Structure and optical characteristics of poly(p-phenylenevinylene) prepared by vapor deposition polymerization

Films based on poly(p-phenylenevinylene) are prepared by pyrolitic polymerization of α,α′-dichloro-p-xylene. During monomer precipitation, the temperature on a substrate is 25, 50, or ?196°C. Subsequent annealing of the precursor at 250°C yields the final product: the copolymer of p-phenylenevinylene and p-xylylene with an approximate composition of 4: 1. The surface morphology, structure, and optical characteristics of the polymer are studied. The mean-square surface roughness of the precursor is 5 nm. Thermal treatment increase the samples’ roughness up to 10 nm. When the precursor is transformed into poly(p-phenylenevinylene), the roughness coefficient decreases from 0.85 ± 0.05 to 0.74 ± 0.05 owing to the formation of a rougher surface. Characterization of the optical characteristics of the synthesized poly(p-phenylenevinylene) shows that the maximum effective conjugation chain length achieves 12 units in the copolymer prepared when the temperature on the substrate is ?196°C. As the temperature on the substrate increases, the conjugation length decreases to 8 units upon precipitation. Luminescence analysis reveals the effective excitation-energy transfer from short chain fragments of poly(p-phenylenevinylene) to long chain fragments. Electron parameters of the material are estimated: i.e., the band gap, the Huang-Rhys factor, the Stokes shift, and the oscillation energy of molecules.     

Synthesis of 1,1,9,9-tetrafluoro[2.2]paracyclophane and its polymerization by vapor deposition method

1,1,9,9-Tetrafluoro[2.2]paracyclophane ( 1 ) was prepared successfully as white crystals in 72% yield via two-step reactions from 1,9-diketo[2.2]-paracyclophane. The polymerization of 1 by the vapor deposition method was carried out at pyrolysis temperature range of 400 to 800°C and deposition temperature range of ?20 to 20°C, and a tough, transparent poly(α,α-difluoro-p-xylylene) film was obtained in 72% yield at the pyrolysis temperature of 750°C and the deposition temperature of ?20°C. It was found that the pyrolysis of 1 gave a reactive α,α-difluoro-p-xylylene, which polymerized on the head-to-tail addition to give poly(α,α-difluoro-p-xylylene). Some properties such as solubility, thermal stability, glass transition temperature, and density for poly(α,α-difluoro-p-xylylene) were studied. © 1995 John Wiley & Sons, Inc.     

Initial stages of growth of poly(p-xylylene) coatings: AFM study

The morphology of poly(p-xylylene) ultrathin films prepared by vapor deposition polymerization on the surface of single-crystal silicon (100) and on the cleaved surface of mica at a substrate temperature of 20°C has been studied by atomic force microscopy. At the initial stage, the growth of the poly(p-xylylene) coating follows the island mechanism. Within the framework of pyramidal model of island growth, the mean diffusion length for monomer p-xylylene is calculated: For the single-crystal silicon, this parameter is 15 ± 3 nm; for the cleaved surface of mica, 9 ± 2 nm. The nature of the substrate and defects on its surface show a peculiar effect on the structure of the poly(p-xylylene) coating. Thus, at a low monomer flow, nucleation of polymer islands on the surface of silicon is predominantly homogeneous, whereas on the cleaved surface of mica, it is heterogeneous. A change in the monomer flow significantly affects the rate of nucleation of polymer islands.     

Crystallization during polymerization of poly-p-xylylene. II. Polymerization at low temperature

The polymerization of p-xylylene was followed with a newly designed differential thermal analysis system at temperatures between ?196°C and ?20°C. It was found that at the lower temperatures the monomer condenses first to the crystalline monomer before simultaneous polymerization and crystallization. At the higher temperatures, polymerization and crystallization are successive. The data are in agreement with the morphology and crystal structure data derived in Part I of this series of papers on crystallization during polymerization of poly-p-xylylene.     

Polymerization of para-xylylene derivatives. V. Effects of the sublimation rate of di-p-xylylene on the crystallinity of parylene C deposited at different temperatures

Poly(chloro-p-xylylene) was synthesized in a manner similar to poly(p-xylylene) using Gorham's method at various cryogenic temperatures. The effect of the sublimation rate of dimer on the kinetics of deposition, crystallinity, and crystalline structure was studied. Increasing the sublimation rate of the dimer increases the deposition rate similar to that of poly(p-xylylene). However, an increase in crystallinity, in contrast to Parylene N, is observed, although, in general, Parylene C has lower crystallinity relative to Parylene N. No polymorphism is observed either by decreasing the deposition temperature or by increasing the sublimation rate of the dimer. Solution annealing and isothermal annealing both bring about crystallization without any structural transformation. Solution annealing removes the oligomers and dimers, but no crystalline oligomers are ever detected under the scanning electron microscope (SEM). The surface topology of films synthesized from ambient temperature to ?40°C is very similar to Parylene N. At lower temperatures, in the region ?50 to ?60°C, a rod-type morphology is observed similar to Parylene N. The surface topology of samples synthesized at ?196°C is totally different from that of Parylene N. All low temperature synthesized samples are amorphous.     

Crystallization during polymerization of poly-p-xylylene. III. Crystal structure and molecular orientation as a function of temperature

Polymerization of p-xylylene was carried out from the gas phase with monomer produced by the pyrolysis of [2,2]-p-cyclophane. The crystalline form and preferred orientation of as-polymerized polymer deposited at various temperatures (?196 to 80°C) were investigated by x-ray diffraction methods. The melting behavior and other thermal transitions were studied by DSC. At 80°C the polymer film deposit is a mixture of the α and β forms, while between 60 and 0°C the deposit is of the α form. At lower temperature the polymer deposit is mainly of the β form, which shows diffuse reflections. At liquid nitrogen temperature it is of the β form with sharp reflections, contaminated with a small amount of oligomer. It was also found that at low temperatures, fibrillar crystals grow from the substrate in a direction 45° against the gas flow, and at even lower temperature, well-oriented filmlike crystals grow perpendicular to the substrate surface.     

Thermal oxidative stability of poly-p-xylylenes

The air oxidation of poly-p-xylylene films was studied at temperatures between 125 and 200°C. The oxidation kinetics were obtained from neutron activation (NA) oxygen analyses and infrared (IR) Spectroscopy. A correlation between the NA oxygen analyses and mechanical properties indicated that the amount of oxygen incorporated into these polymers before a significant degradation mechanical properties is about 1000 ppm for poly(dichloro-p-xylylene) and 5000 ppm for poly(monochloro-p-xylylene) or poly-p-xylylene. The activation energy for the oxidation of these polymers was about 30 kcal/mole. Long-term-use (100,000 hr) temperatures were also estimated for each of the poly-p-xylylenes studied. The 100,000-hr maximum continuous-use temperature is 112°C for poly(dichloro-p-xylylene), 72°C for poly(monochloro-p-xylylene), and 57°C for poly-p-xylylene.     

A New,General Synthetic Method for the Preparation of Linear Poly-p-xylylenes

A new, general synthetic route to poly-p-xylylene and substituted poly-p-xylylenes is described. The key intermediate in the new process is di-p-xylylene [(2,2)p-cyclophane]. It has been found that di-p-xylylene is quantitatively cleaved by vacuum vapor-phase pyrolysis at 600°C. to two molecules of p-xylylene. p-Xylylene spontaneously polymerizes on condensation to form high molecular weight, linear poly-p-xylylene. The conversion of di-p-xylylene to poly-p-xylylene is quantitative. The process is adaptable to the preparation of a wide variety of substituted poly-p-xylylenes by pyrolysis of ring-substituted di-p-xylylenes and polymerization of the resultant substituted p-xylylenes. Many of these polymers are not attainable by any other route. All are linear and free of crosslinking. Evidence supporting the proposed mechanism of pyrolytic cleavage of every molecule of di-p-xylylene to two molecules of p-xylylene is presented. Tough, transparent polymeric films are obtained from the process when the polymerization of the p-xylylenes is conducted on glass or metal surfaces. Outstanding combinations of physical, electrical, and chemical properties are displayed by poly-p-xylylene, polychloro-p-xylylene, and other substituted polymers. A comparison of the relative merits of the original Szwarc route and the new di-p-xylylene route to poly-p-xylylenes is presented.     

Molecular dynamic simulation of polymer and polymer-oxide nanoclusters

Small systems composed of 10 molecules of poly-p-xylylene or a TiO₂ cluster (rutile) surrounded by 10 molecules of poly-p-xylylene are modeled via the method of molecular dynamics. The thermodynamic characteristics, structure, and mobility of poly-p-xylylene chains in the model systems are studied in a wide temperature interval (195–995 K) and compared with the corresponding characteristics of a volume phase and an individual polymer chain. With increasing temperature, the mobility of monomer units increases; this process leads to disordering. At high temperatures, there is an evident tendency for loosening and further disintegration of an aggregate into individual chains, which adopt a Gaussian coil shape. These transitions are similar to the transitions of the folded individual molecule of poly-p-xylylene. Introduction of a TiO₂ nanoparticle into poly-p-xylylene has a strong effect on the characteristics of the system with short polymer chains, where the adhesion of poly-p-xylylene molecules on the TiO₂ surface is accompanied by disordering in the peripheral region.     

Surface morphology of poly(cyano-p-xylylene) thin films

The surface morphology of poly(cyano-p-xylylene) thin films of different thicknesses (25–1500 nm or more than 5 μm) that were synthesized by vapor-deposition polymerization on the substrate surface in the temperature range from −22 to +35°C has been studied by atomic force microscopy. The surface topography is quantified through analysis of the height-height correlation function. The surface of all films is characterized by a similar granular morphology with a transverse size of granules of 50–500 nm. The surface morphology changes with the polymerization temperature (the substrate temperature) and the film thickness. The effect of film annealing on its surface morphology is considered. It has been established that annealing at 200°C leads to a change in the surface morphology of the films. Original Russian Text ? A.I. Buzin, D.S. Bartolome, K.A. Mailyan, A.V. Pebalk, S.N. Chvalun, 2006, published in Vysokomolekulyamye Soedineniya, Ser. A, 2006, Vol. 48, No. 9, pp. 1640–1646. This work was supported by the Russian Foundation for Basic Research (project nos. 03-03-32665 and 03-03-32634) and the Russian Science Support Foundation.     

Thermal decomposition of poly(α,α,α′,α′-tetrafluoro-p-xylylene) in nitrogen and oxygen

The thermal decomposition of poly(α,α,α′,α′-tetrafluoro-p-xylylene) (parylene AF-4) films with thicknesses of ca. 7.5 and 10 μm has been studied by both dynamic (10°C min^?1) and isothermal TG in either nitrogen or oxygen atmospheres. In dynamic studies with nitrogen, gross decomposition occurs between 546.7±1.4 and 589.0±2.6°C, with 26.8±4.4% of the initial mass remaining at 700°C. With oxygen as the purge gas, the onset of decomposition shifts slightly to 530.8±4.2°C. The end of the transition at 587.4±2.6°C is within experimental error of the nitrogen value, but no polymer remains above 600°C. Isothermal data were obtained at 10°C intervals from 420 to 490°C in nitrogen, and from 390 to 450°C in oxygen. Plots of log(Δ%wt/Δt)vs. T^?1 are linear throughout the specified range for oxygen and from 420 to 470°C for nitrogen. The calculated activation energies of (147±16) kJ mol^?1 and (150±12) kJ mol^?1 in N₂ and O₂, respectively, are equal within experimental error.     

Thermal analysis of poly(p-xylylene) and poly(α,α,α′,α′-tetrafluoro-p-xylylene)

The TG(DTG) and DTA of poly(p-xylylene) and poly(α,α,α′,α′-tetrafluoro-p-xylylene) are reported. The degradation was performed from ambient temperature to 900°C in both air and nitrogen. Both polymer degrade faster in air than under nitrogen but the fluorinated polymer eventually decomposed at higher temperature in air than in nitrogen atmosphere. The activation energies of the degradation processes is given.     

Thermodynamic properties of chitosan-based hydrogels in the range 0–350 K

The heat capacity, the temperature, and the enthalpy of physical transformations of hydrogels based on the copolymer of acrylamide and chitosan with N,N-methylene-bis(acrylamide) as a crosslinking agent, hydrogels based on the mixture of poly(vinylpyrrolidone) and chitosan with glutaric aldehyde as the crosslinking agent, and dehydrated hydrogels has been studied in the range 85–350 K with the use of adiabatic vacuum calorimetry. The temperatures and enthalpies of melting of free water in hydrogels have been determined. From the experimental data obtained, the thermodynamic functions C° _p (T), H° (T) ? H°(0), S° (T) ? S°(0), and G° (T) ? H°(0) have been calculated for the temperature range 0–350 K. The ratio of free and bound water in the hydrogels under study has been determined by calorimetry.     

Etude cinetique de la polymerisation cationique du cyclopentadiene amorcee par l'hexachloroantimoniate de triphenylmethyle

A study of cyclopentadiene polymerization, initiated by φ₃C⁺SbCl₆^? in methylene chloride solution, has been carried out at temperatures between ?70 and +20° using a dilatometric method. An overall external second order with respect to monomer has been found. At very low temperature (?70°), the concentration of active centres remains low and roughly constant, in agreement with a quasi-stationary state assumption. Between ?50 and + 10°, experimental determination of (k_p. M^*), obtained from variation of v_p and [M] with time, shows that the concentration of centres goes through a maximum, sharper and more rapidly reached as the temperature is raised. Initiation is slower than propagation and active centres are rapidly destroyed when termination becomes faster than initiation. This explains the partial conversions and the observed maximum for concentration of active centres. Propagation and unimolecular termination rate constants have been determined at each temperature: activation energies are E_p = ?8 ± 0·5 kcal mole^?1 and E_p = ?0·3 ± 0·1 kcal mole^?1. These negative values can be explained by an exothermic process of solvation of active centres, leading to more reactive propagating species.     

Deposition of copper‐doped iron sulfide (CuxFe1−xS) thin films using aerosol‐assisted chemical vapor deposition technique

Copper‐doped iron sulfide (Cu_xFe_1?xS, x = 0.010–0.180) thin films were deposited using a single‐source precursor, Cu(LH)₂Cl₂ (LH = monoacetylferrocene thiosemicarbazone), by aerosol‐assisted chemical vapor deposition technique. The Cu‐doped FeS thin films were deposited at different substrate temperatures, i.e. 250, 300, 350, 400 and 450 °C. The deposited thin films were characterized by X‐ray diffraction (XRD) patterns, Raman spectra, scanning electron microscopy, energy dispersive X‐ray analysis (EDX) and atomic force microscopy. XRD studies of Cu‐doped FeS thin films at all the temperatures revealed formation of single‐phase FeS structure. With increasing substrate temperature from 250 to 450 °C, there was change in morphology from wafer‐like to cylindrical plate‐like. EDX analysis showed that the doping percentage of copper increased as the substrate temperature increased from 250 to 450 °C. Raman data supports the doping of copper in FeS films. Copyright © 2010 John Wiley & Sons, Ltd.     

Creation of low hysteresis superhydrophobic paper by deposition of hydrophilic diamond-like carbon films

The creation of low hysteresis superhydrophobic paper is reported using a combination of oxygen plasma etching and plasma deposition of an 80 nm non-fluorinated, hydrophilic diamond-like carbon (DLC) coating. The DLC has an equilibrium (flat surface) contact angle (θ _e ) of 68.2° ± 1.5°, which is well below the 90° contact angle that is typically believed to be a prerequisite for superhydrophobicity. Coating of paper substrates with the DLC film yields an advancing contact angle of 124.3° ± 4.1°, but the surface remains highly adhesive, with a receding contact angle <10°. After 60 min of plasma etching and DLC coating, a low hysteresis, superhydrophobic surface is formed with an advancing contact angle of 162.0° ± 6.3° and hysteresis of 8.7° ± 1.9°. To understand the increase in contact angle and decrease in hysteresis, atomic force microscopy and optical profilometry studies were performed. The data demonstrates that while little additional nanoscale roughness is imparted beyond the first 5 min of etching, the roughness at the microscale continually increases. The hierarchical structure provides the appropriate roughness to create low hysteresis superhydrophobic paper from a hydrophilic coating.     

Study of thermal decomposition of poly(vinyl chloride) type polymers with the use of model substances—IV: Gas phase pyrolysis of 2-acetoxy-4-chloropentane

The kinetics of the gas phase pyrolysis were investigated for 2-acetoxy-4-chloropentane, the simplest model for the macromolecule of VC-VAc copolymer; both manometric and GLC method were used. It was concluded that the elimination of the first acid molecule from the model is a homogeneous unimolecular first order reaction with rate constants within the range 310–350° given by: log k₁ = (13·14 ± 0·17)—(44·9 ± 0·5)/2·303 RT for the iso and log k₁ = (13·23 + 0·15)—(44·9 ± 0·4)/2·303 RT for the syndio isomer. (Frequency factors in sec^?1 units, activation energies in kcal mol^?1.)Application of the results to the copolymer leads to the conclusion that the pronounced minimum observed by some authors in the plot of thermal stability against copolymer composition cannot be adequately explained solely in terms of the low thermal stability of an alternating unit.     

Phase transition temperatures of Sn–Zn–Al system and their comparison with calculated phase diagrams

The Sn?CZn?CAl system was studied in connection with the possible substitution of lead-based solders for temperatures up to 350?°C. Ternary alloys with up to 3?wt% of aluminium were prepared. The investigated alloys lie close to the monovariant line (eutectic valley) of the Sn?CZn?CAl system. The temperatures of phase transitions of six binary Sn?CZn reference alloys and fourteen ternary Sn?CZn?CAl alloys using DTA method were investigated in this paper. DTA experiments were performed at the heating/cooling rate of?4?°C?min^?1 using Setaram SETSYS 18_TM experimental equipment. The temperatures of phase transitions in the ternary Sn?CZn?CAl system were obtained, namely, the temperature of ternary eutectic reaction T _E1 (197.7?±?0.7?°C), temperature of ternary transition reaction T _U1 (278.6?±?0.7?°C), temperatures of liquidus and other transition temperatures for studied alloys. Temperatures obtained during DTA heating runs were used as authoritative. DTA curves obtained during cooling enabled realising better differentiation of the obtained overlapped heat effects (peaks) during heating. Theoretical isopleths of the Sn?CZn?CAl phase diagram were calculated using the Thermocalc software and MP0602 thermodynamic database. Experimental data were compared with the calculated temperatures, and a good agreement was obtained.     

Infrared reflection-absorption spectroscopy of polyacrylonitrile on copper and aluminium surfaces

Infrared reflection-absorption spectroscopy has been used to study the chemical structure of thin films of pyrolyzed polyacrylonitrile (PAN) on copper and aluminium surfaces. The formation of a conjugated C? C?C backbone occurs at temperatures as low as 200°C for PAN on copper, whereas the same reaction on aluminium requires pyrolysis at 300°C in order to be completed. These temperatures are, respectively, about 200 and 100°C lower than those previously reported for bulk PAN. Pyrolysis of PAN on copper at 200°C also results in diffusion of copper atoms (ions) into the polymer network followed by Cu(I)? N°C complexing. Conclusive evidence is obtained for end-on coordination through nitrogen lone pair orbitals of the C?N groups. We propose a chemical structure of PAN on copper that is different to that in the bulk and on aluminium.     

Complexation of p-Sulphonato-calix[6]arene by Glycine, Glycyl-glycine, and Glycyl-glycyl-glycine in Aqueous Solution

The complexing ability of p-sulphonato-calix[6]arene towards glycine, glycyl-glycine, and glycyl-glycyl-glycine has been evaluated at pH?=?1.8 and 7.9 using UV?CVis spectrophotometry. At these pHs the guest molecules are in their cationic and zwitterionic forms, respectively. The results showed that the host is capable of complexing with the guests in 1:1 guest-to-host ratios. Formation constants of the systems have been determined at different temperatures (20?±?0.1 to 40?±?0.1?°C). Considering the formation constant values, the binding selectivity of the host towards the guests is in the order glycyl-glycyl-glycine?>?glycyl-glycine?>?glycine. The thermodynamic parameters have been evaluated and are interpreted in terms of the importance of the various interactions responsible for the complexation. A roughly linear relationship between ??H ^o and T??S ^o has been observed for the studied systems and is discussed.