亚运会大学生体育馆空间吸声体的设计和应用

大学生体育馆于1988年10月竣工,是亚运会工程中首先交付使用的体育场馆之一,全国农运会的球类、体操等比赛项目和闭幕式在该馆进行,通过使用,普遍反映语言清晰度高、声场均匀、噪声水平低和没有音质缺陷。 该馆采用屋架暴露(球节点网架)不设吊顶的建筑形式,使馆内有效容积巨增,每座占容积13.9m~3,是目前国内同类体育馆的2倍。在如此巨大的容积内,用有限的投资和声学处理面积达到预期的声学效果,是通过空间吸声体的合理设计和应用实现的。本文仅就空间吸声体的设计和应用作概要的介绍。     

薄板悬挂吸声体吸声性能的研究

本文提供并研究了薄板悬挂吸声体的吸声性能,研究结果表明：薄板悬挂吸声体低频段吸声性能较好,而中高频相对差点。     

耦合声阻抗在扩散吸声体设计中的应用研究

为解决小房间的音质设计问题,需要设计不同的扩散吸声体。利用共振吸声的边缘效应,通过不同共振频率的共振器耦合共振时的非线性声阻抗变化组合,形成既能高效吸声,又能均匀散射的声学界面。数值分析及实验结果表明,新型的扩散吸声体内部没有任何传统吸声材料的情况下,单位面积吸声量在中低频段可达1.3 m2,在高频段由于非线性声阻抗与共振器的辐射阻抗不匹配影响,相应吸声量降低到0.7 m2左右。耦合声阻抗的运用使得新型扩散吸声体吸声的效率高,频带宽,免去传统吸声材料的使用,在小房间的声学应用中具有突出的优势。     

对称折叠通道结构的低频通风吸声体*

为了消除或减少低频噪声,该文 提出了一种低频通风超材料吸声体,该吸声体由对称的折叠通道结构组成,具有深度亚波长、高通风空间占比和低频高效吸声的特性.通过传递矩阵方法、有限元模拟和四麦克风实验法,揭示了对称折叠通道结构通风吸声的物理机制.首先在理论上分析单个吸声体的通风吸声性能并进行了仿真模拟,在共振频率423 Hz附近,吸声系数大于0.9,通风空间占比高达40%.吸声单体的共振频率可通过改变折叠通道的长度来灵活调控,组合多个不同共振频率的吸声单体可以拓宽吸声体的有效吸声带宽.由四个吸声单体组合的通风吸声体可实现314－366 Hz频率范围内的高效声吸收(吸声系数大于0.8),且通风空间占比达到35%,而结构厚度仅为314 Hz时波长的1/10.该低频通风吸声体具有结构简单、结构强度高和容易制造等特点,在低频通风降噪领域有着潜在的应用前景．     

关于微穿孔板吸声体频带宽度极限的讨论

依据马大猷教授的微穿孔板吸声体准确理论,利用计算机辅助设计对于该结构频带宽度极限情况从理论上进行了讨论,把极限频宽和最大吸声系数的制约关系量化,并得到此情况下应用于低频或高频环境孔径的选用范围,以及此情况下板厚和穿孔率与传统观念不同的特点。以上分析结果以及所提供的结构参数为宽频带微穿孔板的具体设计提供有价值的参考。     

扩散吸声体的优化设计

由于扩散吸声体(Diffsorber)同时兼顾了扩散和吸声两方面的性能,在小房间的声学环境控制中有着特殊的功能。在比较成熟声吸收和声扩散理论的基础上,结合数论中的伪随机理论,提出利用吸声材料本身的声阻抗实现伪随机分布的新优化设计手段,并利用计算机编程实现,由此设计了多种不同吸声效果的扩散吸声体,以满足不同场合的需要。实验结果表明新方法的有效性。同时探讨了新型吸声扩散体的应用潜力。     

基于二次剩余序列的扩散吸声体的研究

本文对基于二次剩余序列的声学结构的吸声性能进行实验研究，并定性分析了它的吸声机理．研究表明，除了结构振动所产生的损耗之外，更重要的吸收源是结构表面由于声干涉所形成的附加声阻抗的影响．     

伪随机扩散体的吸声性能及其应用

本文介绍伪随机扩散体吸声性能的应用，提出减少扩散体结构厚度的实用设计，并应用于剧场观众厅以减少混响时间．     

上海市黄浦体育馆的声学设计

上海市黄浦体育馆建于1981年9月,是一座多用途大厅,除供体育比赛外,还兼作集会及音乐演出之用.容座总共3800个.大厅平顶采用十字形空间吸声体处理,式样美观新颖,效果良好而经济.中频(500—1000Hz)满场混响时间约1.3s.扩声系统采用分区式声柱布置方案.使用效果表明音质符合设计要求.     

分层吸声结构的声学设计与性能分析

本文给出了声波在多层介质中的传播方程，通过数值计算，分析了各层参数对分层吸声结构声学性能的影响规律。用参数匹配方法，对多层吸声结构各层材料的参数进行设计。结果表明，通过合理分布各层材料，多层吸声结构可以在较宽频段上达到满意的吸声性能。     

Enhanced and broadband absorber with surface pattern design for X-Band

A broadband and thin-layer microwave absorber is designed based on surface pattern design made by carbonyl iron and rubber composite. The bandwidth with reflection less than −10 dB covers the full X-band owing to two absorption peaks appeared simultaneously in both the simulation results and experimental results. In this work, the power loss and power flow diagram were present by CST simulation, which clearly explain the broadband absorption caused by double λ/4 matching absorption and interfacial scattering synergistic effect. A facile splicing method was provided to extend the absorption bandwidth for the magnetic absorbing materials.     

含螺旋单元频率选择表面的宽频带强吸收复合吸波体

设计和制备了含螺旋单元频率选择表面吸波片的三层复合吸波体,上层和下层均为磁性吸波片,中间层为带缺口的螺旋单元频率选择表面.复合吸波体在总厚度分别为1.4,1.7和2.0 mm时,其反射率在-10d B以下的频带宽度分别达到了9.29,6.69和7.11 GHz,与不含有频率选择表面的吸波体相比较(其他参数相同),-10d B以下反射率带宽分别提高了159.5%,69.3%和129.4%,复合吸波体在总厚度低于吸波体时,也取得了更好的反射效果.带缺口圆螺旋单元的频率选择表面嵌入吸波体中,引入了额外的吸收频带,拓宽了吸波体的反射率频带宽度.仿真分析表明嵌入频率选择表面能够改善吸波体的阻抗匹配性,进而影响其反射率.     

The Wheeler-Feynman absorber theory: A reinterpretation?

The “reinterpretation” of the Wheeler-Feynman absorber theory of radiation, as presented by H. Price in Refs. 1 and 2, is shown not to be a reinterpretation of the mathematical framework of the theory, but an alteration of the theory, which renders it asymmetric. It is shown that Price is mistaken in accusing Wheeler and Feynman of presenting flawed arguments as to whether the advanced and retarded components are distinct; and about the reasons for excluding the time-reversed version of the absorber theory.     

A metamaterial absorber with direction-selective and polarisation-insensitive properties

This paper reports the design of a metamaterial absorber with direction-selective and polarisation-insensitive property.Both theoretical and simulated results reveal that the absorber has a distinct absorption point with direction selectivity at 7.48 GHz,which is related to the resonance of the metamaterial and is not influenced by the polarisation.The retrieved impedance indicates that the impedance of the absorber can be tuned to approximatively match the impedance of the free space on one side and not to match the impedance of the free space on the other side.This design can result in the minimal reflectance,the minimal transmission and the highest absorbance at the absorption frequency.The distribution of the power loss indicates that the absorber is an excellent electromagnetic wave collector:the wave is first trapped and reinforced in certain specific locations,and then mostly consumed.The distribution of the surface current is consistent with the design,the retrieved impedance and the distribution of the power loss.This absorber may have applications in many scientific and technological areas.     

The acoustic performance of ventilated window with quarter-wave resonators and membrane absorber

Noise and air pollution problems become significantly in a busy city such as Hong Kong since buildings usually located close to the heavy traffic lines. Traditional openable window cannot fulfill all the functions of noise reduction, lighting and natural ventilation. A new ventilated window combines the multiple quarter-wave resonators (silencer) and the new wing wall designs aim to make a balance between acoustic and ventilation performances at the same time. Furthermore, the use of multiple-wave resonators and membrane absorber which made plexi-glass plastic sheet replace absorption material can improve the durability; avoid small particle emission and light transparency.The acoustic and ventilation performance of new ventilated window were examined in this study. Noise attenuation of the new ventilated window design has improved significantly by combine flexible absorber and quarter-wave resonator effects. Transmission loss of 10–22 dB can be achieved in the frequency range of 500 Hz–4 kHz band. Outlet air flow velocity of ventilated window design is higher than that of “an open window”. Thus, both the acoustics and ventilation performance of the new ventilated window is essential. Wind-driven natural ventilation is an effective strategy in maintaining the comfort and health of the indoor environment.     

一种极化不敏感和双面吸波的手性超材料吸波体

基于手性结构设计了一种极化不敏感和双面吸波的超材料吸波体.该吸波体的结构单元由手性结构和介质基板组成.仿真的电磁波正、反向入射时超材料吸波体的吸收率表明:该吸波结构的正、反面是互易的,具有双面吸波特性.仿真的不同极化角下超材料吸波体的吸收率表明:该超材料吸波体具有极化不敏感特性.仿真的不同入射角下超材料吸波体的吸收率表明:该超材料吸波体的入射角较窄.仿真的吸波体单元的表面电流和磁能密度分布表明:电、磁场之间存在交叉耦合,吸波与手性有关.仿真的不同损耗情况下超材料吸波体的吸收率表明:基板的介质损耗在吸波过程中起主导作用,金属的电阻热可以忽略不计.该超材料吸波体可能在要求双面吸波的领域中具有潜在的应用. 关键词： 极化不敏感 双面吸波 手性结构 超材料吸波体     

极薄宽角度平面超材料吸波体仿真与实验验证

仿真和实验验证了厚度极薄的平面结构超材料吸波体, 该吸波体采用加载交指电容的耶路撒冷十字结构, 通过增加单元间的耦合电容显著降低了其工作频率. 测试结果表明, 该超材料吸波体在1.58 GHz, 吸收率峰值为88.48%, 其厚度为2 mm, 约为1/95工作波长, 吸波体的单元尺寸为11 mm, 约为1/17工作波长. 此外, 通过金属通孔将耶路撒冷十字结构与金属底板相连接, 使其对斜入射横电和横磁极化电磁波具有宽角度吸收特性, 在60°时依然具有较高的吸收率, 且吸收峰频率几乎不发生偏移, 从而使其更具实用价值. 关键词： 极薄 宽角度 超材料吸波体     

The origin of reflection loss peaks in the double-layer electromagnetic wave absorber

We investigated the origin of reflection loss (RL) peaks of Co₂Z particle composite (t mm)/fake-shaped carbonyl iron (CI) particle composite (1.5 mm) double-layer absorbers backed by a perfect conductor in 0.1–18 GHz. The RL peak frequency in the low frequency region remains unvariable and the RL peak in the high frequency region moves to lower frequency with the increase of Co₂Z particle composite thickness. The investigation results indicated that the two RL peaks come from the quarter-wavelength cancellation at the interface from Co₂Z particle composite to CI particle composite and the interface from air to Co₂Z particle composite, respectively.     

极化无关双向吸收超材料吸波体的仿真与实验验证

设计并制作出极化无关双向吸收超材料吸波体.仿真结果表明,该吸波体对斜入射横电极化和横磁极化电磁波具有较好的吸收效果,其强损耗主要来自介质基板的介电损耗.实验测试结果表明,该吸波体在11.1 GHz对垂直入射电磁波实现双向强吸收,吸收率分别为95.9％和90.8％.该吸波体厚度较薄,工作波长约为1/34.该超材料吸波体具有吸收率高、厚度薄、设计简单、易于加工等优点.     

吸收波长和吸收效率可控的超材料吸收器

为了使超材料完美吸收器(metamaterial perfect absorber,MPA)能够同时实现吸收效率和吸收波长的控制,本文提出利用二氧化钒(VO2)和石墨烯作为MPA的材料,通过对MPA的结构设计,在红外波段实现了高吸收,吸收效率最高可达99％.研究发现通过改变VO2的温度和石墨烯的化学势,可同时实现MPA...