Radiation detection by using superheated droplets

The superheated emulsion, a radiation detector consisting of superheated droplets dispersed in a gel or a solid matrix, has been in use for some time now. It was initially designed to detect neutrons but also has been modified to detect energetic photons and heavy ions. It has been primarily used as a neutron dosimeter, but has also been used to obtain the energy spectrum for neutrons from Am–Be. The general features of the superheated emulsion detector along with newer analytic methods to obtain more precise results using it as an active device will be presented.     

Effect of a sorbitol nucleating agent on fractionated crystallization of polypropylene droplets

The effect of a sorbitol nucleating agent on crystallization of polypropylene (PP) in droplets was studied. Layer‐multiplying coextrusion was used to fabricate assemblies of 257 layers, in which PP nanolayers alternated with thicker polystyrene (PS) layers. The concentration of a commercial nucleating agent, Millad 3988 (MD) in the layers was varied up to 2 wt %. When the assembly was heated into the melt, interfacial driven breakup of the 12 nm PP layers produced a dispersion of submicron PP particles in a PS matrix. Analysis of optical microscope images and atomic force microscope images indicated that the particle size was not affected by the presence of MD. The crystallization behavior of the particle dispersion was characterized by thermal analysis. In the absence of a nucleating agent, the submicron particles crystallized almost exclusively by homogeneous nucleation at about 40 °C. Addition of a nucleating agent to the PP layers offered a unique opportunity to study the nature of heterogeneous nucleation. Nucleation by MD resulted in fractionated crystallization of the submicron PP particles. The concentration dependence of the multiple crystallization exotherms was interpreted in terms of the binary polypropylene‐sorbitol phase diagram. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1788–1797, 2007     

Study of layered silicate clays as synergistic nucleating agent for polypropylene

Effect of very small quantities of organically modified layered silicate clay on the nucleation of polypropylene (PP), as an additive at ppm levels dosage was investigated, in combination with two of the most commercially exploited organic nucleating agents, one of which is a cyclic aromatic phosphinate salt and the other is bis(3,4‐dimethylbenzylidene) sorbitol, each representing a separate class of nucleating molecules by itself. Substitution of a considerable fraction of either of these organic nucleating agents with organically modified inorganic nanoclay was seen to result in a unique synergy between the two in nucleating PP. Polarized light microscopy studies of these synergistic formulations with organoclay to nucleating agent ratios of 1:1 and 1:3 totaling 0.2 weight percent in PP showed significant reduction in spherulite size from that of non‐nucleated PP, and compared with the samples containing exclusive organic nucleating agent at similar loading. Differential scanning calorimetric studies provided evidence and insight into such synergistic behavior. Crystallization and supercooling temperatures for the synergistic formulations were comparable for those formulations containing only organic nucleating agents, indicating comparable nucleation efficiency, whereas organoclay alone, although showing some extent of nucleation, was clearly poorer in efficiency. Wide and small angle X‐ray scattering studies further explained these observations. An increase in the gamma polytype fraction was seen in samples that contained both organoclay and nucleating agent, pointing to the role of organoclay as a gamma nucleator. Organoclay was found to be completely exfoliated in these synergistic formulations and was seen as well‐dispersed, single platelets in the PP matrix. A hybrid network consisting of exfoliated organoclay platelets and organic nucleating agent molecules was proposed, which is more stable and stiffer than the network formed by nucleating agent alone. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1786–1794, 2010     

Evaporation rate of nucleating clusters

The Becker-D?ring kinetic scheme is the most frequently used approach to vapor liquid nucleation. In the present study it has been extended so that master equations for all cluster configurations are included into consideration. In the Becker-D?ring kinetic scheme the nucleation rate is calculated through comparison of the balanced steady state and unbalanced steady state solutions of the set of kinetic equations. It is usually assumed that the balanced steady state produces equilibrium cluster distribution, and the evaporation rates are identical in the balanced and unbalanced steady state cases. In the present study we have shown that the evaporation rates are not identical in the equilibrium and unbalanced steady state cases. The evaporation rate depends on the number of clusters at the limit of the cluster definition. We have shown that the ratio of the number of n-clusters at the limit of the cluster definition to the total number of n-clusters is different in equilibrium and unbalanced steady state cases. This causes difference in evaporation rates for these cases and results in a correction factor to the nucleation rate. According to rough estimation it is 10(-1) by the order of magnitude and can be lower if carrier gas effectively equilibrates the clusters. The developed approach allows one to refine the correction factor with Monte Carlo and molecular dynamic simulations.     

Extraction of fatty acids from grape seed by superheated hexane

Superheated hexane extraction has been tested for obtaining fatty acids from grape seed and compared with conventional Soxhlet and hot hexane extractions. Seeds from grape residues from a winery were dried for 46 h at 105 °C, milled and sieved by particle size (d < 0.42 mm, 0.42 < d < 0.84 mm and d > 0.84 mm). An optimization study of influential variables on superheated hexane extraction (namely extraction time, temperature, pression, particle size and sample amount) was carried out by a multivariate approach. All the extracts were concentrated in a rotary evaporator and dried by adding 1 g of Na₂SO₄. Then, 2 ml of the dried extract were subjected to reaction with 1 ml of a 0.5 M solution of sodium methylate in methanol to obtain fatty acid methyl esters (FAMEs). After derivatization, FAMEs were quantified by GC-FID. The results show that the optimal conditions for superheated hexane extraction are: time extraction, 10 min; temperature, 80 °C; pressure, 40 bar; particle size, d < 0.42 mm; amount of sample, 0.4 g. Under these conditions, around 84% of the fatty acids (out of the amount obtained by Soxhlet extraction) is extracted. Comparison with Soxhlet and hot hexane extractions showed that the percentages of FAMEs are similar in all the extracts and they agree with the data in the bibliography.     

Encapsulation of emulsion droplets by organo-silica shells

Surfactant-stabilized emulsion droplets were used as templates for the synthesis of hollow colloidal particles. Monodisperse silicone oil droplets were prepared by hydrolysis and polymerization of dimethyldiethoxysiloxane monomer, in the presence of surfactant: sodium dodecyl sulphate (SDS, anionic) or Triton X-100 (non-ionic). A sharp decrease in the average droplet radius with increasing surfactant concentration was found, with a linear dependence of the droplet radius on the logarithm of the surfactant concentration. The surfactant-stabilized oil droplets were then encapsulated with a solid shell using tetraethoxysilane, and hollow particles were obtained by exchange of the liquid core. The size and polydispersity of the oil droplets and the thickness of the shell were determined using static light scattering, and hollow particles were characterized by electron microscopy. Details on the composition of the shell material were obtained from energy-dispersive X-ray analysis. In the case of sodium dodecyl sulphate, the resulting shells were relatively thin and rough, while when Triton X-100 was used, smooth shells were obtained which could be varied in thickness from very thick ( approximately 150 nm) to very thin shells ( approximately 17 nm). Finally, hexane droplets were encapsulated using the same procedure, showing that our method can in principle be extended to a wide range of emulsions.     

Production of microspherical aerosilogels by spray drying in a superheated steam

The effect of spray drying of aerosil dispersions in a superheated steam on the formation of microspherical grains and their pore structure was studied.     

H atom kinetics in superheated water studied by muon spin spectroscopy

It is possible to study H atom chemistry in aqueous systems over a wide range of conditions, from standard to supercritical, using the exotic atom muonium (Mu) as an effective light isotope of hydrogen. The Mu rate constants exhibit marked non-Arrhenius behaviour, going through a maximum and fall-off as the density is reduced in the neighbourhood of the critical point, and subsequent recovery as the medium becomes more gas-like. This is illustrated with new kinetic data for the reaction of Mu with methanol.     

A study of EWOD-driven droplets by PIV investigation

Despite the recent interest in droplet-based microfluidics using electrowetting-on-dielectric (EWOD), fundamental understanding of the fluid dynamics remains limited to two-dimensional (2D) reduction of the Navier-Stokes equation. Experimental data are in dire need to verify the predictions and advance the field. We report an investigation of the flow inside droplets actuated by EWOD in air using micro particle image velocimetry (micro-PIV). Using the continuity equation, we reconstruct the 3D velocity field from the 2D PIV experimental data. We present some fundamental findings and build valuable insights that will help design sophisticated EWOD microfluidic devices. For example, the results confirm that efficient mixing in a droplet may be achieved by moving the droplet along an irreversible pattern that breaks the symmetry of the two circulating inner flows.     

Asymmetric electrowetting--moving droplets by a square wave

Here droplet oscillation and continuous pumping are demonstrated by asymmetric electrowetting on an open surface with embedded electrodes powered by a square wave electrical signal without control circuits. The polarity effect of electrowetting on an SU-8 and Teflon coated electrode is investigated, and it is found that the theta-V (contact angle-applied voltage) curve is asymmetric along the V = 0 axis by sessile drop and coplanar electrode experiments. A systematic deviation of measured contact angles from the theoretical ones is observed when the electrode beneath the droplet is negatively biased. In the sessile drop experiment, up to a 10 degrees increment of contact angle is measured on a negatively biased electrode. In addition, a coplanar electrode experiment is designed to examine the contact angles at the same applied potential but opposite polarities on two sides of one droplet at the same time. The design of the coplanar electrodes is then expanded to oscillate and transport droplets on square-wave-powered symmetric (square) and asymmetric (polygon) electrodes to demonstrate manipulation capability on an open surface. The frequency of oscillation and the speed of transportation are determined by the frequency of the applied square wave and the pitch of the electrodes. Droplets with different volumes are tested by square waves of varied frequencies and amplitudes. The 1.0 microl droplet is successfully transported on a device with a loop of 24 electrodes continuously at a speed up to 23.6 mm s(-1) when a 9 Hz square wave is applied.     

Organic free radicals in superheated water studied by muon spin spectroscopy

There is a pressing need to identify and monitor reaction intermediates in water at high temperatures and pressures, but conventional techniques have limited capability for studying transient free radicals under such challenging conditions. Apparatus has now been developed to permit muon avoided-level crossing spectroscopy (muLCR) of organic free radicals in superheated water. The combination of muLCR with transverse-field muon spin rotation (TF-muSR) provides the means to identify and characterize free radicals via their nuclear hyperfine coupling constants. Because the radicals are derived from the addition of muonium (Mu = mu+ e-) to unsaturated compounds, the ensuing muoniated free radicals correspond to conventional organic free radicals but with a muon spin label substituted for one of the protons. Muon spin spectroscopy is the only technique presently being used to characterize transient free radicals under hydrothermal conditions in an unambiguous manner, free from interference from other reaction intermediates. This paper demonstrates how muoniated radicals can be used to monitor the species present in hydrothermal systems, and examples are presented from two classes of reaction: dehydration of alcohols and enolization of ketones. Spectra are displayed and hyperfine constants reported for muoniated forms of the following free radicals in superheated water (typically 350 degrees C at 250 bar): 2-propyl, 2-methyl-2-propyl (tert-butyl), and 2-hydroxy-2-propyl. The latter radical is the product of muonium addition to both the keto and the enol forms of acetone, but different isotopomers are produced according to which reaction channel is dominant. This should prove invaluable in future studies of the role of enols in combustion.     

Single cell epitaxy by acoustic picolitre droplets

The capability to encapsulate single to few cells with micrometre precision, high viability, and controlled directionality via a nozzleless ejection technology using a gentle acoustic field would have great impact on tissue engineering, high throughput screening, and clinical diagnostics. We demonstrate encapsulation of single cells (or a few cells) ejected from an open pool in acoustic picolitre droplets. We have developed this technology for the specific purpose of printing cells in various biological fluids, including PBS and agarose hydrogels used in tissue engineering. We ejected various cell types, including mouse embryonic stem cells, fibroblasts, AML-12 hepatocytes, human Raji cells, and HL-1 cardiomyocytes encapsulated in acoustic picolitre droplets of around 37 microm in diameter at rates varying from 1 to 10,000 droplets per second. At such high throughput levels, we demonstrated cell viabilities of over 89.8% across various cell types. Moreover, this ejection method is readily adaptable to other biological applications, such as extracting data from single cells and generating large cell populations from single cells. The technique described in the current study may also be applied to investigate stem cell differentiation at the single cell level, to direct tissue printing, and to isolating pure RNA or DNA from a single cell at the picolitre level. Overall, the techniques described have the potential for widespread impact on many high-throughput testing applications in the biological and health sciences.     

Wetting of structured hydrophobic surfaces by water droplets

Super-hydrophobic surfaces may arise due to an interplay between the intrinsic, relatively high, contact angle of the more or less hydrophobic solid surface employed and the geometric features of the solid surface. In the present work, this relationship was investigated for a range of different surface geometries, making use of surface free energy minimization. As a rule, the free energy minima (and maxima) occur when the Laplace and Young conditions are simultaneously fulfilled. Special effort has been devoted to investigating the free energy barriers present between the Cassie-Baxter (heterogeneous wetting) and Wenzel (homogeneous wetting) modes. The predictions made on the basis of the model calculations compare favorably with experimental results presented in the literature.     

Manipulation of droplets by dynamically controlled wetting gradients

The reversible transportation of droplets was realized by spatiotemporal control of the wetting gradient. The surface wetting was reversibly regulated by using electrochemical reactions of the ferrocenyl (Fc) alkanethiol monolayer, and the wetting gradient was generated by the application of the in-plane bias voltage to the substrate. The back-and-forth motion of the wetting boundary, where the surface changed from wetting to repulsive, sequentially caused a droplet unidirectional spreading and shrinking on the surface. These unidirectional deformations resulted in the net transport of the droplet in an inchwormlike manner. The droplet moved backward when the direction of the in-plane bias voltage was reversed.     

Measurement of neutrons from an electron accelerator by rem-counter

In the measurement of neutrons from the medical electron accelerator by a rem counter, two problems disturb accurate measurements. One is the pile-up of signals produced by X-rays during each X-ray burst and the other is the increased counting loss caused by bunched nature of yielded neutrons. The time spectrum of neutrons measured by the rem counter 2202 D (manufactured by Studsvik) rises up to a maximum value by about 20 microseconds and then falls down exponentially with a time constant of about 90 microseconds. On the other hand, that of X-rays is roughly rectangular with several microseconds width. A time discriminating system was prepared to be combined with the rem counter, which was triggered by leading edge of electron beam pulses, rejected pile-up signals due to X-ray bursts, and counted pulses of neutrons in a specified time window. The system discriminated the pile-up enough to measure neutrons at a X-ray dose rate of at least 30 mGy/h. Nonparalyzable counting loss correction was practicable upto about 10 mSv/h for the beam pulse rate of 85 Hz, in which the dead time of the rem counter was estimated as 4 microseconds.     

Activation of enriched environmental xenon by 14-MeV neutrons

The international monitoring system exists to verify compliance with the terms of the comprehensive test ban treaty. About 10% of the member stations will be capable of detecting radioxenon, which can be produced in nuclear detonations or through civilian processes. We have studied the activation of radioxenon by the prompt, intense spectrum of 14-MeV neutrons produced at the National Ignition Facility. While 14-MeV neutrons are not currently a significant contributor to the production of radioxenon, we find that radioxenon produced through activation of environmental xenon by 14-MeV neutrons would be distinguishable from activation by nuclear tests.     

Chromatographic determination of solubilities in superheated water

Superheated water (SHW) is an effective solvent for the extraction of a variety of environmental pollutants, but knowledge of the solubilities in water at elevated temperatures necessary to maximise the efficiency of the process is often lacking. Ambient temperature aqueous solubilities have been measured by reverse‐phase HPLC from correlations with retention factors, k, but for poorly soluble organics the eluent must contain a proportion of organic modifier followed by extrapolation to pure water. The use of SHW as mobile phase allows direct determination of aqueous solubility from measurement of k on a modified HPLC system in which the eluent is cooled before detection to improve baseline stability. Alumina‐bonded octadecylsilane columns were found to be more stable in SHW chromatography than their silica‐bonded counterparts. To validate the procedure, measurements of k were made between 100 and 200°C for toluene and correlated with literature solubilities; the solubilities at 170°C of a number of related aromatics were then determined from their k‐values.