十六烷基三甲基溴化铵修饰碳糊电极线性扫描伏安法测定尿液中尿酸

本文提出了以十六烷基三甲基溴化铵修饰碳糊电极（CTAB／CPE）直接测定尿酸（UA）的新方法,用线性扫描伏安法（LSV）研究尿酸的电化学行为。在0.1mol／L磷酸盐缓冲溶液（PBS,pH=7.4）中,尿酸在CTAB／CPE上于0.160V处产生一个灵敏的氧化峰,氧化峰电流Ip与尿酸浓度（CuA）在1.0×10^-5—1.0×10^-3mol／L范围内呈良好的线性关系,相关系数为0.9940,检出限为1.0×10^-6mol／L。该方法简单实用,可以直接用于人体尿液中尿酸的检测。     

The influence of cetyltrimethyl ammonium bromide on electrochemical properties of thyroxine reduction at carbon nanotubes modified electrode

The effect of cetyltrimethyl ammonium bromide (CTAB) on the electrochemical behaviors of thyroxine at a glassy carbon electrode (GCE) modified with single-walled carbon nanotubes (SWNTs) was investigated. At the SWNTs film-coated GCE, a well-defined oxidation peak of thyroxine at 0.78 V was obtained, but the reduction peak of thyroxine was indiscernible. When trace CTAB was added to the working solution, the reduction current could be greatly enhanced and the oxidation current remained stable. The reaction mechanisms for the reduction of thyroxine were explored by chronocoulometry. Thyroxine might form particular ion complex with CTAB via the interaction between iodine atoms on thyroxine and bromide ions in CTAB, which made the concentration of thyroxine at the surface of the modified electrode increased and the electron transfer rate enhanced. The proper mechanisms for the enhanced reduction of thyroxine in the present of CTAB were explored by several electrochemical techniques including cycle voltammetry linear sweep voltammetry and others. It was concluded that the special interactions between the thyroxine CTAB and SWNTs resulted in the increase of the reduction peak current. All results indicated that two iodine atoms on the thyroxine and four electrons were involved the reduction process which was irreversible and two iodine ions produced. In this system, the sensitive reduction peak of thyroxine at 0.3 V was employed to determine thyroxine and a low detection limit of 2x10(-8) mol/L was obtained for 2 min accumulation at 0.9 V. The SWNTs coated GCE had good stability and reproducibility.     

Carbon paste electrode based on surface activation for trace adriamycin determination by a preconcentration and voltammetric method.

A voltammetric determination of adriamycin (ADM) at a carbon paste electrode (CPE) in the presence of cetyltrimethylammonium bromide (CTAB) is described. ADM strongly adsorbs on the surface of the electrode by the adsorption of CTAB, thereby affecting the reduction current. This method provides a detection limit below 10(-10) mol/L for ADM. The experimental parameters, which influence the voltammetric responses of ADM, e.g. the pH value, variety and concentration of surfactants and the scan rate, were optimized. The reduction peak current changes linearly with the ADM concentration over the range from 2.5 x 10(-8) mol/L to 5 x 10(-6) mol/L. The detection limit is 4 x 10(-10) mol/L for an accumulation time of 3 min. The coefficient of variation, determined at 4 x 10(-6) mol/L ADM, is 3.0% (n = 8). Using this method, ADM in the patient's urine samples, which undergoes active ADM chemotherapy, was determined.     

High sensitivity voltammetric determination of sodium nitroprusside at acetylene black electrode in the presence of CTAB

A sensitive electroanalytical method for detection of sodium nitroprusside (SNP) was investigated, on the basis of the enhanced electrochemical response of SNP at an acetylene black electrode (ABE) in the presence of cetyltrimethylammonium bromide (CTAB). Voltammetric studies showed that SNP exhibited a pair of quasi-reversible redox peaks at ABE in the presence of CTAB while no any redox peak was observed in the absence of CTAB. This was attributed to the enhanced adsorption of SNP at AB through electrostatic interactions between SNP and CTAB as well as hydrophobic adsorption of CTAB at the hydrophobic surface of ABE. Under optimal working conditions, the reduction current was proportional to the concentration of SNP in the range of 1.0x10(-7) to 1.0x10(-5) mol/L and 1.0x10(-5) to 1.0x10(-2) mol/L. A low detection limit of 5.0x10(-9) mol/L was obtained for 2 min accumulation at open circuit (S/N=3). The proposed method was successfully applied to the determination of SNP in pharmaceutical dosage forms.     

Carbon paste electrode for trace zirconium(IV) determination by adsorption voltammetry.

A very sensitive and selective procedure was developed for trace measurement of zirconium based on the cathodic adsorptive stripping voltammetry of the zirconium-alizarin red S(ARS) complex at a carbon paste electrode (CPE). The 2nd-order derivative linear scan voltammograms of the zirconium-ARS complex were recorded by a model JP-303 polarographic analyzer from 0.0 to -1.0 V (vs. SCE). Optimal analytical conditions were found to be: an acetic acid (0.1 mol l(-1))-potassium biphthalate (0.08 mol l(-1)) buffer solution (pH 4.8) containing 4.0 x 10-6 mol l(-1) ARS; accumulation potential, 0.0 V; accumulation time, 180 or 90 s; rest time, 10 s; scan rate, 250 mV s(-1). The results showed that the complex can be adsorbed on the surface of the CPE, yielding one peak at -0.51 V, corresponding to the reduction of ARS in the complex at the electrode. The detection limit was found to be 1.0 x 10(-10) mol l(-1) (S/N = 3) for 240 s accumulation. The linear range was 2.0 x 10(-10)-4.0 x 10(-7) mol l(-1). The developed method was applied to the determination of trace zirconium in the ore samples with satisfactory results.     

三辛胺修饰碳糊电极测定电子引脚中的Cr(Ⅵ)

采用三辛胺(TOA)修饰碳糊电极(TOA/CPE)测定了Cr(Ⅵ)含量,并考察了最佳的实验条件。当富集时间为10 min,富集介质为0.15 mol/L H2SO4时,TOA/CPE能够有效地富集Cr(Ⅵ)。以溶出伏安法测定Cr(Ⅵ),在-0.45 V(vs.SCE)处有灵敏的还原峰,峰电流与Cr(Ⅵ)浓度在5.0×10-7~1.0×10-3mol/L范围内呈现良好的线性关系。干扰试验显示TOA/CPE对Cr(Ⅵ)具有高选择性,能够在Cr(Ⅲ)浓度是Cr(Ⅵ)600倍时准确测定Cr(Ⅵ),检出限达3.4×10-9mol/L(S/N=3)。TOA/CPE测定了实际样品电子引脚中的Cr(Ⅵ),实验结果与紫外分光光度法结果一致。     

基于表面活性剂单分子层修饰碳糊电极的一氧化氮电化学传感器及其应用

报道了一种表面活性剂单分子层修饰碳糊电极,并用于NO的高灵敏电化学检测。研究表明,表面活性剂通过烷基链在电极表面形成的疏水性单分子层微环境对NO的电化学响应具有较好的促进作用。其中,阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)对NO的电化学氧化表现出最强的催化活性和增敏作用。在Nafion膜覆盖的CTAB修饰碳糊电极上,NO的安培响应与其浓度在3.6×10-8～1.8×10-5mol/L范围内呈良好的线性关系,检出限为1.8×10-8mol/L。该电极作为低成本、高灵敏的NO电化学传感器,被成功应用于大鼠肺组织细胞中NO释放的实时监测。     

Mechanism of oxidation of 1-benzyl-1,4-dihydronicotinamide by the biologically active p-benzoquinone derivative, avarone, in a cationic micellar medium: An electrochemical approach

The electrochemical reduction of avarone (Q), an antitumor sesquiterpenoid quinone, was investigated at various pH in aqueous ethanol containing a cationic surfactant, cetyltrimethylammonium bromide (CTAB) by cyclic and rotating disc electrode voltammetry, using a glassy carbon electrode. Comparison of the electrochemical reduction of Q in presence of CTAB with the same process in a homogeneous water + ethanol solution shows an anodic shift of the reduction potential in the presence of CTAB; at pH > 9.5 and in presence of CTAB, two well-defined reduction peaks are observed, thus confirming one-electron reduction of Q, whereby the intermediate radical-anion is stabilized by the cationic micellar medium. The electrochemical oxidation of BNAH was investigated by cyclic voltammetry, and the anodic shift of the peak potential in presence of CTAB was observed. From the electrochemical behaviour of Q and BNAH, and the kinetics of the oxidation of BNAH with Q, it is suggested that the reaction takes place in two successive one-electron transfer steps. The application of the Marcus theory gives additional proof that, in this case, the first electron transfer is the rate determining step.     

γ-Oryzanol-loaded calcium pectinate microparticles reinforced with chitosan: Optimization and release characteristics

The cationic surfactant, cetyltrimethyl ammonium bromide (CTAB) effect on accurate determination of dopamine in the presence of ascorbic acid (as natural obtrusive in determination of dopamine) using chemically modified electrode based on tin hexacyanoferrate (SnHCF) as a modifier at carbon paste electrode (CPE) is described. The electrochemical response of bare CPE and SnHCF modified electrode (ME) examined in different pHs, in absence and presence of different concentration of dopamine (DA) and ascorbic acid (AA). In addition a simple and reliable method for simultaneous electrochemical determination of AA and DA was presented. It was based on the use of the cationic surfactant CTAB that enables the separation of the oxidation peaks potential of AA and DA. The experimental results showed that DA and AA have two separate peaks. In pH 3 and at presence of 3 mM of CTAB the separation of DA and AA peaks and the eminence of them increased evidently. Good linear response to AA and DA was observed in the range of 0.4–50 and 0.2–25 mM with the correlation of 0.9912 and 0.9955, respectively.     

Direct Electrochemistry of Hemoglobin Immobilized in Sodium Alginate Film on the Ionic Liquid [BMIM]PF6 Modified Carbon Paste Electrode

In recent years the direct electron transfer of redox protein on electrode surface has attracted great attentions1. Different kind of modified electrode and various supporting films for immobilization of proteins had been proposed. But most of them are ba…     

Electrochemical determination of dipyridamole at a carbon paste electrode using cetyltrimethyl ammonium bromide as enhancing element

Electrochemical behaviors of dipyridamole (DIP) at a carbon paste electrode in the presence of cetyltrimethyl ammonium bromide (CTAB) were investigated by voltammetry, chronocoulometry and electrochemical impedance spectroscopy (EIS). The results indicated that the electrochemical responses of DIP are apparently improved by CTAB, due to the enhanced accumulation of dipyridamole at the carbon paste electrode surface. Electrochemical parameters for the oxidation of DIP were explored by chronocoulometry. Under optimal conditions, the oxidation peak current at 0.53 V was proportional to DIP concentration in the range of 0.03-12 microg mL-1, with a detection limit of 0.01 microg mL-1 for 120 s accumulation by different pulse voltammetry (DPV). This method was applied to the determination of DIP in the tablet samples. The results were satisfying compared with that obtained by standardized method of high performance liquid chromatography (HPLC).     

Effects of surfactants on the electroreduction of dioxygen at an acetylene black electrode.

An acetylene black electrode modified by an adsorbed cationic surfactant, cetyltrimethylammonium bromide (CTAB), was developed. The influences of various types of surfactants on the electroreduction of O2 were investigated. It was demonstrated that a cationic surfactant, CTAB, on the surface of the electrode could significantly decrease the overpotential of dioxygen reduction, and the reduction peak current of O2 was also remarkably increased. The reduction of O2 at a CTAB modified acetylene black electrode was studied using cyclic voltammetry, chronocoulometry and controlled potential coulometry. The total number of electrons, the exchange current density (j(o)) and the transfer coefficient (alpha) for reduction of O2 at the surface of this modified electrode were determined.     

Sensitive spectrophotometric method for trace amounts of uranium

A sensitive spectrophotometric method for the determination of uranium with Pyrogallol Red (PGR) and cetyltrimethylammonium bromide (CTAB) is described. The sensitivity of the colour reaction between uranium and Pyrogallol Red is greatly increased in the presence of cetyltrimethylammonium bromide. The blue ternary complex (λ_max580 nm) has composition 1:2:4 [U(VI):PGR:CTAB] at pH 5.6. Beer's law is obeyed over the range 19.0-0.24 ppm of uranium and the molar absorptivity is 3.3 × 10⁴ l.mole⁻¹.cm⁻¹ at 620 nm. A tentative structure for the ternary complex is suggested. A simple method is suggested for evaluation of stability constants of such ternary complexes.     

Aqueous Electrochemistry of Anthraquinone and Its Correlation with the Dissolved States of a Cationic Surfactant

Cyclic voltammetry was employed to study the electrochemical behavior of anthraquinone (AQ) in aqueous solution at a glassy carbon electrode using the sodium salt of anthraquinone-2-sulphonic acid (AQS). The cyclic voltammograms show a reduction wave and a corresponding oxidation wave. The electrochemical reaction of AQ in aqueous solution involves a two electron transfer process followed by a coupled chemical reaction and exhibits strong pH dependence at low pH (<4). A satellite peak is also observed at the cathodic side of the reduction wave for the reduction of the sulfonate group of AQS. The electrochemical investigation was also carried out in the presence of a cationic surfactant, cetyltrimethylammonium bromide (CTAB). Similar redox behavior can be observed for the electrochemical reaction of AQS in the presence of CTAB solutions similar to the aqueous media. The electrochemical responses have been found to depend on the dissolved states of the surfactant. The current-potential behavior of AQS depends on the concentration of CTAB and micellization has a profound effect on the electrochemical behavior of AQ.     

石墨烯/十二烷基硫酸钠复合物修饰碳糊电极测定氯霉素

以液体石蜡和硅油为混合粘合剂,与石墨粉混合制备了碳糊电极基底电极,将石墨烯/十二烷基硫酸钠复合物修饰在基底碳糊电极上,得到了基于石墨烯复合物的新型修饰碳糊电极。应用扫描电镜和循环伏安法分别研究了该电极的表面特性和电化学性质,结果表明,石墨烯和十二烷基硫酸钠修饰的碳糊电极增大了比表面积,有利于电子传递。在pH 3.0的HAc-NaAc缓冲溶液中,该修饰碳糊电极对氯霉素具有良好的电化学响应,氧化峰电位为0.194 V,氧化峰电流是基底碳糊电极的10倍。在最优实验条件下,该氧化峰电流与氯霉素的浓度在1.0×10~(-8)~5.0×10~(-4)mol/L范围内呈良好的线性关系,检出限为5.0×10~(-9)mol/L。该方法简便,重现性及选择性好,用于测定氯霉素滴眼液和虾中氯霉素残留,结果满意。     

Electrochemical behavior of phenol at acetylene black-dihexadecyl hydrogen phosphate composite modified glassy carbon electrode in the presence of cetyltrimethylammonium bromide

The electrochemical response of phenol at acetylene black (AB)-dihexadecyl hydrogen phosphate (DHP) composite modified glassy carbon electrode in the presence of cetyltrimethylammonium bromide (CTAB) was investigated. In this system, a sensitive oxidation peak at 0.62 V (SCE) was obtained. The electrode process and the influence of CTAB on the oxidation of phenol were explored by chronocoulometry and linear sweep voltammetry (LSV). Experimental conditions for the determination of phenol were optimized. In the range of 5.0 × 10⁻⁷ to 1.2 × 10⁻⁵ M, the phenol concentration was linear with the oxidation peak current and the detection limit was found to be 1.0 × 10⁻⁷ M for 3 min accumulation. The method was applied for the determination of phenol in lake water and the results were satisfactory. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 2, pp. 222–229. The text was submitted by the authors in English.     

碳糊电极阴极吸附伏安法测定橙皮甙

在0.4mol/L的NH4Cl-NH3(pH9.0)缓冲液中,使用JP-303极谱分析仪,橙皮甙在碳糊电极(CPE)上有一灵敏的吸附伏安还原峰,峰电位为-1.2V(vs.SCE).该还原峰的二阶导数峰电流与橙皮甙的浓度在2.0×10-8～1.0×10-6mol/L(富集90s)范围内成良好的线性关系,相关系数为0.9963,检出限为1.0×10-8mol/L(S/N=3,富集110s).探讨了橙皮甙在碳糊电极上的伏安性质和电极反应机理,并且成功应用于中草药桔皮中橙皮甙含量的测定.     

Voltammetric determination of antibacterial drug gemifloxacin in solubilized systems at multi-walled carbon nanotubes modified glassy carbon electrode

A sensitive electroanalytical method for determination of gemifloxacin in pharmaceutical formulation has been investigated on the basis of the enhanced electrochemical response at multi-walled carbon nanotubes modified glassy carbon electrode in the presence of CTAB. Solubilized system of different surfactants including SDS, Tween-20 and CTAB were taken for the study of electrochemical behaviour of gemifloxacin at modified electrode. The reduction peak current increases in the presence of CTAB while other surfactants show opposite effect. The modified electrode exhibits catalytic activity, high sensitivity, stability and is applicable over wide range of concentration for the determination of gemifloxacin. The mechanism of electrochemical reduction of gemifloxacin has been proposed on the basis of CV, SWV, DPV and coulometeric techniques. The proposed squarewave voltammetric method shows linearity over the concentration range 2.47-15.5 μg/mL. The achieved limits of detection (LOD) and quantification (LOQ) are 0.90 ng/mL and 3.0 ng/mL respectively.     

Electrochemical evaluation of the desloratadine at bismuth film electrode in the presence of cationic surfactant: Highly sensitive determination in pharmaceuticals and human urine by Linear sweep-cathodic stripping voltammetry

In this study, the electrochemical properties of desloratadine, which is in the second generation antihistamines group, were determined by bismuth film electrode (BiFE) in aqueous and aqueous/surfactant solutions. This compound gave an irreversible and diffusion-controlled reduction peak at about –1.65 V by cyclic voltammetry. It was found that the addition of cationic surfactants (cetyltrimethylammonium bromide (CTAB) increased the reduction current signal of desloratadine, while anionic (sodium dodecylsulfate (SDS) and nonionic (Tween 80) surfactants were found to have an adverse effect. Using linear sweep-cathodic stripping voltammetry, the analytical signal showed a linear correlation with a concentration of 0.1 to 4 µM in 0.04 M Britton–Robinson solution (pH = 8.0) in the presence of 5 mM CTAB, while the detection limit was calculated to be 11.70 nM (3.64 μgL^–1). This method has been successfully applied for the quantitation of desloratadine in pharmaceutical and urine samples without the need for any separation.     

Sensing System Integrating Lanthanum Hydroxide Nanowires with Copper(II) Ion for Uracil and its Application

Abstract

A sensing system for uracil was constituted by using lanthanum hydroxide nanowires (LNW) as a modifier to obtain LNW modified carbon paste electrode (LNW/CPE) and by introducing copper(II) ion into supporting electrolyte to transform electroinactive uracil to electroactive uracil‐Cu(II) complex. The voltammetric behaviors of uracil in the presence of Cu(II) ion at LNW/CPE were investigated. A reduction peak of the uracil‐Cu(II) complex at ?0.18 V was the two‐electron reduction of Cu(II) ion in the uracil‐Cu(II) complex; while a new oxidation peak at 0.22 V was the one‐electron oxidation of the uracil‐Cu(I) complex. Additionally, the voltammetric responses of all the complexes at LNW/CPE were more sensitive than that at carbon and multiwall carbon nanotube paste electrodes, which resulted from both the large surface effect of LNW and the chemical coordination of uracil with La(III) ion in LNW. With the sensitive oxidation peak of the uracil‐Cu(I) complex at LNW/CPE, a linear range of 4.0×10^?9?3.0×10^?8 mol/l for uracil was obtained along with a detection limit of 2.0×10^?10 mol/l. The proposed system was evaluated by the determination of uracil derivatives, anticancer drug 5‐flurouracil, in pharmaceutical preparations.