Thermal stability of organoclays with mono- and di-alkyl cationic surfactants

In this study, mono- and di-alkyl cationic surfactants were used to prepare organoclays through ion exchange and the prepared organoclays were characterised by X-ray diffraction (XRD) and thermogravimetric analysis (TG). Larger basal spacings were observed in the interlayer of the organoclays intercalated with DDDMA than organoclays intercalated with DDTMA. The DTG curves identify the thermal stability of organoclays intercalated with two different types of surfactants (DDTMA and DDDMA) and the different arrangements of the surfactant molecules intercalated in the montmorillonite. Both organoclays intercalated with organic surfactant molecules proved to be thermally stable at high temperature. This study provides an understanding of the structure and properties of organoclays, which will enhance the potential applications of organoclays in environmental remediation.     

Characterisation of organoclays and adsorption of p-nitrophenol: environmental application

Organoclays were synthesised through ion exchange of a single surfactant for sodium ions, and characterised by a range of method including X-ray diffraction (XRD), BET, X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), and transmission electron microscopy (TEM). The change in surface properties of montmorillonite and organoclays intercalated with the surfactant, tetradecyltrimethylammonium bromide (TDTMA) were determined using XRD through the change in basal spacing and the expansion occurred by the adsorbed p-nitrophenol. The changes of interlayer spacing were observed in TEM. In addition, the surface measurement such as specific surface area and pore volume was measured and calculated using BET method, this suggested the loaded surfactant is highly important to determine the sorption mechanism onto organoclays. The collected results of XPS provided the chemical composition of montmorillonite and organoclays, and the high-resolution XPS spectra offered the chemical states of prepared organoclays with binding energy. Using TGA and FT-IR, the confirmation of intercalated surfactant was investigated. The collected data from various techniques enable an understanding of the changes in structure and surface properties. This study is of importance to provide mechanisms for the adsorption of organic molecules, especially in contaminated environmental sites and polluted waters.     

Adsorption of p-nitrophenol on organoclays

In this study, organoclays were prepared through ion exchange of a single cationic surfactant, hexadecyltrimethylammonium bromide and characterised by a range of methods including X-ray diffraction (XRD) and thermogravimetric analysis. Changes in the surface properties of montmorillonite and the organoclays were observed and the basal spacings of organoclays with and without p-nitrophenol were determined using XRD. The thermal stability of both organoclays were measured using thermogravimetry. As the surfactant loading increased, the expanded basal spacings were observed, and different molecular configurations of surfactant were identified. When the surfactant loading exceeded 1.0 CEC, surfactant molecules tend to adsorb strongly on the clay surface and this resulted in increased affinity to organic compounds. The adsorbed p-nitrophenol and the surfactant decomposed simultaneously. Hence, the surfactant molecules and adsorbed p-nitrophenol are important in determining the thermal stabilities of organoclays. This study enhances the understanding of the structure and adsorption properties of organoclays and has further implications for the application of organoclays as filter materials for the removal of organic pollutants in aqueous solutions.     

Stabilization of hydroxyl-group-terminated SERS-marker molecules on microAg particles by silanization

Surfactant modified montmorillonitic clays synthesized by ion exchange using the hydrothermal reaction method have been compared using XRD and thermal analysis. X-ray diffraction (XRD) shows the changes in the surface properties of organoclays through expansion with surfactant loading. A polynomial relationship exists between the basal spacing and the CEC loading described by the equation y=0.3232x(2) + 0.2052x+1.2834 with R(2)=0.9955. Different arrangements of the surfactant molecules in the organoclays are inferred from the changes in basal spacings. para-Nitrophenol also causes the expansion of the montmorillonite clay and affects the arrangements of the surfactant molecules within the clay layers. Changes in the surfactant molecular arrangements were analyzed by thermogravimetry. Additional thermal decomposition steps were observed when para-nitrophenol is adsorbed on the organoclay.     

Preparation and Characteration of UV-cured EA/MMT Nanocomposites Via In-Situ Polymerization

A long-chain surfactant, enzoylbenzyl-N,N-dimethyl-N-octadecylammonium bromide (BDOB) with a benzophenone group, was synthesized to modify the montmorillonites (MMT) for the preparation of nanocomposites via photo-induced polymerization. The BDOB-modified MMT was characterized by the fourier transform infrared spectrometer (FTIR), thermal gravimetric analyzer (TGA) and X-ray diffraction (XRD), and the results of XRD indicated that the intercalated structures of BDOB-modified MMT was obtained. The conversion of the bisphenol A epoxy diacrylate (EA) was quantified by the FTIR, and the results indicated that conversion increased with an increase in the amount of BDOB-modified MMT. The morphologies of the UV-cured EA/MMT nanocomposites prepared from this organically modified MMT were studied by means of XRD and TEM, and the results showed that all the samples contained an intercalated structure with partial exfoliated structure. The results of TGA and mechanical properties also indicated that the thermal and mechanical properties of UV-cured nanocomposites were significantly enhanced due to the presence of the long chain surfactant organically modified MMT.     

Modification of Wyoming montmorillonite surfaces using a cationic surfactant

Surfaces of Wyoming SWy-2-Na-montmorillonite were modified using ultrasonic and hydrothermal methods through the intercalation and adsorption of the cationic surfactant octadecyltrimethylammonium bromide (ODTMA). Changes in the surfaces and structure were characterized using X-ray diffraction (XRD), thermal analysis (TG), and electron microscopy. The ultrasonic preparation method results in a higher surfactant concentration within the montmorillonite interlayer when compared with that from the hydrothermal method. Three different molecular environments for surfactants within the surface-modified montmorillonite are proposed upon the basis of their different decomposition temperatures. Both XRD patterns and TEM images demonstrate that SWy-2-Na-montmorillonite contains superlayers. TEM images of organoclays prepared at high surfactant concentrations show alternate basal spacings between neighboring layers. SEM images show that modification with surfactant reduces the clay particle size and aggregation. Organoclays prepared at low surfactant concentration display curved flakes, whereas they become flat with increasing intercalated surfactant. Novel surfactant-modified montmorillonite results in the formation of new nanophases with the potential for the removal of organic impurities from aqueous media.     

Influence of cationic surfactant removal on the thermal stability of organoclays

The microstructure, thermal stability, surface energy, and swelling characteristics of two kinds of commercial organoclays, before and after washing treatment with a mixture of H2O/ethanol, were investigated using X-ray diffraction (XRD), thermogravimetric analysis (TG/DTG), wettability measurement, and swelling measurement. This study demonstrates that the external-surface physically adsorbed surfactant can be removed after washing treatment, resulting in an increase in thermal stability and a decrease in surface energy of the resultant organoclays. Organoclays are difficult to be introduced into a solvent when their surface energies are lower than that of the solvent. On the other hand, the organoclay with gamma(organoclay) < gamma(solvent) is easier to be swollen and expandable by the solvent. The swelling and basal spacing measurements of the organoclays introduced into organic media indicate that the swelling factor and the interlayer swelling are two independent parameters. Both the polar character of the solvent and the swelling capacity of clay have a prominent effect on the interlayer swelling of the organoclays.     

Thermogravimetric study of <Emphasis Type="Italic">n</Emphasis>-alkylammonium-intercalated montmorillonites of different cation exchange capacity

Three n-alkylammonium salts of varying alkyl chain length were ion exchanged with montmorillonites (MMT) of different cation exchange capacity (CEC). The intercalated MMTs were characterized by thermogravimetry (TG), XRD, FTIR to acquire an insight into the intergallery structural arrangement of the organic alkylammonium cations (AAC). The increment in the intergallery spacing from XRD pattern was correlated with chain length and interlayer arrangement of AAC. Multiple organic mass-loss stages in thermogravimetric analysis indicate two types of anchorage of AAC in intercalated clay. CEC of MMT was found to influence the intergallery confinement and excess adsorption of AAC.     

Preparation and characterization of nano‐platelet‐like hydroxyapatite/gelatin nanocomposites

Nature has succeeded in creating numerous bionanocomposites such as bones and teeth consisting of nano‐platelets and biopolymers. Understanding of the mechanisms of formation and of the relation between structure and properties is vital for development of new materials for biomedical and engineering applications. In this work, varying contents of nano‐platelet‐like hydroxyapatite (HAp) has been used to reinforce gelatin (Gel) to produce nanocomposites. The prepared HAp/Gel nanocomposites were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric (TG/DTG) analyses. XRD, TEM, and FTIR results confirm the synthesis of intercalated and exfoliated nanostructures depending on the amount of gelatin. TG results reveal that the intercalated HAp/gelatin nanocomposites show improved thermal properties as compared to pristine gelatin. The results reported here can be expanded to other HAp–polymer systems, thus paving a new way of designing and fabricating biomemitic nanocomposites for future engineering and particularly for biomedical applications. Copyright © 2010 John Wiley & Sons, Ltd.     

Thermal stability of octadecyltrimethylammonium bromide modified montmorillonite organoclay

Organoclays are significant for providing a mechanism for the adsorption of organic molecules from potable water. As such their thermal stability is important. A combination of thermogravimetric analysis and infrared emission spectroscopy was used to determine this stability. Infrared emission spectroscopy (IES) was used to investigate the changes in the structure and surface characteristics of water and surfactant molecules in montmorillonite, octadecyltrimethylammonium bromide and organoclays prepared with the surfactant octadecyltrimethylammonium bromide with different surfactant loadings. These spectra collected at different temperatures give support to the results obtained from the thermal analysis and also provide additional evidence for the dehydration which is difficult to obtain by normal thermoanalytical techniques. The spectra provide information on the conformation of the surfactant molecules in the clay layers and the thermal decomposition of the organoclays. Infrared emission spectroscopy proved to be a useful tool for the study of the thermal stability of the organoclays.     

A novel organoclay with antibacterial activity prepared from montmorillonite and Chlorhexidini Acetas

A series of novel organoclays with antibacterial activity were synthesized using Ca-montmorillonite and Chlorhexidini Acetas (CA) by ion-exchange. The resultant organoclays were characterized using X-ray diffraction (XRD), high-resolution thermogravimetric analysis (HRTG) and Fourier transform infrared spectroscopy (FTIR). Their antibacterial activity was assayed by so-called halo method. In the organoclays prepared at low CA concentration, CA ions within the clay interlayer adopt a lateral monolayer while a 'kink' state or a special state with partial overlapping of the intercalated CA in the organoclays prepared at 1.0-4.0 CEC. HRTG analysis demonstrates that CA located outside the clay interlayer exists in all synthesized organoclays, resulting from the complex molecular configuration of CA. The dramatic decrease of the surface adsorbed water and interlayer water is caused by the surface property transformation and the replacement of hydrated cations by cationic surfactant. These observations are supported by the results of FTIR. Antibacterial activity test against E. coli demonstrates that the antibacterial activity of the resultant organoclays strongly depends on the content of CA. Meanwhile, the resultant organoclay shows a long-term antibacterial activity that can last for at least one year. These novel organoclays are of potential use in synthesis of organoclay-based materials with antibacterial activity.     

Preparation and thermal characterisation of poly(lactic acid) nanocomposites prepared from organoclays based on an amphoteric surfactant

New polymer-clay nanocomposites composed of poly(lactic acid) and a novel organoclay based on cocamidopropylbetaine (CAB) and sodium montmorillonite (MMT) were prepared by solution casting and characterised by X-Ray Diffraction Analysis (XRDA), Transmission Electron Microscopy (TEM) and Thermogravimetric Analysis (TGA). A similar series of composites based on PLA and Cloisite 30B, a commercially available organoclay, were prepared for comparison. The thermal stability of the CAB-MMT organoclays decreased with increasing surfactant loading. Experimental organoclays with an organic content similar to that of the commercial organoclay were found to be of comparable thermal stability. XRDA analysis of the PLA-organoclay nanocomposites showed that PLA intercalated the gallery space of both types of organoclay to similar extents and the increased spacing was confirmed by TEM. The thermal stabilities of the PLA-organoclay composites based on CAB-MMT were higher than those based on the commercial organoclay.     

Structure of organoclays--an X-ray diffraction and thermogravimetric analysis study

X-ray diffraction has been used to study the changes in the surface properties of a montmorillonitic clay through the changes in the basal spacings of montmorillonite (SWy-2) and surfactant-intercalated organoclays. Variation in the d-spacing was found to be a step function of the surfactant concentration. High-resolution thermogravimetric analysis (HRTG) shows that the thermal decomposition of SWy-2-MMTs modified with the surfactant octadecyltrimethylammonium bromide takes place in four steps. A mass-loss step is observed at room temperature and is attributed to dehydration of adsorption water. A second mass-loss step is observed over the temperature range 87.9 to 135.5 degrees C and is also attributed to dehydration of water hydrating metal cations such as Na+. The third mass loss occurs from 178.9 to 384.5 degrees C and is assigned to a loss of surfactant. The fourth mass-loss step is ascribed to the loss of OH units through dehydroxylation over the temperature range 556.0 to 636.4 degrees C. A model is proposed in which, up to 0.4 CEC, a surfactant monolayer is formed between the montmorillonitic clay layers; up to 0.8 CEC, a lateral-bilayer arrangement is formed; and above 1.5 CEC, a pseudotrimolecular layer is formed, with excess surfactant adsorbed on the clay surface.     

Functional copolymer/organo‐MMT nanoarchitectures. VII. Interlamellar controlled/living radical copolymerization of maleic anhydride with butyl methacrylate via preintercalated RAFT agent–organoclay complexes

We have developed a new approach for the synthesis of polymer nanocomposites using a bifunctional reversible addition–fragmentation chain transfer (RAFT) agent, two types of organo‐montmorillonites (O‐MMT), such as a non‐reactive dimethyldidodecyl ammonium (DMDA)‐MMT and a reactive octadecyl amine (ODA)‐MMT organoclays, maleic anhydride (MA), and n‐butyl methacrylate (BMA) monomers and a radical initiator. This method includes the following stages: (1) synthesis of RAFT intercalated O‐MMTs by a physical or chemical interaction of the RAFT agent having two pendant carboxylic groups [S,S′‐bis(α,α′‐dimethyl‐α″‐acetic acid) trithiocarbonate] with surface alkyl amines of O‐MMT containing tertiary ammonium cation or primary amine groups through strong H‐bonding and compexing/amidization reactions, respectively, and (2) utilization of these well dispersed and intercalated RAFT…O‐MMT complexes and amide derivative of RAFT…ODA‐MMT as new modified RAFT agents in radical‐initiated interlamellar controlled/living complex‐radical copolymerization of MA‐BMA monomer pair. Nanostructure and compositions of the synthesized RAFT…O‐MMT complexes and functional copolymer/O‐MMT hybrids were confirmed by FTIR, GPC, XRD, thermal (DSC‐TGA), SEM, and TEM morphology analyses. This simple and versatile method can be applied to a wide range of monomer/comonomer systems for the preparation of completely exfoliated macromolecular nanoarchitectures. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of surfactant agent upon the structure of montmorillonite

The modification of sodium montmorillonite (MMT) through the incorporation of amphiphilic octadecylammonium cations in various concentrations (10–200% CEC) into the clay’s interlayer spaces has been studied. High resolution thermogravimetric analysis shows that the thermal decomposition of modified montmorillonite occurs in three steps. The first step of mass loss is related to dehydration of adsorbed water and water hydrating metal cations such as Na⁺. The second step of mass loss is attributed to the decomposition of surfactant. The third step is due to the loss of OH units during the dehydroxylation of the montmorillonite. The conformation of the surfactant cations in the confined space of the silicate galleries is investigated by X-ray diffraction analysis. These analyses are very important for any attempt to incorporate the organomodified MMT particles into different media for various applications such as polymer nanocomposite preparation.     

Thermal stability and mechanical properties of sisal in cycle process

Differential thermal analysis (DTA) was the first thermal analysis technique used to qualitatively characterize natural clays and respective curves has been used since more than 60 years as their ‘fingerprint’. With the development of microprocessed equipments in the last decades, derivative thermogravimetric (DTG) curves also may be used for this purpose in some cases, which also may allow a quantitative characterization of clay components. TG and DTG curves are more indicated than DTA or DSC curves to identify and to better analyze the several decomposition steps of natural or synthetic organoclays. These questions are discussed in applications developed to characterize Brazilian kaolinitic clays, bentonites and organophilic clays.     

Investigation of structure and thermal stability of surfactant-modified Al-pillared montmorillonite

For combining the properties of organoclays and pillared clays, inorganic–organic clays have attracted much attention in recent years. In this study, Al Keggin cation pillared montmorillonites (Al-Mts) were first prepared and parts of Al-Mts were calcined at different temperatures (C-Al-Mts). The inorganic–organic montmorillonites were synthesized by intercalating Al-Mts and C-Al-Mts with the cationic surfactant, hexadecyltrimethyl ammonium bromide (HDTMAB). The products were characterized by X-ray diffraction, X-ray fluorescence, and simultaneous thermogravimetric analysis. For HDTMAB-modified uncalcined Al Keggin cation pillared montmorillonites (H-Al-Mts), the basal spacing increased with the increment of surfactant loading level, but the Al content of H-Al-Mts decreased simultaneously, indicating that the intercalated surfactant replaced some Al Keggin cations in the interlayer space. However, in the case of C-Al-Mts, the interlayer spaces could not be further expanded after surfactant modification, implying that the neighboring montmorillonite layers were “locked” by the aluminum pillars which were formed by dehydroxylation of Al Keggin cation pillars during thermal treatment. The thermal stability of HDTMAB-modified C-Al-Mts (H-C-Al-Mts) was much better than that of H-Al-Mts. The major mass loss of H-C-Al-Mts occurred at ca. 410 °C, corresponding to decomposition of intercalated surfactant cations. In contrast, H-Al-Mts displayed two mass loss temperatures at ca. 270 and 410 °C, corresponding to the evaporation of surfactant molecules and the decomposition of surfactant cations in the interlayer space, respectively.     

PREPARATION AND CHARACTERIZATION OF SOY PROTEIN ISOLATE(SPI)/MONTMORILLONITE(MMT) BIONANOCOMPOSITES

 The bionanocomposites of soy protein isolate (SPI)/montmorillonite (MMT) have been prepared successfully via simple melt mixing, in which MMT was used as nanofiller and glycerol was used as plasticizer. Their structures and properties were characterized with X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), thermogravimetric analysis and tensile testing. XRD、TEM and SEM results indicated that the MMT layers could be easily intercalated by the SPI matrix even by simple melt processing. The exfoliated MMT layers were randomly dispersed in the protein matrix as MMT content was low (less than 5 wt%), an incomplete exfoliation was evident from SEM results, and some primary particles were observed as the MMT content was high (from 5 wt% to 9 wt%). A significant improvement of the mechanical strength and thermal stability of SPI/MMT nanocomposites has been achieved. Our work suggests that simple melt processing is an efficient way to prepare SPI/MMT nanocomposites with exfoliated structure.     

A X-ray photoelectron spectroscopy study of HDTMAB distribution within organoclays

X-ray photoelectron spectroscopy (XPS) in combination with X-ray diffraction (XRD) and high-resolution thermogravimetric analysis (HRTG) has been used to investigate the surfactant distribution within the organoclays prepared at different surfactant concentrations. This study demonstrates that the surfactant distribution within the organoclays depends strongly on the surfactant loadings. In the organoclays prepared at relative low surfactant concentrations, the surfactant cations mainly locate in the clay interlayer, whereas the surfactants occupy both the clay interlayer space and the interparticle pores in the organoclays prepared at high surfactant concentrations. This is in accordance with the dramatic pore volume decrease of organoclays compared to those of starting clays. XPS survey scans show that, at low surfactant concentration (<1.0 CEC), the ion exchange between Na⁺ and HDTMA⁺ is dominant, whereas both cations and ion pairs occur in the organoclays prepared at high concentrations (>1.0 CEC). High-resolution XPS spectra show that the modification of clay with surfactants has prominent influences on the binding energies of the atoms in both clays and surfactants, and nitrogen is the most sensitive to the surfactant distribution within the organoclays.     

聚合物调控氧化钛层柱蒙脱石的结构和性能研究

为了改善氧化钛层柱蒙脱石的结构性能,以长链聚合物-端氨基聚甲基环氧乙烷(PPO-D-2000)为结构调节剂,调控合成了聚合物-氧化钛层柱蒙脱石材料。采用X射线粉末衍射、红外、拉曼光谱、TG/DSC、TEM和BET等手段进行了结构表征。结果表明,相比于小分子量表面活性剂而言,长链聚合物不仅能显著提高氧化钛层柱蒙脱石中的二氧化钛含量,而且比表面积比单独氧化钛柱撑蒙脱石增加了约13%,达到241.52m2/g,尤其是孔径、孔体积等孔道结构参数增加一倍左右。将合成的柱撑蒙脱石材料应用于对水中甲基橙的吸附和光催化性能研究表明,聚合物的调控作用能提高氧化钛层柱蒙脱石的吸附能力,光催化效率也有所改善。因此,聚合物对优化无机层柱粘土材料结构、改善吸附和催化性能具有良好的调控作用,为发展环境催化材料提供了新的途径。