以PEO-b-PAN嵌段共聚物胶束作模板合成SiO_2-C纳米复合材料

通过阴离子聚合和活性自由基聚合相结合的方法,合成了聚环氧乙烷-聚丙烯腈两亲性嵌段共聚物(PEO-b-PAN).PEO-b-PAN嵌段共聚物在水溶液中自组装形成胶束正硅酸乙酯以胶束作模板进行溶胶-凝胶过程,形成SiO2/PEO-b-PAN复合材料.随后经300℃预氧化,1000℃高温炭化,得到SiO2-C纳米复合材料.用1HNMR、IR、GPC、TGA、TEM、SEM等技术对嵌段共聚物及SiO2-C纳米复合材料进行了表征,结果表明SiO2-C复合材料的结构为SiO2为壳C为核的纳米粒子,粒子的直径为(55±5)nm.     

不同制备方法和反应条件对Fe_2O_3形貌和晶型转变的影响

研究了吸附相反应技术、浸渍法以及沉淀法制备Fe2O3的过程中,反应环境的变化对粒子形貌和晶型转变过程的影响。当吸附层是主要反应场所时,生成的粒子与SiO2表面以较强的化学键键合,焙烧过程中Fe2O3的晶型变化和粒子团聚被有效地抑制,焙烧后Fe2O3粒子维持稳定的γ-Fe2O3晶型和高分散的小粒子。而在乙醇体相中反应生成的粒子,仅通过物理作用与SiO2表面结合,不能有效抑制其向α-Fe2O3晶型的转变和粒子的团聚。吸附相反应制备过程中,当水量持续增加或者体系温度升高,反应环境逐渐从吸附层向乙醇体相中转变,SiO2对Fe2O3晶型转变的抑制作用减弱,从而导致样品中逐渐出现α-Fe2O3晶型。     

电解质诱导聚集初级粒子制备介孔SiO_2材料

在无模板剂的条件下,通过在Stber合成过程中引入外加电解质成功地制备了具有介孔结构的SiO2粒子.实验结果表明,通过电解质的加入可以诱导Stber过程中初级SiO2粒子的聚集,从而得到了具有介孔结构和较强表面吸附能力的SiO2粒子.     

ZrO2中空微球的模板法制备及吸附性能研究

以油菜花粉为生物模板,通过温和易控的水浴-陈化法制备了纳/微米结构ZrO2中空微球.利用扫描电子显微镜(SEM)、红外光谱(FTIR)、X射线能谱(EDS)、X射线衍射(XRD)、比表面孔隙度分析、热分析等对所制备的产物和前驱体进行了表征,并对产物的吸附性能进行了初步的研究.结果表明,ZrO2中空微球的球壳由纳米粒子构筑并形成介孔结构.花粉模板前处理方式不同,其模板作用不同,可以获得两种不同球壳厚度、表面形貌和比表面积的ZrO2中空微球.其中"镂空"结构的ZrO2微球对铬黑T有良好的吸附性能.对ZrO2中空结构形成的机理进行了分析和讨论.     

Template Synthesis and Adsorption of Hollow Zr02 Microspheres

以油菜花粉为生物模板,通过温和易控的水浴-陈化法制备了纳/微米结构ZrO2中空微球.利用扫描电子显微镜（SEM）、红外光谱（FTIR）、X射线能谱（EDS）、X射线衍射（XRD）、比表面孔隙度分析、热分析等对所制备的产物和前驱体进行了表征,并对产物的吸附性能进行了初步的研究.结果表明,ZrO2中空微球的球壳由纳米粒子构筑并形成介孔结构.花粉模板前处理方式不同,其模板作用不同,可以获得两种不同球壳厚度、表面形貌和比表面积的ZrO2中空微球.其中＂镂空＂结构的ZrO2微球对铬黑T有良好的吸附性能.对ZrO2中空结构形成的机理进行了分析和讨论.     

辛醇改性纳米二氧化硅表面的研究

纳米粒子由于粒径小,所以具有很高的比表面积,表面原子处于高度活化状态,使得表面能很高,粒子易于团聚,填充未经表面处理的纳米粒子,不但起不到特殊作用,反而会成为复合材料的力学弱点。所以要对纳米粒子进行表面改性,提高分散性,增加纳米粒子与聚合物间的界面结合力。用醇类对许多粉体进行酯化反应是常用的表面改性方法。金属氧化物与醇的反应是酯化反应[1]。酯化反应修饰法对于表面为弱酸性和中性的纳米粒子最为有效,例如SiO2等。醇的羟基与SiO2的表面羟基发生反应脱掉一分子水,达到表面接枝的目的。方程式为:这样R基团接枝到SiO2的表面,由于R基团是亲油性的,从而增加了极性的SiO2纳米粒子与有机物的润湿性。为了推动反应正向进行,关键在于及时将产生的水份引出反应体系。目前国内外用醇对纳米粒子进行表面改性主要采用常规回流法和高压反应釜法[2]。由于微波照射具有对物质高效、均匀的加热作用,同时还具有电磁场对反应分子间行为的直接作用而引起的所谓“非热效应”,所以本实验采用微波照射法用正辛醇对SiO2纳米微粒进行表面酯化反应并与常规回流法进行比较。关于该方面的研究报道国内外较少。1实验部分1.1实验原料纳米SiO2:(10~20nm...     

新型球形纳米空心SiO2的模板合成方法研究

以纳米碳酸钙颗粒为新颖的无机模板剂,硅酸钠为无机硅源,通过溶胶-凝胶法形成CaCO3／SiO2的核壳结构;随后通过高温煅烧、酸溶和干燥处理,合成出了具有高比表面积的球形纳米空心二氧化硅粒子．然后,分别采用TEM,SEM,EDS,XRD,FTIR和TG等测试手段对样品进行了分析和表征,并考察了不同合成条件,如反应温度、反应pH值、煅烧温度和包覆反应时SiO2／CaCO3的配比对纳米空心二氧化硅粒子的比表面积变化．实验结果表明：较高的反应温度如60～80℃,pn值9左右、SiO2包覆量为碳酸钙质量的10％,以及煅烧温度为700℃,有利于形成空心形貌较好、比表面较大的球形纳米空心二氧化硅。     

制备方法对模板法制备SiO_2中空微球形貌的影响

模板法是制备无机中空微球的重要方法之一.首先通过苯乙烯和甲基丙烯酸的无皂乳液聚合法制得表面含羧基、粒径为360nm的单分散聚苯乙烯(PSt)乳胶粒,并以此为模板,分别采用表面改性-前驱体水解法(PHC)和SiO2纳米颗粒层层自组装法(LBL),制备出了不同壳层厚度的PSt/SiO2核壳结构复合微球,然后经500℃煅烧4h,得到SiO2中空微球.利用透射电镜和扫描电镜对微球结构形态进行了表征.研究表明,首先利用γ-氨丙基三乙氧基硅烷(KH-550)对PSt模板微球进行表面改性、然后再在乙醇-水混合介质中进行原硅酸乙酯(TEOS)水解与缩合反应的PHC法,是制备PSt/SiO2核壳结构复合微球的简便方法,复合微球经煅烧可制得表面均匀、结构致密、壳层厚度和形貌可控的SiO2中空微球;而LBL法制备PSt/SiO2核壳结构复合微球的工艺复杂,煅烧后所得SiO2中空微球结构疏松,易于破碎.     

磁性SiO2/PSt中空复合微球的细乳液法制备及表征

采用双原位细乳液聚合工艺,将疏水改性的磁性纳米粒子(MNP)加入到细乳液反应体系的油相中,利用增长的聚合物和单体TEOS之间的相分离原理,实现了聚合物的生成和TEOS的水解缩合同步进行,一步获得了磁性SiO2/PSt中空复合微球.通过红外光谱(FTIR)、透射电镜(TEM)、热重差热分析(TGA/DSC)和振动磁强计(VSM)对中空复合微球进行了表征.结果表明,制备的SiO2/PSt中空复合微球的尺寸范围为300～600 nm,当加入磁性纳米粒子后,得到的磁性SiO2/PSt中空微球保持了原来的中空结构,中空复合微球内腔的大小可以通过改变单体TEOS的加入量来控制.SiO2/PSt中空微球对磁性纳米粒子的包封率达到了86%.磁性SiO2/PSt中空复合微球具有超顺磁性,饱和磁强度值为14.7 emu/g.     

疏水高分子介导可动芯SiO2杂化纳米粒子的仿生合成

在疏水高分子胶体模板——含氟丙烯酸酯(FA)共聚物乳胶粒中引入能够介导SiO2原位沉积的聚胺催化活性点-甲基丙烯酰氧乙基三甲基氯化铵(DMC),以四甲氧基硅烷(TMOS)为硅源,在环境条件下可控合成了核壳型FA共聚物/SiO2杂化纳米粒子.高温煅烧除去聚合物核质,可得到中空的SiO2纳米粒子,结合FTIR、EDX、TGA以及XPS等表征数据印证了SiO2的沉积主要发生在聚合物模板的表面.进一步考察了反应条件,如聚胺功能单体DMC的浓度、TMOS的浓度以及反应时间对SiO2杂化纳米粒子的形貌与组成的影响.实验结果表明增加DMC或者TMOS的浓度,适当延长反应时间,均可增加SiO2粒子的沉积速率,导致SiO2壳层的厚度增加,并且杂化粒子的形貌由凹陷多褶皱的核壳结构向可动芯结构转变.由于FA共聚物模板的强疏水性,增加有机核层和无机壳层间的不相容排斥,最终导致核壳层间空腔的形成,得到含可动芯的核壳型SiO2杂化粒子.     

新型球形纳米空心SiO2的模板合成方法研究

以纳米碳酸钙颗粒为新颖的无机模板剂, 硅酸钠为无机硅源, 通过溶胶-凝胶法形成CaCO₃/SiO₂的核壳结构; 随后通过高温煅烧、酸溶和干燥处理, 合成出了具有高比表面积的球形纳米空心二氧化硅粒子. 然后, 分别采用TEM, SEM, EDS, XRD, FTIR和TG等测试手段对样品进行了分析和表征, 并考察了不同合成条件, 如反应温度、反应pH值、煅烧温度和包覆反应时SiO₂/CaCO₃的配比对纳米空心二氧化硅粒子的比表面积变化. 实验结果表明: 较高的反应温度如60～80 ℃, pH值9左右、SiO₂包覆量为碳酸钙质量的10%, 以及煅烧温度为700 ℃, 有利于形成空心形貌较好、比表面较大的球形纳米空心二氧化硅.     

Reverse Atom Transfer Radical Polymerization of MMA in the Presence of CaCO3/SiO2 Two-Component Composite Particles

Summary: We previously discovered that structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, can be achieved via reverse atom transfer radical polymerization (ATRP), using 2,2′-azo-bis-isobutyronitrile as initiator and Cu^II bromide as catalyst. In the present study, the influence of the mass ratio of CaCO₃/SiO₂ two-component composite particles to methyl methacrylate (MMA) on the rate and behavior of the polymerization was studied in detail. The results illustrate that increasing the mass ratio of CaCO₃/SiO₂ two-component composite particles will decrease the overall rate of polymerization of MMA under standard reverse ATRP conditions. Thermal properties of the obtained well-defined particles were characterized and determined by thermogravimetric analysis (TGA). The results indicate that well-defined PMMA chains grafted on the surface of CaCO₃/SiO₂ particles were only degraded by random chain scission of C C linkages within the PMMA chain, which is different from the degradation of PMMA chains prepared via traditional radical polymerization. This difference is reasonably ascribed to the difference between the end groups of PMMA prepared via reverse ATRP and that via traditional radical polymerization, which has been confirmed by end group analysis measured by ¹H–NMR spectroscopy.     

Synthesis and characterization of well-defined poly(methyl methacrylate)/CaCO3/SiO2 three-component composite particles via reverse atom transfer radical polymerization

The attempt to prepare structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, via reverse atom transfer radical polymerization (ATRP), using 2-2′-azo-bis-isobutyronitrile as initiator and Cu(II) bromide as catalyst was reported. CaCO₃/SiO₂ two-component composite particles were first obtained through sol–gel method, and their morphology and surface element information were determined by transmission electron microscopy and X-ray photoelectron spectroscopy, respectively. The results indicate that the CaCO₃ was encapsulated by the obtained SiO₂. After being modified by silane coupling agent, the CaCO₃/SiO₂ composite particles copolymerized with methyl methacrylate (MMA) under standard reverse ATRP conditions to produce PMMA/CaCO₃/SiO₂ three-component composite particles. In the case concerned, first-order kinetic plots and linear increase of molecular weight (Mn) vs conversion and narrow molecular weight distribution for the graft polymer samples were observed. Furthermore, the gel permeation chromatography results illustrated that both the free PMMA chains from the solvent and the graft PMMA chains from the surface of CaCO₃/SiO₂ two-component composite particles were growing at the same rate. Characterizations of the PMMA-grafted CaCO₃/SiO₂ composite particles were done by Fourier transform infrared and thermogravimetric analysis. The results showed that the surface of the modified inorganic particles was grafted by the MMA and that the grafting percentage was about 8.7%.     

Fabrication of anisotropic silica hollow microspheres using polymeric protrusion particles as templates

Anisotropic polystyrene/poly(styrene-co-divinylbenzene) (PS/P(S-DVB)) protrusion particles with various morphologies such as eyeball-like, snowman-like, and raspberry-like were synthesized using a modified seeded polymerization method by dynamically controlling and stabilizing the phase separation. The effects of swelling agent, crosslinker, and monomer concentrations on the particle morphologies were studied. Using the PS/P(S-DVB) protrusion particles as templates, anisotropic silica (SiO₂) hollow microspheres were fabricated facilely. The obtained anisotropic silica hollow spheres had a potential application in rapid waste removal and detoxification extraction with a very simple procedure.     

Preparation of poly(methyl methacrylate)/CaCO3/SiO2 composite particles via emulsion polymerization

A novel method to prepare organic/inorganic composite particles, i.e. poly(methyl methacrylate)/CaCO₃/SiO₂ three-component composite particles, using emulsion polymerization of methyl methacrylate with sodium lauryl sulfate as a surfactant in an aqueous medium was reported. CaCO₃/SiO₂ two-component inorganic composite particles were obtained firstly by the reaction between Na₂CO₃ and CaCl₂ in porous silica (submicrometer size) aqueous sol and the specific surface area of the particles was measured by the Brunauer–Emmett–Teller (BET) method. The results show that the BET specific surface area of the CaCO₃/SiO₂ composite particle is much smaller than that of the silica particle, indicating that CaCO₃ particles were adsorbed by porous silica and that two-component inorganic composite particles were formed. Before copolymerization with methyl methacrylate, the inorganic composite particles were coated with a modifying agent through covalent attachment. The chemical structures of the poly(methyl methacrylate)/CaCO₃/SiO₂ composite particles obtained were characterized by Fourier transform IR spectroscopy and thermogravimetric analysis. The results show that the surface of the modified inorganic particles is grafted by the methyl methacrylate molecules and that the grafting percentage is about 15.2%.     

Nano-silica and SiO2/CaCO3 nanocomposite prepared from semi-burned rice straw ash as modified papermaking fillers

Silica (SiO₂) nanoparticles and silica/calcium carbonate (SiO₂/CaCO₃) core–shell nanocomposites were prepared by sol–gel technique as fillers for papermaking application. Semi-burned rice straw ash (SBRSA), as waste material, was used to prepare the targeted fillers. Preparation of SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites was carried out using Na₂SiO₃ solution that was prepared from SBRSA and CaCO₃ nanoparticles of 30–70 nm. The targeted SiO₂/CaCO₃ nanocomposites were prepared with different molar ratio of SiO₂:CaCO₃ 1:15, 1:10 and 1:5. The percentage of silica increased from 62.5% to 82.9% by thermal treatment of SBRSA at 800 °C for 2 h. The prepared SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites were characterized by using XRD, XRF, TEM, FT-IR and Zeta potential. The results indicate that a pure semi-crystalline SiO₂ nanoparticle and semi-crystalline shell of SiO₂ coated CaCO₃ core particles were produced. The work extended also to investigate the effect of the prepared fillers on physical, mechanical and optical properties of paper.Application of the prepared SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites improved the optical properties of paper (brightness, whiteness and opacity) but it slightly reduced the mechanical properties when compared to commercial precipitated CaCO₃ (PCC) filler.The results showed that the retention of SiO₂ nano-particles was highly increased. The retention of the prepared nanocomposites increased along with increasing of SiO₂:CaCO₃ molar ratio.     

Controlled synthesis of calcium carbonate in a mixed aqueous solution of PSMA and CTAB

A mixed system of poly (styrene-alt-maleic acid) (PSMA) and cetyltrimethylammonium bromide (CTAB) was used as a very effective crystal growth modifier to direct the controlled synthesis of CaCO₃ crystals with various morphologies and polymorphs. The as-prepared products were characterized with scanning electron microscopy and X-ray diffraction. It was found that the concentrations and relative ratios of PSMA and CTAB in the mixed aqueous solution were turned out to be important parameters for the morphology and polymorph of CaCO₃ crystals. Various morphologies of CaCO₃ crystals, such as hollow microsphere, peanut and so on, were produced depending on the concentrations and relative ratios of PSMA and CTAB. Moreover, the formation mechanisms of CaCO₃ crystals with different morphologies were discussed.     

Influence of N,O-carboxymethyl chitosan on the properties of octadecanoic acid/octadecylamine monolayers and the fractal structure of calcium carbonate

The properties of octadecanoic acid-otctadecylamine monolayers and growth of calcium carbonate (CaCO₃) induced by the monolayers on the surface of supersaturated CaCO₃ solution with N,O-carboxymethyl chitosan (CMC) are studied. The results suggest that CMC is either adsorbed on or inserted into the monolayers, as is confirmed by π-A, dπ/dA-A, and π-t isotherms. The adsorption of CMC changes the properties of the monolayers, a process that results in the transformation of the shape of CaCO₃ particles from crystal-like into the fractal pattern beneath the monolayers. Different fractal morphologies, such as butterfly and wicker branches consisting of hollow ellipsoidal, solid ellipsoidal, and spherical particles, correspondingly, are observed; these morphologies depend on the CMC concentration in the subphase. The dimensions of fractal patterns are determined. The mechanisms of the formation of CaCO₃ crystals and fractal structures are discussed. The text was submitted by the authors in English.     

Effects of PAA additive and temperature on morphology of calcium carbonate particles

Calcium carbonate particles with various shapes were prepared by the reaction of sodium carbonate with calcium chloride in the absence and presence of a polyacrylic acid (PAA) at 25°C and 80°C, respectively. The as-prepared products were characterized with scanning electron microscopy and X-ray diffraction. The effects of pH, temperatures, aging time and concentration of PAA and CaCO₃ on the crystal form and morphologies of the as-prepared CaCO₃ were investigated. The results show that pH, temperatures, concentration of PAA and CaCO₃ are important parameters for the control of morphologies of CaCO₃. Various crystal morphologies of calcite, such as, plates, rhombohedras, rectangles, ellipsoids, cubes, etc. can be obtained depending on the experimental conditions. Especially, the monodispersed cubic calcite particles can be produced by PAA addition at 80°C. Moreover, higher temperature is beneficial to the formation of monodispersed cubic or rectangular calcite particles. This research may provide new insight into the control of morphologies of calcium carbonate and the biomimetic synthesis of novel inorganic materials.     

Preparation of hollow titania and strontium titanate spheres using sol–gel derived silica gel particles as templates

A facile approach, based on polyelectrolyte-mediated electrostatic adsorption of a water-soluble titanium complex on colloidal templates and hydrothermal treatment, is presented for the formation of hollow titania (TiO₂) and strontium titanate (SrTiO₃) spheres. Monodispersed silica gel particles were prepared by the sol?Cgel method and adopted as core templates. Deposition of a water-soluble titanium complex, titanium (IV) bis(ammoniumlactato)dihydroxide (TALH), on the silica gel particles was carried out via the layer-by-layer assembly technique. Hollow spheres were successfully formed from the core?Cshell particles. The silica gel particles used as core templates dissolved during hydrothermal treatment because of the particles?? undeveloped siloxane network. In addition, the hydrothermal treatment induced crystallization of the hollow shells. Therefore, the hydrothermal treatment played two roles; removal of the silica templates and crystallization of the hollow shells. When deionized water was used, hollow TiO₂ spheres were obtained. Hollow SrTiO₃ spheres could also be formed when an aqueous solution of Sr(OH)₂ was used. The approach presented here could be exploited as a novel and sustainable approach for the fabrication of a range of different inorganic hollow spheres.