PuO2和α-Pu2O3光学性质的经验势模拟

用GULP程序拟合出α-Pu₂O₃的Pu-O作用BMH经验势参数.结合氧离子壳模型势,运用分子静力学和动力学计算出PuO₂和α-Pu₂O₃理想晶体的结构参数和光学性质.结果显示：它们的空间群、晶胞参数、密度和熵等,与文献报道值接近,相对误差均小于1.2%;并计算出PuO₂和α-Pu₂O₃的高频和静态介电张量、红外介电函数谱、晶格振动 关键词： 2')" href="#">PuO₂ 2O₃')" href="#">α-Pu₂O₃ 光学性质     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

用于α-Al2O3分子动力学模拟的长程Finnis-Sinclair势函数

用金属势函数描述氧化物是实现金属-氧化物界面分子动力学模拟的关键.基于此,通过拟合α-Al₂O₃的晶格能、晶格常数、弹性常数,获得了一套用于描述α-Al₂O₃的长程Finnis-Sinclair（F-S）势.通过与已报道的描述α-Al₂O₃的EAM势、Glue势和modified Matsui（m-Matsui）势的比较,结果达到或优于前人的结果.进而,在300 K的温度下对 关键词： 长程F-S势 2O₃')" href="#">α-Al₂O₃ 2O₃界面')" href="#">Fe-Al₂O₃界面 2O₃界面')" href="#">Al-Al₂O₃界面     

在氧-水蒸气存在下单相Sr2(Gd,Ce)2Cu2RuO10的合成及其电学性质

传统固相反应所合成的锶系钌铜氧化物，通常总伴有少量铁磁性SrRuO₃杂相.采 用氧(或空 气)_水蒸气混合气氛下的新型固相反应，既能成功合成锶系钌铜氧化物的前驱物纯相Sr₂G dRuO₆(211相), 也能进一步在相对低的温度下成功合成锶系钌铜氧1222纯相化 合物RuSr₂(Gd,Ce)₂Cu₂O₁₀ (Ru_1222）， 使其中SrRuO _{关键词： 水蒸气参与的新型固相反应 2}(Gd')" href="#">RuSr₂(Gd 2Cu_{2< /sub>O10纯相')" href="#">Ce)2Cu2< /sub>O10纯相 3杂相')" href="#">SrRuO3杂相 电学性质}     

强冲击压缩下LiF，Al2O3和LiTaO3单晶的透光性

在二级轻气炮上，用高速电子相机扫描照相技术和改进的Mallory实验装置，对z切LiF，Al₂O₃(蓝宝石)和LiTaO₃单晶材料的冲击透光性进行了对比测量，并用黑密度计提取出动态图像定量化的光强对比度变化曲线.结果表明，LiF单晶在102 GPa压强下能够保持长时间的初始透光性不变，与公认的LiF具有优良的高压下透明性的认识一致.LiTaO₃单晶在实验压力(139GPa)下变成基本不透明.而Al_{关键词： 2}O₃')" href="#">Al₂O₃ LiF 3')" href="#">LiTaO₃ 光学透明性     

新型超导体MgB2和MgCNi3热、电输运性质研究

报道了两种新型超导体MgB₂,MgCNi₃和氧化物高温超导体Bi_{2< /sub>Sr2Ca0.9Ce0.1Cu2O8+y 的热导率-温度关系和电阻率-温度关系.实验发现氧化物高温超导 体在进入超导态后热导有所上升，出现极大值后再下降，而MgB2和MgCNi3 则单调下降. 由Wiedemann-Fra 关键词： 热导率 超导体 2}')" href="#">MgB₂ 3')" href="#">MgCNi₃     

Ce4+离子在Ca2SnO4一维结构基质中的电荷迁移光谱研究

利用高温固相反应法制备了Ca₂Sn_1-xCe_xO₄和Ca_2-ySr_ySn_1-xCe_xO₄一维结构发光体. XPS结果显示 Ca₂SnO₄拥有两种结合能分别为5277 eV和5293 关键词： 2Sn_1-xCe_xO₄')" href="#">Ca₂Sn_1-xCe_xO₄ 2-ySr_ySn_1-xCe_xO₄')" href="#">Ca_2-ySr_ySn_1-xCe_xO₄ 一维结构 电荷迁移光谱     

氧流量对热蒸发CVD法生长β-Ga2O3纳米材料的结构及发光特性的影响

用热蒸发CVD法制备了β-Ga₂O₃纳米材料, 并用光致发光(PL)方法研究了其发光特性. Ｘ射线衍射分析显示, 产物为单斜结构的β-Ga₂O₃. 扫描电子显微镜测试表明: 在较小氧流量条件下制备的产物为β-Ga₂O₃纳米带, 宽度小于100nm, 长度有几微米; 较大氧流量时制备出β-Ga₂O₃纳米晶粒结构, 晶粒尺度在80—15 关键词： 光致发光 氧流量 纳米结构 2O₃')" href="#">Ga₂O₃     

ZnFe2O4的固相法和水热法制备及其电化学性能研究

本文用固相反应法和水热法制备了ZnFe₂O₄材料,X射线衍射(X-ray diffraction, XRD)表明制备出来的ZnFe₂O₄为尖晶石结构,表面形貌测试 (scanning electron microscopy, SEM) 显示两种方法制备的材料的平均粒径分别为500 nm和200 nm.比表面积测试结果表明,两种方法制备的样品的比表面积分别为136.7 m² g^{-1关键词： 2O₄')" href="#">ZnFe₂O₄ 尖晶石结构 电化学性能 锂离子电池}     

Y2O3: Eu,Dy的制备与红色长余辉发光性能研究

采用高温固相法合成发光样品Y₂O₃：Eu³⁺_0.01和Y₂O₃：Eu³⁺_0.01,Dy³⁺_0.01.X射线衍射分析(XRD)表明样品保持Y₂O₃晶格结构,掺入的Eu³⁺和Dy³⁺对Y_{2关键词： 长余辉 2}O₃')" href="#">Y₂O₃ 稀土掺杂 陷阱     

Multiplication of electronic excitations in nanophosphors Lu2O3:Eu and Lu2O3:Tb

Luminescence properties of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanocrystalline powders with the particle size varying from 46 to 6 nm were studied under excitation by synchrotron radiation in the photon energy range (up to ∼22.5 eV) covering the region where the processes of multiplication of electronic excitation occur. It was found that the excitation spectra of Tb³⁺ emission from all Lu₂O₃:Tb³⁺ nanopowders have similar behavior, whereas the shape of the excitation spectra of Eu³⁺ emission from Lu₂O₃:Eu³⁺ nanopowders strongly depends on the particle size. The difference in the behavior of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanophosphor systems was explained by different mechanisms of the energy transfer from the host to Eu³⁺ or Tb³⁺ ions (either the hole or electron recombination mechanism, respectively), which are differently influenced by losses of electronic excitations near the particle surface.     

980 nm激发下Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的上转换发光特性

通过固相反应法制备了Er³⁺/Yb³⁺共掺杂ZrO₂-Al₂O₃粉末的样品，并对样品在980nm激光激发下的上转换发光特性进行了研究.从发射光谱可以发现，在可见光范围内有3个强的发光带，一个位于654nm附近的红光带和两个分别位于545nm、525nm附近的绿光带，分别对应于Er³⁺离子的以下辐射跃迁：⁴F_9/2→⁴I_15/2、⁴S_3/2→⁴I_15/2、 ²H_11/2→⁴I_15/2.其中又以Er³⁺离子的⁴F_9/2→⁴I_15/2跃迁产生的红色荧光辐射最强.对其上转换发光机制进行了分析，发现这三个发光过程都是双光子过程.对样品粉末进行了XRD检测，发现ZrO₂主要以立方相为主，并且计算得到了这种立方结构的晶格常数.Al₂O₃固溶于ZrO₂中，Al³⁺嵌入ZrO₂后产生氧空位，导致ZrO₂晶体的对称性降低，这种结构变化更有利于提高上转换效率，即上转换发光强度增强. 关键词： 3+/Yb³⁺')" href="#">Er³⁺/Yb³⁺ 上转换 2-Al₂O₃')" href="#">ZrO₂-Al₂O₃ 荧光 稀土     

Synthesis, characterization, and luminescent properties of Lu2O3:Eu phosphors

Eu-doped lutetia (Lu₂O₃:Eu) nano-phosphors were synthesized by the sol-gel combustion process from a mixed aqueous solution of europium and lutetium nitrates, using organic glycine as the fuel. Powder X-ray diffraction shows that cubic Lu₂O₃:Eu crystallites are directly obtained by the sol-gel combustion process without further calcination. Electron microscopy reveals that the as-prepared phosphors are agglomerated and have a fluffy, fine, and porous morphology, consisting of primary particle size of 8-10 nm. The excitation spectrum is characterized by three dominant bands centered at 395, 466, and 534 nm, respectively. Both the photoluminescent and radioluminescent spectra are very similar and exhibit intense emission peaks centered at 612 nm due to ⁵D₀→⁷F₂ transition of Eu³⁺ ions. The energy transfer from Lu₂O₃ host to Eu³⁺ activator is more efficient in the case of calcined phosphors than for the as-prepared phosphors due to their improved lattice perfection.     

H_3BO_3对Y_(1.98)O_3:Eu_(0.01),Dy_(0.01)红色长余辉发光材料结构和余辉性能的影响

采用高温固相法制备了发光样品Y1.98O3:Eu3+0.01,Dy3+0.01.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、荧光光谱仪、单光子计数器测试了不同含量的H3BO3对Y1.98O3:Eu3+0.01,Dy3+0.01物相结构、颗粒形貌、发光性能、余辉性能的影响.结果表明当H3BO3含量低于8%(mol)时,样品可保持Y2O3晶格结构,且样品颗粒随H3BO3的含量增加逐渐增大.样品光致发光由Eu3+离子电子的5D0→7FJ跃迁所致,主峰位于612 nm,且发光强度随H3BO3含量的增加呈线性增强.随着H3BO3含量的增加,样品余辉衰减时间逐渐增加,热释光谱分析表明H3BO3的加入增加了基质陷阱能级的深度与浓度,故而导致样品长余辉性能的变化.     

SrAl_2B_2O_7:Dy~(3+)材料的制备及其发光性能

采用高温固相法制备了SrAl2B2O7:Dy3+发光材料.在350nm紫外光激发下,测得SrAl2B2O7:Dy3+材料的发射光谱为一个多峰宽谱,主峰分别为480,573和678nm;分别和Dy3+的4F9/2→6H15/2,4F9/2→6H13/2,4F9/2→6H11/2的跃迁发射相对应;监测573nm的发射峰,得到材料的激发光谱为一个多峰宽谱,主峰分别为295,325,350,365,400nm.研究了Dy3+掺杂浓度对SrAl2B2O7:Dy3+材料发射光谱的影响,随着Dy3+掺杂浓度的增大,SrAl2B2O7:Dy3+材料的Iy/Ib逐渐增大,根据Judd-Ofelt理论解释了其原因.随着Dy3+掺杂浓度的增大,Dy3+的4F9/2→6H13/2跃迁产生的573nm发射峰强度先增大,在4%时达到最大值,之后减小,其自身的浓度猝灭机理为电偶极-电偶极相互作用.不同的电荷补偿剂Li+,Na+,K+的引入均使发光强度得到提高,尤其以Li+最佳,发光强度提高了大约33%.     

Luminescent properties of a new green emitting Eu doped CaZrSi2O7 phosphor for WLED applications

CaZrSi₂O₇ (CZS), a modification of the thortveitite family, was prepared as a polycrystalline powder material by the conventional solid-state reaction method. Structural, thermal and photoluminescence (PL) properties of the prepared material were investigated in order to evaluate its potentiality. XRD patterns confirm the monoclinic phase of CaZrSi₂O₇: Eu²⁺ phosphors.. Emissions arising from transitions between the 5d and 4f orbital gaps of Eu²⁺ are manifested in the broadband excitation and emission spectra with major peaks at 363 and 512 nm, respectively. The excitation wavelength matches well with that of the emission of the ultraviolet-light emitting diode (UV-LED). Concentration quenching occurs when the Eu²⁺ concentration is beyond 0.05 and the dipole-dipole interaction was the reason for the corresponding quenching mechanism. The temperature dependence of emission intensity of CZS: Eu²⁺ phosphor was investigated and it showed better thermal stability than the standard YAG: Ce³⁺ phosphor.     

Synthesis of nano-size BaMgAl10O17:Eu blue phosphor by a rapid exothermic reaction

Ultrafine particles of BaMgAl₁₀O₁₇:Eu²⁺ (BAM) phosphor were synthesized by a solid-state combustion reaction in a powder bed of 0.9BaCO₃+MgO+5Al₂O₃+0.05Eu₂O₃+k(KClO₃+1.5C) composition. A large exothermic reaction of the mixture (KClO₃+1.5C) leads to a self-sustaining combustion mode. Under optimized combustion conditions, the product consisted of BAM powder and KCl was obtained. BAM ultrafine particles resulting from the combustion process were easily obtained by simply washing the salt by-product with water. Combustion-processed BAM phosphor shows a homogeneous grain size of 100-500 nm, good dispersity, regular morphology, and improved luminescence properties.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

超声喷雾共沉淀法制备的Lu3Al5O12∶Eu3+ 纳米粉体发光特性

采用新型超声喷雾共沉淀法技术,以Lu₂O₃、Eu₂O₃、Al(NO₃)₃·9H₂O为原料,制备了不同浓度Eu³⁺离子掺杂的Lu₃Al₅O₁₂纳米粉体.用X射线粉末衍射表征了获得纳米粉体的相,用扫描电镜观察了纳米粒子的形貌.测定了粉体的激发光谱、⁷F₀-⁵D₂声子边带谱与发射光谱.研究了不同高温烧结温度与Eu³⁺掺杂浓度对纳米粒子的发光强度与粒子形貌的影响规律.研究表明,当烧结温度高于900 ℃时,粉体发光强度明显增强,并且随着煅烧温度的增加,发光强度有所增强.Eu³⁺离子的最佳掺杂浓度为5~7 mol%.根据稀土离子Eu³⁺光学跃起矩阵元的特点,从发射光谱获得Eu³⁺光学跃起的J-O参量Ω₂与Ω₄.在Eu³⁺掺杂浓度均为5 mol%时,其强度参量达最小,电-声子耦合最强.然后随着掺杂浓度的进一步提高,强度参量略有增加,电-声子耦合减弱.说明Eu-O键强增加,共价性增强,Eu³⁺的局域环境对称性降低.Ω₂值低于Eu³⁺在玻璃与晶体基质中的情况,这是由于纳米粒子中存在着大量的缺陷以及晶体的结构畸变导致纳米粒子的对称性下降所致.