Time and amplitude dependences of the damping decrement and shear modulus upon irreversible structural relaxation in a Zr-Cu-Ni-Al-Ti bulk metallic glass

The time dependences of the irreversible relaxation of the damping decrement and the shear modulus of a Zr_52.5Ti₅Cu_17.9Ni_14.6Al₁₀ bulk metallic glass are investigated using an inverse torsion pendulum in the range from room temperature to ～650 K. The spectrum of activation energies of irreversible structural relaxation is evaluated from the results obtained. Analysis of the amplitude dependences of the damping decrement and the shear modulus allows the conclusion that the relaxation centers responsible for the amplitude dependence differ from those associated with the irreversible structural relaxation at temperatures below and in the vicinity of the glass transition point.     

Irreversible structural relaxation in a bulk Pd-Cu-Ni-P metallic glass

The evolution of the shear modulus and the damping decrement during irreversible structural relaxation in a bulk Pd₄₀Cu₃₀Ni₁₀P₂₀ metallic glass in a temperature range below the glass transition temperature has been studied with an inverse torsion pendulum at a frequency of ～25 Hz. It is shown that the irreversible relaxation can be recovered via quenching from temperatures above the glass transition temperature. The spectrum shape, the characteristic activation energies, and the attempt frequencies of the irreversible structural relaxation are estimated.     

Viscoelasticity and morphology of an organic hybrid of chlorinated polyethylene and N,N′-dicyclohexyl-2-benzothiazolyl sulfenamide

The viscoelasticity and morphology of an organic hybrid of chlorinated polyethylene (CPE) and N,N′-dicyclohexyl-2-benzothiazolyl sulfenamide (DBS) were studied by means of tensile and shear complex modulus and differential scanning calorimetry (DSC) analysis. Tensile and shear loss modulus (E″ and G″), which are shown as indexes of vibration damping performance, showed one peak corresponding to the glass transition. The peak maximum values (E″_max and G″_max)increased in proportion to DBS content ( _DBS) and the slope of E″_max against _DBS became steep above a certain DBS content, i.e. the critical DBS content ( _c). A high damping material was obtained by the addition of DBS, especially when DBS content was higher than _c. These increases in loss moduli below and above _c are caused by the interaction between CPE and DBS molecules and the friction between DBS molecules, respectively. It was found that CPE/DBS is a compatible blend at all DBS contents from the analysis of the glass transition temperature with DSC. Furthermore, the influence of chlorine content in CPE on those characteristics was investigated. Higher chlorine content led to lower _c, a decrease in E″ below _c and an increase in E″ above _c. These results are due to the increase in the number of dichloromethylene units (CCl₂), which reduces the α-hydrogen atom in CPE.     

Isothermal kinetics and relaxation recovery of high-frequency shear modulus in the course of structural relaxation of Pd<Subscript>40</Subscript>Cu<Subscript>30</Subscript>Ni<Subscript>10</Subscript>P<Subscript>20</Subscript> bulk glass

Isothermal kinetics of relaxation of the high-frequency (1.4 MHz) shear modulus during structural relaxation of Pd₄₀Cu₃₀Ni₁₀P₂₀ bulk metallic glass below the glass transition temperature is studied by an in situ method of contactless electromagnetic acoustic transformation. The kinetic law of relaxation is established. It is shown that quenching of aged samples from the supercooled liquid state leads to a decrease in the absolute value of shear modulus to below the initial value; the degree of subsequent isothermal relaxation of the modulus may be several times higher than the initial value. Possible reasons for relaxation and recovery of the shear modulus are considered.     

Thermal effects induced during heating of the bulk metallic glass Zr46Cu46Al8

It has been shown that thermal effects measured calorimetrically during heating of the bulk metallic glass Zr₄₆Cu₄₆Al₈ can be interpreted as a result of the annihilation or generation of structural “defects,” which are similar in their properties to interstitial dumbbells in simple crystalline metals. The shear susceptibility, which characterizes the sensitivity of the shear modulus of the glass to the concentration of “defects” of the type of interstitial dumbbells, has been calculated.     

On the nature of low-temperature anomalies of the anelastic properties of metallic glasses

In Memory of A. M. Roshchupkin The low-temperature (30<T<300 K) internal friction and elastic modulus of the metallic glass (MG) Ni₆₀Nb₄₀ subjected to preliminary cold working by rolling, high-temperature uniform straining, or electrolytic hydrogenation is investigated. It is established that cold rolling, which induces localized plastic flow, or hydrogenation radically alters the temperature dependences of the internal friction and elastic modulus: hysteresis appears in the background damping and intense relaxational peaks arise in the internal friction, accompanied by a defect of the elastic modulus. A uniform strain does not affect the low-temperature anelastic behavior of MGs. Microplastic deformation is observed to accompany the hydrogenation of weakly loaded samples. It is asserted that localized microplastic deformation also occurs on hydrogenation with no load. Plastic flow accompanying both rolling and hydrogenation occurs by the formation and motion of dislocationlike defects, which in the presence of an external load of alternating sign give rise to the observed anelastic anomalies. It is concluded that the low-temperature internal-friction peaks, described in the literature, in the “as-quenched,” cold-deformed, or hydrogenated MGs are all of a dislocation nature. Zh. Tekh. Fiz. 67, 35–46 (October 1997) In Memory of A. M. Roshchupkin     

Elastic properties and spectroscopic studies of lithium lead borate glasses

Elastic properties of xLi₂O — 20PbO — (80-x)B₂O₃ glasses have been measured at a frequency of 10 MHz using X-cut and Y-cut quartz transducers. The trends in the variation of elastic moduli, Poisson’s ratio and Debye temperature have been studied. The elastic moduli namely longitudinal and young’s modulus show strong linear dependence while bulk and shear modulus vary marginally as a function of Li₂O concentration. The Poisson’s ratio is found to be almost constant and Debye temperature increases with the increase of Li₂O concentration. IR, MAS-NMR and glass transition temperature studies have been also carried out. Glass transition temperature is found to increase with increase of Li₂O concentration. IR and MAS-NMR spectra show characteristic features of borate network and systematic change as a function of Li₂O concentration. The variation in the elastic properties and structural features of IR and MAS-NMR indicate that Pb²⁺ ions are likely to occupy network forming positions in this glass system. Paper presented at the 2nd International Conference on Ionic Devices, Anna University, Chennai, India, Nov. 28–30, 2003.     

DSC and elastic moduli studies on tellurite-vanadate glasses containing antimony oxide

xSb₂O₃-40TeO₂-(60 − x) V₂O₅ glasses with 0 ≤ x ≤ 10 (in mol%) have been prepared by rapid- melt quenching method. DSC curves of these ternary glasses have been investigated. The glass transition properties that have been measured and reported in this paper, include the glass transition temperature (T _g ), glass transition width (ΔT _g ), heat capacity change at glass transition (ΔC _P ) and fragility (F). Thermal stability, Poisson’s ratio, fragility and glass forming tendency of these glasses have been estimated, to determine relationship between chemical composition and the thermal stability or to interpret the structure of glass. In addition, Makishima and Makenzie’s theory was applied for determination of Young’s modulus, bulk modulus and shear modulus, indicating a strong relation between elastic properties and structure of glass. Generally, results of this work show that glass with x = 0 has the highest shear, bulk and Young’s moduli which make it as suitable candidate for the manufacture of strong glass fibers in technological applications; but it should be mentioned that glass with x = 8 has higher handling temperature and super resistance against thermal attack.     

Relation between elastic modulus and glass softening temperature in the delocalized atom model

The ratio of softening temperature (glass transition temperature) to elastic modulus (T _g /E) is mainly determined by the limiting elastic deformation of an interatomic bond, which characterizes the transition of a structural microregion from an elastic into a viscous-flow state. In silicate glasses, this transition is caused by the limiting deformation of directed ionic-covalent Si-O-Si bonds. In the case of amorphous hydrocarbons, it is related to the relatively weak intermolecular bonds between regions in chain macromolecules, and the T _g /E ratio is significantly higher than in inorganic glasses. In glassy systems of one class, this ratio turns out to be constant (T _g /E ?? const), and a linear correlation is detected between softening temperature and elastic modulus, which can be explained in terms of the delocalized atom model. The values of T _g /E can be used to classify glasses similarly to the well-known Angell classification according to so-called fragility.     

密度泛函理论研究高温高压下UO2弹性与热力学性能

采用第一性原理与准谐德拜模型研究UO2在高温高压条件下的弹性与热力学性能。UO2在高温高压下仍属离子型晶体,并且弹性性能计算表明,四角方向剪切常数在高温与高压下均保持稳定。高温下弹性常数C44没有明显变化,而高压下C44迅速增大。体积模量、剪切模量与杨氏模量均随压强增加而增大;高温条件下,体积模量、剪切模量与杨氏模量也未出现明显的降低,表明UO2在高温度高压下均可保持良好的力学性能。不同压强下,UO2定容热容均随温度迅速增大,并在1000 K 附近趋近于杜隆-佩蒂特极限。德拜温度则随温度降低,随压强升高。在低于室温条件下,热膨胀系数随温度急剧增加;温度继续增加,系数的增加趋势则逐渐变缓。计算结果还表明,UO2的热膨胀系数在相同条件下,远小于其他核材料。     

Ideal shear banding in metallic glass

As the most fundamental deformation mechanism in metallic glasses (MGs), the shear banding has attracted a lot of attention and interest over the years. However, the intrinsic properties of the shear band are affected and even substantially changed by the influence of non-rigid testing machine that cannot be completely removed in real compression tests. In particular, the duration of the shear banding event is prolonged due to the recovery of the stressed compliant frame of testing machine and therefore the temperature rise at the operating shear band is, more or less, underestimated in previous literatures. In this study, we propose a model for the ‘ideal’ shear banding in metallic glass. The compliance of the testing machine is eliminated, and the intrinsic shear banding process is extracted and investigated. Two important physical parameters, the sliding speed and the temperature of shear band, are calculated and analysed on the basis of the thermo-mechanical coupling. Strain-rate hardening is proposed to compensate thermal softening and stabilise the shear band. The maximum value of the sliding speed is found to be on the order of 10 m/s at least, and the critical temperature at which strain-rate hardening begins to take effect should reach as high as 0.9T_g (T_g is the glass transition temperature) for a stable shear banding event in metallic glass according to the early experimental data. This model can help to understand and control the shear banding and therefore the deformation in MGs.     

Role of manganese ions on the stability of ZnF2-P2O5-TeO2 glass system by the study of dielectric dispersion and some other physical properties

ZnF₂-P₂O₅-TeO₂ glasses containing different concentrations of MnO (ranging from 0 to 0.6%) were prepared. A number of studies, viz. differential thermal analysis, optical absorption, thermo luminescence, infrared spectra, magnetic susceptibility, elastic properties (Young's modulus Y, shear modulus n and micro hardness H) and dielectric properties (constant ε, loss tan δ, a.c. conductivity σ_ac over a range of frequency and temperature and dielectric breakdown strength), of these glasses were carried out as a function of manganese ion concentration. The analysis of the results indicate manganese ions mostly exist in Mn²⁺ state in these glasses when the concentration of MnO≤0.4% and above this concentration manganese ions predominantly exist in Mn³⁺ state; from this analysis an attempt is made to identify the role of these ions on the stability of glass network.     

二元Ni-Al合金极端条件下的弹性和热力学性能：全电子准谐波近似 cited: 1)

通过在原子尺度上建模来研究Al、NiAl和Ni₃Al合金在极端高温和高压下的点阵常数、弹性常数、弹性模量、泊松比和弹性各向异性因子等性质．计算得到的弹性常数均满足相应的力学稳定条件．由于NiAl和Ni₃Al具有较高的B=G值,在0～30 GPa内都属于延展性材料．通过包含电子热运动对体系吉布斯自由能贡献的全电子准谐近似方法,得到了高温高压下Al、NiAl和Ni₃Al合金的热膨胀系数、体积模量、热容和熵等．计算值与已有的实验值和理论值符合较好     

Strength and equation of state of molybdenum triboride under 80 GPa pressure,using radial X-ray diffraction

The strength and equation of state of molybdenum triboride have been determined under nonhydrostatic compression up to 80?GPa, using an angle-dispersive radial X-ray diffraction technique in a diamond anvil cell (DAC). The RXD data yield a bulk modulus and its pressure derivative as K_0?=?342(6)?GPa with K₀′?=?2.11(17) at ψ?=?54.7°. Analysis of diffraction data using the strain theory indicates that the ratio of differential stress to shear modulus (t/G) ranges from 0.002 to 0.050 at pressures of 4–80?GPa. Together with theoretical results on the high pressure shear modulus, our results here show that molybdenum triboride sample under uniaxial compression can support a differential stress of ～10?GPa when it started to yield with plastic deformation at ～30?GPa. In addition, we draw a conclusion that MoB₃ is not a superhard material but a hard material.     

Effect of heat treatment on the elastic characteristics of a bulk amorphous Zr-Cu-Ni-Al-Ti alloy

The changes in the elastic properties of a bulk Zr_52.5Cu_17.9Ni_14.6Al₁₀Ti₅ metallic glass exposed to heat treatments at temperatures of up to 700°C were studied by acoustic methods. An anomalous decrease in the alloy shear modulus (to values lower than that in the amorphous state) was found after the first stages of nanocrystallization.     

Frequency and temperature amplitude dependence of complex heat capacity in the melting region of polymers

Amplitude and frequency dependence of reversible melting of polycaprolactone (PCL) and an ethylene octene copolymer (EOM) were studied using temperature-modulated differential scanning calorimetry (TMDSC) (2?10^?1 Hz <f < 0.05 Hz) and shear spectroscopy (dynamic mechanical analysis, DMA) (5?10^?4 Hz < f < 100 Hz). It was found that the excess heat capacity of PCL is constant for temperature amplitudes in the range 5 mK < A_T < 2 K. The excess heat capacity decreases with frequency of temperature perturbation and tends to zero at about 0.1 Hz and 100 Hz for PCL and EOM, respectively. The constant excess heat capacity and the frequency dependence support the idea that reversible melting is related to a relaxation process on the surface of the polymer crystals. The occurrence of such a relaxation process was shown by shear modulus measurements in the same frequency and temperature region. The relaxation process is, in the melting region, much slower than main relaxation (glass transition). At low temperatures, a crossover can be seen, indicating the independence of both processes because of spatial separation. The main relaxation is related to the melt, while the other is related to the crystal surface.     

Elasticity and inelasticity of silicon nitride/boron nitride fibrous monoliths

A study is reported on the effect of temperature and elastic vibration amplitude on Young’s modulus E and internal friction in Si₃N₄ and BN ceramic samples and Si₃N₄/BN monoliths obtained by hot pressing of BN-coated Si₃N₄ fibers. The fibers were arranged along, across, or both along and across the specimen axis. The E measurements were carried out under thermal cycling within the 20–600°C range. It was found that high-modulus silicon-nitride specimens possess a high thermal stability; the E(T) dependences obtained under heating and cooling coincide well with one another. The low-modulus BN ceramic exhibits a considerable hysteresis, thus indicating evolution of the defect structure under the action of thermoelastic (internal) stresses. Monoliths demonstrate a qualitatively similar behavior (with hysteresis). This behavior of the elastic modulus is possible under microplastic deformation initiated by internal stresses. The presence of microplastic shear in all the materials studied is supported by the character of the amplitude dependences of internal friction and the Young’s modulus. The experimental data obtained are discussed in terms of a model in which the temperature dependences of the elastic modulus and their features are accounted for by both microplastic deformation and nonlinear lattice-atom vibrations, which depend on internal stresses.     

Internal friction in Cu6PS5Br superionic crystals and related composites

Mechanical properties of Cu₆PS₅Br single crystals and composites based on them have been investigated by the internal friction method. The measurements of the internal friction and the shear modulus have been performed in the temperature range of 80–300 K at deformation frequencies of 10–100 mHz in a mode of forced torsional vibrations. The maxima caused by the superionic and ferroelastic phase transitions have been found in temperature dependences of the internal friction. It has been shown that a more than two-fold decrease in the shear modulus with increasing temperature in the range of 150–230 K is caused by mobility unfreezing in the cation sublattice of the Cu₆PS₅Br single crystal during the superionic phase transition. An abrupt (more than threefold) increase in the shear modulus upon heating in the range of 260–270 K is caused by the ferroelastic phase transition of the Cu₆PS₅Br single crystal. Parameters of the internal friction of this single crystal in the course of mentioned phase transitions have been determined.     

Investigation on the structural,electronic, elastic and mechanical properties of Ti2Al(C1-xOx) solid solutions: First-principles calculations

In the present work, the structural, electronic, elastic and mechanical properties of Ti₂AlC and Ti₂Al(C_1-xO_x) solid solutions were investigated using first-principles calculations for varied O content incorporation (x = 0, 0.125, 0.25, 0.375, 0.5). According to the calculation results, all Ti₂Al(C_1-xO_x) solid solutions with various x values are stable, and the bonding strength of the Ti–Al bond increases with the doping of O element. In addition, the shear modulus G and C₄₄ elastic constant of Ti₂Al(C_1-xO_x) solid solutions are both lower than the bulk modulus B, indicating that the phase has good damage tolerance. Not only that, compared with Ti₂AlC, the plasticity and toughness of Ti₂Al(C_1-xO_x) solid solutions are improved with the increase of O atom doping and doping ratio. Simultaneously, the doping of O atom is also beneficial to reduce the generalized stacking fault energy of Ti₂AlC, making the Ti₂Al(C_1-xO_x) solid solutions more prone to shear deformation, thereby further enhancing plasticity.