Flow-injection determination of iodide ion in nuclear emergency tablets, using boron-doped diamond thin film electrode

The electrochemical determination of iodide was studied at boron-doped diamond thin film electrodes (BDD) using cyclic voltammetry (CV) and flow-injection (FI) analysis, with amperometric detection. Cyclic voltammetry of iodide was conducted in a phosphate buffer pH 5. Experiments were performed using glassy carbon (GC) electrode as a comparison. Well-defined oxidation waves of the quasi-reversible cyclic voltammograms were observed at both electrodes. Voltammetric signal-to-background ratios (S/B) were comparable. However, the GC electrode gives much greater in the background current as usual. The potential sweep rate dependence exhibited that the peak current of iodide oxidation at 1 mM varied linearly (r² = 0.998) with the square root of the scan rate, from 0.01 to 0.30 V s⁻¹. This result indicates that the reaction is a diffusion-controlled process with negligible adsorption on BDD surface, at this iodide concentration. Results of the flow-injection analysis show a highly reproducible amperometric response. The linear working range was observed up to 200 μM (r² = 0.999). The detection limit, as low as 0.01 μM (3σ of blank), was obtained. This method was successfully applied for quantification of iodide contents in nuclear emergency tablets.     

Development of an anodic stripping voltammetric assay, using a disposable mercury-free screen-printed carbon electrode, for the determination of zinc in human sweat

This paper reports on the development of a novel electrochemical assay for Zn²⁺ in human sweat, which involves the use of disposable screen-printed carbon electrodes (SPCEs). Initially, SPCEs were used in conjunction with cyclic voltammetry to study the redox characteristics of Zn²⁺ in a selection of supporting electrolytes. The best defined cathodic and anodic peaks were obtained with 0.1 M NaCl/0.1 M acetate buffer pH 6.0. The anodic peak was sharp and symmetrical which is typical for the oxidation of a thin metal film on the electrode surface. This behaviour was exploited in the development of a differential pulse anodic stripping voltammetric (DPASV) assay for zinc. It was shown that a deposition potential of −1.6 V versus Ag/AgCl and deposition time of 60 s with stirring (10 s equilibration) produced a well-defined stripping peak with E_pa = −1.2 V versus Ag/AgCl. Using these conditions, the calibration plot was linear over the range 1 × 10⁻⁸ to 5 × 10⁻⁶ M Zn²⁺. The precision was examined by carrying out six replicate measurements at a concentration of 2 × 10⁻⁶ M; the coefficient of variation was calculated to be 5.6%. The method was applied to the determination of the analyte in sweat from 10 human volunteers. The concentrations were between 0.39 and 1.56 μg/mL, which agrees well with previously reported values. This simple, low-cost sensitive assay should have application in biomedical studies and for stress and fatigue in sports studies.     

Application of gallium film electrode for elimination of copper interference in anodic stripping voltammetry of zinc

For elimination of copper interference in anodic stripping determinations of zinc at mercury and bismuth film electrodes gallium ions are usually added to the supporting electrolyte. In the presented studies novel ex situ formed gallium film electrode was applied for this purpose. The proposed electrode is less toxic than mercury one while the detection limit for zinc was lower than for bismuth film electrode following the same deposition time. The calibration graph for deposition time of 60 s was linear from 5 × 10⁻⁸ to 2 × 10⁻⁶ mol L⁻¹. The determinations of zinc were carried out from undeaerated solutions. The proposed procedure was applied to zinc determination in certified reference material and tap water sample.     

电化学沉积制备纳米结构铜电极及其葡萄糖检测性能

利用电化学沉积法制备了高电活性的纳米结构铜电极材料, 采用扫描电子显微镜和电化学方法分别对电极表面形貌和电化学性能进行了表征, 研究了实验参数对葡萄糖电氧化活性的影响. 结果表明, 改变沉积条件可以调控沉积铜的形貌及电催化活性. 在最佳条件下制备的铜纳米结构电极对葡萄糖检测的灵敏度为1310 μA·L/mmol, 检出限为5.0×10^-7 mol/L(S/N=3).     

Electrochemical characteristics of conductive carbon cement as matrix for chemically modified electrodes

Conductive carbon cement (CCC) was evaluated as matrix material for the preparation of electrodes bulk-modified with electrocatalysts. For pure CCC electrodes the background current characteristics were examined. In acidic or neutral phosphate buffers the useful electrode potential range was from −0.3 to + 1.0 V vs. SCE, while in 0.1 mol 1⁻¹ NaOH it was from −0.3 to + 0.7 V. The electrochemical reversibility of CCC electrodes was examined by measuring the standard rate constants for the reduction of hexacyanoferrate (III) and the oxidation of hydroquinone, using cyclic voltammetry (CV) and rotating disk experiments. The reversibility of a CCC electrode was comparable with that of a freshly polished glassy carbon electrode and better than that of carbon paste electrodes. CCC was used as matrix for the preparation of electrodes bulk-modified with cuprous oxide and cobalt phthalocyanine (CoPC). With a Cu₂O-CCC electrode the oxidation potential of glucose, which shows sluggish kinetics at unmodified carbon electrodes, was strongly reduced. The kinetics of the mediated glucose oxidation has been studied with a rotating disk electrode. It was shown that at glucose concentrations higher than approximately 1 mmol l⁻¹ the electrochemical regeneration of the catalyst becomes rate-determining. The Cu₂O-CCC modified electrode has been applied with a constant potential in flow-injection analysis for the determination of glucose. The long-term stability of the electrode was studied; repeated injections of a glucose solution during a period of 6 h yielded a relative standard deviation of the peak height of 1.8% (n = 57). In CV experiments the electrocatalytic activity of CoPC was shown for the oxidation of various compounds such as penicillamine, hydrazine and bile acids. Application of the CoPC-CCC electrode for the detection of bile acids in flow-through detection with a constant or pulsed potential failed, due to a rapid deactivation of the electrode.     

A competitive immunochromatographic assay for testosterone based on electrochemical detection

An immunochromatographic assay using nitrocellulose membrane was combined with electrochemical detection using an electrode chip in order to quantitatively detect testosterone as a model analyte. The electrode chip consisted of a gold working electrode, a counter electrode and a pseudo-reference electrode, all fabricated on the bottom of a 3.2 mm × 3.2 mm well. Competitive immunoreactions on the membrane were initiated by flowing a solution containing testosterone and horseradish peroxidase (HRP)-labeled testosterone (a competitor) over the membrane. Prepared membrane was placed in a solution containing ferrocenemethanol (FcOH) and H₂O₂ in the well of the electrode chip, and the enzyme reaction was detected by amperometry. Labeled HRP captured on the membrane catalyzed the oxidation of FcOH to the oxidized form FcOH⁺, which was reduced electrochemically by the electrode chip. The electrochemical response of the reduction current decreased with increasing concentration of testosterone over the range 1–625 ng/ml.     

Measurements of trace concentrations of mercury in sea water by stripping chronopotentiometry with gold disk electrode: influence of copper

A stripping chronopotentiometric method, using a rotating gold disk electrode for mercury measurements in sea water is described. Compared with a same method using a stationary gold film electrode, this method has a eight times higher sensitivity and a detection limit of 5 ng l⁻¹ after 10 min deposition time. Moreover, the time needed for gold plating is eliminated. Compared with other electrochemical methods capable of measuring mercury at low concentrations, the present method is more simplified with no degassing step and no need to use a medium-exchange procedure before the stripping step. These characteristics render the method easily practicable on board oceanographic vessels for ‘in situ’ measurements.     

A flow injection method for the analysis of tetracycline antibiotics in pharmaceutical formulations using electrochemical detection at anodized boron-doped diamond thin film electrode

A method using flow injection (FI) with amperometric detection at anodized boron-doped diamond (BDD) thin films has been developed and applied for the determination of tetracycline antibiotics (tetracycline, chlortetracycline, oxytetracycline and doxycycline). The electrochemical oxidation of the tetracycline antibiotics was studied at various carbon electrodes including glassy carbon (GC), as-deposited BDD and anodized BDD electrodes using cyclic voltammetry. The anodized BDD electrode exhibited well-defined irreversible cyclic voltammograms for the oxidation of tetracycline antibiotics with the highest current signals compared to the as-deposited BDD and glassy carbon electrodes. Low detection limit of 10 nM (signal-to-noise RATIO = 3) was achieved for each drug when using flow injection analysis with amperometric detection at anodized BDD electrodes. Linear calibrations were obtained from 0.1 to 50 mM for tetracycline and 0.5–50 mM for chlortetracycline, oxytetracycline and doxycycline. The proposed method has been successfully applied to determine the tetracycline antibiotics in some drug formulations. The results obtained in percent found (99.50–103.01%) were comparable to dose labeled.     

Amperometric glucose biosensor based on electrodeposition of platinum nanoparticles onto covalently immobilized carbon nanotube electrode

A new amperometric biosensor for glucose was developed based on adsorption of glucose oxidase (GOx) at the gold and platinum nanoparticles-modified carbon nanotube (CNT) electrode. CNTs were covalently immobilized on gold electrode via carbodiimide chemistry by forming amide linkages between carboxylic acid groups on the CNTs and amine residues of cysteamine self-assembled monolayer (SAM). The fabricated GOx/Au_nano/Pt_nano/CNT electrode was covered with a thin layer of Nafion to avoid the loss of GOx in determination and to improve the anti-interferent ability. The immobilization of CNTs on the gold electrode was characterized by quartz crystal microbalance technique. The morphologies of the CNT/gold and Pt_nano/CNT/gold electrodes have been investigated by scanning electron microscopy (SEM), and the electrochemical performance of the gold, CNT/gold, Pt_nano/gold and Pt_nano/CNT/gold electrodes has also been studied by amperometric method. In addition, effects of electrodeposition time of Pt nanoparticles, pH value, applied potential and electroactive interferents on the amperometric response of the sensor were discussed.

The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for glucose in the absence of a mediator. The linear range was from 0.5 to 17.5 mM with correction coefficient of 0.996. The biosensor had good reproducibility and stability for the determination of glucose.     

Bismuth film electrode for anodic stripping voltammetric determination of tin

The bismuth film electrode (BiFE), in combination with anodic stripping voltammetry, offers convenient measurement of low concentrations of tin. The procedure involves simultaneous in situ formation of the bismuth film electrode on a glassy carbon substrate electrode, together with electrochemical deposition of tin, in a non-deaerated model solution containing bismuth ions, catechol as complexing agent and the metal analyte, followed by an anodic stripping scan. The BiFE is characterized by an attractive electroanalytical performance, with two distinct voltammetric stripping signals corresponding to tin, accompanied with low background contributions. Several experimental parameters were optimized, such as concentration of bismuth ions and catechol, deposition potential, deposition time and pH of the model solution. In addition, a critical comparison is given with bare glassy carbon and mercury film electrodes, revealing the superior characteristics of BiFE for measurement of tin. BiFE exhibited highly linear behavior in the examined concentration range from 1 to 100 μg L⁻¹ of tin (R² = 0.997), an LoD of 0.26 μg L⁻¹ tin, and good reproducibility with a calculated R.S.D. of 7.3% for 10 μg L⁻¹ tin (n = 10). As an example, the practical applicability of BiFE was tested with the measurement of tin in a real sample of seawater.     

Temporal evolution of Raman intensities on surface-enhanced Raman scattering active copper and gold electrodes at negative potentials

The effect of a roughening procedure on surface-enhanced Raman scattering (SERS) intensity of pyridine at copper and gold electrodes subjected to negative potential has been investigated. Among four procedures tested for a copper electrode the one consisting of electrochemical activation in a solution of LiCl and CuCl₂ resulted in the most stable and effective surface. It was proved that the presence of pyridine during the pretreatment procedure caused a very fast, irreversible decay of SERS intensity for both copper and gold electrodes. Quite stable, at least at room temperatures, gold surfaces were obtained by oxidation-reduction cycles activation in KCl solution.     

A novel fluorometric detection of Cu(2+) based on self-assembled bilayers

Fluorescent reagent sodium 1-naphthylamine diacetate (NADA) was assembled onto gold electrodes via its electrostatic interaction with cysteine (Cys) that was directly assembled on the gold electrode surface. Formation of the self-assembled bilayers was confirmed and primarily characterized by cyclic voltammetry and X-ray photoelectron spectra (XPS). The Cys modification of the gold electrode prevented direct adsorption of NADA onto the gold electrode and hence eliminated fluorescence quenching by gold. Strong fluorescence was observed from the NADA self-assembled bilayers at gold surface and was highly efficiently quenched by Cu²⁺ that allowed for an extremely highly sensitive detection of Cu²⁺ with a detection limit of 0.2 ppt and quantitative detection range of 0.5–9 ppt. The fluorescence from NADA/Cys/Au can be easily regenerated and therefore the present report showed a reusable method for immobilizing reagent in fabricating fluorescent chemosensors.     

The nano-Au self-assembled glassy carbon electrode for selective determination of epinephrine in the presence of ascorbic acid

Gold nanoparticles were self-assembled to the modified glassy carbon electrode (GC) with cysteamine (CA) to prepare the nano-Au/CA/GC modified electrode. The electrochemical behavior of epinephrine (EP) on the modified electrode was explored with cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Epinephrine gave a pair of redox peaks at E_pa = 0.190 mV and E_pc = −0.224 mV (versus SCE), respectively. The nano-Au/CA/GC modified electrode shows an excellent electrocatalytic activity for the oxidation of EP. The modified electrode could be used to determine EP in the presence of ascorbic acid (AA). The response of catalytic current with EP concentration shows a linear relation in the range of 1.0 × 10⁻⁷ to 5.0 × 10⁻⁴ mol L⁻¹ with the correlation coefficient of 0.998. The detection limit is 4.0 × 10⁻⁸ mol L⁻¹. The modified electrode exhibited a good reproducibility, sensitivity and stability for the determination of EP injection.     

Chemically surface-modified carbon nanoparticle carrier for phenolic pollutants: Extraction and electrochemical determination of benzophenone-3 and triclosan

Chemically surface-modified (tosyl-functionalized) carbon nanoparticles (Emperor 2000 from Cabot Corp.) are employed for the extraction and electrochemical determination of phenolic impurities such as benzophenone-3 (2-hydroxy-4-methoxybenzophenone) or triclosan (5-chloro-2-(2,4-dichlorophenoxy)phenol). The hydrophilic carbon nanoparticles are readily suspended and separated by centrifugation prior to deposition onto suitable electrode surfaces and voltammetric analysis. Voltammetric peaks provide concentration information over a 10–100 μM range and an estimated limit of detection of ca. 10 μM (or 2.3 ppm) for benzophenone-3 and ca. 20 μM (or 5.8 ppm) for triclosan.

Alternatively, analyte-free carbon nanoparticles immobilized at a graphite or glassy carbon electrode surface and directly immersed in analyte solution bind benzophenone-3 and triclosan (both with an estimated Langmuirian binding constants of K ≈ 6000 mol⁻¹ dm³ at pH 9.5) and they also give characteristic voltammetric responses (anodic for triclosan and cathodic for benzophenone-3) with a linear range of ca. 1–120 μM. The estimated limit of detection is improved to ca.5 μM (or 1.2 ppm) for benzophenone-3 and ca. 10 μM (or 2.3 ppm) for triclosan. Surface functionalization is discussed as the key to further improvements in extraction and detection efficiency.     

A carbon electrode sputtered with palladium and gold for the amperometric detection of hydrogen peroxide

A modified carbon electrode for the amperometric determination of hydrogen peroxide is described. By deposition of a 15-nm thick layer of a 40:60 mixture of palladium and gold on the surface of the electrode the overvoltages for both the oxidation and the reduction can be decreased by at least 800 mV. When applied as an electrochemical sensor in a flow-injection system, linear calibration graphs were obtained between 10^?7 and 5 × 10^?3 M hydrogen peroxide. The modified electrodes were stable for months.     

Electron transfer of quinone self-assembled monolayers on a gold electrode

Dialkyl disulfide-linked naphthoquinone, (NQ-C_n-S)₂, and anthraquinone, (AQ-C_n-S)₂, derivatives with different spacer alkyl chains (C_n: n = 2, 6, 12) were synthesized and these quinone derivatives were self-assembled on a gold electrode. The formation of self-assembled monolayers (SAMs) of these derivatives on a gold electrode was confirmed by infrared reflection-absorption spectroscopy (IR-RAS). Electron transfer between the derivatives and the gold electrode was studied by cyclic voltammetry. On the cyclic voltammogram a reversible redox reaction between quinone (Q) and hydroquinone (QH₂) was clearly observed under an aqueous condition. The formal potentials for NQ and AQ derivatives were −0.48 and −0.58 V, respectively, that did not depend on the spacer length. The oxidation and reduction peak currents were strongly dependent on the spacer alkyl chain length. The redox behavior of quinone derivatives depended on the pH condition of the buffer solution. The pH dependence was in agreement with a theoretical value of E_1/2 (mV) = E′ − 59pH for 2H⁺/2e⁻ process in the pH range 3–11. In the range higher than pH 11, the value was estimated with E_1/2 (mV) = E′ − 30pH , which may correspond to H⁺/2e⁻ process. The tunneling barrier coefficients (β) for NQ and AQ SAMs were determined to be 0.12 and 0.73 per methylene group (CH₂), respectively. Comparison of the structures and the alkyl chain length of quinones derivatives on these electron transfers on the electrode is made.     

Contribution of migration current to the voltammetric deposition and stripping of lead with and without added supporting electrolyte at a mercury-free carbon fibre microdisc electrode

In order to assess the contribution and analytical significance of migration, electrochemical studies on the deposition and stripping of lead at a carbon fibre microelectrode (diameter of 10 μm) have been undertaken in aqueous solutions containing 1 mM lead ions with variable KNO₃ supporting electrolyte concentrations (10⁻¹ to 10⁻⁵ M), as well as in the total absence of deliberately added supporting electrolyte. The methodology involved the application of cyclic voltammetry to characterise the Pb²⁺ (solution)+2e⁻Pb (metal) process in both the reduction (Pb deposition) and stripping (Pb dissolution) directions. The use of a mercury-free carbon surfaces means that the lead stripping does not occur from the amalgam state, as is commonly the case in anodic stripping voltammetry. In the deposition step, the current rises sharply with potential in response to a lead nucleation-growth process and then reaches an almost potential independent limiting value. The stripping step, obtained on the reverse scan, exhibited oxidation peak currents resulting from the redissolution or stripping of the metal from the electrode surface. The influence of the electrolyte concentration and hence migration current at −0.8 V versus Ag/AgCl for the deposition process, as well on the redissolution peak current and the dependence of the voltammograms on scan rate (10–1000 mV) are discussed. Interestingly, neither deposition limiting nor stripping peak currents vary in a simple manner with added supporting electrolyte concentrations, with maximum values being observed at 10⁻⁵ M rather than zero concentration of added KNO₃. An important implication for the voltammetric determination of lead in low ionic strength media by the very sensitive technique of anodic stripping voltammetry is that use of the method of standard additions commonly employed to minimise unknown matrix problems, is prone to error when contributions to the process from migration current are important.     

Electrochemical behaviour of triclosan at a screen-printed carbon electrode and its voltammetric determination in toothpaste and mouthrinse products

Cyclic voltammetry was used to investigate the electrochemical behaviour of triclosan (2,2,4′-trichloro-2′-hydroxydiphenyl ether) at a screen-printed carbon electrode (SPCE). It was found that a single anodic peak occurred over the pH range 6.0–12.0; this peak was considered to result from an irreversible oxidation reaction at the phenolic moiety. A plot of E_p versus pH was constructed and from the break point a pK_a value of 7.9 was obtained, thus agreeing with the literature value. Detailed voltammetric studies were performed at pH 10, where the analyte exists as an anion. It was demonstrated that, at an initial potential of 0 V, the anion underwent electrosorption prior to electrochemical oxidation. The oxidation reaction appeared to involve a one-electron transfer, as deduced from a calculated n_a value of 0.5; the same value was obtained at pH 7.0. In contrast to triclosan, triclosan monophosphate was found to be electrochemically inactive when subjected to voltammetry under the stated conditions.

The electrochemical oxidation of triclosan at a SPCE was exploited for its determination (0.3%) in commercial toothpaste and mouthrinse products using differential pulse voltammetry. The recovery and precision data indicated that this approach may have application in routine quality control analysis.     

Fabrication of Au‐Nanoparticle/TiO2‐Nanotubes Electrodes Using Electrochemical Methods and Their Application for Electrocatalytic Oxidation of Hydroquinone

Gold nanoparticle (Au‐NPs)‐Titanium oxide nanotube (TiO₂‐NTs) electrodes are prepared by using galvanic deposition of gold nanoparticles on TiO₂‐NTs electrodes as support. Scanning electron microscopy and energy‐dispersive X‐ray spectroscopy results indicate that nanotubular TiO₂ layers consist of individual tubes of about 60–90 nm diameters and gold nanoparticles are well‐dispersed on the surface of TiO₂‐NTs support. The electrooxidation of hydroquinone of Au‐NPs/TiO₂‐NTs electrodes is investigated by different electrochemical methods. Au‐NPs/TiO₂‐NTs electrode can be used repeatedly and exhibits stable electrocatalytic activity for the hydroquinone oxidation. Also, determination of hydroquinone in skin cream using this electrode was evaluated. Results were found to be satisfactory and no matrix effects are observed during the determination of hydroquinone content of the “skin cream” samples.     

A label-free electrochemical immunosensor based on gold nanoparticles for detection of paraoxon

An electrochemical immunosensor for the direct determination of paraoxon has been developed based on the biocomposites of gold nanoparticles loaded with paraoxon antibodies. The biocomposites are immobilized on the glassy carbon electrode (GCE) using Nafion membrane. On the immunosensor prepared paraoxon shows well-shaped CV with reduction and oxidation peaks located −0.08 and −0.03 mV versus SCE, respectively. The detection of paraoxon performed at −0.03 mV is beneficial for guaranteeing sufficient selectivity. The amount of the biocomposite consisting gold nanoparticles loaded with antibodies and the volume of Nafion solution used for fabricating the immunosensor have been studied to ensure sensitivity and conductivity of the immunosensor. The immunosensor has been employed for monitoring the concentrations of paraoxon in aqueous samples up to 1920 μg l⁻¹ with a detection limit of 12 μg l⁻¹.