Simultaneous Element-Selective Detection of C,F, Cl,Br, and I by Capillary Gas Chromatography Coupled with Microplasma Mass Spectrometry

Simultaneous element-selective detection of the halogens and carbon was accomplished with capillary gas chromatography coupled with microplasma mass spectrometry. The microplasma ion source was a radio frequency plasma contained inside the last 4–5 cm of the 0.32 mm i.d. fused silica capillary column. The ion source was located inside the high vacuum housing of the MS, and only the GC carrier gas (2.3 mL min⁻¹ of helium) was used for plasma generation. Atomic ions were detected in the positive mode. Detection limits were in the low picogram area, and the selectivity to carbon ranged from 8×10² for fluorine to higher than 10⁴ for the other halogens. By introduction of both hydrogen and oxygen as reagent gases, peak tailing was avoided by suppression of analyte reactions with the silica walls of the ion source. Special attention was given to the fluorine-selective detection due to an interfering background species at m/z 19, assumed to be H₃O⁺ originating from the reagent gases. The background signal was minimized by careful control of the power level.     

Capillary gas chromatography coupled with microplasma mass spectrometry for organotin speciation.

Gas chromatography was coupled with microplasma mass spectrometry for selective detection of organotin compounds. The microplasma ion source was a capacitively coupled radiofrequency helium plasma, which was located inside the high vacuum area of the mass spectrometer. Only 1-3 ml min-1 of helium carrier gas from the gas chromatograph was necessary for sustaining the plasma while 0.15-1.5 ml min-1 of hydrogen was added as reagent gas. Hydrogen was applied for prevention of carbon deposition and served to minimize the interactions between tin and the fused-silica inner surface of the microplasma ion source. Both carbon and tin were detected as positively charged atomic ions, which were expelled from the microplasma ion source and directly focused by electrostatic lenses towards the quadrupole mass analyzer. Tin exhibited high selectivity to carbon (> 10(4)) and a detection limit of 3.5 pg s-1.     

Sterically hindered phenols in negative ion mobility spectrometry–mass spectrometry

Negative corona discharge atmospheric pressure chemical ionization (APCI) was used to investigate phenols with varying numbers of tert‐butyl groups using ion mobility spectrometry–mass spectrometry (IMS‐MS). The main characteristic ion observed for all the phenolic compounds was the deprotonated molecule [M–H]⁻. 2‐tert‐Butylphenol showed one main mobility peak in the mass‐selected mobility spectrum of the [M–H]⁻ ion measured under nitrogen atmosphere. When air was used as a nebulizer gas an oxygen addition ion was seen in the mass spectrum and, interestingly, this new species [M–H+O]⁻ had a shorter drift time than the lighter [M–H]⁻ ion. Other phenolic compounds primarily produced two IMS peaks in the mass‐selected mobility spectra measured using the [M–H]⁻ ion. It was also observed that two isomeric compounds, 2,4‐di‐tert‐butylphenol and 2,6‐di‐tert‐butylphenol, could be separated with IMS. In addition, mobilities of various characteristic ions of 2,4,6‐trinitrotoluene were measured, since this compound was previously used as a mobility standard. The possibility of using phenolic compounds as mobility standards is also discussed. Copyright © 2009 John Wiley & Sons, Ltd.     

Study of Gaseous Sample Ionization by Excited Particles Formed in Glow Discharge Using High-Resolution Orthogonal Acceleration Time-of-Flight Mass Spectrometer

The experimental results of a mass spectral analysis of volatile organic compounds in a gaseous sample, obtained using an original design of an ion source based on the Penning ionization of a gas sample by excited metastable inert gas atoms, are presented. Using ANSYS software, a gas-dynamic simulation of reagent gas flow from discharge zone to ionization region was carried out to analyze the effect of gas flow profile on the transport of metastable atoms and ionization efficiency. The n-octane and toluene samples diluted with helium at 100 ppb mole concentrations were used for our experiments. The resulting mass spectra of n-octane and toluene samples containe far more intensive molecular ions in comparison to n-octane and toluene electron ionization mass spectra from the NIST database. The sensitivity of 5 ions per 1 pg and 130 ions per 1 pg was achieved for n-octane and toluene molecular ions using the developed ion source combined with our mass spectrometer. The corresponding detection limits are 2.3 pg s^–1 for n-octane molecular ions and 0.08 pg s^–1 for toluene molecular ions. The detection limit for the reported ion source was considered theoretically.     

Quantification and remote detection of nitro explosives by helium plasma ionization mass spectrometry (HePI‐MS) on a modified atmospheric pressure source designed for electrospray ionization

Helium Plasma Ionization (HePI) generates gaseous negative ions upon exposure of vapors emanating from organic nitro compounds. A simple adaptation converts any electrospray ionization source to a HePI source by passing helium through the sample delivery metal capillary held at a negative potential. Compared with the demands of other He‐requiring ambient pressure ionization sources, the consumption of helium by the HePI source is minimal (20–30 ml/min). Quantification experiments conducted by exposing solid deposits to a HePI source revealed that 1 ng of 2,4,6‐trinitrotoluene (TNT) on a filter paper (about 0.01 ng/mm²) could be detected by this method. When vapor emanating from a 1,3,5‐trinitroperhydro‐1,3,5‐triazine (RDX) sample was subjected to helium plasma ionization mass spectrometry (HePI‐MS), a peak was observed at m/z 268 for (RDX●NO₂)^?. This facile formation of NO₂^? adducts was noted without the need of any extra additives as dopants. Quantitative evaluations showed RDX detection by HePI‐MS to be linear over at least three orders of magnitude. TNT samples placed even 5 m away from the source were detected when the sample headspace vapor was swept by a stream of argon or nitrogen and delivered to the helium plasma ion source via a metal tube. Among the tubing materials investigated, stainless steel showed the best performance for sample delivery. A system with a copper tube, and air as the carrier gas, for example, failed to deliver any detectable amount of TNT to the source. In fact, passing over hot copper appears to be a practical way of removing TNT or other nitroaromatics from ambient air. Copyright © 2012 John Wiley & Sons, Ltd.     

An LC–MS/MS method for rapid and sensitive high‐throughput simultaneous determination of various protein kinase inhibitors in human plasma

A reliable, high‐throughput and sensitive LC–MS/MS procedure was developed and validated for the determination of five tyrosine kinase inhibitors in human plasma. Following their extraction from human plasma, samples were eluted on a RP Luna®‐PFP 100 Å column using a mobile phase system composed of acetonitrile and 0.01 m ammonium formate in water (pH ~4.1) with a ratio of (50:50, v /v) flowing at 0.3 mL min⁻¹. The mass spectrometer was operating with electrospray ionization in the positive ion multiple reaction monitoring mode. The proposed methodology resulted in linear calibration plots with correlation coefficients values of r ² = 0.9995–0.9999 from concentration ranges of 2.5–100 ng mL⁻¹ for imatinib, 5.0–100 ng mL⁻¹ for sorafenib, tofacitinib and afatinib, and 1.0–100 ng mL⁻¹ for cabozantinib. The procedure was validated in terms of its specificity, limit of detection (0.32–1.71 ng mL⁻¹), lower limit of quantification (0.97–5.07 ng mL⁻¹), intra‐ and inter assay accuracy (−3.83 to +2.40%) and precision (<3.37%), matrix effect and recovery and stability. Our results demonstrated that the proposed method is highly reliable for routine quantification of the investigated tyrosine kinase inhibitors in human plasma and can be efficiently applied in the rapid and sensitive analysis of their clinical samples.     

LC–MS Simultaneous Determination of Itopride Hydrochloride and Domperidone in Human Plasma

A rapid, simple, sensitive and specific liquid chromatography–tandem mass spectrometry method was developed and validated for simultaneous quantification of itopride hydrochloride and domperidone in human plasma. Both drugs were extracted by liquid–liquid extraction with ethyl acetate and saturated borax solution. The chromatographic separation was performed on a reversed-phase C18 column with a mobile phase of water–methanol (2:98, v/v) containing 0.5% formic acid. The protonated analyte was quantitated in positive ionization by multiple reaction monitoring with a mass spectrometer. The assay exhibited linearity over the concentration range of 3.33–500 ng mL⁻¹ for itopride hydrochloride and 3.33–100 ng mL⁻¹ for domperidone in human plasma. The precursor to product ion transitions of m/z 359.1–72.3 and 426.0–147.2 were used to measure itopride hydrochloride and domperidone respectively. The method was found suitable for the analysis of plasma samples collected during phase 1 pharmacokinetics study of itopride HCl 50 mg and domperidone 20 mg in 12 healthy volunteers after single oral doses of the combination drug.

     

LC–MS Method for the Quantification of Clonazepam in Rat Plasma

A sensitive and specific high-performance liquid chromatography–tandem mass spectrometry method has been developed and validated for the determination of clonazepam in rat plasma. Clonazepam and internal standard diazepam were extracted from plasma samples by a single-step protein precipitation. The chromatographic separation was performed on a Dikma ODS-C18 reversed-phase column at 40 °C. The mobile phase composed of a premix of solvent A (0.1% formic acid–4 mM ammonium acetate–water)–solvent B (acetonitrile) (13:87, v/v) at a flow-rate of 0.7 mL min⁻¹. Positive electrospray ionization was utilized as the ionization source. Clonazepam and the internal standard were determined using multiple reaction monitoring of precursor → product ion transitions at m/z 316.0 → 270.0 and m/z 285.1 → 193.2, respectively. The lower limit of quantification was 0.25 ng mL⁻¹ using 50 μL plasma samples and the linear calibration range was from 0.25 to 128 ng mL⁻¹. The within- and between-batch RSDs were lower than 15% and the relative recoveries of clonazepam ranged from 97.4 to 104.7%. The mean extraction recoveries of clonazepam and IS were 79.7 and 77.6%, respectively. The method has been successfully applied to the pharmacokinetic studies in rat after oral administration of clonazepam.

     

Temperature dependent rate constant for the reaction of H-atoms with carbonyl sulfide

The kinetics of the reaction of H-atom with carbonyl sulfide (OCS) has been investigated at nearly 2 Torr total pressure of helium over a wide temperature range, T = 255–960 K, using a low-pressure discharge flow reactor combined with an electron impact ionization quadrupole mass spectrometer. The rate constant of the reaction H + OCS → SH + CO (1) was determined under pseudo-first order conditions, monitoring the kinetics of H-atom consumption in excess of OCS, k₁ = 6.6 × 10⁻¹³ × (T/298)³ × exp(−1150/T) cm³ molecule⁻¹ s⁻¹ (with estimated total uncertainty on k₁ of 15% at all temperatures). Current measurements of k₁ at intermediate temperatures (520–960 K) appear to reconcile previous high and low temperature data and allow the above expression for k₁ to be recommended for use in the extended temperature range between 255 and 1830 K with a conservative uncertainty of 20%.     

Determination of mercury in organic solvents and gas condensates by μflow-injection — inductively coupled plasma mass spectrometry using a modified total consumption micronebulizer fitted with single pass spray chamber

A high-throughput flow-injection — inductively coupled plasma mass spectrometry (ICP MS) analytical method was developed for the determination of mercury in gas condensates and carbon-rich solvents. The sample (undiluted or diluted 10-fold) was introduced via a modified total consumption micronebulizer working at a flow rate of 30 μl min^− 1 and fitted with a singlepass spray chamber. This low flow rate and the addition of oxygen (70 ml min^− 1) assured the plasma stability and reduced the carbon build-up on the interface and on ion lenses. A limit of detection of 0.5 ng g^− 1 (2.5 μl sample) was obtained owing to the reduction of dead volume and sample dispersion (peak-width was 3 s at half-height) in the liquid pass of the nebulizer. The elimination of the memory effect reduced the washout time down to 30 s which resulted in a throughput of ca. 60 h^− 1. The method was validated by the analysis of 3 gas condensates by cold vapour atomic absorption spectrometry.     

Inline pneumatically assisted atmospheric pressure matrix‐assisted laser desorption/ionization ion trap mass spectrometry

Atmospheric pressure (AP) matrix‐assisted laser desorption/ionization (MALDI) is known to suffer from poor ion transfer efficiencies as compared to conventional vacuum MALDI (vMALDI). To mitigate these issues, a new AP‐MALDI ion source utilizing a coaxial gas flow was developed. Nitrogen, helium, and sulfur hexafluoride were tested for their abilities as ion carriers for a standard peptide and small drug molecules. Nitrogen showed the best ion transport efficiency, with sensitivity gains of up to 1900% and 20% for a peptide standard when the target plate voltage was either continuous or pulsed, respectively. The addition of carrier gas not only entrained the ions efficiently but also deflected background species and declustered analyte–matrix adducts, resulting in higher absolute analyte signal intensities and greater signal‐to‐noise (S/N) ratios. With the increased sensitivity of pneumatically assisted (PA) AP‐MALDI, the limits of detection of angiotensin I were 20 or 3 fmols for continuous or pulsed target plate voltage, respectively. For analyzing low‐mass analytes, it was found that very low gas flow rates (0.3–0.6 l min^?1) were preferable owing to increased fragmentation at higher gas flows. The analyte lability, type of gas, and nature of the extraction field between the target plate and mass spectrometer inlet were observed to be the most important factors affecting the performance of the in‐line PA‐AP‐MALDI ion source. Copyright © 2010 John Wiley & Sons, Ltd.     

Simultaneous LC–MS Analysis and of Wogonin and Oroxylin A in Rat Plasma,and Pharmacokinetic Studies After Administration of the Active Fraction from Xiao-Xu-Ming Decoction

A rapid and specific high-performance liquid chromatographic method coupled with electrospray ionization mass spectrometric detection has been developed and validated for identification and quantification of wogonin and oroxylin A in rat plasma. Wogonin, oroxylin A, and diazepam (internal standard) were extracted from plasma samples by liquid–liquid extraction with ethyl acetate. Chromatographic separation was achieved on a C₁₈ column with acetonitrile–0.6% aqueous formic acid 35:65 (v/v) as mobile phase at a flow rate of 0.2 mL min⁻¹. Detection was performed with a single-quadrupole mass spectrometer in selected-ion-monitoring (SIM) mode. Linearity was good within the concentration range 14.4–360 ng mL⁻¹ for wogonin and 10.8–271 ng mL⁻¹ for oroxylin A; the correlation coefficients (r ²) were 0.9999. The intra-day and inter-day precision, as RSD, was below 12.4%, and accuracy ranged from 81.1 to 111.9%. The lower limit of quantification was 14.4 ng mL⁻¹ for wogonin and 10.8 ng mL⁻¹ for oroxylin A. This method was successfully used in the first pharmacokinetic study of wogonin and oroxylin A in rat plasma after oral administration of the active fraction from Xiao-xu-ming decoction.

     

Transformation of the gas‐phase favored O‐protomer of p‐aminobenzoic acid to its unfavored N‐protomer by ion activation in the presence of water vapor: An ion‐mobility mass spectrometry study

An ion‐mobility mass spectrometry study showed that the preferred O‐protonated form of p‐aminobenzoic in the gas phase can be converted to the thermodynamically less favored N‐protomer by in‐source collision‐induced ion activation during the ion transfer process from the atmospheric region to the first vacuum region if the humidity is high in the ion source. Upon the addition of water vapor to the nitrogen gas used to promote the solid analyte to the gas phase under helium‐plasma ionization conditions, the intensity of the ion‐mobility arrival‐time peak for the N‐protomer increased dramatically. Evidently, the ion‐activation process in the first vacuum region is able to provide the energy required to surmount the barrier to isomerize the O‐protomer to the more energetic N‐protomer. The transfer of the proton attached to the carbonyl oxygen atom of the O‐protomer to the amino group takes place by a water‐bridge mechanism. Apparently, the postionization transformations that take place during the transmission of ions from the atmospheric‐pressure ion source to the detector, via different physical compartments of low to high vacuum, play an eminent role in determining the population ratios eventually manifested at the detector.     

Coupling a Wireless Bipolar Ultramicroelectrode with Nano-electrospray Ionization Mass Spectrometry: Insights into the Ultrafast Initial Step of Electrochemical Reactions

We report a new mass spectrometric method for detecting electrogenerated intermediates. This approach is based on simultaneous activation of electrospray ionization and redox reaction on a wireless bipolar ultramicroelectrode, which is fabricated in the tip of a quartz nanopipette. The hollow structure of the ultramicroelectrode permits rapid transferring the transient species from electrode–electrolyte interfaces into the gas phase for mass spectrometric identification on the time scale of microseconds. The long-sought fleeting intermediates including TPrA^.+, whose lifetime in solution is only 200 μs, and catecholamine o-semiquinone radicals, the second-order rate constant of which is typically 10⁹ m ⁻¹ s⁻¹, were successfully identified, helping clarify the previously hidden reaction pathways. Accordingly, our method may have wide applicability in exploring the dynamics of many electrochemical reactions, especially their ultrafast initial steps.     

Simultaneous Determination of Resibufogenin and Its Major Metabolite 3-epi-Resibufogenin in Rat Plasma by HPLC Coupled with Tandem Mass Spectrometry

A rapid, sensitive and specific method for the simultaneous quantification of resibufogenin (RBG) and 3-epi-resibufogenin (3-ERBG) in rat plasma was developed by using a liquid–liquid extraction procedure and liquid chromatography–electrospray ionization/tandem mass spectrometric (LC–ESI–MS/MS) analysis. The separation was performed by HPLC on a reversed phase C₁₈ HPLC column (150 × 2.1 mm, 3.5 μm) using a mobile phase of acetonitrilel-0.1% formic acid aqueous solution (45:55, v/v). The determination was performed by a triple-quadrupole mass spectrometer in the multiple reaction monitoring using positive mode of electrospray ionization (ESI). The calibration curves were both linear (R > 0.995) over the concentration range of 3.0–5,000 ng mL⁻¹, and the lower limits of quantification were 3.0 ng mL⁻¹ for both RBG and 3-ERBG. The intra-day and inter-day precisions (% RSD) were all less than 15%, and the accuracies (%RE) were within the range of ±15%. The mean recoveries of RBG, 3-ERBG and IS were over 82.7, 84.8 and 90.0% (n = 6), respectively. The method was proved to be rapid, sensitive and specific, and has been successfully applied to determine RBG and its major metabolite 3-ERBG in rat plasma after oral administration of RBG for pharmacokinetic study. Comparison of pharmacokinetic data with anti-tumor activities of RBG and ERBG suggested that 3-ERBG, as a major metabolite of RBG in rats, was perhaps also a bioactive form of RBG in vivo.

     

Determination of arsenic compounds in marine mammals with high-performance liquid chromatography and an inductively coupled plasma mass spectrometer as element-specific detector

Total arsenic concentrations and the concentrations of individual arsenic compounds were determined in liver samples of pinnipeds [nine ringed seals (Phoca hispida), one bearded seal (Erginathus barbatus)] and cetaceans [two pilot whales (Globicephalus melas), one beluga whale (Deliphinapterus leucus)]. Total arsenic concentrations ranged from 0.167 to 2.40 mg As kg⁻¹ wet mass. The arsenic compounds extracted from the liver samples with a methanol/water mixture (9:1, v/v) were identified and quantified by anion- and cation-exchange chromatography. An ICP–MS equipped with a hydraulic high-pressure nebulizer served as the arsenic-specific detector. Arsenobetaine (0.052–1.67 mg As kg⁻¹ wet mass) was the predominant arsenic compound in all the liver samples. Arsenocholine was present in all livers (0.005–0.044 mg As kg⁻¹ wet mass). The tetramethylarsonium cation was detected in all pinnipeds ( < 0.009 to 0.043 mg As kg⁻¹) but not in any of the cetaceans. The concentration of dimethylarsinic acid ranged from < 0.001 to 0.109 mg As kg⁻¹ wet mass. Most of the concentrations for methylarsonic acid ( < 0.001 to 0.025 mg As kg⁻¹ wet mass) were below the detection limit. Arsenous acid and arsenic acid concentrations were below the detection limit of the method (0.001 mg As kg⁻¹). An unknown arsenic compound was present in all liver samples at concentrations from 0.002–0.027 mg As kg⁻¹. © 1998 John Wiley & Sons, Ltd.     

Temperature-dependent rate constant for the reaction of F atoms with HNO3

The kinetics of the reaction of F atom with HNO₃, source of NO₃ radicals widely used in laboratory studies, has been investigated at nearly 2.7 mbar total pressure of helium over a wide temperature range, T = 220-700 K, using a low-pressure discharge flow reactor combined with an electron impact ionization quadrupole mass spectrometer. The rate constant of the reaction F + HNO₃ → NO₃ + HF (1) was determined using both relative rate method and absolute measurements under pseudo–first-order conditions, monitoring the kinetics of F-atom consumption in excess of HNO₃, k₁ = (8.2 ± 0.4) × 10⁻¹² exp((315 ± 15)/T) cm³ molecule⁻¹ s⁻¹ (where the uncertainties represent precision at the 2σ level, the estimated total uncertainty on k₁ being 15% at all temperatures). The reaction rate constant was found to be in excellent agreement with the only previous temperature-dependent study. Experiments on detection of the reaction product, HF, have shown that NO₃ and HF forming channel of the title reaction is the dominant, if not unique, on the whole temperature range of the study.     

Gas‐phase protomers of p‐(dimethylamino)chalcone investigated by travelling‐wave ion mobility mass spectrometry (TWIMS)

Results from ion‐mobility (IM) separation experiments demonstrate that O‐ and N‐protomers of p‐(dimethylamino)chalcone (p‐DMAC) can coexist in the gas phase. The relative populations of the two protomers strongly depend on the ion‐generating settings and the conditions the precursor ions experience from the point of their gas‐phase inception to the time of their detection. Under relatively dry source conditions, the ratio of the gas‐phase protomers generated under helium‐plasma ionization (HePI) conditions is biased towards the thermodynamically favored O‐protomer. However, when the humidity of the enclosed ion source was increased, the IM arrival‐time distribution profile of the mass‐selected protonated precursor of p‐DMAC changed rapidly to one dominated by the N‐protomer. Under spray‐ionization conditions, the formation of the thermodynamically less favored protomer has been generally attributed to a phenomenon called kinetic trapping. Herein, we demonstrate that the population of thermodynamically less favored N‐protomer can be dramatically increased simply by introducing water vapor to the HePI ion source.     

Separation and determination of seleno amino acids using gas chromatography hyphenated with inductively coupled plasma mass spectrometry after hollow fiber liquid phase microextraction

A new derivatization–extraction method for preconcentration of seleno amino acids using hollow fiber liquid phase microextraction (HF‐LPME) was developed for the separation and determination of seleno amino acids in biological samples by gas chromatography–inductively coupled plasma mass spectrometry (GC–ICP‐MS). Derivatization was performed with ethyl chloroformate (ECF) to improve the volatility of seleno amino acids. Parameters influencing microextraction, including extraction solvent, pH of sample solution, extraction time, stirring speed, and inorganic salt concentration have been investigated. Under the optimal conditions, the limits of detection (LODs) obtained for Se‐methyl‐selenocysteine (SeMeCys), selenomethionine (SeMet), and selenoethionine (SeEth) were 23, 15, and 11 ng Se l⁻¹, respectively. The relative standard deviations (RSDs) were 14.6%, 16.4%, and 19.4% for SeMeCys, SeMet, and SeEth (c = 1.0 ng ml⁻¹, n = 7), respectively, and the RSDs for SeMeCys, SeMet could be improved obviously if SeEth was utilized as the internal standard. The proposed method was applied for the determination of seleno amino acids in extracts of garlic, cabbage, and mushroom samples, and the recoveries for the spiked samples were in the range of 96.8–108% and 93.4–115% with and without the use of SeEth as internal standard. The developed method was also applied to the analysis of SeMet in a certified reference material of SELM‐1 yeast and the determined value is in good agreement with the certified value. Copyright © 2008 John Wiley & Sons, Ltd.     

Evaluation of needle trap micro‐extraction and solid‐phase micro‐extraction: Obtaining comprehensive information on volatile emissions from in vitro cultures

Volatile organic compounds (VOCs) emitted from in vitro cultures may reveal information on species and metabolism. Owing to low nmol L⁻¹ concentration ranges, pre‐concentration techniques are required for gas chromatography–mass spectrometry (GC–MS) based analyses. This study was intended to compare the efficiency of established micro‐extraction techniques – solid‐phase micro‐extraction (SPME) and needle‐trap micro‐extraction (NTME) – for the analysis of complex VOC patterns. For SPME, a 75 μm Carboxen®/polydimethylsiloxane fiber was used. The NTME needle was packed with divinylbenzene, Carbopack X and Carboxen 1000. The headspace was sampled bi‐directionally. Seventy‐two VOCs were calibrated by reference standard mixtures in the range of 0.041–62.24 nmol L⁻¹ by means of GC–MS. Both pre‐concentration methods were applied to profile VOCs from cultures of Mycobacterium avium ssp. paratuberculosis. Limits of detection ranged from 0.004 to 3.93 nmol L⁻¹ (median = 0.030 nmol L⁻¹) for NTME and from 0.001 to 5.684 nmol L⁻¹ (median = 0.043 nmol L⁻¹) for SPME. NTME showed advantages in assessing polar compounds such as alcohols. SPME showed advantages in reproducibility but disadvantages in sensitivity for N‐containing compounds. Micro‐extraction techniques such as SPME and NTME are well suited for trace VOC profiling over cultures if the limitations of each technique is taken into account.