Co>Ni; (b) increase with the magnetic flux density; (c) reach a maximum with disk electrodes approximately 1 mm in diameter; and (d) depend on the orientation of the electrode. We report that when the surface of the electrode is oriented parallel (theta = 90 degrees) or perpendicular (theta = 0 degrees) to the magnetic field, the open circuit potential moves in opposite directions (positive and negative, respectively) with the largest changes occurring when the electrode surface is parallel to the magnetic field. Nonconvective sleeve electrodes produce the same behavior. The overall experimental evidence suggests that the magnetic field changes the OCP by modifying the surface concentrations of the paramagnetic participants in the corrosion process of the ferromagnetic electrode by species in solution; this in turn is accomplished by imposing a field-gradient driven mode of mass transfer upon paramagnetic species in solution (magnetophoresis). Simulations of the magnetic field around the ferromagnetic electrode at the two extreme orientations considered here show that in one case (theta = 90 degrees) field gradients actually repel, while in the other case (theta = 0 degrees) they attract paramagnetic species in the vicinity of the electrode.     

弱碱性介质中氯离子对铜电极腐蚀行为的影响

应用循环伏安法、X射线光电子能谱法、电化学阻抗谱法以及现场椭圆偏光法研究了在弱碱性介质中添加Cl－对铜电极腐蚀行为的影响.结果表明, Cl－的加入能加剧铜电极的腐蚀,使腐蚀电流以及现场椭圆偏振参数Δ的变化范围都增大1个数量级, Cl－对Cu2O的掺杂将使铜电极的表面膜变得疏松,膜的耐蚀性变差.椭圆偏光实验不仅与电化学和能谱实验的结果一致,而且还能定性地、清楚地分辨出铜电极腐蚀过程中Cu2O的生成、Cl－对Cu2O的掺杂、CuO的生成等不同阶段;同时,利用恰当的模型还能定量地确定各个阶段铜电极表面膜的组成、厚度的变化,从而为研究铜电极的腐蚀与防护机理提供更多有用信息.     

缺陷石墨烯吸附Au、Ag、Cu的第一性原理计算

采用基于密度泛函理论的投影缀加波方法研究了Au、Ag、Cu吸附在缺陷石墨烯单侧和双侧的体系,对吸附体系的吸附能、磁性、电荷转移和电子结构进行了计算和分析.缺陷石墨烯吸附Au、Ag、Cu体系的吸附能比本征石墨烯增加2 eV以上,说明三种金属原子更容易吸附在缺陷位置;吸附体系的电荷密度差分和电子结构的结果表明,Au、Ag、Cu与缺陷石墨烯之间均为化学吸附.计算吸附体系的磁性发现,单侧吸附时三种吸附体系均有磁性,磁矩大约为1μB;双侧吸附时,三种吸附体系磁矩大约为2μB.     

Impact of Top Electrodes (Cu,Ag, and Al) on Resistive Switching behaviour of Cu-rich Cu2ZnSnS4 (CZTS) Ideal Kesterite

Cu₂ZnSnS₄ (CZTS) active material-based resistive random-access memory (RRAM) devices are investigated to understand the impact of three different Cu, Ag, and Al top electrodes. The dual resistance switching (RS) behaviour of spin coated CZTS on ITO/Glass is investigated up to 10² cycles. The stability of all the devices (Cu/CZTS/ITO, Ag/CZTS/ITO, and Al/CZTS/ITO) is investigated up to 10³ sec in low- (LRS) and high- (HRS) resistance states at 0.2 V read voltage. The endurance up to 10² cycles with 30 msec switching width shows stable write and erase current. Weibull cumulative distribution plots suggest that Ag top electrode is relatively more stable for set and reset state with 33.61 and 25.02 shape factors, respectively. The charge carrier transportation is explained by double logarithmic plots, Schottky emission plots, and band diagrams, substantiating that at lower applied electric field intrinsic copper ions dominate in Cu/CZTS/ITO, whereas, at higher electric filed, top electrodes (Cu and Ag) dominate over intrinsic copper ions. Intrinsic Cu⁺ in CZTS plays a decisive role in resistive switching with Al electrode. Further, the impedance spectroscopy measurements suggest that Cu⁺ and Ag⁺ diffusion is the main source for the resistive switching with Cu and Ag electrodes.     

Redox magnetohydrodynamic enhancement of stripping voltammetry: toward portable analysis using disposable electrodes, permanent magnets, and small volumes

The use of redox magnetohydrodynamics (MHD) to enhance the anodic stripping voltammetry (ASV) response of heavy metals has been investigated, with respect to achieving portability: disposable electrodes consisting of screen-printed carbon (SPC) on a low temperature co-fired ceramic (LTCC) substrate, small volumes, and permanent magnets. The analytes tested (Cd(2+), Cu(2+), and Pb(2+)) were codeposited on SPC with Hg(2+) to form a Hg thin film electrode. High concentrations of Fe(3+) were used to produce a high cathodic current which generates a significant Lorentz force in the presence of a magnetic field. This Lorentz force induces solution convection during the deposition step, enhancing the mass transport of analytes to the electrode and increasing their preconcentrated quantity in the mercury thin film. Therefore, larger ASV peaks and improved sensitivities are obtained, compared to analyses performed without a magnet. The effects on ASV signal of varying Hg(2+) concentration (0.10 and 1.0 mM), deposition time (10-600 s), and electrode surface roughness were investigated. In addition, analyses were performed using a real lake water matrix. By using the disposable LTCC-SPC working electrodes in small volumes (150 microL) and with small permanent magnets (0.78 T), peak areas were increased by 75% when compared to the signal obtained in the absence of a magnetic field. A limit of detection of 25 nM for Cd(2+) was observed with only a 1 min preconcentration time.     

A comparative evaluation on the anodic behavior of Cu and Ag electrodes in non-aqueous fluoride and fluoroborate media

The voltammetric responses of copper and silver had been extensively studied and compared in a variety of non-aqueous solvents such as acetonitrile (AN), propylene carbonate (PC) and sulfolane containing two different supporting electrolytes namely triethylaminetrishydrogen fluoride (TEA.3HF) and tetrabutylammonium tetrafluoroborate (TBABF₄). The dissolution rate and surface transformation on the electrode surfaces as a result of anodic polarization was investigated using atomic absorption spectroscopy (AAS) and scanning electron microscopy (SEM), respectively. In solvent-free TEA.3HF medium, the copper electrode shows high charge recovery ratio (Q _c/Q _a), and the difference between the initial anodic and cathodic potentials, obtained at a current density of 2 mA cm⁻², is around 0.11 V, suggesting that in this medium, Cu can certainly serve as reference electrode. On the other hand, on Ag electrode, substantial dissolution was observed leading to very high anodic (Q _a) and cathodic (Q _c) charges, and the surface morphology after the cyclic polarization results in roughened surface with large pores. The effects of incorporating AN and water as additives in TEA.3HF on the solubility and stability of these metal fluoride films are also reported. The dissolution pattern and film formation behavior of these two metals in the different solvents containing fluoride and fluoroborate ionic species have several qualitative similarities, as noted from cyclic voltammetry responses and SEM morphology. Anodic dissolution and precipitation process for both Cu and Ag depends significantly on the nature of supporting electrolytes as well as solvents. In AN containing 0.1 M TEA.3HF, the dissolution of Cu and Ag electrodes was very high. Fluoride salts of Cu show lesser solubility than Ag in those solvents, while fluoroborate salts exhibit the reverse trend. The AAS data suggest that for a particular salt, which may be either fluoride or fluoroborate of Cu and Ag, the relative solubility decreases in the order AN > PC > sulfolane.     

邻碘苯甲酸电还原脱碘的原位红外光谱研究

采用循环伏安法研究了邻碘苯甲酸在NaOH溶液中的电化学还原反应,与Pt和Ti等电极相比,Ag和Cu电极对邻碘苯甲酸具有较好的电还原活性,还原电位向正电位方向移动.通过原位红外光谱技术研究了邻碘苯甲酸在Ag和Cu电极上的电还原机理.结果表明,在电位高于-800 mV时,邻碘苯甲酸在Ag电极表面先形成吸附中间态R…I…Ag,而在Cu电极表面以负离子形式存在.随着电位的进一步负移,邻碘苯甲酸在Ag和Cu电极上均发生脱碘加氢反应,经还原得到最终产物苯甲酸.     

缺陷石墨烯吸附Au、Ag、Cu的第一性原理计算

采用基于密度泛函理论的投影缀加波方法研究了Au、Ag、Cu吸附在缺陷石墨烯单侧和双侧的体系,对吸附体系的吸附能、磁性、电荷转移和电子结构进行了计算和分析. 缺陷石墨烯吸附Au、Ag、Cu体系的吸附能比本征石墨烯增加2 eV以上,说明三种金属原子更容易吸附在缺陷位置;吸附体系的电荷密度差分和电子结构的结果表明,Au、Ag、Cu与缺陷石墨烯之间均为化学吸附. 计算吸附体系的磁性发现,单侧吸附时三种吸附体系均有磁性,磁矩大约为1μ_B;双侧吸附时,三种吸附体系磁矩大约为2μ_B.     

Hydrogen evolution kinetics on Ni cathodes modified by spontaneous deposition of Ag or Cu

Nickel modification by spontaneous deposition of transition metals such as Ag and Cu is shown as an economic and simple alternative for the activation of hydrogen evolution reaction(HER) on cathodes in alkaline media. The kinetics of HER is studied on Ni/Ag and Ni/Cu catalysts by cyclic voltammetry and electrochemical impedance spectroscopy(EIS) using a rotating disk electrode(RDE). Freshly synthesized catalysts, as well as catalysts subjected to a short chronoamperometric ageing procedure, are analyzed and the kinetic and thermodynamic parameters of the HER are obtained. The nickel surface modified with transition metals with an outer shell electronic configuration [xd~(10)(x+1)s~1], such as Cu(3d~(10)4s~1)and Ag(4d~(10)5s~1), shows an improved activity for the HER compared to bare nickel. Furthermore, the Ni/Cu catalyst presents a decreased onset potential. The hydrogen evolution rate, measured as current density at –1.5 V(vs. SCE), is similar on Ni/Cu and Ni/Ag electrodes.     

Measurement of hypoiodous acid concentration by a novel type iodide selective electrode and a new method to prepare HOI. Monitoring HOI levels in the Briggs-Rauscher oscillatory reaction

A new type of iodide selective electrode prepared by dipping a silver wire into molten silver iodide is reported. The electrode was calibrated for silver and iodide ions and the measured electromotive force for various Ag(+) and I(-) concentrations was close to the theoretical within a few millivolts. Besides Ag(+) and I(-) ions, however, the electrode also responds to hypoiodous acid. Thus, the electrode was calibrated for HOI as well, and for that purpose a new method of hypoiodous acid preparation was developed. To explain the close to Nernstian electrode response for HOI and also the effect of hydrogen ion and iodine concentration on that response, the corrosion potential theory suggested earlier by Noszticzius et al. was modified and developed further. Following oscillations in the Briggs-Rauscher reaction with the new electrode the potential crosses the "solubility limit potential" (SLP) of silver iodide. Potentials below SLP are controlled by the concentration of I(-), but potentials above SLP are corrosion potentials determined by the concentration of HOI. Finally, the measured HOI oscillations are compared with calculated ones simulated by a model by Furrow et al.     

电化学方法固定CO2用于2-羟基-2-(4-甲氧基苯基)-丙酸甲酯的合成

在一室型电解池中, 以饱和CO₂的N,N-二甲基甲酰胺(DMF)为溶液, Mg为牺牲阳极, 不锈钢、钛、铜、镍和银为工作电极, 通过电化学方法固定CO₂, 在恒电流电解的条件下研究了对甲氧基苯乙酮的电羧化反应, 得到了重要的有机合成中间体2-羟基-2-(4-甲氧基苯基)-丙酸甲酯. 电羧化产率受支持电解质种类、电极材料、电流密度、电解电量和反应温度等影响. 经过反应条件的优化, 目标产物在恒定电流密度为5.0 mA/cm²的条件下产率达到63%. 同时, 以玻碳电极-Pt丝螺旋电极-Ag/AgI/I^-为三电极体系, 研究了对甲氧基苯乙酮的电化学行为, 根据底物在通入CO₂前后循环伏安图的变化推测了对甲氧基苯乙酮的电羧化反应机理.