High temperature gas chromatography of trimethylsilyl derivatives of alcohol ethoxylates and ethoxysulfates

Conversion of ethoxylated alcohols to trimethylsilyl derivatives and subsequent high temperature gas chromatography allowed for the determination of alkyl chain distribution, mole average degree of ethoxylation and weight percent distribution of several commercial mixtures. Repetitive derivatizations and analyses of a mixture with a vendor specified mole average degree of ethoxylation of 3.0 (Neodol 23-3), yielded an experimental result of 2.93 ± 0.05 (n = 6). Mixtures with different alkyl chain distributions and higher degrees of ethoxylation provided similar accuracy. Extension of the method to the analysis of ethoxylated alcohol sulfate raw materials and ethoxylated alcohol sulfates in dishwashing liquids is discussed.     

Analysis of special surfactants by comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry

Multidimensional gas-chromatographic analyses of olesochemically based nonionic, anionic and several cationic surfactants in industrial cleaners are demonstrated. Comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry allows the simultaneous determination of fatty alcohols, fatty alcohol sulphates and alkyl polyglucosides. In addition, the determination of fatty alcohol ethoxylates up to C₁₀EO₈ (highest degree of ethoxylation) and C₁₈EO₅ (longest C-chain at an ethoxylation degree of five) and the analysis of fatty alcohol alkoxylates that contain ethoxy (EO) and propoxy (PO) groups could be realized. Because of decomposition in the injector and a weak EI-fragmentation, cationic surfactants such as alkyl benzyl dimethyl ammonium chloride could also be identified by their characteristic fragments. Thermogravimetric analyses confirmed that the temperature in a normal GC injector is not high enough to cause thermal decomposition of esterquats. However, we could demonstrate that a modified silylation procedure forms decomposition products of esterquats in the GC injector which are detectable by GC × GC–(TOF)MS and allows the identification of such GC-atypical analytes.     

Total carbon analysis for surfactant adsorption

Total carbon analysis can be utilized for the determination of aqueous surfactant solutions at ppm levels. This method was used to generate adsorption isotherms for purified alcohol ethoxylates on polyester fiber where the effect of the degree of ethoxylation was examined. The generality of the method was shown with cationic surfactant adsorption an inorganic substrates.     

烷基酚聚氧乙烯醚在不同液相色谱分离模式中的分离研究

考察了烷基酚聚氧乙烯醚在反相色谱、正相键合色谱、硅胶吸附色谱、体积排阻色谱4种不同液相色谱分离模式中的分离效果,分别采用Kromasil C_(18)(250 mm× 4.6 mm,5 μm)、Agilent ZORBAX NH2(250 mm× 4.6 mm,5 μm)、Waters Spherisorb S3W(150 mm×2.0 mm,3 μm)和Shodex MSpak GF-310 2D(150 mm×2.0 mm,5 μm)色谱柱,以225 nm为紫外检测波长,对不同液相色谱分离模式的流动相组成、梯度洗脱条件、柱温、流速等进行了优化,并对烷基酚聚氧乙烯醚在不同液相色谱分离模式中的保留机理进行了初步探讨.结果表明,正相键合色谱实现了烷基酚聚氧乙烯醚的最佳分离;硅胶吸附色谱和体积排阻色谱的分离效果较正相键合色谱稍差.     

Nonionic surfactants with linear and branched hydrocarbon tails: compositional analysis, phase behavior, and film properties in bicontinuous microemulsions

Nonionic alcohol ethoxylates are widely used as surfactants in many different applications. They are available in a large number of structural varieties as technical grade products. This variety is mainly based on the use of different alcohols, which can be linear or branched and contain primary, secondary, or tertiary OH groups. Technical grade products are poorly defined as they are composed of alcohol mixtures being different in chain length and structure. On the other hand, monodisperse alcohol ethoxylates are commercially available; however, these surfactants exist only with primary and linear alcohols. In the field of microemulsion research the monodisperse alcohol ethoxylates are widely used. The phase behavior and film properties of these surfactants were studied intensively with respect to the size of the hydrophilic and hydrophobic moieties. Due to the lack of appropriate model surfactants until now, there is little information on how the structure of the hydrocarbon tail influences the microemulsion behavior. To examine structural influences, we synthesized a series of surfactants with the composition C10E5 and having different linear and branched hydrocarbon tails. The surfactants were monodisperse with respect to the hydrocarbon tail but polydisperse with respect to the ethoxylation degree. However, a detailed characterization showed that they were similar concerning the average ethoxylation degree and EO chain length distribution. The phase behavior was investigated for bicontinuous microemulsions, and the film properties were analyzed by small-angle neutron scattering (SANS). Our results show that the structure of the hydrocarbon tail strongly influences the microemulsion behavior. The most efficient surfactant is obtained if the hydrocarbon tail is linear and the hydrophilic group is attached in the C-1 position. Surfactants having the hydrophilic group bound to the C-2 or C-4 position or which contain a branched hydrocarbon tail are less efficient and exhibit in most cases visibly lower phase inversion temperatures. Both the efficiency and temperature behavior mainly can be explained on the basis of increased bulkiness of the branched structures compared to the fully linear version. The phase behavior results are largely confirmed by the SANS investigations. Those results show that the fully linear surfactant exhibits the most rigid interfacial film. In additional experiments this surfactant was compared with its monodisperse analogue. According to the phase diagrams, the surfactant having the polydisperse hydrophilic moiety is drastically more efficient although the film stiffnesses are almost identical.     

Comprehensive analysis of fatty alcohol ethoxylates by ultra high pressure hydrophilic interaction chromatography coupled with ion mobility spectrometry mass spectrometry using a custom‐designed sub‐2 μm column

Comprehensive analysis of fatty alcohol ethoxylates has been conducted by coupling ultra high pressure hydrophilic interaction chromatography and ion mobility spectrometry mass spectrometry. A custom‐designed sub‐2 μm column was used for the chromatographic separation of fatty alcohol ethoxylates by hydrophilic interaction chromatography. Ion mobility spectrometry provided a post‐ionization resolution during a very short period of 6.4 ms. Distinguishable families of singly, doubly, and triply charged fatty alcohol ethoxylates were clearly observed. By virtue of the combination of hydrophilic interaction chromatography and ion mobility spectrometry, comprehensive resolution based on both hydrophobicity difference and mobility disparity has been achieved for fatty alcohol ethoxylates. The orthogonality of the developed separation and analysis system was evaluated with the correlation coefficient and peak spreading angle of 0.0224 and 88.72°, respectively. The actual peak capacity obtained was individually 40 and 193 times than those when hydrophilic interaction chromatography and ion mobility spectrometry were used alone. The collision cross‐sections of fatty alcohol ethoxylates were calculated by calibrating the traveling wave ion mobility device with polyalanine.     

Analysis of polyethoxylated surfactants in microemulsion-oil-water systems: III. Fractionation and partitioning of polyethoxylated alcohol surfactants

Oligomer distribution of polyethoxylated alcohol and polyethoxylated nonylphenol surfactants is studied by normal and reverse-phase high performance liquid chromatography (HPLC). A RP8 column is able to efficiently separate these surfactants according to their alkyl chain (lipophilic) group, while silica and amino columns separate them according to their polyether chain length (hydrophilic group). Polyethoxylated alcohol and polyethoxylated nonylphenol oligomers selectively partition between the microemulsion-oil-water phases of a Winsor III system. Partitioning of these oligomers was analyzed by HPLC with RI detection. The logarithm of the partition coefficient between the water and oil linearly increases with the number of ethylene oxide groups per molecule of oligomer. For a same ethoxylation degree, the partition coefficient of a polyethoxylated tridecanol is found to be higher than the one of the corresponding nonylphenol specie. On the other hand, a polyethoxylated nonylphenol exhibits a higher solubilization than the matching polyethoxylated alcohol.     

微蒸馏气相色谱法测定水中低级脂肪醇的研究

考察了微蒸馏气相色谱法测定水样中多种低级脂肪醇的可行性。利用微蒸馏技术将水中的醇分离富集,用程序升温气相色谱法测定。正丙醇、异丙醇、正丁醇、异丁醇、正戊醇、异戊醇的浓缩倍数分别为169．3,137．6,197．4,149．2,142．7,126．0。检出限分别为0．021,0．031,0．032,0．032,0．066,0．065mg／L。样品中所存在组分的平均回收率分别为甲醇82．60％,正丙醇93．25％,正丁醇94．88％;相对标准偏差分别为甲醇7．7％,正丙醇4．7％,正丁醇3．4％。方法适用于水中多种微量低级醇的同时分析。     

Derivatization of fatty alcohol ethoxylate non‐ionic surfactants using 2‐sulfobenzoic anhydride for characterization by liquid chromatography/mass spectrometry

A derivatization procedure has been developed for the improved characterization of fatty alcohol ethoxylate non‐ionic surfactants by liquid chromatography/mass spectrometry. The end hydroxyl group of each surfactant species was converted into an oxycarbonylbenzene‐2‐sulfonic acid group with 2‐sulfobenzoic anhydride under mild conditions. The produced sulfonic acid group allows all species, including fatty alcohols and those with less than three ethoxylates, to be uniformly ionized by electrospray ionization (ESI) mass spectrometry. Both acid and base can be used as a mobile phase additive for liquid chromatography without affecting M_n and average ethoxylate values, although ion intensities are suppressed during the ESI process. The method was used to analyze seven commercial fatty alcohol ethoxylate non‐ionic surfactants, and the determined M_n and EO values were comparable with the results obtained by NMR. The relative ratio of different fatty alcohol based ethoxylates in a sample can also be determined using the summed mass spectral data. Copyright © 2009 The Dow Chemical Company     

Liquid exclusion-adsorption chromatography, a new technique for isocratic separation of nonionic surfactants. II. Quantitation in the analysis of fatty alcohol ethoxylates

A new technique of liquid chromatography, which allows baseline separation of fatty alcohol ethoxylates with up to 15-20 ethylene oxide units under isocratic conditions allows an accurate quantitative analysis of single hydrophobic chain surfactants. Using density and refractive index detection, the accurate weight fractions of the individual oligomers are obtained. Moreover, the contribution of preferential solvation can be determined. With refractive index detection alone, good accuracy can also be achieved.     

高效液相色谱质谱法分析脂肪醇聚氧乙烯醚中的碳数及环氧乙烷加成数的分布

应用高效液相色谱法将脂肪醇聚氧乙烯醚按碳数和环氧乙烷加成数 (EO数 )分离后 ,在线联用电喷雾离子化质谱 (ESI MS) ,根据其一系列准分子离子峰判断烷基链长和环氧乙烷聚合度。解释了准分子离子峰强度失真的原因。     

Quantitative trace analysis of surfactant mixtures by reversed-phase high-performance liquid chromatography with refractometric detection

Reversed-phase partition liquid chromatography on an octyl column allowed the separation of complex non-ionic poly(ethylene oxide)-type (PEO) surfactant mixtures resulting from the condensation of ethylene oxide with saturated fatty alcohols. As these compounds have no chromophoric group, they were detected by differential refractometry. Accurate quantitation of each oligomer (C_mE_n) allowed the main characteristics of each non-ionic surfactant, i.e., the nature and percentage of the different alkyl chains (with m = number of carbons) and the average number of ethylene oxide units ( ) to be obtained in one analysis. Preparative liquid chromatography was used to isolate pure oligomers with a higher degree of ethoxylation (n =10, 11, 12, 14 and more) than the commercially available standards, in order to determine a wide range of refractometric response factors. It appeared that they are constant as a function of alkyl chain length (C₁₀-C₁₆ range) but that they vary significantly and non-linearly as a function of the degree of ethoxylation, n. It was found that neglecting the variation of response factors can result in a distortion of the average ethoxylation number and in an unsatisfactory quantitative analysis. This chromatographic method, involving a quantitative and reproducible trace enrichment procedure with liquid-solid extraction, allowed the analysis of very dilute PEO mixtures in water. The components of complex PEO mixtures in water were determined at concentrations as low as 0.5 mg 1⁻¹, without any distortion of the distribution, the detection limit being 0.25 μg 1⁻¹ for the less abundant oligomers.     

Analysis of alcohol ethoxylates and alkylamine ethoxylates in agricultural soils using pressurised liquid extraction and liquid chromatography–mass spectrometry

Nonionic surfactants e.g. alcohol ethoxylates (AEOs) and alkylamine ethoxylates (ANEOs) are commonly utilised as adjuvants in pesticide formulations to enhance their effectiveness. In this study, analytical methods for AEO and ANEO determination in soil samples using pressurised liquid extraction (PLE) were developed and used in connection with LC–MS. The recovery of the method, which was highly dependent on the soil properties, varied in the range 47–106% for AEO and 27–109% for ANEO. Detection limits (LOD) were 7–13 µg kg^–1 for AEO and 24–43 µg kg^–1 for ANEO. The developed method has been applied to determine AEOs and ANEOs in surface soil samples from fields sprayed with glyphosate herbicides. Tallowalkylamine ethoxylates (an ANEO) were detected in the soil before and after pesticide application, with increasing concentrations after treatment. The highest concentration in the soil samples was observed for the ANEO homologues with the longest ethoxy chains; in the clay soil the concentration decreased with the length of the ethoxy chain. ANEOs added to pesticide formulations as a technical mixture will, as demonstrated in this study, behave as individual homologues, which is reflected in their behaviour in the environment.Abbreviations AEO Alcohol ethoxylates - ANEO Alkylamine ethoxylates - APEO Alkylphenol ethoxylates - APCI Atmospheric pressure chemical ionisation - ASE Accelerated solvent extraction - CEC Cationic exchange capacity - LC–MS Liquid chromatography–mass spectrometry - LOD Limit of detection - MAE Microwave-assisted extraction - PLE Pressurised liquid extraction - SD Standard deviation - SIM Selected-ion monitoring - SPE Solid-phase extraction - TEA Triethylamine     

高效液相色谱质谱法分析脂肪醇聚氧乙烯醚中的碳数及环氧乙烷加成数的分布

 应用高效液相色谱法将脂肪醇聚氧乙烯醚按碳数和环氧乙烷加成数 (EO数 )分离后 ,在线联用电喷雾离子化质谱 (ESI MS) ,根据其一系列准分子离子峰判断烷基链长和环氧乙烷聚合度。解释了准分子离子峰强度失真的原因。     

Characterization of oligomeric polypropyleneglycol acrylate by GC, SFC and MALDI-TOF-MS.

Polypropyleneglycol acrylate (PGA), one of the typical acrylic oligomers manufactured industrially, was comprehensively characterized by gas chromatography (GC), supercritical fluid chromatography (SFC) and matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF-MS). The homologous series of polypropyleneglycol diacrylate (DA), polypropyleneglycol monoacrylate (MA), and unreacted polypropyleneglycol (PG) were observed as Na adducts in the MALDI-MS spectra of the PGA samples. The relative intensities of these peaks reflect the distributions of the homologues, although their accurate quantification was generally difficult because of change in the ionization efficiency depending on the chemical structure and the molecular weight of the species. On the other hand, the DA and the MA homologues were observed in the chromatograms obtained by SFC in a temperature-programming mode, while the PG homologues were not detected under the given SFC conditions using UV detection. Here, the determination of the degree of polymerization of each component in the chromatograms was accomplished through SFC fractionation for the corresponding peaks, followed again by MALDI-TOF-MS measurement. Furthermore, most of the components in the PGA samples were almost completely separated in the resulting gas chromatograms, and their unequivocal assignments were made also using the retention data on the gas chromatograms of the SFC fractions. As for the quantitative analysis, the relative abundances among DA, MA and PG for lower degrees of polymerization can be easily calculated based on the observed gas chromatograms, whereas the distribution of DA and MA can be estimated from the observed SFC data even for the relatively higher molecular weight fractions, which are generally difficult to determine accurately by GC because of their lower volatility. These results demonstrated that even the complex PGA samples were able to be characterized in detail by using GC, SFC and MALDI-TOF-MS complementarily.     

Detailed molecular characterization of castor oil ethoxylates by liquid chromatography multistage mass spectrometry

The molecular characterization of castor oil ethoxylates (CASEOs) was studied by reverse-phase liquid chromatography (RPLC) mass spectrometry (MS) and multistage mass spectrometry (MS(n)). The developed RPLC method allowed the separation of the various CASEO components, and especially, the baseline separation of multiple nominal isobars (same nominal mass) and isomers (same exact mass). MS and MS(n) were used for the determination and structure elucidation of various structures and for the discrimination of the isobars and isomers. Different ionization techniques and adduct ions were also tested for optimization of the MS detection and the MS(n) fragmentation. A unique fragmentation pathway of ricinoleic acid is proposed, which can be used as a marker of the polymerization process and the topology of ethoxylation in the CASEO. In addition, characteristic neutral losses of ricinoleic acid reveal its (terminal or internal) position in the molecule.     

Quantitative analysis of malto-oligosaccharides by MALDI-TOF mass spectrometry, capillary electrophoresis and anion exchange chromatography

The analysis of malto-oligosaccharides by MALDI-TOF mass spectrometry (MS), capillary electrophoresis (CE) and anion exchange chromatography with pulsed amperometric detection (HPAEC-PAD) is described. Appropriate methods were developed which enabled the resolution of the oligosaccharides and quantification of the peak areas. It could be shown that each technique provided a different distribution profile of the maltodextrins. Using MALDI-TOF MS signals of higher molecular weight oligomers were enhanced while low molecular weight analogues were discriminated. Thus, the response factor depends on the degree of polymerization (DP) of the carbohydrates. Homologues up to DP-15 could be detected. Analysis of the maltodextrins by CE was accomplished by derivatization of the sugars with 4-aminobenzonitrile (ABN) and 8-aminonaphthalene-1,3,6-trisulfonic acid, respectively. By using the latter reagent oligosaccharides up to DP-13 were detected while derivatization with ABN allowed detection up to DP-9. The molecular weight distribution obtained by both approaches were the same. HPAEC-PAD enabled the determination of oligomers up to DP-9. The distribution obtained by this technique showed somewhat lower signals of the small homologues than those found by CE while the opposite held for higher molecular weight compounds. Hydrolysis of the carbohydrates by the derivatization reaction prior to CE analysis, which increased the proportion of low molecular weight homologues, may account for these findings.     

Determination of alkylphenol ethoxylates by micellar electrokinetic chromatography with bile salts

Octyl- and nonylphenol ethoxylates (OPEs and NPEs) with different numbers of ethoxy units (average values: n = 10 and N = 40 for OPEs, and n = 10 for NPEs) were separated by micellar electrokinetic chromatography under positive polarity using an 80 mM borate buffer of pH 8.5 containing sodium deoxycholate (SDC) or sodium cholate (SC). When sodium dodecyl sulfate (SDS) was added to the background electrolyte (BGE) in the absence of the bile salt, a single peak at a migration time longer than that of the EOF was obtained. Substituting the SDS by a bile salt, the homologues were resolved. At the same bile salt concentration, resolution between the homologues was higher with SDC than using SC. Optimum resolution between consecutive homologues was obtained with 50 mM SDC. In the presence of low or moderate amounts of acetonitrile or n-propanol, the background line improved significantly, whereas resolution may increase or decrease slightly. We propose a procedure for the determination of OPEs and NPEs with optimum resolution between the homologues as well as a modified procedure with improved selectivity for the single-run determination of other absorbing nonionic, cationic, and anionic (such as linear alkylbenzene sulfonates) surfactants in industrial and household cleaning products and its application to a variety of samples. The detection limit was ca. 28 microg x mL(-1) of total NPE (n = 10), and peak area repeatabilities at 50 microg x mL(-1) were 1.7% (intraday) and 5.6% (interday).     

Quantitative analysis of malto-oligosaccharides by MALDI-TOF mass spectrometry, capillary electrophoresis and anion exchange chromatography

The analysis of malto-oligosaccharides by MALDI-TOF mass spectrometry (MS), capillary electrophoresis (CE) and anion exchange chromatography with pulsed amperometric detection (HPAEC-PAD) is described. Appropriate methods were developed which enabled the resolution of the oligosaccharides and quantification of the peak areas. It could be shown that each technique provided a different distribution profile of the maltodextrins. Using MALDI-TOF MS signals of higher molecular weight oligomers were enhanced while low molecular weight analogues were discriminated. Thus, the response factor depends on the degree of polymerization (DP) of the carbohydrates. Homologues up to DP-15 could be detected. Analysis of the maltodextrins by CE was accomplished by derivatization of the sugars with 4-aminobenzonitrile (ABN) and 8-aminonaphthalene-1,3,6-trisulfonic acid, respectively. By using the latter reagent oligosaccharides up to DP-13 were detected while derivatization with ABN allowed detection up to DP-9. The molecular weight distribution obtained by both approaches were the same. HPAEC-PAD enabled the determination of oligomers up to DP-9. The distribution obtained by this technique showed somewhat lower signals of the small homologues than those found by CE while the opposite held for higher molecular weight compounds. Hydrolysis of the carbohydrates by the derivatization reaction prior to CE analysis, which increased the proportion of low molecular weight homologues, may account for these findings. Receiverd: 28 August 1997 / Revised: 24 November 1997 / Accepted: 25 November 1997     

Analysis of tensides in complex samples with comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry

Multidimensional gas-chromatographical analysis of various tensides of natural or synthetic origin in cosmetic products is demonstrated. Comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry allows the qualitative and quantitative determination of alkyl polyglucosides (AG), fatty alcohol ethoxylates (FAEO), fatty alcohol sulfates (FAS), fatty alcohol ether sulfates (FAES) and cocamidopropyl betaines (CAPB) in shower gel and cleaning agents. The samples were aliquoted in two parts. The first part was silylated, diluted and analysed; then, in order to detect anionic tensides (FAES, FAS) too, the second aliquot was hydrolysed before being silylated for analysis. Because of their amphoteric character, the betaines can only be analysed by gas chromatography after thermal decomposition in the injector, which leads to the corresponding amidoamines among other products.