Development of capillary zone electrophoresis-electrospray ionization-mass spectrometry for the determination of lamotrigine in human plasma

A method of coupling capillary zone electrophoresis (CZE) with electrospray ionization-mass spectrometry (ESI-MS) detection has been developed for monitoring an antiepileptic drug, lamotrigine (LTG) in human plasma. The CZE-MS was developed in three stages: (i) CZE separation and ESI-MS detection of LTG and tyramine (TRM, internal standard) were simultaneously optimized by studying the influence of CZE background electrolyte (BGE) pH, BGE ionic strength, and nebulizer pressure of the MS sprayer; (ii) sheath liquid parameters, such as pH, ionic strength, organic modifier content, and flow rate of the sheath liquid, were systematically varied under optimum CZE-MS conditions developed in the first stage; (iii) MS sprayer chamber parameters (drying gas temperature and drying gas flow rate) were varied for the best MS detection of LTG. The developed assay was finally applied for the determination of LTG in plasma samples. The linear range of LTG in plasma sample assay was between 0.1-5.0 microg/mL with a limit of detection as low as 0.05 microg/mL and run time less than 6 min. Finally, the concentration-time profile of LTG in human plasma sample was found to correlate well when CZE-ESI-MS was compared to a more established method of high-performance liquid chromatography with ultraviolet detection.     

Chemometric approach to evaluate the parameters affecting electrospray: application of a statistical design of experiments for the study of arginine ionization

The effects of different experimental parameters on arginine electrospray ionization have been investigated with response surface modelling design. This chemometric technique allows a study of the effects of selected experimental variables and their interactions on the response of an experiment by performing a limited number of analyses. Six variables were studied: methanol content in the liquid phase, formic acid concentration, electrospray voltage, orifice voltage, mobile phase flow rate, and sheath gas flow rate. Signal abundance and signal-to-noise ratio of the protonated molecule and the protonated dimer were measured from the electrospray mass spectra and these four responses were tested by the design. The factor that exhibits the greatest influence on MH+ abundance is shown to be the liquid flow rate whereas the formation of protonated dimer is mainly controlled by the percentage of methanol in the mobile phase. A strong synergic effect of methanol content and formic acid concentration in the liquid has also been demonstrated in the study of noise level. Moreover, the capabilities of the multicriteria optimization method have been demonstrated through a successful prediction of a set of optimal experimental conditions.     

Rapid and direct analysis of gamma-hydroxybutyric acid in urine by capillary electrophoresis-electrospray ionization ion-trap mass spectrometry

The present work was aimed at the development of a capillary electrophoretic analysis of gamma-hydroxybutyric acid (GHB) using electrospray ion trap mass spectrometry to achieve the direct and unequivocal detection of this analyte in human urine. Optimized capillary electrophoretic conditions were: injection, 20 s at 0.5 psi (1 psi = 6894.76 Pa); buffer electrolyte, 12.5 mM ammonium formate adjusted to pH 8.35 with diethylamine; fused silicacapillary: 100 cm x 50 microm i.d.; separation voltage, 25 kV (forward polarity) + 0.5 psi; room temperature. Electrospray and mass spectrometric conditions were: drying gas and nebulizing gas (nitrogen) at flow rate 3 l/min, temperature 250 degrees C, nebulizer pressure: 10 psi; sheath liquid solution: methanol-water (90:10) containing 0.1% ammonia delivered at 3 microl/min; spray voltage 3.5 kV. Mass spetrometric detection was carried out in the selected ion monitoring mode of negative molecular ions at 103 m/z for GHB and 115 m/z for maleic acid (I.S.). Under these conditions the baseline separation of GHB and the I.S. was obtained. The selectivity of the analysis allowed for direct injection of unextracted urine, previously diluted 1:4 with water. Linearity was assessed in the GHB concentration range from 80 to 1280 microg/ml in urine. Analytical sensitivity (as limit of detection) resulted about 5 microg/ml in water and 20 microg/ml in original urine. Analytical precision was fairly acceptable with R.S.D. values lower than 5% for migration times and 18% for quantitation in real samples, in both intra day and day-to-day experiments. On these grounds, the developed method can be adopted for rapid identification of acute intoxications from GHB in humans.     

Coupling of capillary electrophoresis with electrospray ionization multiplexing ion mobility spectrometry

In this work, ion mobility spectrometry (IMS) function as a detector and another dimension of separation was coupled with CE to achieve two‐dimensional separation. To improve the performance of hyphenated CE‐IMS instrument, electrospray ionization correlation ion mobility spectrometry is evaluated and compared with traditional signal averaging data acquisition method using tetraalkylammonium bromide compounds. The effect of various parameters on the separation including sample introduction, sheath fluid of CE and drift gas, data acquisition method of IMS were investigated. The experimental result shows that the optimal conditions are as follows: hydrodynamic sample injection method, the electrophoresis voltage is 10 kilo volts, 5 mmol/L ammonium acetate buffer solution containing 80% acetonitrile as both the background electrolyte and the electrospray ionization sheath fluid, the ESI liquid flow rate is 4.5 μL/min, the drift voltage is 10.5 kilo volts, the drift gas temperature is 383 K and the drift gas flow rate is 300 mL/min. Under the above conditions, the mixture standards of seven tetraalkylammoniums can be completely separated within 10 min both by CE and IMS. The linear range was 5–250 μg/mL, with LOD of 0.152, 0.204, 0.277, 0.382, 0.466, 0.623 and 0.892 μg/mL, respectively. Compared with traditional capillary electrophoresis detection methods, the developed CE‐ESI‐IMS method not only provide two sets of qualitative parameters including electrophoresis migration time and ion drift time, ion mobility spectrometer can also provide an additional dimension of separation and could apply to the detection ultra‐violet transparent compounds or none fluorescent compounds.     

Study of biodegradation products from azo dyes in fungal degradation by capillary electrophoresis/electrospray mass spectrometry

Biodegradation products from four model sulfonated azo dyes Orange II, Acid Orange 8, Food Yellow 3, and 4-[(4-hydroxyphenyl)azo]-benzenesulfonic acid, sodium salt (4HABA), during fungal degradation were determined by capillary electrophoresis coupled with ion trap mass spectrometry (CE-MS) with electrospray ionization and a coaxial sheath flow interface. The development and optimization of this analytical method including the sheath liquid composition and flow rate, nebulizing gas flow rate, carrier electrolyte, and MS voltage are described herein. Detection of unknown biodegradation products was carried out under negative ion mode with base peak electrophorogram (BPE) or extractive ion electrophorogram (EIE) monitoring. A volatile ammonium acetate buffer (10 mM) without organic modifier and a shealth liquid made from 2-propanol and water (80:20, v/v) were suited for the separation and ESI interface. The sulfonated ion was the base peak for model azo dyes and their metabolites containing sulfonic group. Results showed that the tested azo dyes were degraded quickly in the culture of white rot fungus, Pleurotus ostreatus in 3 days with the major biodegradation products being 4-hydroxy-benzenesulfonic acid, 3-methyl-4-hydroxy-benzenesulfonic acid, benzenesulfonic acid, 1,2-naphthoquinone-6-sulfonic acid and 3-methyl-benzenesulfonic acid.     

Coupling CE with atmospheric pressure photoionization MS for pharmaceutical basic compounds: optimization of operating parameters

The use of CE coupled with MS (CE-MS) has evolved as a useful tool to analyze charged species in small sample volumes. Because of its sensitivity, versatility and ease of implementation, the ESI interface is currently the method of choice to hyphenate CE to MS. An alternative can be the atmospheric pressure photoionization (APPI) source, however, numerous parameters must be optimized for its coupling to CE. After evaluation of the sheath liquid composition and the CE capillary outlet position, an experimental design methodology was assessed for optimizing other ionization source parameters, such as sheath liquid flow rate, drying gas flow rate and temperature, nebulizing gas pressure, vaporizer temperature, and capillary voltage. For this purpose, a fractional factorial design (FFD) was selected as a screening procedure to identify factors which significantly influence sensitivity and efficiency. A face-centered central composite design (CCD) was then used to predict and optimize sensitivity, taking into account the most relevant variables. Sensitivity was finally evaluated with the optimized conditions and height-to-noise ratios (H/N) around 10 were achieved for an injection of 200 ng/mL of each analyte.     

Application of polymeric surfactants in micellar electrokinetic chromatography-electrospray ionization mass spectrometry of benzodiazepines and benzoxazocine chiral drugs

Chiral micellar EKC (CMEKC) coupled to ESI-MS using polymeric surfactants as pseudostationary phases is investigated for simultaneous enantioseparation of two benzodiazepines, (+/-)-oxazepam ((+/-)-OXA) and (+/-)-lorazepam ((+/-)-LOR), and one benzoxazocine, (+/-)-nefopam ((+/-)-NEF). First, enantioselectivity and electrospray sensitivity of six chiral polymeric surfactants for all three chiral compounds are compared. Second, using poly(sodium N-undecenoyl-L-leucinate) as pseudostationary phase, the organic modifiers (methanol (MeOH), isopropanol, and ACN) are added into the running buffer to further improve chiral resolution (RS). Next, a CMEKC-ESI-MS method for the simultaneous enantioseparation of two benzodiazepines is further developed by using a dipeptide polymeric surfactant, poly(sodium N-undecenoxy carbonyl-L,L-leucyl-valinate) (poly-L,L-SUCLV). The CMEKC conditions including nebulizer pressure, capillary length, ammonium acetate concentration, pH, poly-L,L-SUCLV concentration, and capillary temperature were optimized to achieve maximum chiral RS and highest sensitivity of MS detection. The spray chamber parameters (drying gas temperature and drying gas flow rate) as well as sheath liquid conditions (MeOH content, pH, flow rate, and ionic strength) were found to significantly influence MS S/N of both (+/-)-OXA and (+/-)-LOR. Finally, a comparative study between simultaneous UV and MS detection showed high plate numbers, better chiral RS, and enhanced detectability with CMEKC-MS. However, speed of analysis was faster using CMEKC-UV.     

Nonaqueous CE ESI‐IT‐MS analysis of Amaryllidaceae alkaloids

The Amaryllidaceae are widely distributed medical plants. Lycorine, lycoramine, lycoremine, and lycobetaine are the major active alkaloids in Amaryllidaceae plants. A nonaqueous CE ESI‐IT‐MS method for separation, identification, and quantification of the Amaryllidaceae alkaloids has been developed. The MS^1–3 behavior has been studied and the fragmentation pathways of main fragment ions have been proposed. The effects of several factors such as composition and concentration of buffer, applied voltage, composition, and flow rate of the sheath liquid, nebulizing gas pressure, flow rate, and temperature of drying gas were investigated. Under the optimal conditions, the linear concentration range of these compounds was wide with the correlation coefficient (R²) >0.99. RSDs of migration time and peak areas were <10%. The LODs were <240 ng/mL. The proposed method can be successfully applied to the determination of the related alkaloids in the Lycoris radiata roots.     

Development of a CE-ESI-microTOF-MS method for a rapid identification of phenolic compounds in buckwheat

A sensitive CE-ESI-MS analytical method for the identification of buckwheat antioxidants has been developed. CE and ESI-TOF parameters (e.g. buffer composition and pH, sheath liquid composition, sheath liquid and gas flow rates, electrospray voltage) were optimized to obtain an optimal analytical separation and identification. The results confirmed the presence of phenolic acids, procyanidins and galloylated propelargonidins. The identification of swertiamacroside and 2-hydroxy-3-O-β-D-glucopyranosil-benzoic acid, found for the first time in our previous work, has been confirmed. Furthermore, 5,7,4'-trimethoxyflavan and dihydroxy-trimethoxyisoflavan have also been tentatively identified for the first time in buckwheat.     

Behaviour of tetraalkylammonium ions in high‐field asymmetric waveform ion mobility spectrometry

High‐field asymmetric waveform ion mobility spectrometry (FAIMS) is an ion‐filtering technique recently adapted for use with liquid chromatography/mass spectrometry (LC/MS) to remove interferences during analysis of complex matrices. This is the first systematic study of a series of singly charged tetraalkylammonium ions by FAIMS‐MS. The compensation voltage (CV) is the DC offset of the waveform which permits the ion to emerge from FAIMS and it was determined for each member of the series under various conditions. The electrospray ionization conditions explored included spray voltage, vaporizer temperature, and sheath and auxiliary gas pressure. The FAIMS conditions explored included carrier gas flow rate, electrode temperature and composition of the carrier gas. Optimum desolvation was achieved using sufficient carrier gas (flow rate ≥2 L/min) to ensure stable response. Low‐mass ions (m/z 100–200) are more susceptible to changes in electrode temperature and gas composition than high mass ions (m/z 200–700). As a result of this study, ions are reliably analyzed using standard FAIMS conditions (dispersion voltage ?5000 V, carrier gas flow rate 3 L/min, 50% helium/50%nitrogen, inner electrode temperature 70°C and outer electrode temperature 90°C). Variation of FAIMS conditions may be of great use for the separation of very low mass tetraalkylammonium (TAA) ions from other TAA ions. The FAIMS conditions do not appear to have a major effect on higher mass ions. Copyright © 2010 John Wiley & Sons, Ltd.     

Optimization of capillary electrophoretic-electrospray ionization-mass spectrometric analysis of catecholamines

The capillary electrophoretic-mass spectrometric analysis (CE-MS) of catecholamines was optimized with coaxial sheath flow interface and electrospray ionization (ESI). The parameters studied included the sheath liquid composition and its flow rate, separation conditions in ammonium acetate buffer together with the ESI and cone voltages as mass spectrometric parameters. In addition, the effect of ESI voltage on injection as well as the siphoning effect were considered. The optimized conditions were a sheath liquid composition of methanol-water (80:20 v/v) with 0.5% acetic acid, with a flow rate of 6 microL/min. The capillary electrophoretic separation parameters were optimized with 50 mM ammonium acetate buffer, pH 4.0, to +25 kV separation voltage together with a pressure of 0.1 psi. The most intensive signals were obtained with an ESI voltage of +4.0 kV and a cone voltage of +20 V. The nonactive ESI voltage during injection as well as avoidance of the siphoning effect increased the sensitivity of the MS detection considerably. The use of ammonium hydroxide as the CE capillary conditioning solution instead of sodium hydroxide did not affect the CE-MS performance, but allowed the conditioning of the capillary between analyses to be performed in the MS without contaminating the ion source.     

Development of a liquid chromatography-electrospray mass spectrometric method for the simultaneous analysis of benzoxazolinones and their degradation products

A new method for the simultaneous analysis of some benzoxazolinones, aminophenoxazinones and malonamic acids was developed based on liquid chromatography (LC) coupled to mass spectrometry (MS), using electrospray ionization (ESI) and operating in positive mode. Different ESI-MS parameters, such as fragmentor voltage, capillary voltage, drying gas flow, nebulizer gas pressure and drying gas temperature, were optimized in order to obtain structural information and to achieve maximum sensitivity. Chromatographic separation was performed by a reversed-phase LC column using a linear gradient of water and methanol. Quality assurance of the developed method was assessed by measuring parameters as linearity, sensitivity, repeatability and reproducibility. Quantification method based on the use of internal standard was developed, selecting synthetic 2-methoxy-2H-1,4-benzoxazin-3(4H)-one as internal standard. Good correlations were obtained for all analytes relative to this compound in the range of 0.05-1.5 ng/microL. Instrumental detection limits were between 0.02 and 0.2 ng/microL. Repeatability and reproducibility studies showed acceptable coefficient of variation values.     

Simultaneous chiral separation and determination of ephedrine alkaloids by MEKC-ESI-MS using polymeric surfactant I: method development

In this work, simultaneous separation of eight stereoisomers of ephedrine and related compounds ((+/-)-ephedrine, (+/-)-pseudoephedrine, (+/-)-norephedrine and (+/-)-N-methylephedrine) was accomplished using a polymeric chiral surfactant, i.e. polysodium N-undecenoxycarbonyl-L-leucinate (poly-L-SUCL) by chiral (C)MEKC-ESI-MS. The conditions of CMEKC were first investigated. The baseline separation of all eight stereoisomers of ephedrine and related compounds was achieved under optimum CMEKC conditions (35 mM poly-L-SUCL, 15 mM NH(4)OAc, pH 6.0, 30% v/v ACN, 30 kV and 20 degrees C) in less than 30 min. Next, a central composite design for response surface modeling has been described to evaluate the electrospray chamber parameters and the sheath liquid conditions. Optimum mass abundance of stereoisomers of ephedrine and related compounds was observed using the spray chamber parameters, namely 250 degrees C drying gas temperature and 8 L/min drying gas flow rate at a nebulizer pressure of 4 psi. Furthermore, the experimental design indicates that the optimum mass abundance of the stereoisomers of ephedrine and related compounds can be obtained using a sheath liquid containing 80:20 v/v methanol-water, 5 mM NH(4)OAc at pH 8.5 delivered at 5 microL/min. Finally, compared to MEKC-UV, the use of poly-L-SUCL in MEKC-MS provided significantly higher sensitivity for stereoisomers of ephedrine and related compounds.     

Continuous full filling capillary electrochromatography-electrospraying chromatographic nanoparticles

The influence of instrumental parameters affecting the ionization in continuous full filling capillary electrochromatography/electrospray ionization mass spectrometry (CFF‐CEC/ESI‐MS) was investigated. The investigated parameters were the BGE and sheath liquid ion strength and organic modifier content, the nebulizer gas pressure, and the concentration of nanoparticles in the BGE. It was found that the nebulizer pressure had the largest influence on the separation efficiency and apparent retention. It was shown that even the lowest pressure investigated was sufficient to guide the nanoparticle flow away from the mass spectrometer inlet. A nebulizer pressure of 5 psi was found to be optimal; increasing the pressure significantly decreased the separation efficiency due to the generation of a hydrodynamic flow. Generally, the ion strength of both the BGE and the sheath liquid were found to have very moderate effects on the separation of a homologous series of dialkyl phthalates, whereas the ionization efficiency was found to be unaffected by the nanoparticles and the separation efficiency was found to increase with increasing concentrations up to 3.8 mg/mL, whereafter it was observed to drop. The optimized method was linear over a wide concentration range and presented LOD and LOQ more than threefold lower than those previously reported using CFF‐CEC/ESI‐MS.     

Analyses of alkaloids in different products by NACE-MS

A simple method for the separation and characterization of five nicotine-related alkaloids by NACE employing UV and MS detections is described here for the first time. Several factors, including NACE parameters (compositions of running solution) and MS parameters (such as nature and flow rate of sheath liquid, pressure of nebulization gas, and flow rate of dry gas), were optimized in order to obtain both an adequate CE separation and high MS signals for the alkaloid compounds used in this study. A reliable CE separation of five alkaloids was achieved in 50 mM ammonium formate that was dissolved in an ACN/methanol mixture (50:50, v/v) of pH* 4.0 (apparent pH 4.0). The optimal electrospray MS measurement was carried out in the positive ionization mode using a coaxial sheath liquid composed of isopropyl alcohol and water in the ratio of 80:20 v/v at a flow rate of 180 microL/h. In addition, the proposed NACE method was also applied in the analyses of alkaloids in several products including chewing gums, beverages, and tobaccos. This NACE-MS method was found to provide a better detection ability and separation resolution for the analysis of nicotine alkaloids when compared to other aqueous CE-MS reports.     

Characterization of the methanolic extract of hops using capillary electrophoresis-electrospray ionization-mass spectrometry

Hops are used almost exclusively for bitterness and flavor by brewers. We propose the first analytical application of CZE coupled to ESI-MS for the separation and structural elucidation of organic compounds in the methanolic extracts of hops, and different extraction procedures of the plant material have been carried out. The proposed method permits the identification of hop polyphenols (flavonoids glycosides and chalcones), bitter acids (alpha-acids and beta-acids), and their oxidation products. The optimization of CZE parameters (pH, concentration, and type of buffer) and ESI-MS parameters (nature and flow rate of the sheath liquid, nebulizer pressure, drying gas flow rate, temperature, and compound stability) have permitted the development of a rapid, simple, direct, and straightforward CZE-ESI-MS method for the identification of components of methanolic extracts from different hops used in the brewing process.     

Chiral micellar electrokinetic chromatography-atmospheric pressure photoionization of benzoin derivatives using mixed molecular micelles

In the present work we report, for the first time, the successful on-line coupling of chiral MEKC (CMEKC) to atmospheric pressure photoionization MS (APPI-MS). Four structurally similar neutral test solutes (e.g. benzoin (BNZ) derivatives) were successfully ionized by APPI-MS. The mass spectra in the positive ion mode showed that the protonated molecular ions of BNZs are not the most abundant fragment ions. Simultaneous enantioseparation by CMEKC and on-line APPI-MS detection of four photoinitiators, hydrobenzoin, BNZ, benzoin methyl ether, benzoin ethyl ether, were achieved using an optimized molar ratio of mixed molecular micelle of two polymeric chiral surfactants (polysodium N-undecenoxy carbonyl-L-leucinate and polysodium N-undecenoyl-L,L-leucylvalinate). The CMEKC conditions, such as voltage, chiral polymeric surfactant concentration, buffer pH, and BGE concentration, were optimized using a multivariate central composite design (CCD). The sheath liquid composition (involving %v/v methanol, dopant concentration, electrolyte additive concentration, and flow rate) and spray chamber parameters (drying gas flow rate, drying gas temperature, and vaporizer temperature) were also optimized with CCD. Models built based on the CCD results and response surface method were used to analyze the interactions between factors and their effects on the responses. The final overall optimum conditions for CMEKC-APPI-MS were also predicted and found in agreement with the experimentally optimized parameters.     

Novel approach for developing urinary nucleosides profile by capillary electrophoresis-mass spectrometry

A simple, rapid and efficient capillary electrophoresis-mass spectrometry (CE-MS) method was developed to analyze urinary nucleosides for the first time. The composition of CE buffer and MS parameters were systematically optimized. The optimum buffer was 150 mM acetic acid containing 15% methanol and 15% ethanol. The optimum MS parameters were: methanol containing 0.5% acetic acid was selected as the sheath liquid and the flow rate was 5 microL/min; the flow rate and temperature of drying gas were 6L/min and 150 degrees C, respectively; the pressure of nebulizing gas was 2 psig; and the fragmentor and ESI voltage were 100 V and 4000 V, respectively. Under the optimum CE-MS conditions, the urinary nucleosides were separated within 18 min. The linearity between the relative peak areas and the corresponding concentration of nine nucleosides markers were excellent. The limits of detection (S/N=3) of markers were 0.00862-3.82 nmol/mL. The optimum CE-MS method was applied to analyze urine from 20 bladder cancer patients and 20 healthy volunteers. Considering the standards of many nucleosides cannot be obtained, it is not the ratios of the concentrations of nucleosides to that of creatinine in the literatures, but the ratios of the relative peak area of nucleosides to the concentration of creatinine that used for pattern recognition. And, the statistical analysis result indicated this method was feasible.     

Determination of peptide hormones of brain and intestine by CE with ESI-MS detection

A new method for the determination of the peptide hormones of brain and intestine based on CE coupling with a DAD and ESI-MS was established. Several electrophoretic and ESI-MS parameters were investigated in detail, such as electrolyte nature and concentration, organic solvent and sheath liquid compositions, nebulization gas pressure and the ESI capillary voltage. Optimized conditions were achieved with 25 mM formic acid-ammonium formate (pH 2.9) as the optimal electrolyte, 2 mM formic acid in 80% methanol in water as the sheath liquid, and 20 kV applied voltage. Under the optimized conditions, four protonated peptides were separated by CE and selectively detected by a quadrupole mass spectrometer with a sheath flow ESI interface. LODs for the four peptides (neurotensin hexapeptide, neurotensin, cholecystokinin tetrapeptide, and pentagastrin) were in the range of 0.10-0.60 micromol/L at an S/N of 3. The RSDs (n = 8) of the method were 0.70-1.5% for migration times and 1.6-6.1% for peak areas. This method is simple, rapid, and selective compared with RIA and ELISA techniques, and has been applied to the analysis of rat hypothalamus tissue.     

Development of a capillary zone electrophoresis-electrospray ionisation tandem mass spectrometry method for the analysis of fluoroquinolone antibiotics

The applicability of a capillary zone electrophoresis–electrospray ionisation tandem mass spectrometric (CZE–ESI-MS–MS) method for the separation of nine fluoroquinolones was investigated. Method optimisation involved systematic trouble-shooting starting with the type and duration of capillary pre-washing and conditioning, the choice of both the CE run buffer, MS sheath liquid, CE run potential, ESI spray voltage, sheath gas flow-rate, MS capillary voltage and CE capillary and MS capillary temperatures. Another extremely important factor was found to be the degree to which the CE capillary protrudes into the ESI chamber as well as whether or not sheath gas and spray voltage are employed during the CE injection or not. The importance of the latter has, to our knowledge, not been addressed elsewhere. Nine fluoroquinolones have been separated and detected in a single run by this technique.