Viscoelastic characterization of TEOS sols in three different solvents when DBTL is used as polycondensation catalyst

The gelation process of TEOS sols in three different solvents using di-n-butyltin dilaurate (DBTL) as polycondensation catalyst has been investigated. Sol compositions were similar to those employed in the field of stone consolidation for the conservation of historical buildings. Three different systems were studied: TEOS in ethanol (S-EtOH) which was tested to explain gelation in protic solvents; TEOS in a mixture of methylethylketone/acetone (S-MA) to represent aprotic solvents; and TEOS in a blend of MEK/ethanol (S-ME) for comparison of a system with properties intermediate between protic and aprotic solvents. The gelation process was studied by measuring the viscoelastic behavior near the gelation point (GP). A scaling exponent (Δ) was determined for the elastic modulus, G(ω)′ and the viscous modulus, G′′(ω), which both follow the same power law, ω^Δ, at GP. The fractal dimension, df, was calculated from the scaling exponent, Δ, for each TEOS-DBTL system. For each type of solvent studied, values of Δ from 0.34 to 0.53 with df of 1.9–2.2 were obtained. The results suggest that DBTL leads to a TEOS polycondensation mechanism similar to that observed for a base-catalyst system. However, the change in df suggests that there is a significant effect of the solvent on aggregation mechanisms of the gelation process. A diffusion limited cluster–cluster aggregation mechanism (DLCCA) was observed when ethanol was used as protic solvent, while a reaction limited cluster–cluster aggregation mechanism (RLCCA) was observed for MEK/acetone (aprotic solvent).     

Solvent effects on structural properties of SiO2 gel using n-octylamine as a catalyst

We have investigated the effect of solvent(ethanol, acetone, isopropanol) on the sol–gel process of tetraethylorthosilicate (TEOS) in which case, n-octylamine is used as polycondensation catalyst. Two sets of materials were prepared in the laboratory by using ethanol, acetone and isopropanol as solvents respectively: (1) xerogels from TEOS/n-octylamine, and (2) composites from TEOS/polyhedral oligomeric silsesquioxanes /n-octylamine. The chemical structure of xerogels was studied by FTIR, TG–DSC, scanning electronic microscope and nitrogen adsorption–desorption isotherms techniques. The results have shown that the solvents directly influence the gel time. Gel time is longer for acetone than that of ethanol and isopropanol. In the case of TEOS xerogels, the materials are essentially mesoporous when n-octylamine is used as a catalyst. Silica, when ethanol is used as a solvent, exhibits a more narrow pore size showing textures with a microstructure uniformly distributed with different porosity levels. However, when the aged-isopropanol gel is used, silica shows textures with a microstructure nonuniformly distributed.     

Internal Polarity of Class I and Class II Type Sol–Gel Hybrid Materials Using Aromatic Aminoketones as Solvatochromic Probes for Adsorbed Solvents and the Silicatic Cage

2-Hydroxyethylamino functionalized aromatic amino ketones bearing furyl and thienyl as well as 4-N, N-dimethylaminophenyl moieties have been used as solvatochromic probes when entrapped physically (Class I) and chemically bonded (Class II), respectively, to silicatic sol–gel hybrid materials. Class I hybrid materials have been obtained by encapsulation the dissolved probe during the acidically induced sol–gel procedure using various amounts of methyltrimethoxysilane and tetramethoxysilane as components. Class II xerogels have been synthesized by functionalization of the 2-hydroxyethylamino substituted aryl ketones with 3-isocyanatopropyltriethoxysilane and subsequent sol–gel process with TEOS (tetraethoxysilane). Molecular structures of the hybrid materials have been confirmed by solid-state MAS CP -²⁹Si and -¹³C NMR spectroscopy.Significant influences of the polarity of adsorbed solvents and of composition of the sol–gel material on the UV/Vis absorption spectrum of the encapsulated solvatochromic moiety are observed.Mobility of the entrapped probe and the associated influence of the adsorbed solvent upon the probe in the pores are significantly different for the two different classes of sol–gel materials studied.Solvatochromism of Class I xerogels shows that opposite effects of primary alcohols as function of alkyl chain length on the interfacial polarity are observed. They are caused by the influence of the internal surface modified with the solvent and origin solvent polarity on the UV/Vis spectrum of the encapsulated probe. Class II xerogels show related effects as observed for the probes studied in well behaved regular solvents.     

Synthesis and characterization of silica xerogels obtained via fast sol–gel process

The synthesis and physical properties of high surface area silica xerogels obtained by a two-step sol–gel process in the absence of supercritical conditions are reported. The hydrolysis and condensation reactions were followed by infrared spectroscopy. The increment in the bands corresponding to silanol and hydroxyl groups suggests that the hydrolysis reaction was complete during the first 30 min. The effect on surface area and global reaction time under various reaction conditions, such as type of alkaline catalyst and solvents, water–monomer and solvent–monomer molar ratios, was also studied. The obtained results suggest that surface area was increased using 3-aminopropyltriethoxysilane as catalyst. The use of isopropyl alcohol as solvent promotes the reduction of the capillary stress, giving a well-structured xerogel. As a conclusion, with H₂O/i-PrOH/TEOS in a molar ratio of 10:4:1, it was possible to obtain silica xerogels with surface areas about 1,240 m²/g. Such surface areas are comparable with those obtained under supercritical conditions (aerogels), and higher than those xerogels conventionally obtained under normal condition (500–800 m²/g).     

Colloidal crystallization of colloidal silica modified with ferrocenyl group-contained polymers in organic solvents

Surface modification of colloidal silica with ferrocenyl-grafted polymer and colloidal crystallization of the particles in organic solvent were studied. Poly(methyl methacrylate-co-vinylferrocene)-grafted silica never formed colloidal crystals in polar solvent, such as acetone, acetonitrile, ethanol and N,N-dimethylformamide (DMF), while poly(methyl methacrylate-co-ferrocenyl acrylate)-grafted silica gave colloidal crystallization in DMF. The particles prepared by grafting of poly(N,N-dimethylacrylamide-co-vinylferrocene), with vinylferrocene (Vfc) mole fraction of 1/13 and 1/23, were observed to give the crystallization in ethanol and DMF over particle volume fraction of 0.058. Further, silica modified with copolymer of Vfc and N-vinyl-2-pyrrolidone, N-vinylcarbazole or N-isopropylacrylamide formed colloidal crystals in ethanol and DMF. Especially, poly(N-isopropylacrylamide-co-Vfc)-grafted silica, which was composed of the highest mole fraction of vinylferrocene, 1/3, afforded colloidal crystallization in ethanol over particle volume fraction of 0.053. Relatively high polar vinylferrocene copolymer grafting of silica resulted in colloidal polymerization in organic solvents.     

TEOS–colloidal silica–PDMS‐OH hybrid formulation used for stone consolidation

The consolidation of materials concept, which consists of introducing a chemical substance (consolidant) into degraded stone, has been applied to architectural conservation. Silicon compounds such as tetraethoxysilane (TEOS) are frequently used as a base for commercial consolidant formulations due to their ability to form a siloxane polymer such as SiO₂. However, the silica xerogels deposited into the stone show poor performance and the gels obtained are non‐porous and tend to crack during the drying stage. In order to avoid the fractures and to improve gel properties, we propose the synthesis of a hybrid consolidant based on TEOS and fillers such as colloidal silica (200 nm in diameter) and hydroxy‐terminated polydimethylsiloxane (PDMS‐OH). Both additives enhance gel properties such as porosity and elasticity, leading to the formation of non‐fractured and permeable gels. Characterization of the hybrid xerogel was carried out by nitrogen adsorption and ²⁹Si MAS‐NMR. The properties of the hybrid xerogels were compared with those prepared from a formulation based on TEOS (T‐ME) with a composition similar to a commercial product. In order to evaluate the effectiveness of the hybrid consolidant, it was applied to tuff‐stone of historical monuments in the city of Guanajuato, Mexico. The tuff‐stone was also treated with the formulation T‐ME. Both treatments were studied by determining the percentage of consolidant deposited, evaluating changes in porosity and hardness of the treated stone. The applicability of the hybrid consolidant for the decayed tuff‐stone is under study. Copyright © 2010 John Wiley & Sons, Ltd.     

Influence of Sol-Gel Synthesis Parameters on the Microstructure of Particulate Silica Xerogels

The influence of key sol-gel synthesis parameters on the pore structure of microporous silica xerogels was investigated. The silica xerogels were prepared using an acid-catalyzed aqueous sol-gel process, with tetraethoxysilane (TEOS) as the silicon-containing precursor. At high H2O : TEOS ratios, sols synthesized at pH 2–3 yielded minimum values of mean micropore diameter and micropore volume. Analysis of the resulting Type I nitrogen adsorption isotherms and the equilibrium adsorption of N(C4F9)3 indicated micropore diameters for these xerogels of less than approximately 10 Å.Xerogel micropore volumes corresponding to sols prepared at pH 3 and an H2O : TEOS ratio of r = 83 were consistent with nearly close packing of silica spheres in the xerogel. Xerogel microstructure was only weakly dependent upon H2O : TEOS ratio during sol synthesis for r > 10. Xerogel micropore volume increased rapidly with sol aging time during an initial induction period of particle formation. However, the xerogel microstructure changed only slowly with time after this initial period, suggesting potential processing advantages for the particulate sol-gel route to porous silica materials.Surface adsorption properties of the silica xerogels were investigated at ambient temperature using N2, SF6, and CO2. CO2 adsorbed most strongly, SF6 also showed measurable adsorption, and N2 adsorption was nearly zero. These results were consistent with the surface transport of CO2, and to a lesser extent SF6, observed in gas permeation studies performed through thin membrane films cast from similarly prepared silica sols.     

Formation of colloid crystals from polymer-modified monodisperse colloidal silica in organic solvents

The formation of colloid crystals from monodisperse and polymer-modified silica particles in organic solvents was investigated. Maleic anhydride–styrene copolymer-modified silica formed crystals in polar organic solvents, which dissolve the copolymer, while the original colloidal silica formed crystals in organic solvents which were miscible with water. The critical volume fraction in the crystal formation of the polymer-modified silica was lower than that from the unmodified silica in the same solvent. Polystyrene- and poly(methyl methacrylate)-modified silica particles also crystallized in organic solvents, but the features of the formation were different from those of poly(maleic anhydride-styrene)-modified particles. Received: 19 September 1998 Accepted in revised form: 1 January 1999     

Hydrophobic and Physical Properties of the Two Step Processed Ambient Pressure Dried Silica Aerogels with Various Exchanging Solvents

The experimental results by using various exchanging solvents in the preparation of two step (acid and base) processed ambient pressure dried hydrophobic silica aerogels, are reported. Silica alcogels were prepared by hydrolysis with oxalic acid and condensation with NH₄OH of ethanol diluted tetraethylorthosilicate (TEOS) precursor and hexamethyldisilazane(HMDZ) methylating agent. The exchanging solvents used were: hexane, cyclohexane, heptane, benzene, toluene and xylene. The physical properties such as % of volume shrinkage, density, pore volume, % of porosity, thermal conductivity, % of optical transmission, surface area, pore size distribution and contact angle (θ) of the silica aerogels with water, were measured as a function of EtOH/TEOS molar ratios (R) for all the exchanging solvents. It was found that the physical and hydrophobic properties of the silica aerogels strongly depend on the nature of the solvent and R. Heptane solvent resulted in highly transparent (≈90% optical transmission at 700 nm for 1 cm thick sample), low density (≈0.060 g/cm³), low thermal conductive (≈0.070 W/m·K), high % of porosity (97%), high surface area (750 m²/g), uniform porosity and hydrophobic (θ ≈ 160°) aerogels compared to other solvents. On the otherhand, xylene resulted in aerogels with higher hydrophobicity (θ ≈ 172°) among other solvents.     

Preparation of transparent,monolithic silica xerogels with low density

A new process to make monolithic and transparent silica xerogels with similar properties as silica aerogels by drying at ambient pressure has been studied. The xerogels are produced by strengthening the gel structure by additional precipitation of silica after the initial gelation. The additional precipitation of silica is achieved by ageing the alcogels in solutions of tetraethoxysilane (TEOS) and the aging is followed by a relatively rapid drying (<48 h) at ambient pressure. Due to the increased strength of the alcogels it is shown that the shrinkage during drying can be reduced and hence low density xerogels are obtained even if new monomers are added.     

纳米二氧化硅的表面改性研究

以γ-缩水甘油醚丙基三甲氧基硅烷(GPTMS)对酸催化水解正硅酸乙酯(TEOS)聚合得到的纳米二氧化硅胶粒表面进行接枝改性,用激光粒径仪测定二氧化硅颗粒的粒径,并用透射电子显微镜(TEM)观察了改性前后二氧化硅胶粒的分散状况,采用傅立叶红外(FTIR)光谱法对改性前后的二氧化硅粉体进行了分析,通过热失重分析(TGA)法对GPTMS接枝改性二氧化硅胶粒表面的接枝度进行分析计算,同时对颗粒溶胶的ζ电位进行了测试,结果表明:改性后二氧化硅胶粒分散性大大提高,硅烷偶联剂浓度对接枝度有显著影响,当GPTMS的浓度为1mL/S iO2(g)时,接枝度达到最大,且颗粒表面的物理化学性能发生显著变化。     

Characterisation of hybrid xerogels synthesised in acid media using methyltriethoxysilane (MTEOS) and tetraethoxysilane (TEOS) as precursors

The mild synthetic conditions provided by the sol-gel process and the versatility of the colloidal state allow for the mixing of inorganic and organic components at the nanometre scale in virtually any ratio for the preparation of hybrid materials. Our interest in hybrid xerogels focuses on combining their porosity with other properties to prepare optic-fibre sensors. The specific aim of this paper is to synthesise hybrid xerogels in acid media using methyltriethoxysilane (MTEOS) and tetraethoxysilane (TEOS) as silica precursors and to investigate the effect of the MTEOS molar ratio on the structure and porous texture of xerogels. Gelation time exponentially increased as the MTEOS molar ratio increased. Increasing the MTEOS molar ratio yielded xerogels with lower density and lower particle size. The incorporation of MTEOS resulted in new FTIR bands at 1276 and 791 cm⁻¹, which was attributed to vibrational modes of methyl group. The band around 1092 cm⁻¹ associated with siloxane bonds shifted to lower wavenumbers and split into two bands. The ²⁹Si spectra only showed the Q ⁿ (n=2, 3, 4) signal in xerogels with 0% MTEOS and the T ⁿ (n=2, 3) signal in xerogels with 100% MTEOS; hybrid xerogels showed both Q and T signals. From XRD peaks at 2θ around 9°, we inferred that xerogels (>70% MTEOS) consisted of nanocrystalline CH₃–SiO_3/2 species. Increasing the MTEOS molar ratio produced xerogels with lower pore volumes and lower average pore size. The integration of methyl groups on the surface decreased the surface polarity and, in turn, the characteristic energy.     

Synthesis of monodisperse fluorescent core-shell silica particles using a modified Stober method for imaging individual particles in dense colloidal suspensions

Core-shell silica particles, with a diameter of 1.5 mum, containing a dye fluorescein isothiocyanate (FITC), are synthesized by the hydrolysis and condensation of tetraethylorthosilicate (TEOS). Sodium dodecyl sulfate (SDS) is added to synthesize fluorescent core particles with the diameter of approximately 1 mum. In the addition of SDS, the surface charge reduced by counterions (Na+) of the surfactant leads to a higher degree of aggregation of the primary particles and the formation of larger secondary particles. The particle growth kinetics confirms the aggregation growth model for the synthesis of monodisperse silica particles, and also shows the dependence of final particle size on colloidal stability resulting from the addition of SDS. Light and X-ray scattering data reveal that the final particles have compactly packed structures with smooth surfaces. The seeded growth technique is then used to form a silica shell layer on the fluorescent core. The added amount of water and NH4OH has significant effects on shell formation. Finally, the final core-shell silica particles are modified by chemisorption of octadecanol at the surface to be dispersed in organic solvents. Octadecyl-coated silica particles are sterically stabilized in silica index-matching solvents such as chloroform and hexadecane to directly image separate particles using confocal microscopy. In chloroform, the organophilic silica particles disperse well, whereas in hexadecane they form a volume-filling gel structure at room temperature.     

Synthesis of polysiloxane xerogels with fluorine-containing groups in the surface layer and their sorption properties

Hydrolysis and polycondensation reactions of tetraethoxysilane (TEOS) with 3,3,3-trifluoropropyl-trimethoxysilane (TFMS) or 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFES) were used to synthesize xerogels functionalized with fluorine-containing groups. According to transmission electron microscopy, the skeletons of synthesized polysiloxane xerogels have globular structures and consist of agglomerates of particles with fluorinated groups on their surfaces. FTIR spectroscopy showed that primary xerogel particles possess spatial polysiloxane networks, with fluorinated groups along with silanol groups and water in the surface layer. According to thermal analyses, the water content was 3–8 wt.%, and it decreased with increasing length of the fluorinated chain. Thermal destruction of the surface layer starts above 300 °C. The sorbents that were obtained were predominantly mesoporous materials with well-developed porous structures (S_BET = 400–960 m² g⁻¹, V_s = 0.66–0.93 cm³ g⁻¹). The influence of the TEOS/functional silane ratio and the natures of the functional groups on the structural and adsorptive properties were shown. The samples synthesized are organophilic. The affinity for n-hexane increases with increasing length of the fluorine-containing chain (PFES) and the content of fluorinated groups in the surface layer. The hybrid organic–inorganic materials that were obtained can be used for adsorption of hydrocarbons, including oil, from water.     

Transparent inorganic/organic copolymers by the Sol-Gel process: Copolymers of tetraethyl orthosilicate (TEOS), vinyl triethoxysilane (VTES) and (meth)acrylate monomers

Vinyl triethoxysilane (VTES) and (meth)acrylate monomers were mixed to create covalently bonded inorganic/organic copolymers, with and without tetraethyl orthosilicate (TEOS). Vinyl groups underwent free radical polymerization along with copolymerization with (meth)acryl groups of the monomer. For the two-monomer system, (meth)acrylate monomer and VTES, polymerization resulted in mechanically strong copolymers with flexure strengths greater than 40 MPa. Three-component materials obtained by polymerization of (meth)acrylate monomer, VTES and TEOS were homogeneous, highly transparent, with flexure strengths similar to those for silica xerogels, about 20 Mpa.     

Seed polymerization of tetraethyl ortho-silicate in the presence of rod-like colloidal particles of anionic palygorskite and cationic β-FeO(OH)

Kinetic analyses were made of the seed polymerization of tetraethyl ortho-silicate (TEOS) in the presence of rod-like colloidal particles of palygorskite and cationic -FeO(OH) by turbidity and dynamic light-scattering measurements. Transmission electron microscopic measurements supported the formation of core-shell particles. The seed polymerization of TEOS took place exclusively on the surfaces of palygorskite. The main cause of the observation is due to the fact that the main component of palygorskite is SiO₂ and the affinity between palygorskite and TEOS is high, though the electrostatic repulsion between them is not favorable for shell formation. The shell formation of silica on a -FeO(OH) particle also proceeded. The electrostatic attraction forces between the anionic polar TEOS monomers and cationic -FeO(OH) particles played an important role in shell formation. These results are consistent with a polymerization mechanism consisting of the formation of small preliminary particles followed by their coalescence on the surfaces of the seeds to give the final large particles coated with silica layers.     

An investigation on structure and texture of silica-magnesia xerogels

Silica-magnesia xerogels were prepared by reacting tetraethoxysilane (TEOS) and magnesium chloride (MgCl₂) under acidic conditions. The TEOS/MgCl₂ molar ratio was varied from 1:0 to 0:1. The xerogels were characterized by a set of complementary techniques, namely, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), nitrogen adsorption, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Magnesium contents of silica-magnesia xerogels were between 1.3 and 16.0 wt%. Increasing TEOS/MgCl₂ molar ratio affords higher homogeneity and crystallinity. The presence of low Mg content (<5%) increases specific surface area compared to bare silica. A cubic grain morphology was observed for xerogels with higher Mg content.     

Development of various PS-b-P4VP micellar morphologies: fabrication of inorganic nanostructures from micellar templates

A liquid-phase method for preparing uniform-sized silica nanospheres (SNSs) 12 nm in size and their three-dimensionally ordered arrangement upon solvent evaporation have recently been pioneered by us. Here we report the successful control of the sphere sizes in the wide range from 14 to 550 nm by the seed regrowth method. In this method, the dispersion of SNSs 14 nm in size as seeds was prepared in the emulsion system containing Si(OEt)(4) (TEOS), water and arginine under weakly basic conditions (pH 9-10). An appropriate portion of this dispersion is added to the solution containing water, ethanol and arginine, and then TEOS is added. The additional TEOS introduced into the regrowth system contributed only to the resumed growth of the seeds, not to the formation of new silica particles. The size of interparticle pores was finely tuned by changing the size of the spheres. The preparation of three-dimensionally ordered porous carbons by using the colloidal array of silica nanospheres as a template is also reported.     

Sodium hydride-initiated polymerizations of vinyl monomers in aprotic solvents

Polymerizations of several vinyl monomers at 25°C in aprotic solvents (dimethyl sulfoxide, N,N-dimethylacetamide, and hexamethylphosphoric triamide) using sodium hydride dispersion as initiator yield low to intermediate molecular weight polymers. The molecular weight of the resulting polymer as well as the mode of initiation depends on the monomer and aprotic solvent used. Initiation of polymerization of monomers with available α hydrogens (methyl acrylate, acrylonitrile) involves monomer anion, while initiation of a monomer with no α hydrogen (methyl methacrylate) proceeds by a more complex mechanism. In contrast, initiation of styrene and α-methylstyrene proceeds by dimsyl anion addition to monomer in dimethylsulfoxide. Although the triad tacticities and number-average molecular weights of poly(methyl methacrylate) samples obtained from all three aprotic solvents are nearly the same, poly(methyl methacrylates) prepared in dimethyl sulfoxide and N,N-dimethylacetamide give polymers having polydispersities of ～3, while a very polydisperse polymer is obtained in hexamethylphosphoric triamide.     

单分散二氧化硅球形颗粒的制备与形成机理

在醇水混合溶剂中以氨作催化剂，正硅酸乙酯为硅源，通过溶胶—凝胶工艺制 备单分散二氧化硅球形颗粒，通过透视电镜进行研究各种反应条件如溶剂类型、氨 和水的浓度、水解温度等对二氧化硅的颗粒大小和形貌的影响．结果显示：以甲醇 和乙醇为溶剂可以形成单分散的二氧化硅球形颗粒，以丙醇和丁醇为溶剂，二氧化 硅球形颗粒容易聚集；在其它条件不变的情况下，球形颗粒的粒径随水和硅源的浓 度增加而增大；而且水解温度的升高，生成的颗粒粒径也逐渐增大，仔细研究和讨 论了二氧化硅颗粒在不同反应条件下的形成机理．