Experimental study and modeling of the thermodynamic properties of magnesium silicates

The thermodynamic properties of all MgO-SiO₂ system phases were studied by Knudsen mass spectrometry over a wide temperature range (1571–1873 K) and the whole range of compositions. An approach based on the generation of volatile interaction products formed in the reduction of oxide components was used. The reducing agents were Nb, Ta, and Mo. The observed ion current intensity ratios I(Mg⁺)/I(SiO⁺) were used to calculate the activities and partial thermodynamic functions of the components in liquid and crystalline MgO-SiO₂ mixtures and the integral thermodynamic functions of formation of magnesium ortho-and metasilicates. For the first time, direct and reliable information about the thermodynamic properties of all system phases at high temperatures was obtained. These results in combination with all the available data on the thermodynamic properties and phase equilibria in the MgO-SiO₂ system were used to develop a statistical-thermodynamic model of liquid magnesium silicates based on treating them as associated liquids. Simultaneously, the problem of obtaining self-consistent data on the thermodynamic functions of all phases and conditions of equilibria between them was solved. In addition to polymeric silicon-oxygen structures of arbitrary sizes and spatial configurations, heteromolecular complexes such as MS, M₂S, and M₃S (S=SiO₂ and M=MgO) were found to exist in liquid MgO-SiO₂ mixtures. The correctness of the results obtained was substantiated by the virtually complete coincidence of the calculated thermodynamic properties and phase equilibrium conditions with experimental data and their conformity to the general patterns characteristic of binary silicate systems.     

Propriétés thermodynamiques des mélanges binaires. Volume et énergie interne de formation des solutions de l'hexadécane dans les isomères de l'hexane

The volumes of mixing of hexadecane and each of the isomers of hexane have been measured for the equimolar mixtures at 20°C. The results have been used together with previously measured values of ΔH to obtain ΔU_v. A very good correlation is found between the energy of mixing and the properties of the pure alkanes.     

Measurements and equation-of-state modelling of thermodynamic properties of binary mixtures of 1-butyl-1-methylpyrrolidinium tetracyanoborate ionic liquid with molecular compounds

This paper presents a comprehensive thermodynamic study of binary mixtures formed by 1-butyl-1-methylpyrrolidinium tetracyanoborate ionic liquid and hydrocarbons (n-heptane, benzene, toluene, ethylbenzene), thiophene and alcohols (methanol, ethanol, 1-propanol, 1-butanol, 1-hexanol, 1-octanol, 1-decanol and 1-dodecanol). An impact of chemical structure of molecular compounds on their solubility in the ionic liquid and excess enthalpies of mixing is discussed. Furthermore, modelling of the measured properties by using perturbed-chain statistical associating fluid theory (PC-SAFT) is presented. The theory is applied in both correlative and semi-predictive mode involving temperature-dependent binary corrections fitted to infinite dilution activity coefficients. Solubility curves and excess enthalpies are captured by the model with a reasonable accuracy, when semi-predictive strategy is adopted. Moreover, (liquid + liquid) equilibrium phase diagram in ternary system composed of the investigated ionic liquid, thiophene and n-heptane is predicted with PC-SAFT and then the calculations are confronted with available experimental data. The results indicate that the approach proposed can be perceived as an interesting tool for reproducing the thermodynamic behaviour disclosed by such complex systems as those based on ionic liquids.     

Non‐Ideal Mixing Behaviour of Hydrogen Bonding in Mixtures of Protic Ionic Liquids

Ionic liquids (ILs) attract interest in science and technology as a result of their unique properties. Binary and ternary mixtures of ILs significantly increase the number of possible cation/anion combinations, resulting in targeted physical and chemical properties. In this work, we study the mixing behaviour of two protic ILs: triethyl ammonium methylsulfonate [Et₃NH][CH₃SO₃] and triethylammonium triflate [Et₃NH][CF₃SO₃]. We find a characteristic deviation from ideal mixing by means of low‐frequency infrared spectroscopy. By using molecular dynamics simulations, we explain this behaviour as being the result of different strengths of anion/cation hydrogen bonding. This non‐ideality of non‐random H‐bond mixing is also reflected in macroscopic properties such as the viscosity. Mixing suitable ILs may, thus, result in new ILs with targeted physical properties.     

Viscosities for Ionic Liquid Binary Mixtures with a Common Ion

At present, there is a considerable amount of work devoted to the study of the thermophysical properties of pure ionic liquids, which contrasts with the few data available for their mixtures. One of the most appealing characteristics of ionic liquids is the capability of subtly changing the chemical structure of the cation and anion in order to design appropriate solvents for specific applications. Mixtures of ionic liquids increase enormously this specificity, due to the unlimited combinations that arise from mixing two or more ionic liquids. In this context, the study of the thermophysical properties of these mixtures is revealed as a fundamental task. In this work the viscosities of the ionic liquid binary mixtures with a common ion ([C₆mim] + [C₂mim])[BF₄], ([C₆mim] + [C₄mim])[BF₄], [C₄mim]([BF₄] + [MeSO₄]) and [C₄mim]([PF₆] + [BF₄]) were determined within the temperature range (298.15–308.15) K. The temperature dependence of the viscosity for pure liquids is analyzed by means of the Vogel-Tammann-Fulcher equation and several mixing rules are applied for the mixtures.     

Viscosities and Refractive Indices of Binary Mixtures of Dimethylsulphoxide with Some Aromatic Hydrocarbons at Different Temperatures: An Experimental and Theoretical Study

The viscosities, η, and refractive indices, n, of pure dimethylsulphoxide (DMSO), benzene, toluene, o‐xylene, m‐xylene, p‐xylene and mesitylene, and those of their 54 binary mixtures, with DMSO as common component, covering the whole composition range have been measured at 298.15, 303.15, 308.15, 313.15, and 318.15 K. From the experimental data, the deviations in viscosity, Δη and deviations in molar refraction, ΔR_m have been calculated. The variation of these parameters with composition and temperature of the mixtures have been discussed in terms of molecular interaction in these mixtures. The effect of the number and position of the methyl groups in these aromatic hydrocarbons on molecular interactions in these mixtures has also been discussed. The free energies, ΔG^*, enthalpies, ΔH^* and entropies, ΔS^* of activation of viscous flow have also been obtained by using Eyring viscosity equation. The ΔH^* values were found independent of temperature. The dependence of these thermodynamic parameters on composition of the mixtures has been discussed. Further, the viscosities and refractive indices of these binary mixtures were calculated theoretically from pure component data by using various empirical and semi‐empirical relations and the results were compared with the experimental findings.     

Electrochemical Determination and in silico Studies of Fludarabine on NH2 Functionalized Multiwalled Carbon Nanotube Modified Glassy Carbon Electrode

A sensitive voltammetric technique has been developed for the determination of Fludarabine using amine‐functionalized multi walled carbon nanotubes modified glassy carbon electrode (NH₂‐MWCNTs/GCE). Molecular dynamics simulations, an in silico technique, were employed to examine the properties including chemical differences of Fludarabine‐ functionalized MWCNT complexes. The redox behavior of Fludarabine was examined by cyclic, differential pulse and square wave voltammetry in a wide pH range. Cyclic voltammetric investigations emphasized that Fludarabine is irreversibly oxidized at the NH₂‐MWCNTs/GCE. The electrochemical behavior of Fludarabine was also studied by cyclic voltammetry to evaluate both the kinetic (k_s and E_a) and thermodynamic (ΔH, ΔG and ΔS) parameters on NH₂‐MWCNTs/GCE at several temperatures. The mixed diffusion‐adsorption controlled electrochemical oxidation of Fludarabine revealed by studies at different scan rates. The experimental parameters, such as pulse amplitude, frequency, deposition potential optimized for square‐wave voltammetry. Under optimum conditions in phosphate buffer (pH 2.0), a linear calibration curve was obtained in the range of 2×10^?7 M–4×10^?6 M solution using adsorptive stripping square wave voltammetry. The limit of detection and limit of quantification were calculated 2.9×10^?8 M and 9.68×10^?8 M, respectively. The developed method was applied to the simple and rapid determination of Fludarabine from pharmaceutical formulations.     

Application of Task-specific Ionic Liquids for Intensified Separations

Summary. Ionic liquids offer tremendous opportunities to intensify reactions and separations in process technologies by tuning their physical and chemical properties. Several ionic liquids are suitable for the separation of aromatic and aliphatic hydrocarbons. CO₂ absorption behavior was influenced by the functionalized chains appended to the room temperature ionic liquid (RTIL) cation. Ionic liquids seem able to combine the chemical features of amine solutions with the characteristic advantages of the physical solvents used for CO₂ absorption.     

含CO2/离子液体系统相行为及其在反应与分离中的应用进展

目前已知的绿色溶剂主要包括超临界流体（Supercritical fluids,SCFs）、离子液体（Ionic liquids,ILs）、二氧化碳膨胀液体（CO₂ expanded liquids, CXLs）、水以及上述溶剂的混合物等。其中,由超临界CO₂（Supercritical CO₂,SCCO₂）与ILs混合而构成的新兴溶剂,因为化学热力学方面的特性,成为近年来研究的热点,未来很有发展前景。本文回顾了目前为止在该领域所开展的工作,总结了影响SCCO₂与IL相行为的主要因素。包括温度、压力、ILs的含水量、ILs的阴离子、ILs的阳离子、ILs的摩尔体积以及助溶剂等。同时分析了ILs/SCCO₂与溶质形成的多元混合物相行为的成因。介绍了ILs/CO₂在萃取、反萃取、膜分离、反胶束、萃取与反应耦合等分离方面的应用。由于传统的单元操作很难满足无污染和对过程集成的要求,因而含有ILs/ SCCO₂的分离反应耦合过程将是未来是实现清洁生产的发展方向。     

Application of Task-specific Ionic Liquids for Intensified Separations

Ionic liquids offer tremendous opportunities to intensify reactions and separations in process technologies by tuning their physical and chemical properties. Several ionic liquids are suitable for the separation of aromatic and aliphatic hydrocarbons. CO₂ absorption behavior was influenced by the functionalized chains appended to the room temperature ionic liquid (RTIL) cation. Ionic liquids seem able to combine the chemical features of amine solutions with the characteristic advantages of the physical solvents used for CO₂ absorption.     

X-ray structural studies on microscopic mixing in binary mixtures of dimethyl sulphoxide with acetonitrile and N,N-dimethylformamide

The liquid structures of binary acetonitrile (AN)–dimethyl sulphoxide (DMSO) and N,N-dimethylformamide (DMF)–DMSO mixtures were investigated by the X-ray scattering method. Comparison of the X-ray scattering data of AN–DMSO liquid mixtures with those of neat AN and DMSO revealed that the intermolecular AN–DMSO interactions are practically not detected; that is, the X-ray scattering data of the liquid mixtures are well reproduced by summing up those of neat AN and DMSO weighted by their mole fractions. The same applies for DMF–DMSO mixtures. Thus, each component solvent molecule independently forms self-assembled clusters in the liquid mixtures, the structures of which are the same as those in the neat liquids. The clusters are mixed to form macroscopically homogeneous liquid mixtures. The thermodynamic quantities on mixing process for the AN–DMSO, DMF–DMSO and AN–DMF systems in the literature are well elucidated on the basis of the microscopic structure of the liquid mixtures.     

Radiation-induced synthesis of branched liquid alkanes

The irradiation of gaseous alkane mixtures under circulation conditions was used for the synthesis of liquid branched hydrocarbons. It was found that the synthesized liquid product was a mixture of alkanes with the average molecular weight higher than the molecular weight of the parent gas by a factor of 3–4. The resulting liquids were characterized by boiling range from 35 to 200°C in atmospheric distillation. The average degree of molecular branching in the synthesized liquids was evaluated on the basis of their knock resistance. The octane ratings of liquid mixtures were above 95 (motor octane number) or 103 (research octane number). The fractional composition and detonation properties of the synthesized liquids suggested the prevalence of C₅–C₁₁ isomers with highly branched structures in these liquids. Depending on irradiation conditions, 2,3-dimethylbutane, 2-methylpentane, or 3-methylpentane was predominant among hexanes. As a rule, 2,2,3-trimethylbutane and 2,3-dimethylpentane prevailed among heptanes.     

Enthalpies of solution of <Emphasis Type="Italic">n</Emphasis>-alkanes in mixtures of MeCN with alkan-1-ols at 298.15 K. Relations between the thermodynamic properties of binary and ternary systems

The solution enthalpies of n-hexane, n-nonane, and n-undecane in mixtures of MeCN with EtOH, PrOH, and BuOH were determined by calorimetric method at 298.15 K. Relations between the thermodynamic properties of ternary systems and the properties of the binary solvents and the solute are discussed. To predict the enthalpies of solution of hydrocarbons in mixed solvents whose components have strongly different molar volumes (V ₂/V ₁ > 1.5), it is proposed to use the values that are additive in the volume fraction scale. The solution enthalpies of hydrocarbons in mixtures characterized by close molar volumes of the components strongly depend on the excess properties of the binary solvent.Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1578–1582, August, 2004.     

Refractive Index of Liquid Mixtures: Theory and Experiment

An innovative approach is presented to interpret the refractive index of binary liquid mixtures. The concept of refractive index “before mixing” is introduced and shown to be given by the volume‐fraction mixing rule of the pure‐component refractive indices (Arago–Biot formula). The refractive index of thermodynamically ideal liquid mixtures is demonstrated to be given by the volume‐fraction mixing rule of the pure‐component squared refractive indices (Newton formula). This theoretical formulation entails a positive change of refractive index upon ideal mixing, which is interpreted in terms of dissimilar London dispersion forces centred in the dissimilar molecules making up the mixture. For real liquid mixtures, the refractive index of mixing and the excess refractive index are introduced in a thermodynamic manner. Examples of mixtures are cited for which excess refractive indices and excess molar volumes show all of the four possible sign combinations, a fact that jeopardises the finding of a general equation linking these two excess properties. Refractive indices of 69 mixtures of water with the amphiphile (R,S)‐1‐propoxypropan‐2‐ol are reported at five temperatures in the range 283–303 K. The ideal and real refractive properties of this binary system are discussed. Pear‐shaped plots of excess refractive indices against excess molar volumes show that extreme positive values of excess refractive index occur at a substantially lower mole fraction of the amphiphile than extreme negative values of excess molar volume. Analysis of these plots provides insights into the mixing schemes that occur in different composition segments. A nearly linear variation is found when Balankina’s ratios between excess and ideal values of refractive indices are plotted against ratios between excess and ideal values of molar volumes. It is concluded that, when coupled with volumetric properties, the new thermodynamic functions defined for the analysis of refractive indices of liquid mixtures give important complementary information on the mixing process over the whole composition range.     

Determination of column selectivity toward polycyclic aromatic hydrocarbons

An empirical test is described for the evaluation of column selectivity in reversed-phase liquid chromatography. Using a test mixture of three polycyclic aromatic hydrocarbons (PAH), overall column selectivity toward PAH was assessed for over 20 different commercial C₁₈ columns. Retention behavior was correlated to phase type (i.e., monomeric and polymeric surface modification chemistry) for custom synthesized phases. A classification scheme is proposed in which commercial C₁₈ columns are grouped into three classes based on retention behavior: monomeric-like, polymeric-like, and intermediate phase selectivity toward PAH. Correlation of retention behavior of the test mixture with the separation of PAH mixtures and with more general column properties (e.g., phase thickness) is discussed.     

Electron-beam radiolysis of gaseous alkanes under circulation conditions: Gas-to-liquid transformation

The circulating mode of electron-beam irradiation was used for synthesis of the branched liquid hydrocarbons from the gaseous alkane mixtures, including natural gas and the associated petroleum gas. Atmospheric distillation of resulting liquids was characterized by boiling point range from 36 up to 200–230 °C. The average degree of molecular branching in the synthesized liquids was evaluated on the basis of their antiknock characteristics. The octane values of liquids synthesized from natural gaseous mixtures were above 95. The fractional composition and antiknock characteristics of synthesized liquids suggested the prevalence of C₅–C₁₁ isomers with highly branched structures. Fractional and isomeric compositions of the liquid products depended on the gas-phase composition, dose rate, and gas-dynamic conditions in the irradiation area.     

Conformational energy contribution to the heat of solution in polymer–solvent systems. Part II. Experimental results

Heats of solution (ΔH_exp) in solvents of increasing thermodynamic power have been measured for four polymers: polystyrene (PS), poly(vinyl acetate) (PVAc), polyisobutylene (PIB) and polydimethylsiloxane (PDMS). After subtraction from ΔH_exp of an interaction term (calculated by the Hildebrand treatment based on solubility parameters) and the excess volume term, the quantity remaining is interpreted as the conformational energy contribution (ΔU_conf) to the heat of solution. ΔU_conf appears to correlate well with some basic conformational properties of the chain, such as the sign of the temperature coefficient of unperturbed dimensions derived from solution properties, and shows a monotonic behavior with α, the expansion coefficient of the polymer coil in the final solution. Numerical values of ΔU_conf, at least for those cases in which polymer solubility parameters are known with some certainty, are much larger than those evaluated from rubber elasticity experiments (through the experimentally accessible value of the energy component of the force of retraction im simple elongation).     

Equilibrium anionic polymerization of β-methoxypropionaldehyde

Anionic polymerization of β-methoxypropionaldehyde (MPA) was carried out in tetrahydrofuran (THF) by using benzophenone–monolithium complex as an initiator. An equilibrium between polymerization and depolymerization was observed at a temperature range of ?90 to ?70°C. From the temperature dependence of the equilibrium monomer concentration, thermodynamic parameters for the polymerization of MPA in THF were evaluated as follows: ΔH_ss = ?4.8 ± 0.2 kcal/mole, ΔH_SS = ?22.4 ± 1.3 cal/mole-deg, and (T_c)_ss = ?59°C. The thermodynamic change upon the conversion of liquid monomer to condensed polymer was computed from both the partial mixing energy of MPA with THF and the linear relationship between the equilibrium volume fraction of MPA monomer and that of the resulting polymer: ΔH_1c = ?4.7 ± 0.2 kcal/mole, ΔS_1c = ?19.5 ± 1.3 cal/mole-deg, and (T_c)_1c = ?35°C.     

Conductance study of the thermodynamics of micellization of 1-hexadecylpyridinium bromide in mixed solvents containing dilute electrolyte solutions

The critical micelle concentration (CMC) of hexadecylpyridinium bromide (HDPB) is determined conductometrically in binary mixtures of water + cosolvent at various temperatures and at low concentrations of sodium bromide, ranging from 0 to 2.4 × 10^?2 M. Dimethylsulfoxide (DMSO) and acetonitrile (AN) were used as cosolvents added to water. The ability of NaBr to lower the CMC of HDPB in water is inhibited by DMSO and AN. Thermodynamic parameters of micellization ΔH_m ^o, ΔS_m ^o, and ΔG_m ^o are evaluated according to the pseudo-phase model. The contribution of DMSO and AN in the micellization process of HDPB in aqueous electrolyte solutions are discussed in terms of the observed thermodynamic properties.     

On the heat of solution of polymer with solvent: Polydimethylsiloxane–solvent systems

Heats of mixing and excess volumes at infinite dilution have been obtained at 25°C. for polydimethylsiloxane or its lower oligomers in various solvents by using a twin conduction microcalorimeter and from the pycnometric specific volumes. From those values, excess energies ΔE^M_v at constant volume have been determined. The prediction on intramolecular conformation contributions to the heat of solution as proposed by Bianchi has been evaluated by the values of ΔE^M_v. The heat of solution in the polymer–solvent systems was interpreted by the expression for ΔE^M_v derived from the Van Laar-Hildebrand work on simple liquid mixtures with the solubility parameters of polymers obtained from indirect measurements. The values of conformational intramolecular energy change calculated from dilute solution properties were difficult to rationalize with our results. Our present results suggest that systems in a nonideal state can not be distinguished for certain from those in the ideal state. This conclusion based on apparent values does not deny the possible effect of the conformational energy change.