磁控溅射方法生长的氮氧锌薄膜的光学特性

氧化锌(ZnO)是一种具有六方结构的宽禁带Ⅱ--Ⅵ族半导体材料，室温下能带带隙Eg为3.37eV。由于氧化锌在室温条件下具有较高的激子束缚能(60meV)，保证了其在室温下较强的激子发光。此外氧化锌还具有较高的热稳定性和抗化学腐蚀特性，因而被认为是制作紫外半导体激光器的合适材料。自1997年首次发现ZnO室温紫外受激发射以来，ZnO已成为继GaN之后紫外发射材料的又一研究热点。但是，目前对于p型氧化锌及其发光器件的研究仍处于探索阶段，对其光电特性的研究仍需要更多投入。本文利用磁控溅射方法制备出氮氧锌薄膜样品，并通过在氧气气氛下退火处理，改变薄膜样品中氮的含量。通过X射线衍射谱、X射线光电子能谱、光致发光谱及喇曼光谱的测试，研究了氮在氧化锌薄膜中的含量变化以及氮对氧化锌薄膜的结构和光学特性的影响。     

高质量纳米ZnO薄膜的光致发光特性研究

报道了利用低压-金属有机物化学气相沉积技术生长纳米ZnS薄膜，然后，将ZnS薄膜在氧气中于800℃温度下进行热氧化制备高质量纳米ZnO薄膜.x射线衍射结果表明，纳米ZnO薄膜具有六角纤锌矿多晶结构.室温下观察到一束强的紫外(3.26 eV) 光致发光和很弱的深能级发射.根据激子峰的半高宽度与温度的关系确定了激子-纵向光学声子（LO）的耦合强度（ГLO）.由于量子限域效应使ГLO减少较多. 关键词： 光致发光 热氧化 激子 纳米ZnO薄膜     

退火温度对ZnO薄膜结构和发光特性的影响

采用反应射频磁控溅射法在 Si(100)基片上制备了高c轴择优取向的ZnO薄膜，研究了退火温度对ZnO薄膜的晶粒尺度、应力状态、成分和发光光谱的影响，探讨了ZnO薄膜的紫外发光光谱和可见发光光谱与薄膜的微观状态之间的关系.研究结果显示,在600—1000℃退火温度范围内，退火对薄膜的织构取向的影响较小，但薄膜的应力状态和成分有比较明显的变化.室温下光致发光光谱分析发现，薄膜的近紫外光谱特征与薄膜的晶粒尺度和缺陷状态之间存在着明显的对应关系；而近紫外光谱随退火温度升高所呈现的整体峰位红移是各激子峰相对比例变 关键词： ZnO薄膜 退火 光致发光 射频反应磁控溅射 可见光发射     

衬底温度对ZnMgO薄膜结构和光致发光性能的影响

利用超声喷雾热解方法以不同的沉积温度(450～550 ℃)在石英衬底上制备出一系列ZnMgO薄膜。采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和光致发光谱(PL)表征了样品的晶体结构、表面形貌和光学性能。结果表明衬底温度对薄膜结构性能和光学特性影响显著。所有薄膜都呈六角纤锌矿多晶结构,其中在530 ℃条件下制备的样品C轴择优最明显,晶粒尺寸均匀,表面形貌平整,结晶质量最好。薄膜的光致发光谱显示随着温度的升高深能级跃迁范围逐渐减小,近紫外带边发光峰逐步出现。衬底温度为530 ℃时在374.5 nm处出现了明显的近紫外发光峰,且几乎没有明显的深能级跃迁出现。     

氧化锌薄膜Zn/O比和发光性能的关系

用直流反应溅射在硅基片上生长具有高取向晶粒的氧化锌薄膜,在氧气、氮气、空气气氛和不同温度下进行热处理,对所得到的样品用俄歇谱(AES)仪进行元素深层分布分析,并测量光致发光光谱。研究结果表明：1．经热处理的薄膜表面全部为缺氧表面,不同深度Zn和O含量分布(Zn／O)有所不同;2．当在氧气氛中1000℃下热处理后,在薄膜的深层可产生比较明显的氧过量;而在空气中950℃下热处理后,则可产生局部氧过量;3．光致发光谱表明,薄膜中全部为锌过量时产生纯紫外发射,而具有局部氧过量的薄膜则在产生紫外发射的同时产生绿色发光,绿光和紫外的强度比则随局部氧过量增多而增大。     

微纳跨尺度ZnO结构的紫外发射机理研究

利用气相输运的方法在Si(100)衬底上生长了ZnO的微纳跨尺度结构.扫描电镜照片可以明显地看到样品表面为椎顶六角微米柱-纳米棒的复合结构.样品在室温下的光致发光谱出现了很强的紫外发射峰,没有观察到与杂质或缺陷相关的深能级发射,表明样品有很好的光学质量.通过详细的研究样品的紫外发射谱与温度(83—307K)的依赖关系,发现在室温下样品的近带边发射包含两个部分,分别与自由激子发射和自由载流子到施主(受主)的跃迁(FB跃迁)相关,这个施主(受主)束缚态的离化能为124.6meV. 关键词： ZnO微纳跨尺度结构 光致发光谱 自由载流子到施主(受主)的跃迁 自由激子发射     

不同退火温度下氧化锌薄膜可见发光与n型导电研究

采用脉冲激光沉积法在蓝宝石衬底上制备出可见光发光良好的氧化锌薄膜, 在不同的温度下进行了后退火处理. 随着退火温度的升高, 薄膜的可见光发光发生了显著改变, 载流子浓度、迁移率、电阻率也呈现出一定的变化规律. 结合 X射线衍射、扫描电子显微镜、光致发光谱及霍尔测量, 探讨了本征氧化锌薄膜可见光发光的发射机理, 并分析了其 n型导电的原因. 关键词： 氧化锌薄膜 可见光发光 n型导电     

Zno纳米晶的室温紫外受激发射特征

ZnO的激子特性对制备氧化锌基的光电子器件至关霞要,因此对ZnO量子点中激子的发光性质及其跃迁过程进行研究显得十分必要.采用溶胶-凝胶法制备了ZnO纳米晶,X射线衍射(XRD)结果表明样品具有六角纤锌矿多晶结构.研究了在不同泵浦功率激发下ZnO纳米晶的紫外发射的时间积分光谱和时间分辨光谱,观察到自南激子发光,激子-激子碰撞和电子-空穴等离子体引起的受激发射,研究了在不同泵浦功率激发下自由激子及激子-激子碰撞随泵浦功率依赖的动力学过程.研究结果对理解激子带边发射有一定帮助,对ZnO材料在短波长半导体光电器件方面有潜在的应用价值.     

ZnO薄膜近带边紫外发光的研究

用ZnO陶瓷靶,采用脉冲激光沉积(PLD)技术在c-Al₂O₃衬底上制备了ZnO薄膜。通过不同温度下光致发光(PL)光谱的测量,对样品的紫外发光机理进行研究。 在较低温度(10 K)下的PL光谱中,观测到一个位于3.354 eV处的束缚激子(D⁰X)发射,随着温度的升高(~50 K),在D⁰X的高能侧观测到了自由激子的发射峰。在10 K温度下,3.309 eV处出现了一个较强的发光带A,此发光带强度随着温度升高先增大然后减小,并且一直延续到室温。重点讨论了此发光带的起源,并认为A带可归属于自由电子-受主之间的复合发射。     

氟掺杂的氧化锌薄膜的结构和光学特性

通过热氧化氟化锌(ZnF2)薄膜的方法制备出氟掺杂的多晶ZnO薄膜,ZnF2薄膜是利用电子束蒸发方法沉积在Si(100)衬底得到的。利用X射线衍射和X射线电子能谱研究了ZnF2薄膜向ZnO的转变过程。实验结果表明,在400℃退火30min的条件下能够获得六方纤锌矿结构的ZnO：F薄膜。对ZnO：F薄膜的室温光致发光谱可以观察到位于379nm、半峰全宽为73meV的紫外发射峰,而相应于缺陷的深能级发射则完全猝灭。表明ZnO中残留的F能够有效地增强激子的发光,同时使缺陷发光强度明显降低。对F掺杂对ZnO的发光性能的影响进行了讨论。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.