Polymer-Supported Liquid Layer Electrolyzer Enabled Electrochemical CO2 Reduction to CO with High Energy Efficiency

The electrochemical conversion of carbon dioxide (CO₂) to carbon monoxide (CO) is a favorable approach to reduce CO₂ emission while converting excess sustainable energy to important chemical feedstocks. At high current density (>100 mA cm⁻²), low energy efficiency (EE) and unaffordable cell cost limit the industrial application of conventional CO₂ electrolyzers. Thus, a crucial and urgent task is to design a new type of CO₂ electrolyzer that can work efficiently at high current density. Here we report a polymer-supported liquid layer (PSL) electrolyzer using polypropylene non-woven fabric as a separator between anode and cathode. Ag based cathode was fed with humid CO₂ and potassium hydroxide was fed to earth-abundant NiFe-based anode. In this configuration, the PSL provided high-pH condition for the cathode reaction and reduced the cell resistance, achieving a high full cell EE over 66 % at 100 mA cm⁻².     

High-Curvature Transition-Metal Chalcogenide Nanostructures with a Pronounced Proximity Effect Enable Fast and Selective CO2 Electroreduction

A considerable challenge in the conversion of carbon dioxide into useful fuels comes from the activation of CO₂ to CO₂^.− or other intermediates, which often requires precious-metal catalysts, high overpotentials, and/or electrolyte additives (e.g., ionic liquids). We report a microwave heating strategy for synthesizing a transition-metal chalcogenide nanostructure that efficiently catalyzes CO₂ electroreduction to carbon monoxide (CO). We found that the cadmium sulfide (CdS) nanoneedle arrays exhibit an unprecedented current density of 212 mA cm⁻² with 95.5±4.0 % CO Faraday efficiency at −1.2 V versus a reversible hydrogen electrode (RHE; without iR correction). Experimental and computational studies show that the high-curvature CdS nanostructured catalyst has a pronounced proximity effect which gives rise to large electric field enhancement, which can concentrate alkali-metal cations resulting in the enhanced CO₂ electroreduction efficiency.     

Catalytic Reduction of CN−, CO,and CO2 by Nitrogenase Cofactors in Lanthanide‐Driven Reactions

Nitrogenase cofactors can be extracted into an organic solvent to catalyze the reduction of cyanide (CN⁻), carbon monoxide (CO), and carbon dioxide (CO₂) without using adenosine triphosphate (ATP), when samarium(II) iodide (SmI₂) and 2,6‐lutidinium triflate (Lut‐H) are employed as a reductant and a proton source, respectively. Driven by SmI₂, the cofactors catalytically reduce CN⁻ or CO to C₁–C₄ hydrocarbons, and CO₂ to CO and C₁–C₃ hydrocarbons. The C C coupling from CO₂ indicates a unique Fischer–Tropsch‐like reaction with an atypical carbonaceous substrate, whereas the catalytic turnover of CN⁻, CO, and CO₂ by isolated cofactors suggests the possibility to develop nitrogenase‐based electrocatalysts for the production of hydrocarbons from these carbon‐containing compounds.     

Iron Porphyrin Allows Fast and Selective Electrocatalytic Conversion of CO2 to CO in a Flow Cell

Molecular catalysts have been shown to have high selectivity for CO₂ electrochemical reduction to CO, but with current densities significantly below those obtained with solid-state materials. By depositing a simple Fe porphyrin mixed with carbon black onto a carbon paper support, it was possible to obtain a catalytic material that could be used in a flow cell for fast and selective conversion of CO₂ to CO. At neutral pH (7.3) a current density as high as 83.7 mA cm⁻² was obtained with a CO selectivity close to 98 %. In basic solution (pH 14), a current density of 27 mA cm⁻² was maintained for 24 h with 99.7 % selectivity for CO at only 50 mV overpotential, leading to a record energy efficiency of 71 %. In addition, a current density for CO production as high as 152 mA cm⁻² (>98 % selectivity) was obtained at a low overpotential of 470 mV, outperforming state-of-the-art noble metal based catalysts.     

Experimental Evidence of CO2 Photoreduction Activity of SnO2 Nanoparticles

Tin dioxide (SnO₂) has intrinsic characteristics that do not favor its photocatalytic activity. However, we evidenced that surface modification can positively influence its performance for CO₂ photoreduction in the gas phase. The hydroxylation of the SnO₂ surface played a role in the CO₂ affinity decreasing its reduction potential. The results showed that a certain selectivity for methane (CH₄), carbon monoxide (CO), and ethylene (C₂H₄) is related to different SnO₂ hydrothermal annealing. The best performance was seen for SnO₂ annealed at 150 °C, with a production of 20.4 μmol g⁻¹ for CH₄ and 16.45 μmol g⁻¹ for CO, while for SnO₂ at 200 °C the system produced more C₂H₄, probably due to a decrease of surface −OH groups.     

Utilization of standards generated in the process of thermal decomposition chemically modified silica gel for a single point calibration of a GC/FID system

The utilization of a multicomponent gaseous standard mixture, containing CO and CO(2) and obtained by thermal decomposition of a so-called immobilized compound, for a single point calibration of a GC/FID system are described. The generation of such a mixture takes place as a result of thermal decomposition of a sample of chemically modified silica gel placed in a heated chamber of thermal desorber coupled with the device being calibrated via a catalytic methanizer. The mean amount of the analyte librated from unit mass of the gel was 0.71 mg g(-1) (RSD = 3%) for carbon monoxide and 0.86 mg g(-1) (RSD = 3%) for carbon dioxide.     

Molecular Modification of Single Cobalt Sites Boosts the Catalytic Activity of CO2 Electroreduction into CO

Electroreduction of CO₂ into carbonaceous fuels or industrial chemicals using renewable energy sources is an ideal way to promote global carbon recycling. Thus, it is of great importance to develop highly selective, efficient, and stable catalysts. Herein, we prepared cobalt single atoms (Co SAs) coordinated with phthalocyanine (Co SAs-Pc). The anchoring of phthalocyanine with Co sites enabled electron transfer from Co sites to CO₂ effectively via the π-conjugated system, resulting in high catalytic performance of CO₂ electroreduction into CO. During the process of CO₂ electroreduction, the Faradaic efficiency (FE) of Co SAs-Pc for CO was as high as 94.8 %. Meanwhile, the partial current density of Co SAs-Pc for CO was −11.3 mA cm⁻² at −0.8 V versus the reversible hydrogen electrode (vs RHE), 18.83 and 2.86 times greater than those of Co SAs (−0.60 mA cm⁻²) and commercial Co phthalocyanine (−3.95 mA cm⁻²), respectively. In an H-cell system operating at −0.8 V vs RHE over 10 h, the current density and FE for CO of Co SAs-Pc dropped by 3.2 % and 2.5 %. A mechanistic study revealed that the promoted catalytic performance of Co SAs-Pc could be attributed to the accelerated reaction kinetics and facilitated CO₂ activation.     

Kinetics and mechanism of the Cl + CO reaction in air

Long-path FTIR spectroscopy was used to study the kinetics and mechanism of the reaction of Cl atoms with CO in air. The relative rate constants at 298 K and 760 torr for the forward direction of the reaction of Cl with ¹³CO and the reaction of Cl¹³CO with O₂ were k₁ = (3.4 ± 0.8) × 10⁻¹⁴ cm³ molecule⁻¹ s⁻¹ and k₂ = (4.3 ± 3.2) × 10⁻¹³ cm³ molecule⁻¹ s⁻¹, respectively (all uncertainty limits are 2σ). The rate constant for the net loss of ¹³CO due to reaction with Cl in 1 atm of air at 298 K was k_Cl+COobs = (3.0 ± 0.6) × 10⁻¹⁴ cm³ molecule⁻¹ s⁻¹. The only observed carbon-containing product of the Cl + ¹²CO reaction was ¹²CO₂, with a yield of 109 ± 18%. Our results are in good agreement with extrapolations from previous studies. The reaction mechanism and the implications for laboratory studies and tropospheric chemistry are discussed. © 1996 John Wiley & Sons, Inc.     

Catalytic Reduction of CN−, CO,and CO2 by Nitrogenase Cofactors in Lanthanide‐Driven Reactions

Nitrogenase cofactors can be extracted into an organic solvent to catalyze the reduction of cyanide (CN^?), carbon monoxide (CO), and carbon dioxide (CO₂) without using adenosine triphosphate (ATP), when samarium(II) iodide (SmI₂) and 2,6‐lutidinium triflate (Lut‐H) are employed as a reductant and a proton source, respectively. Driven by SmI₂, the cofactors catalytically reduce CN^? or CO to C₁–C₄ hydrocarbons, and CO₂ to CO and C₁–C₃ hydrocarbons. The C? C coupling from CO₂ indicates a unique Fischer–Tropsch‐like reaction with an atypical carbonaceous substrate, whereas the catalytic turnover of CN^?, CO, and CO₂ by isolated cofactors suggests the possibility to develop nitrogenase‐based electrocatalysts for the production of hydrocarbons from these carbon‐containing compounds.     

Enhanced Electrocatalytic Activity of a Zinc Porphyrin for CO2 Reduction: Cooperative Effects of Triazole Units in the Second Coordination Sphere

The control of the second coordination sphere in a coordination complex plays an important role in improving catalytic efficiency. Herein, we report a zinc porphyrin complex ZnPor8T with multiple flexible triazole units comprising the second coordination sphere, as an electrocatalyst for the highly selective electrochemical reduction of carbon dioxide (CO₂) to carbon monoxide (CO). This electrocatalyst converted CO₂ to CO with a Faradaic efficiency of 99 % and a current density of −6.2 mA cm⁻² at −2.4 V vs. Fc/Fc⁺ in N,N-dimethylformamide using water as the proton source. Structure-function relationship studies were carried out on ZnPor8T analogs containing different numbers of triazole units and distinct triazole geometries; these unveiled that the triazole units function cooperatively to stabilize the CO₂-catalyst adduct in order to facilitate intramolecular proton transfer. Our findings demonstrate that incorporating triazole units that function in a cooperative manner is a versatile strategy to enhance the activity of electrocatalytic CO₂ conversion.     

Electrocatalytic Functionalized Specialty Paper as Low-Cost Porous Transport Layer Material in CO2-Electrolysis

The development of low-cost and efficient electrolyzer components is crucial for practical electrochemical carbon dioxide reduction (ECR). In this study, facile non-woven cellulose-based porous transport layers (PTLs) were developed for high current density CO₂-to-CO conversion. By depositing a cobalt phthalocyanine (CoPc) catalyst-layer over the PTLs, we fabricated ECR-functioning gas-diffusion-electrodes (GDEs) for both flow-cell and zero-gap electrolyzers. Under optimal conditions, the Faradaic efficiency of CO (FE_CO) reached 92 % at a high current density of 200 mA cm⁻². Furthering the architecture of the GDEs, CoPc was incorporated into the initial PTL slurry, forming ECR-active PTLs without the need for an additional catalyst-layer. The new GDE-architecture favored the CoPc-distribution by enhancing the contact and interactions with the carbon substrate and demonstrated a stable electrolysis process for over 50 h in a zero-gap cell at 200 mA cm⁻² with a FE_CO of 80 %.     

Boosting CO2 Electroreduction on N,P-Co-doped Carbon Aerogels

Electroreduction of CO₂ to CO powered by renewable electricity is a possible alternative to synthesizing CO from fossil fuel. However, it is very hard to achieve high current density at high faradaic efficiency (FE). Here, the first use of N,P-co-doped carbon aerogels (NPCA) to boost CO₂ reduction to CO is presented. The FE of CO could reach 99.1 % with a partial current density of −143.6 mA cm⁻², which is one of the highest current densities to date. NPCA has higher electrochemical active area and overall electronic conductivity than that of N- or P-doped carbon aerogels, which favors electron transfer from CO₂ to its radical anion or other key intermediates. By control experiments and theoretical calculations, it is found that the pyridinic N was very active for CO₂ reduction to CO, and co-doping of P with N hinder the hydrogen evolution reaction (HER) significantly, and thus the both current density and FE are very high.     

Polymer-silica nanocomposite membranes for CO2 capturing

Reducing carbon dioxide (CO₂) is an area of great interest in current international efforts geared toward lowering emissions and combating global warming. In this work, amino-silica composite membranes were prepared and used to capture carbon dioxide. The surface of silica particles was chemically modified with amine to efficiently capture carbon dioxide. The phase separation technique was used to prepare the membranes from a composite containing polyvinylidene-fluoride-hexafluoropropylene (PVDF-HFP), amino-silica particles, acetone and water. SEM images revealed that the membranes composed of multilayers of porous polymer uniformly impregnated with silica particles. Both XRD and FTIR results have validated the perfect integration of silica particles within the polymeric network. The mechanical properties of the membrane are improved by the presence of silica particles as proved by the high tensile strength value (1.5 N/cm²) obtained for the PVDF-HFP/SiO₂ membrane compared to 0.9 N/cm² obtained for bare PVDF-HFP membrane. Also, we succeeded in recording SEM images to show that the plastic deformation of the film is associated with the formation of macro-holes. To the best of our knowledge this is the first time for such results to be monitored with SEM to observe the macroscopic evolution of the structure. Additionally, the surface area was significantly increased from 3.8 m²/g for bare PVDF-HFP membrane to 116.4 m²/g for PVDF-HFP impregnated with silica particles. Moreover, the CO₂ separation efficiency depends on both surface area and the quantity of amino-SiO₂ added to the membrane. The addition of amino-silica particles leads to a significant uptake of carbon dioxide compared to non-modified polymer membrane. The results obtained indicated that combing the phase separation with amino silica particles provided a cost-effective route to scaling up the synthesis of membranes that were mechanically stable and highly efficient at CO₂ capture.     

CO adsorption on clean and oxidized Al(110)

Electron-energy loss (EELS) spectra and thermal desorption (TDS) traces of carbon monoxide bound to the (100) surface of aluminum are presented. CO chemisorption on clean Al(100) is characterized by vibrational bands at 440 and 2060 cm⁻¹ and by desorption at 125 K. Oxide “islands”, formed by oxidation in O₂ at 575 K, have no observed electronic influence on open metallic areas of the adsorbent but merely block CO adsorption sites.     

High‐Curvature Transition‐Metal Chalcogenide Nanostructures with a Pronounced Proximity Effect Enable Fast and Selective CO2 Electroreduction

A considerable challenge in the conversion of carbon dioxide into useful fuels comes from the activation of CO₂ to CO₂^.? or other intermediates, which often requires precious‐metal catalysts, high overpotentials, and/or electrolyte additives (e.g., ionic liquids). We report a microwave heating strategy for synthesizing a transition‐metal chalcogenide nanostructure that efficiently catalyzes CO₂ electroreduction to carbon monoxide (CO). We found that the cadmium sulfide (CdS) nanoneedle arrays exhibit an unprecedented current density of 212 mA cm^?2 with 95.5±4.0 % CO Faraday efficiency at ?1.2 V versus a reversible hydrogen electrode (RHE; without iR correction). Experimental and computational studies show that the high‐curvature CdS nanostructured catalyst has a pronounced proximity effect which gives rise to large electric field enhancement, which can concentrate alkali‐metal cations resulting in the enhanced CO₂ electroreduction efficiency.     

Heterogeneous recombination of O + CO on solid CO2 at 77 K

Heterogeneous recombination of O + CO → CO₂ over a solid CO₂ surface at 77 K was investigated. A modified discharge flow setup was used to generate low O atom concentrations by the reaction N + NO → N₂ + O(³P). The O atom concentrations were measured upstream and downstream of the solid CO₂ substrate using resonance fluorescence by monitoring the unresolved 130.3 nm triplet transition ³S₁ ? ³P_2,1,0 at the two fixed points. CO₂ formed was determined by measuring the β activity from C¹⁴O₂ produced from CO containing C¹⁴O as a reactant gas. The CO₂ formation was found to be first order in CO and independent of O atom concentration over the entire range of 4.3 × 10¹² to 1.9 × 10¹⁴ cm^?3 and 1.2 × 10¹¹ to 5.6 × 10¹² cm^?3 for CO and O respectively. The first order recombination coefficient, λ_CO was found to be 1.4 (±.38) × 10^?5.     

Vibration—vibration energy exchange between carbon monoxide and carbon dioxide

Measurements have been made on the vibration—vibration (V—V) energy exchange rate between carbon monoxide and carbon dioxide in the temperature range 180 to 345 K. A steady-state vibrational fluorecence quenching technique was used in conjunction with an open flow gas system. Vibrational excitation of the carbon monoxide was accomplished by absorption of infrared radiation from prospane—oxygen flames. The measured rate constant for the process CO* (υ = 1) + CO₂ → CO + CO^*₂(001) increased linearly with temperature, and after correction for the V—V exchange rate fo the back reaction, the rate constant has a value of (2.2 ± 0.3) × 10³ torr^?1 s^?1 at 296 K. The data are compared to results at highest temperatures and to available theoretical calculations.     

Temperature programmed decomposition studies: high-sensitivity determination of carbon monoxide,carbon dioxide and methane by gas chromatography

Carbon monoxide, carbon dioxide and methane, evolved in very low amount during temperature programmed decomposition of transition metal cluster catalysts, can be determined quickly (<3 min) by gas chromatography on a Porapak S column. Catalytic conversion of the CO and CO₂ to methane makes it possible to use a hydrogen fiame ionization detector. The advantages are that the limit of detection is about 1 ppm (ca. 4.4 × 10^?11 mol cm^?3, STP) and that the procedure is applicable to decompositions studied in helium/oxygen or other reactive gas mixtures.     

Highly Efficient CO2 Electroreduction on ZnN4‐based Single‐Atom Catalyst

The electrochemical reduction reaction of carbon dioxide (CO2RR) to carbon monoxide (CO) is the basis for the further synthesis of more complex carbon‐based fuels or attractive feedstock. Single‐atom catalysts have unique electronic and geometric structures with respect to their bulk counterparts, thus exhibiting unexpected catalytic activities. A nitrogen‐anchored Zn single‐atom catalyst is presented for CO formation from CO2RR with high catalytic activity (onset overpotential down to 24 mV), high selectivity (Faradaic efficiency for CO (FE_CO) up to 95 % at ?0.43 V), remarkable durability (>75 h without decay of FE_CO), and large turnover frequency (TOF, up to 9969 h^?1). Further experimental and DFT results indicate that the four‐nitrogen‐anchored Zn single atom (Zn‐N₄) is the main active site for CO2RR with low free energy barrier for the formation of *COOH as the rate‐limiting step.     

Recombination of carbon monoxide and oxygen atoms

The recombination of carbon monoxide and oxygen atoms was studied in reflected shock waves in H₂:O₂:CO:Ar = 0.1:1:24:75 with 1300 < T₅ 2200 K and 2 < P₅ < 4 atm. Reaction progress was monitored by observations of the carbon monoxide flame spectrum near 435 nm and carbon dioxide thermal emission near 4.2 μm. Data analysis was accomplished with the aid of computer modeling using a 27-reaction mechanism. Computer modeling experiments also showed that these measurements were sensitive primarily to the rate of the reaction CO + O + M = CO₂ + M and only slightly sensitive to the rates of other reactions. The best fit to the data was achieved with a rate constant for this reaction of 7.7 × 10^?35 exp[19 kJ/RT] cm⁶ s for the temperature range of these experiments. Correlation of this result and previous data covering the temperature range 250 < T < 11,000 K confirms that this recombination reaction is governed by a nonadiabatic curve crossing with an activation barrier of about 20 kJ and subsequent deactivation of a singlet CO₂ molecule.