超静定梁?柱的解析解研究

本文采用渐进积分法研究了超静定梁?柱的弯曲问题. 首先建立超静定梁?柱的四阶挠度微分方程, 考虑到边界条件和连续光滑条件, 采用连续分段独立一体化积分法求解得到了挠度的精确解析解. 为了满足工程设计需要, 构造了超静定梁?柱的四阶挠度微分迭代方程, 选取无轴向力作用时超静定梁的挠曲线作为梁的初函数, 将初函数代入梁的四阶挠度微分迭代方程进行积分, 利用边界条件和连续光滑条件确定积分常数, 得到下一次迭代挠度函数, 依次进行迭代积分运算. 计算出了最大挠度、最大转角和最大弯矩等用轴向力放大系数表示的多项式解析函数解. 本文选取了两种边界条件下受分布力作用的超静定梁?柱进行分析, 计算结果表明, 当超静定梁?柱所受的轴向力小于欧拉临界力的1/2时, 迭代六次误差就可以控制在1%以内; 不仅梁?柱最大位移和最大内力的大小随轴向力的增大而增大, 而且其位置也随轴向力的增大而发生迁移. 本文的研究对揭示轴向力对超静定梁?柱变形和内力的影响有重要意义, 为超静定梁?柱的实际设计提供了一定的理论基础.      

箱形梁剪力滞效应分析中的翘曲位移函数及广义内力研究

以薄壁箱梁的弯曲计算理论为基础,从分析翼缘板的面内剪切变形和弯曲剪力流的分布规律入手,从理论上证明二次抛物线是箱形梁剪力滞效应分析中的合理翘曲位移函数。选取剪力滞效应引起的附加挠度作为广义位移,用基于最小势能原理的能量变分法建立箱形梁剪力滞效应分析的控制微分方程和边界条件。对箱梁横截面上新出现的广义内力给出严密定义,并建立了剪力滞翘曲应力的简便计算公式,它与初等梁弯曲应力公式具有相同的形式。对一个简支箱梁模型的计算表明,计算值与实测值吻合良好,从而证实了本文的分析方法和建立的公式是正确的。不同于弯矩的分布,剪力滞广义力矩具有快速衰减的分布特征。对集中荷载作用下的简支箱梁算例,剪力滞效应使其跨中挠度增大达12%,工程实践中必须认真对待。     

Large deflections of cantilever beams of non-linear elastic material under a combined loading

Large deflection of cantilever beams made of Ludwick type material subjected to a combined loading consisting of a uniformly distributed load and one vertical concentrated load at the free end was investigated. Governing equation was derived by using the shearing force formulation instead of the bending moment formulation because in the case of large deflected member, the shearing force formulation possesses some computational advantages over the bending moment formulation. Since the problem involves both geometrical and material non-linearities, the governing equation is complicated non-linear differential equation, which would in general require numerical solutions to determine the large deflection for a given loading. Numerical solution was obtained by using Butcher's fifth order Runge-Kutta method and are presented in a tabulated form.     

具有内核伸出段的套管构件在线接触阶段的受力性能研究

针对具有内核伸出段的轴压套管构件,建立了线接触阶段的力学模型;利用小挠度理论推导出了内核和套筒的剪力、弯矩、挠度、分布接触力、集中接触力等物理量的计算公式。通过与无内核伸出段套管构件的对比算例验证了本文相关物理量推导的正确性,分析了内核与套管在不同刚度比下相关物理量的变化情况。结果表明:由于内核伸出段的影响,点接触会提前向线接触变化,使套管构件的轴向承载力显著下降,端部的接触反力及内核的剪力、弯矩有显著的增加。对具有内核伸出段的套管构件进行了力学性能分析,结果表明:内核与套筒的间隙对线接触长度没有影响,内核的弯矩、剪力随着间隙的增加而增大;随着内核伸出段长度的增加,线接触长度及内核的弯矩、剪力增大。     

Transverse-longitudinal bending of rheonomic rods

In [1, 2], an energy method for the determination of critical buckling times is developed for rods subjected to compression in the conditions of longitudinal bending. In this case, for given compressive loads, the bending moments in the rod cross-sections depend only on the current deflection of the rod axis. In contrast to longitudinal bending, in the case of transverse-longitudinal bending the bending moment in general depends not only on the deflection but also on the axial coordinate and the reaction forces in the supports. Depending on the rod fixing conditions, the problems of transverse-longitudinal bending can be categorized as statically determinate or statically indeterminate. In the latter case, the derivation of equilibrium conditions for a rod segment is complicated by the indefiniteness of the reactions in the rod buckling process. In the current paper, the energy method developed in [1, 2] is extended to a class of statically indeterminate transverse-longitudinal bending problems. To determine the redundant variables, it is proposed to use the principle of minimum of additional dissipation.     

Parametrically Excited Vibration of a Timoshenko Beam on Random Viscoelastic Foundation jected to a Harmonic Moving Load

The vibration response of a Timoshenko beam supported by a viscoelastic foundation with randomly distributed parameters along the beam length and jected to a harmonic moving load, is studied. By means of the first-order two-dimensional regular perturbation method and employing appropriate Green's functions, the dynamic response of the beam consisting of the mean and variance of the deflection and of the bending moment are obtained analytically in integral forms. Results of a field measurement for a test track are utilized to model the uncertainty of the foundation parameters. A frequency analysis is carried out and the effect of the load speed on the response is studied. It is found that the covariance functions of the stiffness and the loss factor both have the shape of an exponential function multiplied by a cosine function. Furthermore, it is shown that in each frequency response there is a peak value for the frequency, which changes inversely with the load speed. It is also found that the peak value of the mean and also standard deviation of the deflection and bending moment can be a decreasing or increasing function of the load speed depending on its frequency. An erratum to this article is available at .     

Failure criterion for reinforced concrete beams and plates subjected to membrane force,bending and shear

In this paper, a failure criterion for reinforced concrete plates is derived through the kinematic method in the framework of the limit analysis theory. This criterion is expressed in terms of the stress resultant variables: membrane force, shear force and bending moment at once. The aim of the authors is to be able to predict the failure of reinforced concrete plate structures in statics or in slow dynamics using directly the internal forces (membrane and shear forces and moment) resulting from a finite-element computation.In a first step, a beam criterion is derived. The closed form expression of the criterion shows that it is made up of two parts, one independent of the moment (i.e. depending only on the normal force and the shear force) and one depending on the normal force, the shear force and the bending moment. This structure of the criterion allows to determine two failure modes: shear failure and bending failure.Then in a second step, the beam criterion is extended to the case of reinforced concrete plates. The obtained criterion is partly numerical and partly a close form expression. It gives an upper bound of the load, and when this limit load is reached, the criterion is able to supply, on one hand, the failure mode (as seen in the beam case) and, on the other hand, the angles of the failure plane in the reinforced concrete plate section.Thirdly, the criterion is implemented in the finite element software Europlexus and validated with respect to punching experimental tests. We show that the criterion must be used with an effectiveness factor applied on the concrete compressive strength.     

中墩斜置对连续箱梁弯扭性能的影响

为了揭示中墩斜支承对连续箱梁力学性能的影响,本文考虑约束扭转和竖向挠曲耦合作用,建立了斜支承连续箱梁的力法方程,并获得了内力和变形的解析式.选取斜支承两跨连续箱梁为数值算例,分别计算了竖向对称和偏心均布荷载作用下的内力和变形,并用ANSYS软件计算了控制截面的弯矩.计算结果表明,本文方法计算的弯矩与ANSYS计算值吻合...     

考虑刚度折减的多棱锥型套接钢管杆挠度及附加弯矩研究

多棱锥型钢管杆广泛应用于城市周边输电线路,管与管之间通常采用法兰连接,套接连接应用不大。鉴于目前对于多棱锥型套接钢管杆挠度的计算方法研究相对较少,本文根据梁的挠曲线微分方程理论,结合套接节点刚度折减,推导出在常见荷载(弯矩M、水平力P和均布力q)作用下多棱锥型套接钢管杆挠度和附加弯矩的计算方法。最后,选取典型套接钢管杆进行对比分析,得出了一些重要结论。本文对套接钢管杆挠度计算进行细致的研究,可作为输电线路钢管杆套接连接设计的参考     

???????????????????????????о?

提出该结构体系在水平载荷作用下,可视为夹层复合构件,并提出了计算模型. 根据 变形协调原理对其进行受力分析,建立了多层多跨密肋复合墙体结构横向位移及各组成构件承 受剪力和弯矩表达式. 通过计算分析指出,各组件剪力分配只与各组件刚度及宽度比有关, 内墙板上部分配剪力大于下部,边框反之;各组件局部弯矩系数随$\lambda $的增加而减小,其整体工作性能增强,当$\lambda $增加到一定数值时,其工作性能与悬壁构件类似.     

考虑畸变影响的箱梁横向弯矩计算方法

为研究偏心垂向荷载作用下梯形截面单室箱梁的横向弯矩,对框架分析法计算箱梁横向弯矩的方程进行优化,并在刚性支承法的基础上提出一种更加简单的横向弯矩计算方法;与框架分析法不同,横向弯矩可采用能量变分法求解,建立以箱梁顶板剪力差为未知量的四阶控制微分方程,采用比拟的弹性地基梁解法解出剪力差,得出梯形截面单室箱梁横向弯矩的能量变分法解。对几种箱梁横向弯矩计算方法用两个算例进行验证,结果表明,能量变分法解将箱梁底板上的弯矩误差绝对值由15.41%降到了9.68%;本文方法得出的横向弯矩结果和有限元结果吻合较好,弯矩误差绝对值最大不超过6.01%;本文方法和能量变分法可有效降低箱梁底板上的弯矩误差,计算精度得到提高。     

基于细长梁单元的悬索桥主缆线形分析Study on main cable shape of suspension bridge based on slender beam element

悬索桥主缆线形的精细化计算需要同时考虑弯曲刚度及初始弯曲的影响,为此将主缆离散为小挠度的细长梁单元,推导包含自重项的细长梁单元的刚度矩阵,其中考虑了轴力对弯曲刚度的影响及弯矩引起的轴向刚度修正系数。基于细长梁单元编制主缆线形计算的有限元程序,采用改进的迭代法求解几何非线性结构的平衡状态,并考虑鞍座处主缆线形的修正。利用程序计算了两座悬索桥主缆在恒载作用下的变形,结果表明,主缆弯曲刚度对跨中和桥塔附近主缆线形的影响较大,且矢跨比越大,主缆线形的计算误差就越大。由弯曲刚度引起的主缆线形计算误差将会带来吊索下料长度计算不准确、索夹放样坐标不准确、成桥桥面线形达不到设计线形以及成桥吊索力分布不均匀等问题,尤其是对矢跨比较大的自锚式悬索桥,需要在设计和施工中引起足够的重视。     

Novel load cell for measuring axial force,shear force,and bending movement in large-scale structural experiments

This paper describes the design, construction and testing of a load cell to measure the axial force, shear force, and bending moment at the end of a structural beam. The capacities of the load cell are 780 kN in axial load, 350 kN in shear, and 200 kNm in bending. These magnitudes, together with the requirement that the load cell should be kept as slim as possible, necessitated a novel design comprising three steel double-spring elements machined with semicircular channels to provide localized strain amplification. The load cell was designed with the aid of detailed finite element analysis and was machined from grade 55 steel. After strain gaging, it was subjected to an extensive series of calibration tests. Results from these tests are reported, together with those from some early experiments in which two load cells were used to measure the behavior of structural steel knee elements.     

考虑接缝传荷的文克勒地基上矩形薄板的级数解

应用双重正弦级数展开的方法,推演得到了文克勒地基上计入两块矩形板间接缝传荷效应的级数解。假设接缝传递剪力与板间挠度差成正比、传递弯矩与板间转角差成正比,进而分析了单轮和单轴荷载作用在纵缝边缘中部时,接缝传荷效应对板边最大挠度和最大应力的影响规律;通过引入接缝传荷效应系数和接缝极限传荷的两个挠度比及两个应力比,建立了计入接缝传荷效应的板边最大挠度和最大应力的一般式,总结了不同板尺寸、荷载面积尺寸和类型及板材料泊松比对四个接缝影响系数和四个接缝极限传荷的挠度比及应力比的影响规律。结果表明:不同荷载面积下,受荷板接缝边缘最大挠度、最大应力均随弯矩或剪力传荷刚度系数的增大而减小,且应力的变化幅度相较挠度要小。影响系数fV^w(ξV)、fM^w(ξM)、fM^σ(ξM)与荷载圆相对半径(a/l)、相对板长(L/l)和相对板宽(B/l)无关,且单轮荷载与双轮荷载规律相同;而影响系数fV^σ(ξV)与荷载圆相对半径(a/l)有关,与相对板长(L/l)和相对板宽(B/l)无关;挠度比λV^w与荷载圆相对半径、板尺寸(L/l,B/l)及泊松比v无关,恒等于0.5,而λM^w、λV^σ、λM^σ均与荷载相对半径(a/l)、板尺寸(L/l,B/l)及泊松比v有关,且影响因素中荷载面积尺寸的影响最为显著。     

面内变刚度薄板弯曲问题的挠度?弯矩耦合神经网络方法

发展了一种求解面内变刚度功能梯度薄板弯曲问题的神经网络方法. 面内变刚度薄板弯曲问题的偏微分控制方程为一复杂的4阶偏微分方程, 传统的基于强形式的神经网络解法在求解该偏微分方程时可能会遇到难以收敛、边界条件难以处理的情况. 本文基于Kirchhoff薄板弯曲理论, 提出了一种直角坐标系下任意面内变刚度薄板弯曲问题的神经网络解法. 神经网络模型包含挠度网络与弯矩网络, 分别用于预测薄板的挠度与弯矩, 从而将求解4阶偏微分方程转换为求解一系列二阶偏微分方程组, 通过对挠度、弯矩试函数的构造可使得神经网络计算结果严格满足边界条件. 在误差的反向传播中, 根据本文提出的误差函数公式计算训练误差并结合Adam优化算法更新模型的内部参数. 求解了不同边界条件、形状的面内变刚度薄板弯曲问题, 并将所得计算结果与理论解、有限元解进行对比. 研究表明, 本文模型对于求解面内变刚度薄板弯曲问题具备适应性, 虽然模型中的弯矩网络收敛较挠度网络要慢, 但本文方法在试函数的构造上更为简单、适应性更强.      

Shear and Bending Response of a Rigid-Plastic Beam to Partly Distributed Blast-Type Loading

ABSTRACT

A study is undertaken on dynamic response of a simply supported rigid perfectly plastic beam that is subjected to partly distributed blast-type pressure loading. The beam material has finite shear strength and obeys a square yield criterion relating bending moment and transverse shear force. The transverse dynamic load is uniformly and symmetrically distributed over a middle portion of the span. Various patterns of deformation, which combine plastic bending and shear sliding, are obtained for a wide range of parameters, and the effects of transverse shear forces and time dependence of the dynamic pressure are examined.     

用切比雪夫多项式研究短梁的弯曲计算

考虑剪切效应,利用切比雪夫多项式构造严格满足表面切应力边界条件的轴向位移表达式,建立了短梁弯曲问题的新理论．利用奇异函数把作用在短梁上的复杂外载荷表示为分布载荷,推导出了短梁弯曲时的截面正应力公式及挠曲线表达式．把采用切比雪夫多项式推导出短梁的弯曲计算公式计算结果与弹性理论计算结果进行比较,可知该方法的计算精度较高．研究结果表明：在复杂外载荷作用下,当长高比小于等于6时,剪切变形对梁的弯曲挠度影响较大,而当长高比小于3时,剪切变形对梁的弯曲应力影响较大;因此建议采用切比雪夫多项式方法给出的挠度表达式、弯曲应力进行计算,因为切比雪夫多项式方法不但给出了复杂外载荷作用下梁截面挠度、弯曲应力的计算通式,而且该方法具有计算过程简便、精度高的优点．     

Stochastic response of an axially loaded composite Timoshenko beam exhibiting bending–torsion coupling

A spectral finite element method is proposed to investigate the stochastic response of an axially loaded composite Timoshenko beam with solid or thin-walled closed section exhibiting bending–torsion materially coupling under the stochastic excitations with stationary and ergodic properties. The effects of axial force, shear deformation (SD) and rotary inertia (RI) as well as bending–torsion coupling are considered in the present study. First, the damped general governing differential equations of motion of an axially loaded composite Timoshenko beam are derived. Then, the spectral finite element formulation is developed in the frequency domain using the dynamic shape functions based on the exact solutions of the governing equations in undamped free vibration, which is used to compute the mean square displacement response of axially loaded composite Timoshenko beams. Finally, the proposed method is illustrated by its application to a specific example to investigate the effects of bending–torsion coupling, axial force, SD and RI on the stochastic response of the composite beam.     

混凝土框架结构内力测量传感器研制

研制了一种可用于混凝土结构试验中测量柱底截面轴向力、剪力和弯矩的内力测量传感器。该传感器主要由加载板、基座、4根竖向测力杆和2根水平测力杆组成。使用时,柱底截面的内力通过加载板传递给6根测力杆,根据6根测力杆的结果,通过力平衡方程可以计算实际加载的轴向力、剪力和弯矩的大小。对该传感器进行了4种工况下的标定试验。结果表明,传感器的测量误差满足框架结构内力测量精度要求。将该传感器应用到单层两跨的钢筋混凝土框架推覆试验中,获得了整个试验过程中构件的内力时程。     

复合材料结构力学分析CAE软件现状

复合材料结构分析软件是用以分析、设计复合材料结构的重要工具,常用的复合材料结构分析软件包括基于CAD软件发展而来的复合材料分析工具、通用有限元软件自带复合材料分析工具和以Digimat等为代表的专业化复合材料结构分析软件。本文对常用的复合材料分析软件进行了综述,介绍其主要功能,从学术、应用等多方面探讨相关产品的优点及不足;论述了专业化复合材料结构分析软件的特点及功能;分析了复合材料结构分析软件的现状和发展趋势;探讨了复合材料结构力学分析CAE软件在国产化方面所需进一步解决的问题。