High Activity SnO2／Al2O3 Catalyst for NO Reduction in the Presence of Oxygen

The novel sol-gel SnO2/Al2O3 catalysts for selective catalytic reduction NO by propene under lean burn condition were investigated. The results showed thatthe maximum NO conversion was 82% on the SnO2/Al2O3 (5%Sn) catalyst, and the presence of H20 and SO2 improved the catalytic activity at low temperature. The catalytic activity of NO2 reduction by propene is much higher than that of NO at the entire temperature range, and the maximum NO2 conversion reached nearly 100% around the temperature 425℃.     

具有良好热稳定性的Al2O3改性Fe2O3基金催化剂

通过共沉淀法和沉积-沉淀法制备出了具有良好热稳定性的Al2O3改性Fe2O3基金催化剂, 并通过透射电镜(TEM)、X射线衍射(XRD)、N2吸附-脱附及热重和差示扫描量热(TG-DSC)分析等表征手段对催化剂的结构与表面形貌进行了研究分析. TEM测试结果表明: 500 ℃焙烧后, 未掺杂Al2O3的催化剂中金颗粒粒径分布较宽, 平均粒径约为7.0 nm, 载体颗粒尺寸在50-100 nm范围内; 而掺杂Al2O3的催化剂中金颗粒粒径分布变窄, 平均粒径约为5.0 nm, 且载体颗粒大小也明显小于未掺杂Al2O3的催化剂, 保持在30-50 nm的范围内. N2吸附-脱附测试结果表明, Al2O3的掺杂有利于保持催化剂的介孔结构和比表面积, 从而提高了载体的热稳定性. XRD和TG-DSC测试结果表明, Al2O3的掺杂可以有效地抑制Fe2O3的结晶, 进而抑制了高温焙烧过程中金颗粒的长大. 选用CO低温氧化反应对催化剂的活性进行了评价, 即使在500 ℃高温下焙烧12 h, 掺杂了Al2O3的催化剂仍然可在26.7 ℃将CO完全转化, 而未掺杂Al2O3的催化剂CO最低完全转化温度(T100)高达61.6 ℃. Al2O3的掺杂显著提高了催化剂的热稳定性能.     

Pt/Al2O3和Pt-Cu/Al2O3催化CCl4氢化脱氯反应

制备了Al2O3负载Pt单金属催化剂和负载Pt-Cu双金属催化剂,比较了二者不同还原温度对其催化CCl4氢化脱氯反应性能的影响。 单金属Pt催化剂上主要生成CHCl3,而双金属Pt-Cu催化剂上产物随催化剂制备时的还原温度不同而异,当催化剂经400 ℃用H2还原后产物主要为CHCl3,而当催化剂经800 ℃用H2还原后产物主要为CCl2CCl2。 由于CCl4氢化反应是强放热反应,催化剂表面局部过热使得在反应中生成的C2等产物聚合结焦,覆盖了催化剂的活性中心,导致催化剂失活。 因此,通过加入甲醇作为稀释剂以带走部分反应热可提高催化剂的稳定性。 同时也降低了CHCl3的选择性,提高了CCl2CCl2的选择性。     

热压烧结制备Al2O3/TiCN-0.2%Y2O3复合材料

采用热压烧结的方法制备Al2O3/TiCN-0.2%Y2O3复合陶瓷的结果, 较详细地介绍了试样成分、热压温度对试样抗弯强度、断裂韧性、维氏硬度等力学性能的影响. 结果表明 在热压温度低于1650 ℃时, 各项力学性能随着热压温度的提高而提高, 当热压温度为1650 ℃、压力为35 Mpa, 保温时间为30 min时, 其抗弯强度、断裂韧性及硬度分别达到它们的最大值1015 Mpa, 6.89 Mpa·m1/2和20.82 Mpa. 当热压温度高于1650 ℃时, 导致 TiCN分解作用加强导致密度下降, 同时温度过高导致晶粒长大使力学性能下降. 显微结构分析表明 由于稀土Y2O3的加入, 生成少量的YAG相, 抑制了Al2O3和TiCN晶粒长大, 有助于提高含Y2O3的Al2O3/TiCN复合材料的断裂韧性. TiCN颗粒弥散在Al2O3晶界处, 其晶粒尺寸在1 μm左右, 分布均匀, 相互交织, 抑制了晶粒生长, 从而起到增韧补强作用, 有利于材料力学性能的提高. 从压痕裂纹尖端扩展情况的扫描电镜照片可以看出 基体与增强相多个晶粒构成裂纹桥联行为, 并可能形成裂纹偏转、分支与桥联的共存区, 主要起作用的是稀土强化TiCN颗粒弥散增韧机制, 将复合材料的断裂韧性从5.94提高到6.89 Mpa·m1/2.     

固体超强酸SO2-4/SnO2-Al2O3的红外光谱研究

以四氯化锡、硫酸铝为原料,氨水为沉淀剂,采用共沉淀法制得新型固体超强酸SO2-4/SnO2-Al2O3.采用FT-IR技术考察了金属元素摩尔比、焙烧温度、浸渍液以及掺杂稀土氧化物对该固体超强酸结构和性能的影响.FT-IR结果表明在该固体超强酸中,锡和硫酸根是以螯合和桥式两种方式配位结合,其中起催化活化作用的主要是和硫酸根以螯合双齿结合的锡;和SO2-4/ZrO2型超强酸相比,SO2-4/SnO2-Al2O3超强酸的硫酸根FT-IR特征吸收峰发生蓝移,显示出更强的酸性.锡铝摩尔比为9∶1、焙烧温度为773K、焙烧时间为3h时,制得的SO2-4/SnO2-Al2O3样品对酯化反应的催化性能最好.     

Enhancement of Activity of SnO2-doped In2O3/Al2O3 Catalyst for NO Reduction with Propene in the Presence of H2O and SO2

The selective catalytic reduction of nitrogen oxides by hydrocarbons (HC-SCR) has attracted much attention as an efficient way to remove NO in the presence of excess oxygen1-2. The metal oxides are the most promising catalysts for the SCR of NO because of their high activity and selectivity3-5. In the previous work, the metal oxides such as Ag, Sn, In, Co supported on alumina for NO reduction were investigated6-8, however, the HC-SCR is usually suppressed in the presence of H2O and S…     

Activity Enhancement of Pt/Ba/Al2O3 Mixed with Mn/Ba/Al2O3 for NOx Storage-reduction by Hydrogen

The storage and reduction of nitrogen oxides has attracted much attention as an efficient way to reduce NOx emission of lean-burn gasoline and diesel engines1-5. At present, NOx storage and reduction (NSR) catalysts based on Pt and Ba have been extensivel…     

Synthesis and characterization of Al2O3/Cr2O3-based ceramic pigments

The synthesis and the characterization of Al₂O₃-based nanocrystalline inorganic pigments are reported. The pigments were synthesized by the polymeric precursor (Pechini method) using Cr₂O₃ as chromophore. XRD results only evidenced the corundum phase. The average particle size was about 34 nm. The samples were also characterized by differential scanning calorimetry (DSC) and thermogravimetry (TG), and CIE-L*a*b* calorimetry. The pigments obtained in this work presented different colors, ranging from green to rose. This revised version was published online in August 2006 with corrections to the Cover Date.     

不同含量Y2O3的ZrO2对Al2O3复合陶瓷热震稳定性的影响

含2% (摩尔分数) Y2O3的ZrO2 (简称TZP(2Y)) 和3% (摩尔分数) Y2O3的ZrO2 (简称PSZ(3Y)) 分别以15%(体积分数)添加到Al2O3基体中, 经1550 ℃真空烧结.实验表明, Al2O3复合材料的性能均高于单相Al2O3陶瓷, 并且Al2O3/PSZ(3Y)的抗热震性优于Al2O3/TZP(2Y). 提高改善复合材料的抗热震性是ZrO2(Y2O3)多种增韧机制的作用. 理论计算表明, Al2O3陶瓷和Al2O3/TZP(2Y), Al2O3/PSZ(3Y)复合材料的断裂功分别为38, 100.8, 126.2 J·m-2. Al2O3/TZP(2Y) 和 Al2O3/PSZ(3Y)复合材料的裂纹萌生阻力是Al2O3陶瓷的1.41倍和1.57倍, 而裂纹扩展阻力是Al2O3陶瓷的1.38倍和1.46倍, 与热震实验残余强度的结果一致.     

CuO/Al2O3脱硫反应单颗粒模型化研究

针对氨再生CuO/Al2O3脱硫反应只发生在固体内外表面的CuO上这一特性,在粒子模型基础上,建立了描述氨再生CuO/Al2O3脱硫的单颗粒数学模型,并在热重分析仪上进行了CuO/Al2O3颗粒脱硫反应动力学的研究,将反应过程中CuO逐步变为CuSO4、孔隙率逐渐减小及气相SO2的有效扩散系数逐渐降低的现象用经验式De=α（1-x）b表达,从而使结构变化对反应的影响在颗粒模型中体现出来。模型预测与实验结果吻合良好。数值分析表明,孔扩散对CuO/Al2O3颗粒脱硫反应进程起重要作用,扩散活化能随反应的进行而增大。     

甲烷部分氧化制合成气反应Pt/Al_2O_3和Pt/CeO2/Al_2O_3催化剂的研究(英文)

研究了Ｐｔ／Ａｌ２Ｏ３和Ｐｔ／ＣｅＯ２／Ａｌ２Ｏ３催化剂对甲烷部分氧化制合成气反应的催化活性，发现Ｐｔ／ＣｅＯ２／Ａｌ２Ｏ３显示了比Ｐｔ／Ａｌ２Ｏ３更高的甲烷转化率和合成气选择性。用Ｈ２ＴＰＲ，Ｈ２ＴＰＤ，ＳＥＭ和ＸＲＤ等手段和技术对催化剂进行了表征。ＣｅＯ２与Ｐｔ之间存在较强的相互作用（ＳＭＳＩ），这种作用促进了Ｐｔ在催化剂表面的分散，抑制了Ｐｔ在催化剂表面的迁移，大大降低了催化剂在反应中的完全燃烧活性，提高了催化剂的部分氧化活性和选择性，避免了因催化剂床层局部温度过高而导致催化剂活性下降或失活，提高了催化剂的稳定性。同时，在反应过程中，ＣｅＯ２通过促进水蒸气变换反应（ＷＧＳＲ）的进行使反应体系迅速达到平衡，提高了催化剂对Ｈ２的选择性。     

SO_2－4／TiO_2┐Al_2O_3－SnO_2催化剂的研制及其催化合成己二酸二辛酯

ＳＯ２－４／ＴｉＯ２┐Ａｌ２Ｏ３┐ＳｎＯ２催化剂的研制及其催化合成己二酸二辛酯高根之（曲阜师范大学化学系，曲阜２７３１６５）于世涛杨锦宗＊（大连理工大学精细化工系，大连１１６０１２）关键词固体超强酸，ＳＯ２－４／ＴｉＯ２－Ａｌ２Ｏ３－ＳｎＯ２催化剂，...     

乙醇水蒸气重整制氢催化剂Ni/Al2O3的研究

采用壳多糖螯合、浸渍法制备出Ni/Al2O3催化剂,并用BET、XRD、TG等方法对催化剂的性能、结构进行表征.通过在常压固定床流动体系中进行乙醇水蒸气重整制氢反应,讨论和评价了催化剂的性能.结果表明,10%Ni/Al2O3催化剂对乙醇水蒸气重整制氢表现出较好的活性.在反应温度高于500℃、水醇比为3∶1时,乙醇转化率100%,H2选择性在68%以上,增大水醇比可使H2选择性适度提高.     

微波辐射I2／Al2O3催化合成腈类化合物

微波辐射下,I2/Al2O3催化芳香醛和盐酸羟氨的无溶剂反应.一锅法合成了腈类化合物,产率80%～99%.     

Au/Mn2O3/Al2O3催化剂的制备及其deNOx活性

由于燃煤烟气、汽车尾气的过度排放 ,大气中ＮＯｘ(其中ＮＯ占 90 %以上 )浓度已呈上升趋势。ＮＯ在阳光作用下 ,易形成光化学烟雾 ,危害人体的呼吸系统。ＮＯ还是破坏大气臭氧层和形成酸雨的前驱气体之一 ,破坏生态环境。催化分解和催化还原法是消除ＮＯ(ｄｅＮＯｘ)的主要方法。但由于实际环境中ＮＯ往往与某一种或几种还原性气体 (如ＣＯ、低碳烃 )共存 ,所以催化还原法是人们公认的有应用前景的ｄｅＮＯｘ 方法[1 ] 。近十几年来 ,国内外研究较多的ｄｅＮＯｘ 催化剂是Ｃｕ ＺＳＭ 5 ,其催化活性除受原料气中氧含量的影响外 ,很大程度上…     

Pd-CeO2/Al2O3结构对其催化加氢脱硫反应性能的影响

分步浸渍法制备了不同Pd含量的Pd-CeO2/Al2O3催化剂,以噻吩加氢脱硫为探针反应,考察了Pd-CeO2/Al2O3催化剂的加氢脱硫性能,并应用XRD、H2-TPR、NH3-TPD、H2吸附和CO吸附等手段对催化剂结构进行了表征.结果表明,Pd在制备过程巾优先沉积在CeO2表面,Pd-Ce结合作用导致了界面效应和新的酸性位产生,Pd-Ce之间的界面效应是Pd-CeO2/Al2O3催化剂加氢脱硫活性提高的原因.2%Pd的Pd-CeO2/Al2O3催化剂拥有最高的单位质量Pd上的界面酸量,改性效果最为明显.Pd颗粒的优势面是Pd(111)面,这导致了强的Pd-Ce结合作用和界面效应,而1%和4%Pd的Pd-CeO2/Al2O3催化剂由于Pd-ce结合的空间结构使界面效应削弱,活性提高不明显.     

KF/Al2O3催化下取代水杨醛与达米酮的反应

取代水杨醛与5,5-二甲基-1,3-环己二酮(达米酮)在KF/Al2O3催化下反应生成一系列苯并吡喃的衍生物.产物的结构通过红外光谱、核磁共振氢谱和元素分析进行表征,并通过X单晶衍射分析进一步证实产物的结构.     

Nox Reduction Characteristics for Different Composition Ratios of Pt/Al2O3, Rh/Al2O3 Catalyst Mixtures Using Model Gas as Reformates

This study investigated the selective catalytic reduction (SCR) of nitrogen oxides (NO_x) with hydrocarbon in the presence of excess oxygen using various composition ratios of Pt/Al₂O₃, Rh/Al₂O₃ catalyst mixtures. The composition ratios were 1:1, 1:2, 2:1, 1:3 and 3:1 of 1 wt% Pt/Al₂O₃ and Rh/Al₂O₃, which are known to exhibit efficient NO_x reduction at low and high temperatures among the noble metal catalysts. Experiments conducted on a single reductant revealed that more efficient NO_x conversion could be obtained when Pt/Al₂O₃ and Rh/Al₂O₃ were mixed at a ratio of 3:1, rather than 1:1 or 1:3. In a single reductant condition, C₃H₆ 800 ppm (2400 ppmC₁) and 400 ppm (1200 ppmC₁) exhibited 50% and 38% NO_x conversion efficiency at 200°C, respectively. However, NO_x conversion efficiency gradually decreased when temperatures were increased above 250°C. With regard to Pt/Al₂O₃ and Rh/Al₂O₃ ratio, higher ratios of Rh/Al₂O₃ activated this Pt+Rh/Al₂O₃ catalyst in the high temperature range.     

Pt/Al2O3和Pt/CeO2/Al2O3催化甲烷部分氧化制合成气反应

研究了Pt/Al₂O₃和Pt/CeO₂/Al₂O₃对甲烷部分氧化制合成气反应的催化活性,发现Pt/CeO₂/Al₂O₃显示了更高的甲烷转化率和合成气选择性.用H₂-TPR、H₂-TPD、SEM-EDX和XRD等技术对催化剂进行了表征.CeO₂和Pt相互作用促进Pt在催化剂表面的分散,抑制Pt在催化剂表面的迁移;降低了催化剂的燃烧活性,提高了催化剂的部分氧化活性和选择性,可避免因催化剂床层局部温度过高而导致催化剂活性下降或失活,提高了催化剂的稳定性.同时,CeO₂通过促进水汽变换反应使反应体系迅速达到平衡,提高了催化剂对H₂的选择性.     

Comparative Study of CuO Species on CuO/Al2O3, CuO/CeO-Al2O3 andCuO/La2O-Al2O3 Catalysts for CO Oxidation

CuO/Al2O3, CuO/CeO2-Al2O3, and CuO/La2O3-Al2O3 (denoted as Cu/Al, Cu/CeAl, and Cu/LaAl) catalysts were prepared by an impregnation method. CuO species and CuO/Al2O3 thermal solid-solid interaction were characterized by in situ XRD, Raman spectroscopy and H2-TPR techniques. For the Cu/Al catalyst, a CuAl2O4 phase exists between the CuO and Al2O3 layer and the CuO phase exists on the surface in both highly dispersed and bulk forms. For the Cu/CeAl catalyst, there is highly dispersed and bulk CuO on the surface, but most of the CuO has transferred into the internal layer of CeO2 as bulk CuO and CuAl2O4. For the Cu/LaAl catalyst, only bulk CuO is present on the surface of the catalyst and no CuAl2O4 is formed. The catalytic activity order for CO oxidation is Cu/CeAl>Cu/Al>Cu/LaAl. The highly dispersed CuO on the catalyst surface may be the active phase for CO oxidation. The results show that the addition of CeO2 not only promotes both the transference of CuO and the formation of CuAl2O4 but also favors the CO oxidation due to the association of highly dispersed CuO with CeO2, while La2O3 hinders the transference of CuO and the formation of CuAl2O4.