Optical studies of dynamic director configurations in ferroelectric liquid crystal devices

An investigation into the transmission spectrum of a ferroelectric liquid crystal device is undertaken. This is done both for an initial static state and during a switching process. Comparisons are made between experimental data and theoretical predictions. The dynamic internal director configurations in the device is shown to be consistent with a simple model during both monopolar and bipolar addressing pulses.     

Electro-optical properties of photo-aligned photonic ferroelectric liquid crystal fibres

Electro-optical and spectral studies of isotropic photonic crystal fibre (PCF) infiltrated with photo-aligned ferroelectric liquid crystal (FLC) under influence of external electric field are described. Desired alignment of FLC molecules is provided by generation of photo-aligning surface on the inner side of PCF structure. Propagation of light spectrum, as well as light attenuation have been investigated in details. Moreover, the electro-optical response times were measured and analysed.     

Dielectric and electro-optical properties of Mn12-acetate and ferroelectric liquid crystal composite

The impact of single-molecule magnet (SMM), Mn₁₂-acetate, on the dielectric properties of ferroelectric liquid crystal (FLC) has been investigated by dielectric spectroscopy and electro-optical techniques in a dual electrode sample cell (DESC). The temperature-dependent dielectric studies on Mn₁₂-acetate/FLC composite have revealed the enhancement in the ferroelectric (smectic C*) to paraelectric (smectic A*) phase transition temperature by 3.5°C. The relaxation process corresponding to Goldstone mode in the ferroelectric phase of the composite is found to be slower compared to pure FLC sample. The electrical response for an input triangular wave shows the existence of one extra polarisation peak in Mn₁₂-acetate/FLC composite which is ascribed to the induced dipole moment in Mn₁₂-acetate molecule. The electro-optical texture of Mn₁₂-acetate/FLC composite revealed that the incorporation of SMM in FLC significantly improve the memory effect.     

High transmittance blue-phase liquid crystal displays with slit-shaped electrode

A blue-phase liquid crystal displays (BP-LCDs) with slit-shaped pixel and common electrodes structure is proposed to increase the transmittance. It generates not only in plane field between the pixel electrodes, but also fringe field above the common electrodes. As a result, the high transmittance is obtained. The aperture ratio is also improved because of the capacitor between the pixel and common electrodes.     

Switchable anti-peeping film for liquid crystal displays from polymer dispersed liquid crystals

Liquid crystals displays (LCDs) currently dominate the display market, wherein a wide viewing angle is considered as one of the most important characteristics. However, for LCDs with wide viewing angles, some private information inevitably becomes more visible; thus, an LCD with a switchable viewing angle has attracted greater interest. Here, we report a novel switchable viewing angle film that can make the viewing angle of an LCD electrically switchable between ±30° and ±60°, i.e. between an anti-peeping mode and a share mode, by 5.0 V is turned on and off, respectively. The response time necessary to change between the modes is in milliseconds. It is believed that it has potential applications in LCDs with high quality.     

A greener electrochromic liquid crystal based on ionic liquid electrolytes

An electrochromic liquid crystal (ECLC) material composed of only liquid crystal (LC) and ionic liquid (IL) was developed. The LC containing the substituted diphenylacetylene serves as electrochromic (EC) material to realise transmittance and colour change under the direct current (DC) field, while the IL with the designable cation and anion served as electrolyte. Herein, a series of IL electrolytes was screened to investigate how IL tunes the electro-optic performance of the ECLC cell. By testing the electrochemistry window of ILs in EC cells, IL with the [NTf₂]^? anion shows adequate electrochemical stability when the EC material undergoes oxidation and reduction. The electro-optic performance of ECLC containing 1-ethoxy-4-[2-(4-pentylphenyl) ethynyl]-benzene (PEB) and IL was then evaluated by UV-vis spectrometry under the control of an electrochemical work station. Compared with other PEB-IL, PEB-[Bmim][NTf₂] with [Bmim][NTf₂] electrolyte shows a satisfactory transmittance at low operating voltage. Furthermore, Pd NPs in situ formed in [Bmim][NTf₂] reduced the EC potential and improved the light scattering of the ECLC cell. In this work, we also designed a bifunctional device based on polymer dispersed liquid crystal (PDLC) that hosts electrochromic guest molecules, and analysed the electro-optical and electrochromic properties of LC electrolyte mixtures, in order to gain control of the incident daylight and glare in building and automotive applications.     

Enhanced dielectric and electro-optical properties of a newly synthesised ferroelectric liquid crystal material by doping gold nanoparticle-decorated multiwalled carbon nanotubes

In this article, a newly synthesised ferroelectric liquid crystal (FLC) material, namely LAHS 22, has been characterised. The characterisation of the FLC material has been performed using dielectric relaxation spectroscopy, differential scanning calorimetry and polarisation optical microscopy. We observed an enhancement in the dielectric and electro-optical properties of the FLC material by incorporating gold nanoparticles (GNPs)-decorated multiwalled carbon nanotubes (MWCNTs). The GNPs-decorated MWCNTs cause an increment in dielectric dispersion (up to kHz), absorption, spontaneous polarisation and rotational viscosity of the FLC material. The pure and GNPs-decorated MWCNTs doped FLC cells were analysed by means of various dielectric spectroscopic and optical measurements. The observed enhancement in the dielectric and electro-optical properties of the FLC material has also been studied with concentration of GNPs-decorated MWCNTs in FLC material. The GNPs-decorated MWCNTs/FLC composites are not only of fundamental importance, but also useful materials for device applications such as liquid crystal displays and memory devices.     

Effects of functionality of thiol monomer on electro-optical properties of polymer-dispersed liquid crystal films

In this paper, polymer-dispersed liquid crystal (PDLC) films which based on the acrylate and the thiol monomers were first prepared by ultraviolet-initiated polymerisation. The electro-optical properties and morphologies of the PDLC films were systematically investigated. The functionality of thiol monomers and their feed ratio showed great influence on the properties of the fabricated PDLC films because of the existence of competition between thiol–acrylate reaction and acrylate monomer polymerisation reaction. This made the polymer network and electro-optical properties of the PDLC films easily tunable by the introduction of the thiol monomers. When added four-functional thiol monomer PETMP with appropriate concentration into the PDLC system, lower driven voltage and higher contrast ratio were achieved.     

Three-dimensional corrugated electrode structure for low-voltage high-transmittance blue-phase liquid crystal displays

We propose new electrode designs for the corrugated Polymer-Stabilised Blue-Phase Liquid Crystal Displays (PSBP-LCDs). In these new designs, the electrode structure varies not only in x/z-axis directions but also in the y-axis (transverse) direction. In this way, an additional electric field is created in transverse y-axis direction which is found to help improve the transmission of the dead zones that exist in the previously proposed corrugate PSBP-LCD structure. The transmission can increase by about 5% to 8 % or higher, depending on the period of the corrugated structure. Using these new structures, it is possible to obtain > 90% in transmission with low operation voltage of about 10 V.     

Low-frequency relaxation modes in ferroelectric liquid crystal/gold nanoparticle dispersion: impact of nanoparticle shape

Low-frequency (1 mHz–100 Hz) dielectric relaxation modes were experimentally studied in ferroelectric liquid crystal (FLC)/gold nanoparticles (nanospheres and nanorods) dispersion. It was demonstrated that the dielectric spectra of nanodispersion are strongly influenced by the shape of nanoparticles. Using different formalisms of the impedance spectroscopy, three possible low-frequency relaxation processes were found in the dispersions and the pure FLC. Due to the electrical double layers (EDLs) near nanoparticles and the alignment layers, one can observe the relaxation of the EDL polarisation around the nanoparticles (Schwarz’s relaxation) and near the driving indium tin oxide (ITO) electrodes (electrode polarisation). The other possible relaxation process is interfacial polarisation (Maxwell–Wagner mode) in which the frequency is unaffected by the nanoparticles. It was shown that Schwarz’s relaxation frequency strongly depended on the shape and size of the nanoparticles. Moreover, dispersion of nanoparticles significantly reduced direct current conductivity of the FLC mixture.     

氧化石墨烯修饰碳离子液体电极同时测定鸟嘌呤和腺嘌呤

以离子液体1-丁基-3-甲基咪唑六氟磷酸盐为粘合剂制备了碳糊电极,然后将氧化石墨烯滴涂到碳糊电极表面制成了一种新型的氧化石墨烯修饰碳离子液体电极。研究了鸟嘌呤和腺嘌呤在修饰电极上的电化学行为。实验结果表明,在0.1 mol/L醋酸盐缓冲溶液中(pH4.5),鸟嘌呤和腺嘌呤在该修饰电极上具有良好的电化学行为,在2.0×10-7～1.5×10-5mol/L浓度范围内鸟嘌呤和腺嘌呤的浓度在该电极上与电化学响应信号呈良好的线性关系,相关系数分别为为0.992和0.996。信噪比为3时,检出限为1.0×10-8mol/L。     

Collective and molecular dynamics in ferroelectric liquid crystals: from low molar to polymeric and elastomeric systems

Broadband dielectric spectroscopy delivers in the frequency range from 10 Hz to 10¹⁰ Hz two collective dielectric loss processes (soft and Goldstone modes) and one molecular relaxation (β-relaxation). The soft mode and Goldstone mode are assigned to the fluctuation of the amplitude and the phase of the helical superstructure. The β-relaxation corresponds to the libration (hindered rotation) of the mesogene around its long molecular axis. At the SmA–SmC^* phase transition this process does not split or broaden, and the temperature dependence of its relaxation rate does not show any deviation from an Arrhenius-like behavior. Its dielectric strength does not decline at the SmA–SmC^* phase transition. These experimental findings are in contrast to the common explanation of the origin of the saturation polarization (“induced spontaneous polarization”), which is based on the existence of a “free” rotation inside the SmA phase and its strong hindrance in the ferroelectric SmC^* phase. Furthermore, the high frequency results require a reformulation for the (generalized) Landau theory as applied to the SmA–SmC^* phase transition. In comparing low molar mass and polymeric (elastomeric) FLC, the collective and molecular dynamics are qualitatively similar, independent of the molecular architecture (e.g. side-chain, combined main- and side-chain or crosslinked systems).     

Mechanism of electrooptic switching time enhancement in ferroelectric liquid crystal/gold nanoparticles dispersion

It is well established that incorporation of nanoparticles (NPs) in the structure of ferroelectric liquid crystals (FLCs) leads to a decrease in their electrooptic response time. Several approaches have been suggested to explain this effect (decrease in rotational viscosity of FLCs, ions enhanced localised electric field, dipole–dipole interaction among NPs and FLC molecules, FLC ordering). In this article, we will report the role of the voltage divider formed by the structural elements of a FLC cell based on ferroelectric liquid crystal/gold nanospheres (FLC/GNSs) dispersion in enhancement of the switching time. Using the impedance spectroscopic measurements, it was demonstrated that the dispersing of GNSs leads to the increase in the voltage drop on FLC/GNSs layer in comparison with the pristine FLC one. Consequently, the electrooptic response time of the FLC/GNSs cell is faster than that of the pristine one. However, the rotational viscosity of the FLC does not depend on the presence of the GNSs.     

High-frame-rate liquid crystal phase modulator for augmented reality displays

We optimise a new liquid crystal mixture with wide nematic range, high birefringence (Δn), high resistivity, moderate dielectric anisotropy (?ε) and relatively low rotational viscosity for augmented reality display applications. High Δn and large Δε allow a thin cell gap (d ≈ 1.5 μm) to be employed in a reflective liquid-crystal-on-silicon (LCoS) device to achieve 2π phase change at 5 V and 2.87 ms average phase-to-phase response time at 40°C without complicated overdrive circuitry. Such a fast response time enables an LCoS panel to achieve 240 Hz frame rate for field sequential colour operation to avoid image flickering.     

Step-shaped electrode for low-voltage and high-optical-efficiency blue-phase transflective liquid crystal displays

A step-shaped electrode design is proposed for Polymer Stabilised Blue Phase (PSBP) Transflective LCD (TR-LCD). This new electrode design is capable of delivering very high optical efficiency (both T and R) of >95% with operation voltage of ~13 V (or >~90% with ~9 V). The step-shaped electrode helps generate strong horizontal electric fields across the whole cell and suppress the formation of dead zone.     

Fast switching beam steering based on ferroelectric liquid crystal phase shutter and polarisation grating

We report on fast-switching and high-efficient optical beam steering based on a polymerisable liquid crystal polarisation grating (PG) in combination with ferroelectric liquid crystal (FLC) phase shutter. The PG was fabricated in a convenient single-step holographic exposure process using photo-sensitive azo-dye material as alignment layer for liquid crystal (LC) director. A binary electro-optical FLC was employed for circular polarisation selection, which enables the electro-tunable steering of the combined system. The efficiency of 95.7% with 82 μs switching time is obtained for 1064 nm laser. This work provides a versatile candidate for non-mechanical beam steering devices.     

Towards a new class of ferroelectric liquid crystal molecules for nonlinear optical applications

The synthesis of a new molecule specifically designed to exhibit both ferroelectric and nonlinear optical properties is presented. This molecule possesses an optically active phenyl sulphinic group, which introduces a dipole moment directly linked to the chromophore group, with a nitro group in the meta -position. The rest of the molecule comprises a tolane and a benzoate group. Such a structure results in an enantiotropic smectic C*-smectic A phase sequence in its polymorphism. A first measurement of the spontaneous polarization shows a high value. The polymorphism of the racemic homologous molecule possessing the nitro group in the ortho-position is also presented, and also shows the smectic C-smectic A phase sequence.     

Reflective mode of deformed-helix ferroelectric liquid crystal cells for sensing applications

We present a detailed theoretical and experimental study of the reflectance response of a deformed-helix ferroelectric (DHF) liquid crystal (LC) cell to an applied voltage under cross-polarisers. Using a model based on the effective dielectric tensor approximation, we derive simple analytical formulas to design a LC cell with maximum modulation depth and optimal linearity of the electro-optical response intensity versus the electric field. Our experimental results show that the cell works at frequencies up to 10 kHz and exhibits excellent linearity, with a total harmonic distortion as low as ?70 dB. These findings suggest that DHF-LCs can be exploited to develop simple and accurate optical sensors.     

The fabrication of polymer dispersed liquid crystal based on SiO2 photonic crystal template

The conductance of polymer matrix is an important factor for the property of the polymer dispersed liquid crystal (PDLC). The nanographites are dispersed into the polymer matrix for optimising the dielectric conductive property. The synthesised nanoparticles SiO₂ was used as photonic crystal (PC) to work as a template for fabricating PDLC films. A mixture of pre-polymer and liquid crystals (LCs) was infiltrated into the void of the PC and polymerised under ultraviolet light. The void of the PC made uniform the dispersion of the liquid crystals in the films. The optical property of the PDLC films was optimised by doped nanographites and negative charge SiO₂ template. The effect of negative charge SiO₂ and nanographites on the threshold voltage and driving voltage was researched. The morphology of the PDLC films was studied by the FTIR image. The dispersed LCs droplets were uniformly affected by the addition of the nanographites. The LCs droplets dispersed in the polymer were located in the void of the SiO₂ photonic crystal.     

Enhancement of electro-optical response of ferroelectric liquid crystal: the role of graphene quantum dots

We present a pioneer study depicting a significant improvement in the photoluminescence (PL) intensity and display of an expeditious electro-optic response of ferroelectric liquid crystal (FLC) when doped with graphene quantum dots (GQDs). Significant threefold enhancement in PL intensity of GQDs/FLC composite material can be ascribed to the additive combination of emissions from GQDs and FLCs. Furthermore, promptness in electro-optical response by a factor of 34% can be attributed to the lowering of rotational viscosity of the FLC material due to the incorporation of GQDs. These results would certainly be helpful in realisation of highly luminescent and faster generation of LC systems.