Chiral capillary electrophoretic method for quantification of apomorphine

A new method for chiral determination of apomorphine enantiomers was developed and validated. Seven different neutral and charged cyclodextrins were tested for enantioselectivity on R,S-apomorphine. Sulfobutylether-beta-cyclodextrin was found to offer the best resolution, but with this system, four peaks were detected from a solution of the two enantiomers, which was suggested to be the result of different forms of the complex between the selector and apomorphine. A complexation constant was estimated for a complex of 1:1 ratio for the second and the fourth peak, whereas the other two peaks were fitted to a model ratio of 1:2 (analyte-selector). To avoid this phenomenon, hydroxypropyl-beta-cyclodextrin was then chosen as the chiral selector. An optimisation study was performed on three factors: concentration of the chiral selector, pH of the buffer, and applied voltage. Optimum conditions were: 14 mM of hydroxypropyl-beta-cyclodextrin, pH 3.0, and 16 kV. UV detection was at 200 nm. The method was validated at the chosen conditions, offering a limit of detection of 0.2 microM and a limit of quantification of 0.5 microM. The validated method was applied for the determination of R,S-apomorphine in a transport study with an in vitro cell culture model of the intestinal mucosa (Caco-2).     

Development of a capillary electrophoretic method for the analysis of amino acids containing tablets

Ketosteril is an enteral medicinal product indicated for prevention and therapy in chronic renal insufficiency in connection with a low protein diet. Tablets of Ketosteril contain five essential amino acids like: Lys, His, Thr, Trp, Tyr and another five amino acids in the form of their hydroxy and keto analogues as calcium salts, that are: alpha-ketoleucine, alpha-ketoisoleucine, alpha-ketovaline, alpha-ketophenylalanine and alpha-hydroxymethionine. The composition of Ketosteril tablets is routinely tested with three LC methods. Capillary electrophoretic method seems to be a good alternative for amino acids and their analogues determination in multicomponent pharmaceuticals because of short analysis time and the possibility to assay all components during a single run without any pretreatment. Electrophoresis was performed in 50 microm I.D. fused-silica capillaries with 65 cm distance to the detector. Capillaries were installed in Waters Quanta 4000 electrophoretic equipment with a positive power supply and on-line UV detection at 214 nm. Separations were done in a buffer containing 40 mM Tris and 160 mM boric acid titrated with NaOH to pH 10. The method developed allows the separation of all investigated analytes with an efficiency of n = 230,000 and 20 min analysis time. The method was applied for determination of all components of Ketosteril in commercial tablets.     

Development and validation of a capillary electrophoretic method for the determination of amiodarone and desethylamiodarone

Summary A simple, sensitive and rapid capillary electrophoretic method has been developed for the separation and quantification of amiodarone and its metabolite, desethylamiodarone. The compounds were separated in a capillary of 45 cm effective length and 75 μm i.d., by use of an applied voltage of 25 kV and an electrolyte containing 15mm ADA buffer (pH 7.5), 10mm SDS, and 70% (v/v) acetonitrile. The selectivity, precision, linearity, range, sensitivity, and robustness of the method were good. The applicability of the assay was demonstrated by analyzing these drugs in serum. Electrokinetic injection with field-amplified sample-stacking was used to increase sensitivity. The limit of detection of the serum assay was 6.46 ng mL⁻¹ and the precision 3.7%.     

Multiple response optimization applied to the development of a capillary electrophoretic method for pharmaceutical analysis

Multiple response simultaneous optimization by using the desirability function was used for the development of a capillary electrophoresis method for the simultaneous determination of four active ingredients in pharmaceutical preparations: vitamins B₆ and B₁₂, dexamethasone and lidocaine hydrochloride. Five responses were simultaneously optimized: the three resolutions, the analysis time and the capillary current. This latter response was taken into account in order to improve the quality of the separations. The separation was carried out by using capillary zone electrophoresis (CZE) with a silica capillary and UV detection (240 nm). The optimum conditions were: 57.0 mmol l⁻¹ sodium phosphate buffer solution, pH 7.0 and voltage = 17.2 kV. Good results concerning precision (CV lower than 2%), accuracy (recoveries ranged between 98.5 and 102.6%) and selectivity were obtained in the concentration range studied for the four compounds. These results are comparable to those provided by the reference high performance liquid chromatography (HPLC) technique.     

Optimization and validation of a capillary zone electrophoretic method for the analysis of several angiotensin-II-receptor antagonists

We optimized a capillary zone electrophoretic method for separation of six angiotensin-II-receptor antagonists (ARA-IIs): candesartan, eprosartan, irbesartan, losartan potassium, telmisartan, and valsartan. A three-level, full-factorial design was applied to study the effect of the pH and molarity of the running buffer on separation. Combination of the studied parameters permitted the separation of the six ARA-IIs, which was best carried out using 60 mM sodium phosphate buffer (pH 2.5). The same system can also be applied for the quantitative determination of these compounds, but only for the more soluble ones. Some parameters (linearity, precision and accuracy) were validated.     

Bacterial surface layer proteins as a novel capillary coating material for capillary electrophoretic separations

A novel concept for stable coating in capillary electrophoresis, based on recrystallization of surface layer proteins on hydrophobized fused silica capillaries, was demonstrated. Surface layer protein A (SlpA) from Lactobacillus acidophilus bacteria was extracted, purified and used for coating pre-silanized glass substrates presenting different surface wettabilities (either hydrophobic or hydrophilic). Contact angle determination on SlpA-coated hydrophobic silica slides showed that the surfaces turned to hydrophilic after coating (53 ± 5°), due to a protein monolayer formation by protein-surface hydrophobic interactions. Visualization by atomic force microscopy demonstrated the presence of a SlpA layer on methylated silica slides displaying a surface roughness of 0.44 ± 0.02 nm. Additionally, a protein layer was visualized by fluorescence microscopy in methylated silica capillaries coated with SlpA and fluorescein isothiocyanate-labeled. The SlpA-coating showed an outstanding stability, even after treatment with 20 mM NaOH (pH 12.3). The electroosmotic flow in coated capillaries showed a partial suppression at pH 7.50 (3.8 ± 0.5 10⁻⁹ m² V⁻¹ s⁻¹) when compared with unmodified fused silica (5.9 ± 0.1 10⁻⁸ m² V⁻¹ s⁻¹). To demonstrate the potential of this novel coating, the SlpA-coated capillaries were applied for the first time for electrophoretic separation, and proved to be very suitable for the isotachophoretic separation of lipoproteins in human serum. The separations showed a high degree of repeatability (absolute migration times with 1.1–1.8% coefficient-of-variation (CV) within a day) and 2–3% CV inter-capillary reproducibility. The capillaries were stable for more than 100 runs at pH 9.40, and showed to be an exceptional alternative for challenging electrophoretic separations at long-term use.     

A capillary zone electrophoretic method for the study of formation of a covalent conjugate between microcystin LR and protein phosphatase 2A

The study of conjugate formation between microcystin (MCYST)-LR and protein phosphatase (PP) 2A, which was isolated from bovine kidney and mouse brain, was achieved by using a highly efficient capillary zone electrophoretic (CZE) separation method. The MCYST-LR-PP2A conjugate (from bovine kidney) was resolved from its precursor after just 15 min of incubation. Moreover, the migration time, and, hence, the total analysis time, was less than 5 min. While the present findings of the time lag between conjugate formation and full inhibition are not novel, the CZE method does provide an alternative tool to HPLC with a higher separation efficiency to yield data for kinetic and mechanistic studies of the enzyme-toxin interaction. The CZE data reported here were found not to be adequately described by a first-order kinetic model. Moreover, the CZE method, which involves the use of a low ionic strength aqueous buffer, does not suffer from the drawback of the use of denaturing organic solvents such as those used in HPLC.     

Development of a capillary electrophoretic method for determination of plasma clearance of iohexol in dogs and cats

Renal function can be monitored by estimation of the glomerular filtration rate (GFR), for example, through measurement of the plasma clearance of a marker that is freely filtrated through the kidney without reabsorption. It has been proposed that iohexol is the most accurate marker for GFR determination in cats and dogs. However, there is a need for a validated capillary electrophoretic method that covers the concentration range for a full curve clearance estimate of iohexol. In the final method, the plasma samples were protein precipitated and the supernatant was analyzed in a background electrolyte containing borate buffer (0.06 m , pH 10.0). The method developed was proved to be linear (concentration range 18– 2900 mg/L) and had a good precision (e.g. 2.3–2.9% at 88 mg/L) and accuracy (e.g. 101–105% at 88 mg/L). Finally, the method was compared with a previously published and validated HPLC‐UV method by parallel analysis of clinical plasma samples from dogs and cats administered Omnipaque®. This comparison showed excellent agreement between the two methods and no proportional or systematic error was observed. The proposed method is simple and has a low cost per sample, which makes it applicable for routine analysis. Copyright © 2014 John Wiley & Sons, Ltd.     

Optimization and validation of a capillary zone electrophoretic method for the simultaneous analysis of four atypical antipsychotics

A capillary zone electrophoretic method has been developed and optimized for separation of four atypical antipsychotics (AAPs): clothiapine (cT), clozapine (cZ), olanzapine (O), and quetiapine (Q). A three-level full-factorial design was applied to study the effect of the pH and molarity of the running buffer on separation. Combination of the studied parameters permitted the separation of the four AAPs, which was best carried out using 80 mM sodium phosphate buffer (pH 3.5). The same system can also be applied for the quantitative determination of these compounds. The method was then validated regarding linearity, precision, and accuracy. Especially, the possibility of simultaneous quantification and identification of the active ingredient in the finished product is very attractive.     

Rapid capillary electrophoretic method for the determination of clozapine and desmethylclozapine in human plasma

A rapid and sensitive high-performance capillary electrophoretic method for the determination of clozapine and its main metabolite desmethylclozapine in human plasma was developed. The separation of the two analytes was carried out in an untreated fused-silica capillary [33 cm (8.5 cm effective length) x 50 microm I.D.] filled with a background electrolyte at pH 2.5 containing beta-cyclodextrin. Baseline separation of clozapine and desmethylclozapine was recorded in less than 3 min. An accurate sample pretreatment by means of solid-phase extraction and subsequent concentration allows for reliable quantitation of clozapine in the plasma of schizophrenic patients under treatment with the drug. The method showed good precision (mean RSD = 4.0%) as well as satisfactory extraction yields (approximately 88%) and a good sensitivity (limit of quantitation = 0.075 microg ml(-1), limit of detection = 0.025 microg ml(-1)).     

High-throughput capillary electrophoretic method for determination of total aminothiols in plasma and urine.

Increased interest in the analysis of aminothiols in body fluids during the last years results in a request for high-throughput analytical methods for their determination. We report here a novel, high-throughput method for the determination of total concentrations of biogenous aminothiols - homocysteine, cysteine, glutathione, cysteinylglycine, gamma-glutamylcysteine, and of penicilamine, mercaptopropionylglycine, and cysteamine, three compounds used to treat disorders of aminothiol metabolism in plasma and urine. Samples were reduced with tris(carboxyethyl)phosphine and labeled with 5-(bromomethyl)fluorescein. Capillary electrophoretic separations were performed in 60 mmol/L borate - 15 mmol/L sodium dodecyl sulfate - 2-amino-2-methyl-1-propanol, pH 10.0, with laser-induced fluorescence detection. Analysis time was less than 2 min. The assay is linear (r > 0.999) up to 500 micromol/L. Reproducibilities of migration times (coefficient of variation, CV) were < 0.5%. Interassay repeatabilities (CV, n = 10) were 5.08% and 6.09% for 5 micromol/L addition of homocysteine and 0.60% and 3.78% for 100 micromol/L addition of cysteine in plasma and urine, respectively. Recovery values were within 94-106% and sensitivity was better than 0.19 micromol/L for all analyzed compounds. Results agreed well with a standard high-performance liquid chromatography (HPLC) method. The diagnostic usefulness of the method has been proven on 79 samples of cystinuric patients and 12 samples of homocystinuric patients. We report here a novel method for the determination of aminothiols in body fluids by capillary electrophoresis (CE). Determination is fast and sensitive enough for diagnostic purposes.     

Development of a capillary electrophoretic method for the separation of diastereoisomers of a new human immunodeficiency virus protease inhibitor

A capillary electrophoretic (CE) method was developed for the separation of diastereoisomers of a new human immunodeficiency virus (HIV) protease inhibitor TMC114. In total 16 isomers of this drug have been synthesized (eight pairs of enantiomers). We succeeded in the separation of the eight diastereoisomers, but no enantiomers could be separated. Because of the high similarity and water-insolubility of these isomers, the separation is a real challenge. Different CE modes were tried out: capillary zone electrophoresis (CZE), nonaqueous capillary electrophoresis (NACE), micellar electrokinetic capillary chromatography (MEKC), and microemulsion electrokinetic capillary chromatography (MEEKC). Only MEEKC offered resolution of these compounds.     

Stable neutral double hydrophilic block copolymer capillary coating for capillary electrophoretic separations

Quaternized diblock copolymer, poly(N‐methyl‐2‐vinylpyridinium iodide‐block‐ethylene oxide), was successfully used as a neutral, dynamic coating to suppress the electroosmotic flow. The block copolymer consisted of two polymers that were linked covalently together. The cationic block (poly(N‐methyl‐2‐vinylpyridinium iodide)) was bound efficiently to the negatively charged capillary wall via electrostatic interactions, and the hydrophilic block (ethylene oxide) stabilized the system and created a neutral capillary surface with ultralow electroosmotic flow (+2.0 ± 4.5 × 10^?10 m²/Vs). The main advantages of the coating were simple and fast preparation, easy regeneration and automation, and stable electroosmotic flow. To emphasize the potential of this type of coating its stability was measured at a wide pH range demonstrating a high stability in the pH range of 4.0–10.5 and lifetime up to 8 days. The successful studies carried out with beta‐blockers, basic proteins, and lipoproteins proved the suitability of the coating for the separation of different sized analytes. Furthermore, the neutral coating developed is useful in a wide range of protein analysis and biological interaction studies under physiological condition.     

Applications of a sulfonated-polymer wall-modified open-tubular fused-silica capillary in capillary zone electrophoretic separations

A fused-silica capillary that is wall-modified via chemically bonding a sulfonated polymer to the capillary wall has a uniform negative charge density on its surface and produces an electroosmotic flow (EOF) greater than 4 x 10(-4) cm2 V(-1) s(-1) The EOF is nearly independent of buffer pH over the pH range of 2 to 10 and is lower than the EOF obtained for the bare fused-silica capillary at the more basic pH but is higher at the more acidic buffer pH. Optimization of buffer pH can be based on analyte pKa values to improve the overall quality of the capillary zone electrophoresis (CZE) separation of complex mixtures of weak acid and base analytes. Because of the high EOF in an acidic buffer, the capillary is useful for the separation of weak organic bases which are in their cation forms in the acidic buffer. EOF for the sulfonic acid bonded phase capillary can be adjusted via buffer additives such as organic solvent, tetraalkylammonium salts, multivalent cations and alkylsulfonic acids. The advantages of utilizing buffer pH and the EOF buffer modifiers to enhance migration time, selectivity, and resolution in CZE separations with this capillary are illustrated using a series of test analyte mixtures of inorganic anions, carboxylic acids, alkylsulfonic acids, benzenesulfonic acids, sulfas, pyridines, anilines or small-chain peptides.     

Ultramicro enzyme assays in a capillary electrophoretic system.

This paper describes an ultramicro method for achieving enzyme assays. Enzyme saturating concentrations of substrate, coenzyme when appropriate, and running buffer were mixed and used to fill a deactivated fused-silica capillary in a capillary zone electrophoresis apparatus. The enzyme glucose-6-phosphate dehydrogenase was injected by either electrophoresis or siphoning and mixed with the reagents in the capillary by electrophoretic mixing. Enzyme activity was assayed by electrophoresing the product, reduced nicotinamide adenine dinucleotide phosphate, to the detector where it was detected at 340 nm. Under constant potential, the transport velocity of enzyme and the product was generally different. This caused product to be separated from the enzyme after it was formed. Because product formation was much faster than the rate of enzyme-product separation, product accumulated. The amount of accumulated product was inversely related to operating potential. In the extreme case, the operating potential was zero. Zero potential assays were generally carried out by electrophoresing the enzyme partially through the capillary and then switching to zero potential. This capillary was left at zero potential for several minutes to allow additional product to accumulate. After this additional amplification step, potential was again applied and the product transported to the detector. Product formed under constant potential appears as a broad peak with a flat plateau. When the voltage is switched to zero at intermediate migration distance, a peak will be observed on top of this plateau. Either the eight of the plateau or the area of the peak may be used to determine enzyme concentration. The lower limit of detection was 4.6.10(-17) mol of glucose-6-phosphate dehydrogenase.     

A novel capillary electrophoretic method for determining methylglyoxal and glyoxal in urine and water samples

Two non-electroactive biomarkers methylglyoxal (MGo) and glyoxal (Go) in urine and environmental water samples were determined for the first time by capillary electrophoresis with amperometric detection (CE-AD) after derivatizing with an electroactive compound 2-thiobarbituric acid. Experimental conditions of derivatization and CE-AD detection were optimized. Highly linear response was obtained for these two biomarkers over three orders of magnitude with good correlation (r² > 0.999). The limits of detection (LODs) and limits of quantitation (LOQs) of MGo and Go were 0.2 μg L⁻¹ and 1.0 μg L⁻¹, 0.5 μg L⁻¹ and 2.0 μg L⁻¹, respectively. The average recovery and relative standard deviation (RSD) were within the range of 90.9–101.3% and 0.7–2.2%, respectively. The proposed CE-AD method provides a reliable and sensitive quantitative evaluation of MGo and Go in real sample matrices by employing relatively simple and inexpensive instrument.     

On-line monitoring of electroosmotic flow for capillary electrophoretic separations

A recently developed technique for monitoring electroosmotic flow (EOF) in capillary electrophoresis by periodic photobleaching of a neutral fluorophore added to the running buffer has been further characterized and optimized and then applied to monitoring EOF during a typical capillary electrophoresis separation. The concentration of neutral fluorophore (rhodamine B) added to the running buffer for monitoring EOF has been decreased by one order of magnitude. The rate at which EOF can be measured has been increased from 0.2 to 1.0 Hz by decreasing the distance between the bleaching beam and the laser-induced fluorescence detector from 6.13 to 0.635 mm. The precision of the measured EOF ranges from 0.2 to 1.8%. Under typical experimental conditions, the dynamic range for flow measurements is 0.066 to 0.73 cm s(-1). Experimental factors affecting precision, signal-to-noise (S/N) ratio and dynamic range for EOF monitoring have been examined. This technique has been applied to measure EOF during a separation of phenolic acids with analyte detection by UV/VIS absorbance. The EOF monitoring method has been shown not to interfere with UV/VIS absorbance detection of analytes.     

Development and validation of a capillary zone electrophoretic method for the determination of bisphosphonate and phosphonate impurities in clodronate

Capillary zone electrophoresis with direct UV detection at low wavelength and reversed polarity was applied for the separation and quantitation of bisphosphonate and phosphonate impurities in clodronate bulk material. Polyacrylamide-coated capillaries were used to reduce the interactions between the analytes and the electric double layer of the capillary, and to minimize electroosmotic flow. Study was made of the major factors affecting the separation, i.e., pH and ionic strength of the electrolyte solution and various instrumental parameters. The developed method provided reproducible separations of clodronate and related impurities (between-day precision of migration times: RSD < 2.3%, 275 runs). Acceptable validation results in the impurity quantitation range of 0.5-7.5 microg ml(-1) (corresponding to 0.1-1.5% of clodronate working concentration) were obtained in specificity, within-day and between-day precision, accuracy and linearity.     

Oligodeoxynucleotide-modified capillary for electrophoretic separation of single-stranded DNAs with a single-base difference.

We describe here a method of affinity capillary electrophoresis in which oligodeoxynucleotide (ODN) was immobilized onto the inner surface of the capillary. The immobilized ODN functioned successfully as an affinity ligand for sequence-based DNA separation. Six- or 12-mer ODN with a sequence complementary to one of the c-K-ras gene was used as an immobilized ligand. When the 12-mer ODN was used, the detection peak for the complementary ODN disappeared selectively, while the single-base mutant was detected as usual. In contrast, when the 6-mer ODN was used as the affinity ligand with a mixture of the complementary ODN and its single-base mutant, it was possible to detect both as completely separate peaks. That is, the separation mode was dependent on the base number of the immobilized ODN used as an affinity ligand.