Separation of uranium(VI) and transition metal ions with 4-(2-thiazolylazo)resorcinol by capillary electrophoresis

A capillary electrophoresis method utilizing 4-(2-thiazolylazo)resorcinol (TAR) was developed to separate uranium, cobalt, cadmium, nickel, titanium and copper metal ions. TAR was chosen as the visible absorbing chelating ligand because of its ability to form stable complexes with a wide variety of metals. Several parameters that included pH, electrophoretic run buffer concentration, buffer type and the influence of chelating ligand in the electrophoretic run buffer were examined to determine the best separating conditions. Optimum separation of the six metal chelates was achieved in a 15 mM Na2B4O7-NaH2PO4, pH 8.3 buffer containing 0.1 mM TAR. Method validation included injection and method precision studies as well as detection limit and linear dynamic range determination. High-ppb to low-ppm (w/w ratio) detection limits were achieved with linear dynamic ranges between 0.1 and 75 ppm.     

Determination of metal ions by capillary electrophoresis using pre-column complexation with 1,10-phenanthroline

The capillary electrophoretic separation of Fe(II), Cu(II) and Zn(II) ions in an acidic buffer solution (pH 2.5) by complexation with 1,10-phenanthroline is investigated. As 1,10-phenanthroline is a neutral ligand, the positively charged metal complexes formed migrate in the same direction as the EOF, providing a rapid separation of metal ions in acidic buffers. The method was applied to the determination of metal ions in vitamin tablets. Received: 5 January 1998 / Revised: 27 March 1998 / Accepted: 15 May 1998     

Determination of metal ions by capillary electrophoresis using pre-column complexation with 1,10-phenanthroline

The capillary electrophoretic separation of Fe(II), Cu(II) and Zn(II) ions in an acidic buffer solution (pH 2.5) by complexation with 1,10-phenanthroline is investigated. As 1,10-phenanthroline is a neutral ligand, the positively charged metal complexes formed migrate in the same direction as the EOF, providing a rapid separation of metal ions in acidic buffers. The method was applied to the determination of metal ions in vitamin tablets. Received: 5 January 1998 / Revised: 27 March 1998 / Accepted: 15 May 1998     

Solid-phase extraction and subsequent capillary zone electrophoresis of trace metal ions as soluble dithiocarbamate complexes

Summary Modest detectability in capillary electrophoresis is often a challenge for the determination of trace-level metal ions. This limitation has been addressed by the development of an enrichment procedure combining the formation of metal bis(carboxymethyl)dithiocarbamate complexes, water soluble at basic pH and sparingly soluble in an acidic environment, and solidphase extraction. Appropriate conditions were developed for a solid-phase extraction step well compatible with subsequent capillary electrophoretic separation in terms of the composition of electrophoresis and eluting buffers. At pH below 4 when the ligand carboxyl groups are non-ionized, metal ion complexes have no apparent charge and are efficiently retained on a conventional C₁₆ cartridge. Application of a basic eluent, a borate buffer at pH9, causes the complexes to be ionized and eluted rapidly and quantitatively. Parameters affecting the retention/recovery behavior, such as the pH and ligand concentration of the loading solution, flow-rate, eluting buffer pH and concentration, etc, were examined to attain the best possible enrichment factors for trace metal ions. As a result, an increase in sensitivity over two orders of magnitude was gained that permitted lowering the detection limits for copper(II), lead(II), cadmium(II), nickel(II), and mercury(II) down to a low-μg L⁻¹ level.     

Capillary Electrophoresis for the Simultaneous Determination of Metals by Using Ethylenediamine Tetraacetic Acid as Complexing Agent and Vancomycin as Complex Selector

A new separation system of capillary electrophoresis for the simultaneous determination of metals by using ethylenediamine tetraacetic acid （EDTA） as complexing agent and employing vancomycin as complex selector was described. The Z-shape cell capillary electrophoresis was used to enhance the sensitivity for the determination of the complexes of Cu（Ⅱ）, Ni（Ⅱ）, Co（Ⅱ） and Fe（Ⅲ） with EDTA. The partial filling method （co-current mode） was used in order to increase the selectivity of the electrophoretic method, meanwhile vancomycin was not present at the detector path during the detection of metal-EDTA complexes. The vancomycin concentration, phosphate concentration and pH of the buffer strongly influenced mobility, resolution and selectivity of the studied analytes. Under the optimal condition, the relative standard deviations （n=5） of the migration time and the peak area were less than 3.14% and 7.35%, respectively. Application of the Z-shape cell capillary electrophoresis method with UV detection and vancomycin loading led to the reliable determination of these metal ions in tap water and the recoveries were 97%-101%. The detection limits based on a signal to noise ratio of 3 ： 1 were found in the range of 2-10 μg·L^-1.     

Metal ion capillary zone electrophoresis with direct UV detection: Comparison of different migration modes for negatively charged chelates

Summary Several migration modes suitable for capillary zone electrophoretic (CZE) separation of metal ions in the form of 8-hydroxyquinoline-5-sulphonic acid complexes are described and compared. Superior analysis time, resolution, efficiency and detectability were achieved using reversed movement of anionic metal complexes (in the anode-to-cathode direction) under the action of the electroosmotic flow. This method allows the CZE analysis of multicomponent mixtures of transition metal ions as well as aluminium within about six minutes.     

Simultaneous detection of [metal(II)-tpen]2+ as kinetically inert cationic complexes using pre-capillary derivatization electrophoresis: an application to biological samples

A high resolution of doubly charged first row transition (Fe, Cu, Zn, Ni, Co, Mn) and heavy metal (Pb, Cd, Hg) ions was achieved in capillary electrophoresis (CE) with high sensitivity (sub-micromol dm(-3) level), using NN,N'N'-tetrakis(2-pyridylmethyl)ethylenediamine (TPEN) as a pre-capillary derivatizing agent. The non-charged reagent, TPEN, was applied to capillary zone electrophoresis (CZE) for the first time. Since complete spatial separation between the complexes and the ligand was carried out in a carrier buffer, which was free of TPEN, kinetic inertness of metal complexes was necessary for the detection in this pre-capillary method. All the nine listed metal complexes were detected: Ca(2+), Mg(2+), Al(3+), Fe(3+), and Co(3+) complexes were undetectable. This, interestingly, suggests that those nine cations form kinetically inert tpen complexes without strong charge-charge interactions between the metal ion and the ligand. It is expected that the hard-soft-acid-base (HSAB) principle governed the kinetics selectivity. With respect to the electrophoretic behavior, the addition of chloride ion and methanol to the carrier significantly improved the resolution. This is due to the formation of ternary complexes or ion aggregates and the solvation effect, respectively. These effects provided a satisfactory baseline resolution among the nine metal ions. An application to biological samples was demonstrated. Some metal ions in human serum and urine were successfully detected in a simple process without the need for deproteinization using a non-coated fused-silica capillary because of the differenciation in the direction of migration between organic matter and complexes.     

Determination of trace metals by capillary electrophoresis

A new analytical procedure is developed using a strong complexing agent, 1,10-phenanthroline (Phen), for direct UV detection of Zn, Mn, Cu, Co, Cd, and Fe at microg/L concentrations in environmental water samples. The metal chelates formed showed different electrophoretic mobilities and solved the comigration problem for capillary electrophoresis (CE) separation of free metal ions. To obtain stable metal-Phen chelates during the capillary zone electrophoresis (CZE) run, both pre-column and on-column complexation are required and threefold excess of Phen over metal ions should be added to the sample. The optimized background electrolyte (BGE) consists of 30 mM hydroxylamine hydrochloride and 0.1% methanol at pH 3.6. Under hydrodynamic sampling, CE run at + 20 kV in 65 cm x 0.05 mm ID fused-silica column with detection at 265 nm, baseline separation, satisfactory working ranges (10 microg/L to 5.5 mg/L), sensitive detection limits (1-3 microg/L), good repeatability for migration times (relative standard deviation, RSD 0.36-0.81%, n = 5), peak area (RSD 3.2-4.2%, n = 5) and peak height (RSD 3.2-4.5%, n = 5) were obtained for the metal cations investigated. The reliability of the method was established by parallel determination using the inductively coupled plasma-atomic emission spectrometry (ICP-AES) method giving results within statistical variation. The procedure developed is shown to provide a quick, sensitive, precise, and economic method for simultaneous determination of metal cations that can form stable chelates with Phen.     

Microchip separations of transition metal ions via LED absorbance detection of their PAR complexes

Micellar electrokinetic chromatography was utilized in the electrophoretic separation of seven transition metal ions, colorimetrically complexed by 4-(2-pyridylazo)resorcinol (PAR) on a glass capillary electrophoresis microchip. Detection of the PAR metal chelates was demonstrated using a green light emitting diode (540 nm) and a miniature photomultiplier tube. Parameters investigated included the effect of buffer type, pH and surfactant concentration (sodium dodecyl sulfate, SDS) on the separation efficiency. The optimally determined background electrolyte contained 10 mM ammonium phosphate buffer (pH 7.5), 1 mM PAR to prevent kinetic lability problems and 75 mM SDS for enhanced resolution. The separation of seven transition metal ions, Co2+, V3+, Ni2+, Cu2+, Fe2+, Mn2+ and Cd2+, was achievable in under 65 s, with the resolution of each metal ion in excess of 1.60. Detection limits obtained ranged from 400 ppb for Ni2+ to 1.2 ppm for Mn2+.     

Metal Ion Chromatography with Fluorescence Detection

Abstract

Nonpolar, agglomerated anion exchanger, and surface-sulfonated cation exchanger stationary phases have been used in conjunction with 8-hydroxyquinoline-5-sulfonic acid (HQS) in the eluent or as a postcolumn reagent for the separation and detection of a number of metals that form fluorescent HQS complexes. Several metals, notably those classified as transition metals, form nonfluorescent HQS chelates and quenches the fluorescence of other metal-HQS metal chelates. Such transition metals have been detected by introducing the fluorescent Al-HQS chelate postcolumn. Cation exchange stationary phases are the most useful for chromatographic applications involving HQS and are able to provide a variety of useful separations by tailoring elution conditions. Although not sensitive to Ba, the approach may be particularly good for the determination of the other alkaline earth metals. Fluorescence quenching resulting from Fe and Ni leaching from stainless steel chromatographic systems present a problem for trace analysis and accentuate the need for nonmetallic hardware. Subpicomole detection limits are attainable for Cd, Mg and Zn.     

Chromatographic determination of metal chelates of 2,6-diacetylpyridine bis(N-methylenepyridiniohydrazone)

Metal ions were determined chromatographically as their metal chelates after complexation with 2,6-diacetylpyridine bis(N-methylenepyridiniohydrazone). At a pH of 7 it was possible to separate and determine eight metal complexes, in a single run, under gradient conditions on a polyestyrene-divinylbenzene polymer-based column. Possible separation of rare earth complexes and ion-pairing behavior were also investigated. Linear calibration ranges and detection limits are presented for the metal complexes of Sn(II), Ti(IV), Mn(II), Co(II), Cd(II), Sb(III), Cu(II), Ni(II) and U(VI). Interferences due to the presence of other metal ions in solution were also investigated.     

Selective determination of cadmium(II) from divalent metal ions in environmental samples by capillary electrophoresis using in-capillary complexation with a lacunary Keggin-type [PW11O39]7- complex.

A novel capillary electrophoretic (CE) method, based on in-capillary complexation with [PW(11)O(39)](7-), was developed for the determination of cadmium(II) in natural water samples. When a sample solution is injected into a capillary containing 0.20 mM [PW(11)O(39)](7-) and 0.10 M malonate buffer (pH 3.0), the ternary Keggin-type complex, [P(Cd(II)W(11))O(39)](5-), which possesses high molar absorbtivities in the UV region, is formed in the capillary, and its migration toward the anode gives a well-defined migration peak in the electropherogram. An advantage of this method is that many divalent metal ions do not interfere. The proposed method was successfully applied to the determination of Cd(II) in environmental samples. The detection limits were 1 x 10(-7) and 5 x 10(-7) M for river-water and seawater samples, respectively (signal-to-noise ratio = 3).     

Capillary zone electrophoresis with UV-scanning detection for the analysis of metal species and their organic binding partners in biological systems

A capillary zone electrophoretic method with UV-scanning detection for the separation and identification of both free ligands and metal species is presented. The electrophoretic behavior of naturally occurring binding partners such as organic acids and amino acids was studied and compared with their metal-complexes. Copper(II) complexes of citrate and amino acids showed decreased electrophoretic mobilities and altered UV spectra. The optimized method was validated on ultrafiltered cow's milk and human milk samples. In cow's milk six low molecular weight substances, including citrate, orotate, and hippurate, could be separated. Metal supplementation with Cu(II), Ni(II), or Zn(II) decreased not only the citrate peak but also the orotate signal and in the case of copper(II) supplementation a new signal for the copper(II)-citrate complex appeared. In human milk samples various amino acids such as glutamate, phenylalanine, tyrosine, and tryptophan could be identified besides citrate. The electrophoretic mobilites and peak areas of the amino acids were also influenced by the metal supplementation.     

The use of metal ion-supplemented buffers to enhance the resolution of peptides in capillary zone electrophoresis

The potential of metal ion-containing buffers to enhance the resolution of peptides in capillary zone electrophoresis was evaluated. The impact of adding Cu(II) and Zn(II) salts to electrophoresis buffers is shown to affect the migrational behavior of several dipeptides containing histidine. Interaction with a metal ion differentially decreases the electrophoretic mobilities of peptides which comigrate in the absence of metal ions, thus causing their separation. This effect is obtained at low pH where the large net charge on the samples yields short analysis times. The dependence of the resolution on Zn(II) concentration is presented for two different samples. The influence of the background buffer is discussed.     

Capillary electrophoresis as a nanoreactor of separation capability: on-capillary reaction catalyzed by transition metal ions

The catalytic oxidation of 1,2-dihydroxy-benzene-3,6-disulfonate (tiron) by metal ions has been studied for detection of the metal ions in capillary electrophoresis (CE). Although Co(2+) shows the strongest catalytic capability, some other metal ions also catalyze this reaction. If metal ions encounter a H(2)O(2 )zone after electrophoretic separation in the running buffer containing tiron, tiron is catalytically oxidized while the metal ion passes through the H(2)O(2) zone. Anionic tiron radicals produced by the reaction are finally measured by the detector; in this scheme, the capillary acts as a nano- or microreactor as well as a microseparator. The effective capillary length can be controlled by changing the interval between metal ion and H(2)O(2) injections. This scheme has been successfully applied to the detection of Co(2+), Cu(2+), Mn(2+), and VO(2+). The detectability is discussed from several viewpoints, such as the intrinsic catalyst ability of metal ions, the kinetics of the catalytic reaction, and reaction times determined by the mobility of the zone of the metal ion. Some strange behaviors, which cannot be predicted by batch experiments, are also reported.     

Reversed-phase HPLC determination of Co(II), Ni(II) and Fe(III) as their 2-(2-thiazolylazo)-5-dimethylaminophenol chelates

The optimum chromatographic separation conditions for Co(II), Ni(II), and Fe(III) chelates with 2-(2-thiazolylazo)-5-dimethylaminophenol (TAM) were investigated. The compositions of chelates were also determined by the HPLC method and thus the possible structure of chelates was given. A precolumn derivatization method was used, followed by separation on an octyl-bonded silica stationary phase with a methanol-tetrahydrofuran-water (40:9:51, v/v/v) mobile phase containing pH 5.8 acetate buffer and 1 x 10(-4)M TAM. The detection limits of Co(II), Ni(II), and Fe(III) at 560 nm are 0.03, 0.02 and 0.1 ng (S N = 2 ), respectively. They can be determined by means of the proposed method without interference from other common metal ions and have been determined in five standard alloys with satisfactory results.     

Highly sensitive chemiluminescence detection of copper(II) in capillary electrophoresis with field-amplified sample injection

Field-amplified sample injection of copper(II) was investigated using capillary electrophoresis with chemiluminescence detection. The sensitivity of copper(II) has been improved markedly by the field-amplified sample injection technique and the detection limit reaches 2 x 10(-11) M. By injection of a short plug of water before sample introduction, the sensitivity can be further improved 5-fold and the detection limit reaches 4 x 10(-12) M. The relative standard deviations (n = 6) of the migration time and the peak height are 0.61% and 4.7% at 1.0 x 10(-9) M Cu(II), respectively. Parameters affecting the field-amplified sample injection, such as separation voltage and concentration of electrophoretic buffer, have been investigated.     

Original paper application of cyclodextrins as modifiers in electrophoretic separation of metalloporphyrins

Several metallocomplexes of tetrakis-carboxyphenylporphyrin (TCPP) were separated on fused-silica capillary using CZE with UV-VIS detection. Metalloporphyrins of Co(II), Cu(II), Mn(II), Ni(II), and Zn(II) were formed directly in TCPP solution with addition of Cd(II) to increase the formation reaction rate. The composition of BGE, its concentration, and pH were optimized to ensure the stability of complexes and proper resolution. In particular, the problem of signals' shape was investigated and discussed. The presence of beta-CD in borate buffer significantly improved separation efficiency and signal shapes due to formation of inclusion complexes. Under the best separation conditions (50 mM borate running buffer at pH 9 with addition of 2 mM beta-CD, 30 kV applied voltage) a separation of metal complexes with TCPP was accomplished in 16 min.     

Gas and liquid chromatography of metal chelates of pentamethylene dithiocarbamate

Capillary GC and HPLC of metal chelates of pentamethylene dithiocarbamate were examined. Copper(II), nickel(II), cobalt(III), iron(III), manganese(II) and chromium(III) chelates formed in slightly acidic media (pH 5) were extracted in methyl isobutyl ketone or chloroform. Capillary GC elution and separation was carried out on methylsilicone DB-1 column (25 m x 0.2 mm I.D.) with film thickness 0.25 microm. Electron-capture detection was used. Elution was carried at initial column temperature 200 degrees C with an increment at a rate of 5 degrees C/min up to 250 degrees C and maximum temperature was maintained for 10 min. Symmetrical peaks with baseline separation were obtained with the metal chelates investigated with linear calibration range between 5 and 25 microg/ml for each metal ion and detection limits in the range of 0.5-6.0 microg/ml corresponding to 27-333 pg of metal ion reaching to the detector. HPLC separation was carried out from LiChrosorb ODS, 5 microm column and complexes eluted with methanol-water-1 mM sodium acetate (70:28:2, v/v) with a flow-rate of 1.2 ml/ml. UV detection was at 260 nm. The detection limits obtained were in the range 2-6 microg/ml. The methods were applied to the determination of metal ions in canal water and coal samples with RSD values within 4.15%. The results when compared with a standard flame atomic absorption spectrophotometric method and revealed no significant difference.     

Separation and sweeping of metal ions with EDTA in CZE-ESI-MS

Ethylenediaminetetraacetic acid (EDTA) in the background electrolyte (BGE) of capillary zone electrophoresis coupled to an electrospray ionization mass spectrometer is presented as an approach for the determination of metal ions. Significant signals for the metal-ligand complexes were observed even when EDTA was continually eluted from the capillary during the entire electrophoretic run. The signal-to-noise ratio was improved by the addition of ammonia to the sheath liquid and by using an acquisition m/z range above the m/z of EDTA. The LODs for the test metal ions (i.e. calcium(II), manganese(II), and zinc(II)) with conventional injection were around 1-2 mg/L with corrected peak areas that are linear from 8 to 100 mg/L. The presence of EDTA in the BGE was critical not only for the separation but also for sweeping via complexation as an on-line sample concentration technique. The peak height of the test metal ions was improved at least tenfold with sweeping via EDTA complexation and yielded LODs in the μg/L range.