Amphiphilic di‐ and tri‐block copolymers based on poly(ethylene oxide) as a hydrophilic segment and poly(ε‐caprolactone) as a hydrophobic part are synthesized by the ring‐opening polymerization of ε‐caprolactone while using poly(ethylene glycol)s and methoxy poly(ethylene glycol)s of varying molar masses as macro‐initiators. The synthesized block copolymers are characterized with respect to their total relative molar mass and its distribution by size exclusion chromatography. Liquid chromatography at critical conditions of both blocks is established for the analysis of individual block lengths and tracking presence of unwanted homopolymers of both types in the block copolymer samples. New critical conditions of polycaprolactone on reversed phase column are reported using organic mobile phase. The established critical conditions of polycaprolactone extended the applicable molar mass range significantly compared to already reported critical conditions of polycaprolactone in aqueous mobile phase. Block copolymers are also analyzed at critical conditions of poly(ethylene glycol). Complete analysis of the di‐ and tri‐block copolymers at corresponding critical conditions provided a fair estimate of molar mass of non‐critical block besides information regarding presence of homopolymers of both types in the samples. 相似文献
The thermal properties of two series of AB di-block copolymers of poly(ϵ-caprolactone) (A) and poly(lactide) (B) and their blends were studied. Each series contained poly(lactide) blocks of opposite chirality. The length of the poly(ϵ-caprolactone) blocks was not varied (DP = 70), whereas the poly(lactide) blocks were of varying length (DP = 5 − 80). Blends of polymers containing blocks of opposite chirality were prepared by mixing in solution. The melting temperature of the PLA phase was raised by approximately 55 °C in the blends due to stereocomplex formation. The melting temperatures of the crystalline PCL and PLA phases strongly depended on the composition of the block copolymers. 相似文献
The realization of hierarchical shish‐kebab structures for stereocomplex poly(lactic acid) (PLA) is achieved by the application of a shear flow (100 s–1 for 1 s) mimicking what can be expected during polymer processing. Compared to the normal shearing scenarios, this transient and strong shear flow enables the creation of dense shish precursors in time‐ and energy‐saving manner. The distribution of crystal form associated with the hierarchical structure is revealed by 2D Fourier transform infrared spectroscopy imaging, creating a unique visualization for both spatial resolution and polymorphism identification. Interestingly, in the shear stereocomplex chains are preferentially extended and crystallized as stable central cores with weak temperature dependence, whereas the development of lateral kebabs is defined by the distinct relation to the crystallization temperature. Below the melting point of homocrystals, both homo and stereocomplex crystallization are engaged in lamellar packing. Above that, exclusive stereocomplex crystals are organized into ordered lamellae. Combining the direct observations at multiscale, the ordered alignment of stereocomplex chains is recognized as the molecular origin of fibrillar extended chain bundles that constitute the central row‐nuclei. The proposed hypothesis affords elucidation of shish‐kebab formation and unique polymorphism in sheared stereocomplex PLA, which generates opportunities for engendering hierarchically structured PLA with improved performance.
Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities. 相似文献
This paper aims to report the fabrication of biodegradable thin films with micro‐domains of cylindrical nanochannels through the solvent‐induced microphase separation of poly(L ‐lactide)‐block‐poly(ethylene glycol)‐block‐poly(L ‐lactide) (PLA‐b‐PEG‐b‐PLA) triblock copolymers with different block ratios. In our experimental scope, an increase in each of the block lengths of the PLA and PEG blocks led to both a variation in the average number density (146 to 32 per 100 µm2) and the size of the micro‐domains (140 to 427 nm). Analyses by atomic force microscopy (AFM) and fluorescence microscopy indicated that the hydrophilic PEG nanochannels were dispersed in the PLA matrix of the PLA‐b‐PEG‐b‐PLA films. We demonstrated that the micro‐domain morphology could be controlled not only by the block length of PEG, but also by the solvent evaporation conditions.
Block copolymers create various types of nano‐structures, e. g., spheres, rods, cubes, and lamellae. This review discloses the dynamic macromolecular organization of block copolymers comprising poly(L ‐lactide) (PLLA) and poly(oxyethylene) (PEG) that allows to simulate elaborate biological systems. The block copolymers, AB‐ (PLLA‐PEG) and ABA‐type (PLLA‐PEG‐PLLA), are synthesized by ordinary lactide polymerization to have a controlled block length. They are dispersed into an aqueous medium to prepare nano‐scale particles, consisting of hydrophobic PLLA and hydrophilic PEG in the core and shell, respectively. Then, the particles are placed on a flat substrate by the casting method. The particles are detected as discoids by AFM, having shrunk with loss of water. Heat‐treatment of these particles at 60°C (above Tg of PLLA) gives rise to a collapse into small fragments, which then aggregate into bands with nano‐size width and thickness. The PLLA‐PEG bands align parallel to each other, while the PLLA‐PEG‐PLLA bands form a characteristic network resembling the neuron system created in animal tissue. As analyzed by TEM diffraction, each is composed of α‐crystal of PLLA whose c‐axis (molecular axis) is perpendicular to the substrate surface. Based on this fact, a doubly twisted chain structure of PLLA is proposed in addition to a plausible mechanism for the self‐organization of the block copolymers. Derivatives of the PLLA‐PEG block copolymers can form far more interesting nano‐architectures. An equimolar mixture of enantiomeric copolymers, PLLA‐PEG‐PLLA and PDLA‐PEG‐PDLA, forms a hydrogel that is thermo‐responsive. The terminal‐modified poly(L ‐lactide)‐block‐polyoxyethylene monocinnamate (PLLA‐PEG‐C) forms a highly stabilized nanofiber by the photo‐reaction of the cinnamates placed in the outer layer of the nanobands. 相似文献
The blends of poly(1,3‐trimethylene carbonate‐b‐(l ‐lactide‐ran‐glycolide)) (PTLG) with poly(d ‐lactide) (PDLA) were prepared via solution‐casting method using CH2Cl2 as solvent. The poly(l ‐lactide) (PLLA) segments of PTLG with PDLA chain constructed as stereocomplex structures and growth stereocomplex crystals of PLA (sc‐PLA). The effects of sc‐PLA crystals on thermal behavior, mechanical properties, thermal decomposition of the PTLG/PDLA blends were investigated, respectively. The differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results showed that the total crystallinity of the PTLG/PDLA blends was increased with the PDLA content increasing. Heterogeneous nucleation of sc‐PLA crystals induced crystallization of the PLLA segments in PTLG. The crystallization temperature of samples shifted to 107.5°C for the PTLG/PDLA‐20 blends compared with that of the PTLG matrix, and decreased the half‐time of crystallization. The mechanical measurement results indicated that the tensile strength of the PTLG/PDLA blends was improved from 21.1 MPa of the PTLG matrix to 39.5 MPa of PTLG/PDLA‐20 blends. The results of kinetics of thermal decomposition of the PTLG/PDLA blends by TGA showed that the apparent activation energy of the PTLG/PDLA blends was increased from 59.1 to 72.1 kJ/mol with the increasing of the PDLA content from 3 wt% to 20 wt%, which indicated the enhancement of thermal stability of the PTLG/PDLA blends by addition of PDLA. Furthermore, the biocompatibility of the PTLG/PDLA blends cultured with human adipose‐derived stem cells was evaluated by CCK‐8 and live/dead staining. The experiment results proved the PTLG/PDLA blends were a kind of biomaterial with excellent physical performances with very low cytotoxicity. 相似文献