超声微乳法合成TiO2-SiO2催化剂可见光光催化降解亚甲基蓝

采用可见光下亚甲基蓝的光催化降解为模型反应,考察了超声微乳法经钛酸丁酯水解合成的纳米TiO2-SiO2催化剂的性能,并用XRD和BET对催化剂进行了表征。结果表明:硅胶的加入有效地提高了TiO2-SiO2催化剂的热稳定性,抑制了热处理过程中TiO2由锐钛矿相向金红石相的转变和晶粒的长大。随着焙烧温度和TiO2含量的增加,TiO2的晶粒变大,但比表面积减少。TiO2-SiO2的光催化活性明显改善,可见光照射120min,31%TiO2/SiO2催化剂存在下,有84%亚甲基蓝光催化降解。31%TiO2/SiO2催化剂光降解亚甲基蓝的能力大大优于Degussa P-25和纯TiO2,其降解亚甲基蓝的反应速率常数分别为P-25和纯TiO2的8倍和10倍。     

TiO2纳米晶光催化降解铬酸根离子的研究

以二氧化钛为光催化剂,研究了溶液的ｐＨ值、铬酸根离子的初始浓度、通入的气体种类、氧化钛的载量等因素对铬酸根离子降解率的影响。同时合成了粒径小于１０ｎｍ的锐钛矿相和金红石相氧化钛纳米晶来考察晶相和尺寸效应对降解率的影响。结果表明,锐钛矿的催化活性高于金红石相,两者的催化活性均大大高于市售的氧化钛微粉。     

Synthesis of conductive rutile-phased Nb0.06Ti0.94O2 and its supported Pt electrocatalysts (Pt/Nb0.06Ti0.94O2) for the oxygen reduction reaction

In this paper, Nb-doped TiO(2) with anatase and rutile phases was synthesized by the acid-catalyzed sol-gel method, and used as catalyst supports for the oxygen reduction reaction (ORR). X-ray diffraction (XRD), transmission electron microscopy (TEM), Energy dispersive X-ray spectroscopy (EDX), and Brunauer-Emmett-Teller (BET) were used to characterize the support materials in terms of material structures, morphology, composition, and surface area. XRD analysis showed that both the high concentration of hydrochloric acid present in the synthesis and the presence of Pt in the support could favor the formation of conductive rutile phased TiO(2), resulting in the improvement of electronic conduction of the Nb-doped TiO(2) support, which was confirmed by measured conductivities. For electrochemical characterization and ORR catalyst activity validation, Pt particles were deposited on the supports synthesized in this paper to form several catalysts, which were tested for electrochemical Pt surface area, ORR mass activity and specific activity. A monotonic increase in Pt ORR mass activity with increasing catalyst support's conductivity suggested that the support conductivity plays an important role in enhancing catalyst mass activity. The results showed that these non-carbon supported catalysts are promising as PEM fuel cell cathode catalysts.     

Electronic coupling in iron oxide-modified TiO2 leads to a reduced band gap and charge separation for visible light active photocatalysis

In recent experiments Tada et al. have shown that TiO(2) surfaces modified with iron oxide display visible light photocatalytic activity. This paper presents first principles simulations of iron oxide clusters adsorbed at the rutile TiO(2) (110) surface to elucidate the origin of the visible light photocatalytic activity of iron oxide modified TiO(2). Small iron oxide clusters adsorb at rutile (110) surface and their presence shifts the valence band so that the band gap of the composite is narrowed towards the visible, thus confirming the origin of the visible light activity of this composite material. The presence of iron oxide at the TiO(2) surface leads to charge separation, which is the origin of enhanced photocatalytic efficiency, consistent with experimental photoluminesence and photocurrent data. Surface modification of a metal oxide is thus an interesting route in the development of visible light photocatalytic materials.     

Effect of the rutile content on the photovoltaic performance of the dye-sensitized solar cells composed of mixed-phase TiO2 photoelectrodes

The effect of the rutile content on the photovoltaic performance of dye-sensitized solar cells (DSSCs) composed of mixed-phase TiO(2) photoelectrode has been investigated. The mixed-phase TiO(2) particles with varied amounts of rutile, relative to anatase phase, are synthesized by an in situ method where the concentration of sulfate ion is used as a phase-controlling parameter in the formation of TiO(2) using TiCl(4) hydrolysis. The surface area (S(BET)) varies from 33 (pure rutile) to 165 (pure anatase) m(2) g(-1). Generally, both the current density (J(sc)) and photo-conversion efficiency (η) decrease as the rutile content increases. The incorporation of rod-shaped rutile particles causes low uptake of dye due to the reduced surface area, as well as slow electron transport in less efficiently-stacked structure. However, maximum J(sc) (14.63 mA cm(-2)) and η (8.69%) appear when relatively low rutile content (16%) is employed. The reported synergistic effect by the efficient interparticle electron transport from rutile to anatase seems to overbalance the decrease of surface area when small amount of rutile particles is incorporated.     

Ag@AgCl修饰TiO2-xCx光催化剂的制备及其可见光降解污染物性能

以钛酸丁酯和葡萄糖为原料用水热法制备了碳掺杂二氧化钛,再进一步对其进行Ag@AgCl表面修饰.用X射线衍射(XRD),X射线光电子能谱(XPS),透射电镜(TEM),BET比表面仪和紫外-可见(UV-Vis)漫反射光谱等手段对样品进行测试表征;在可见光辐射下(λ＞420 nm),以甲基橙和苯酚溶液的光催化降解实验来评价样品的活性.结果表明:经Ag@AgCl修饰后,样品的粒径增大,比表面积减小,对可见光的响应增强;可见光光催化效率有大幅度提高,对甲基橙和苯酚的降解效率分别是修饰前的5.5和3.4倍,且光催化剂经三次循环使用后活性基本保持不变.     

Photochemical preparation of poly(N-vinyl-2-pyrrolidone)-stabilized platinum colloids and their deposition on titanium dioxide

Preparation processes for Pt-deposited TiO(2) (Pt/TiO(2)) by the synthesis of Pt nanoparticles and their deposition were pursued by transmission electron microscopy, extended X-ray absorption fine structure, UV-vis spectroscopy, and Fourier transform infrared spectroscopic studies. Colloidal dispersions of Pt particles stabilized by poly(N-vinyl-2-pyrrolidone) (PVP) were photochemically synthesized in aqueous ethanol solution. The average diameter of Pt particles was estimated to be 2.0 +/- 0.5 nm, which was almost unchanged by changing the reducing agent from ethanol to methanol and 2-propanol. The PVP-stabilized Pt particles were distributed over a TiO(2) surface only by mixing the Pt colloidal dispersions and TiO(2). CO was chemically coordinated on the Pt particles on a TiO(2) surface after heat treatment was carried out in an O(2) flow at 673 K to completely remove the residual PVP on Pt/TiO(2). Hydrogen reduction at 473 K did not increase the amount of CO adsorbed on Pt sites. The Pt/TiO(2) catalyst after the oxidation treatment showed higher activity for CO photooxidation than that obtained for pure TiO(2) catalyst. The CO photooxidation rate was not unchanged by the H(2) reduction.     

氮-硫共掺杂二氧化钛光催化剂的制备及其可见光催化活性

采用研磨煅烧法,以硫脲(TU)作为氮源和硫源,H2TiO3(HT)为TiO2的前驱体,制备了不同TU/HT比例的N,S共掺杂TiO2光催化剂(NS/TiO2);利用X射线衍射仪、透射电镜、X射线光电子能谱仪、拉曼光谱仪、紫外-可见吸收光谱仪等分析了NS/TiO2的晶体结构、显微形貌、典型元素的化学状态以及光谱性质;利用BET法测定了NS/TiO2的比表面积,同时测定了其在可见光照下催化降解罗丹明B的活性.结果表明,当TU/HT质量比为0.5时,NS/TiO2的光催化活性最佳,光照70min时的罗丹明B降解率为44.4%.氮元素以NH3形式吸附在TiO2表面,硫元素以S6+形式存在,部分S6+取代Ti 4+的位置.与此同时N,S共掺杂使得TiO2的禁带宽度减小,可见光催化活性提高.     

Local work function of Pt clusters vacuum-deposited on a TiO2 surface

Surface topography and work function maps were simultaneously obtained for Pt-evaporated titanium dioxide (TiO(2)) surfaces by using a Kelvin probe force microscope (KPFM). Platinum clusters with diameters of 2-3 nm and heights of 0.2-0.4 nm were obtained on rutile TiO(2)(110)-(1 x 1) surfaces. The work function on the Pt clusters was smaller than that on the surrounding TiO(2) surface. With the assumption that the work function was perturbed by electric dipole moments created at the Pt-TiO(2) interface, the work function decrease indicates that dipole moments were created at the interface and directed toward the vacuum. Such dipole moments can be formed by electron transfer from the originally neutral Pt atoms to the Ti cations exposed on the (1 x 1) surface. A simple model is constructed by assuming a uniform dipole moment per unit interface area. Using this model, the size-dependent perturbation of the work function can be interpreted. The electrostatic potential is more perturbed above the Pt clusters with a larger interface area since the number density of dipole moments is equal to that of the Ti cations and is uniform. A similar correlation between the work function decrease and interface area was observed for the clusters formed on terraces and on step edges. The work function maps showed no peculiar contribution for Ti atoms exposed at the step edges. Vacuum annealing caused a considerable change in the work function on the clusters. The work function was decreased on some clusters relative to the TiO(2) substrate, while it increased on the other clusters. The atomistic structure of the interface may be modified upon annealing, thus perturbing the electron transfer across the interface.     

Microwave-solvothermal synthesis of various polymorphs of nanostructured TiO2 in different alcohol media and their lithium ion storage properties

The various polymorphs (anatase, rutile, and brookite) of TiO(2) with different nanomorphologies have been synthesized by a facile microwave-assisted solvothermal process without surfactants, employing TiCl(4) or TiCl(3) as precursors in various alcohol (ethanol, propanol, butanol, and octanol) media. The samples have been characterized by X-ray diffraction (XRD), electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis. The Ti/Cl ion concentration, reaction pH, and size of the alcohol molecule are found to control the morphology, crystal structure, and crystallite size of the TiO(2) particles. Among the various TiO(2) polymorphs synthesized, the rutile TiO(2) spheres built up of nanorods that were synthesized with TiCl(4) in octanol have an average pore size and surface area of, respectively, 5 nm and 404 m(2)/g and exhibit the best electrochemical performance with a capacity of >200 mAh/g after 100 cycles and high rate capability. The excellent electrochemical properties originate from the nanorod-building morphology and mesoporosity of TiO(2) spheres that provide good electrical contact, accommodates the strain smoothly, and facilitates facile lithium-ion diffusion.     

SiO2负载的TiO2光催化剂可见光催化降解染料污染物

 采用酸催化溶胶-凝胶法制备了SiO2负载的TiO2光催化剂,考察了制备条件对负载型TiO2光催化剂的晶相、结构、比表面积和可见光催化活性的影响. 结果表明,采用SiO2为载体时,TiO2以纳米颗粒的形态分散在载体表面,负载型TiO2/SiO2催化剂的比表面积大、等电点低而且热稳定性能良好. 偶氮染料酸性橙7的可见光催化降解实验结果表明,染料污染物在催化剂表面的吸附是影响催化剂可见光催化活性的重要因素. 与试剂TiO2样品相比,负载型TiO2/SiO2光催化剂具有更好的光催化活性和沉降性能.     

Pt、N共掺杂TiO2在可见光下对三氯乙酸的催化降解作用

采用溶胶-凝胶法制备了氮掺杂纳米TiO₂(N-TiO₂), 并用光分解沉积法在N-TiO₂表面负载微量金属Pt(0.5％(w)), 形成铂-氮共掺杂纳米TiO₂(Pt/N-TiO₂). 实验结果表明, Pt 、N共掺杂纳米TiO₂紫外可见光吸收边带较纳米TiO₂红移约20 nm, 并在400～500 nm处有弱的吸收. Pt/N-TiO₂电极在可见光区的光电流约为纳米TiO₂电极的6倍. 以Pt/N-TiO₂为催化剂, 催化三氯乙酸(TCA)光降解反应, 室温下经可见光照射2 h后TCA降解率约为8％. N掺杂减小了TiO₂的禁带能隙, 使它在可见光区具有光催化活性, 适量Pt掺杂抑制了光生载流子的复合, 加速了电子界面传递速度, Pt、N共掺杂使两种效应相结合, 进一步提高了光催化反应性能.     

Preparation and enhanced visible-light photocatalytic H2-production activity of CdS-sensitized Pt/TiO2 nanosheets with exposed (001) facets

CdS-sensitized Pt/TiO(2) nanosheets with exposed (001) facets were prepared by hydrothermal treatment of a Ti(OC(4)H(9))(4)-HF-H(2)O mixed solution followed by photochemical reduction deposition of Pt nanoparticles (NPs) on TiO(2) nanosheets (TiO(2) NSs) and chemical bath deposition of CdS NPs on Pt/TiO(2) NSs, successively. The UV and visible-light driven photocatalytic activity of the as-prepared samples was evaluated by photocatalytic H(2) production from lactic acid aqueous solution under UV and visible-light (λ ≥ 420 nm) irradiation. It was shown that no photocatalytic H(2)-production activity was observed on the pure TiO(2) NSs under UV and/or visible-light irradiation. Deposition of CdS NPs on Pt/TiO(2) NSs caused significant enhancement of the UV and visible-light photocatalytic H(2)-production rates. The morphology of TiO(2) particles had also significant influence on the visible-light H(2)-production activity. Among TiO(2) NSs, P25 and the NPs studied, the CdS-sensitized Pt/TiO(2) NSs show the highest photocatalytic activity (13.9% apparent quantum efficiency obtained at 420 nm), exceeding that of CdS-sensitized Pt/P25 by 10.3% and that of Pt/NPs by 1.21%, which can be attributed to the combined effect of several factors including the presence of exposed (001) facets, surface fluorination and high specific surface area. After many replication experiments of the photocatalytic hydrogen production in the presence of lactic acid, the CdS-sensitized Pt/TiO(2) NSs did not show great loss in the photocatalytic activity, confirming that the CdS/Pt/TiO(2) NSs system is stable and not photocorroded.     

Synthesis, characterization, and visible light activity of new nanoparticle photocatalysts based on silver, carbon, and sulfur-doped TiO2

New nanoparticle photocatalysts based on silver, carbon, and sulfur-doped TiO2 having only the homogeneous anatase crystalline phase and high surface area were successfully synthesized by a modified sol-gel route. The catalysts were characterized by EDX, XRD, BET, UV-vis, IR, and Raman spectroscopy. The effects of the experimental parameters on the visible light reactivity of the catalysts were evaluated for the photodegradation of gaseous acetaldehyde as a model indoor pollutant. The activity results show that the silver(I) ion, Ag(+), doping significantly promotes the visible light reactivities of carbon and sulfur-doped TiO2 catalysts without any phase transformation from anatase to rutile. Moreover, Ag/(C, S)-TiO2 photocatalysts degrade acetaldehyde 10 times faster in visible light and 3 times faster in UV light illuminations than the accredited photocatalyst P25-TiO2. The commendable visible photoactivities of Ag/(C, S)-TiO2 new nanoparticle photocatalysts are predominantly attributable to an improvement in anatase crystallinity, high surface area, low band gap and nature of precursor materials used.     

Synergic effect of simultaneous fluorination and platinization of TiO2 surface on anoxic photocatalytic degradation of organic compounds

Simultaneously surface fluorinated and platinized TiO2 (F-TiO2/Pt) exhibits a novel photocatalytic activity for the anoxic degradation of organic compounds, which is attributed to the unique synergic effect of surface fluorination and platinization on the photo-induced charge transfer process.     

Mesoporous TiO2 nanostructures: a route to minimize Pt loading on titania photocatalysts for hydrogen production

Mesostructured TiO(2) nanocrystals have been prepared using Pluronic F127 as the structure-directing agent. Platinum nanoparticles at different contents (0.1-1.0 wt%) have been photochemically deposited onto the mesoporous TiO(2). TEM investigation of 0.2 wt% Pt/TiO(2) calcined at 450 °C reveals that the TiO(2) particles are quite uniform in size and shape with the particle sizes of TiO(2) and Pt being 10 and 3 nm, respectively. The photocatalytic activities of the Pt loaded TiO(2) have been assessed and compared with those of nonporous commercial Pt/TiO(2)-P25 by determining the rates and the photonic efficiencies of molecular hydrogen production from aqueous methanol solutions. The results show that the amount of hydrogen evolved on Pt/TiO(2)-450 at low Pt loading (0.2 wt%) is three times higher than that evolved on Pt/TiO(2)-P25 and twelve times higher than that evolved on Pt/TiO(2)-350. Despite the BET surface area of the TiO(2)-450 photocatalyst being 3.5 times higher than that of TiO(2)-P25, a 60% smaller amount of the Pt co-catalyst is required to obtain the optimum photocatalytic hydrogen production activity. The reduced Pt loading on the mesoporous TiO(2) will be important both from a commercial and an ecological point of view.     

Unpredictable adsorption and visible light induced decolorization of nano rutile for the treatment of crystal violet

Photocatalysts containing different ratios of anatase and rutile are prepared via heat treatment of Degussa P-25 titania. X-ray diffraction (XRD), Bruuauer-Emmett-Teller (BET), ultraviolet–visible light diffuse reflectance spectra (DRS), Raman spectra (Raman), positron annihilation lifetime spectra (PAL) and temperature-programmed desorption (TPD) are applied to investigate the phase composition of the synthesized catalysts. Using crystal violet (CV) as the target pollutant, the unexpected visible light decolorization of rutile is observed. Despite the decreased specific surface area, the as-synthesized rutile samples exhibit much higher adsorption capability of CV than P-25 does, which in turn leads to improved photoreaction efficiency. Since the rutile samples can't absorb the visible light, the degradation under visible light irradiation is attributed to self-sensitization of CV on the surface of rutile.     

Synthesis of highly active sulfate-promoted rutile titania nanoparticles with a response to visible light

Highly active sulfate-promoted rutile titania (SO(4)(2-)/TiO(2)) with smaller band gap was prepared by an in situ sulfation method, that is, under moderate conditions, sulfate-promoted rutile titania was directly obtained via precipitating Ti(SO(4))(2) in NaOH solution followed by peptizing in HNO(3) without the phase transformation from anatase to rutile. Thus, the negative impacts of phase transformation from anatase to rutile on the structure, surface, and photoactivity properties of the catalysts due to higher calcination temperature can be avoided. The catalysts were characterized by means of thermal analysis, Brunauer-Emmett-Teller analysis (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), UV-visible spectroscopy, FT-IR pyridine adsorption, and temperature-programmed desorption (TPD). The results show sulfate species are sensitive to the variation of calcination temperature. In the process of peptizing, sulfate species are homogeneously dispersed throughout the bulk of catalysts, allowing sulfate species to penetrate into the network of TiO(2) effectively. After being calcined at 300 degrees C, sulfate species occupy oxygen sites to form Ti-S bonds, as evidenced by XPS results. As calcination temperature is further increased to 600 degrees C or above, the active sulfate species on the catalyst surface are destroyed, and the sulfate species in the network of TiO(2) are expelled out onto the surface to form inactive sulfate species. Thus, Ti(3+) defects will be produced on the catalyst surface. Accompanying this process, surface area is decreased promptly, and crystalline size is greatly increased via two fast growth phases due to the decomposition of sulfate species with different binding forces. Most importantly, the band gap of SO(4)(2-)/TiO(2) is remarkably shifted to the visible light region due to the formation of Ti-S bonds, and with increasing calcination temperature the visible light absorption capability is reduced due to breakage of Ti-S bonds. The excellent photoactivity of 300 degrees C calcined SO(4)(2-)/TiO(2) can be explained by its small crystalline size, high surface area, loose and porous microstructure, and the generation of Br?nsted acidity on its surface.     

Effect of TiO2 crystalline phase composition on the physicochemical and catalytic properties of Pd/TiO(2) in selective acetylene hydrogenation

Pd/TiO(2) catalysts have been prepared using TiO(2) supports consisting of various rutile/anatase crystalline phase compositions. Increasing percentages of rutile phase in the TiO(2) resulted in a decrease in Brunauer-Emmett-Teller surface areas, fewer Ti(3+) sites, and lower Pd dispersion. While acetylene conversions were found to be merely dependent on Pd dispersion, ethylene selectivity appeared to be strongly affected by the presence of Ti(3+) in the TiO(2) samples. When TiO(2) samples with 0-44% rutile were used, high ethylene selectivities (58-93%) were obtained whereas ethylene losses occurred for those supported on TiO(2) with 85% or 100% rutile phase. X-ray photoelectron spectroscopy and electron spin resonance experiments revealed that a significant amount of Ti(3+) existed in the TiO(2) samples composed of 0-44% rutile. The presence of Ti(3+) in contact with Pd can probably lower the adsorption strength of ethylene resulting in an ethylene gain. Among the five catalysts used in this study, the results for Pd/TiO(2)-R44 suggest an optimum anatase/rutile composition of the TiO(2) used to obtain high selectivity of ethylene in selective acetylene hydrogenation.