Effect of nonisothermality of the surface of a thin profile on the stability of a laminar boundary layer

Investigations of the stability of a subsonic laminar boundary layer have shown that, other things being equal, the stability of the laminar flow is considerably improved by cooling the entire surface of the body to a constant temperature T_w=const lower than the temperature of the free stream [1–3]. This is attributable to an increase in the critical Reynolds number of loss of stability and a decrease in the range of unstable perturbations of the Tollmien-Schlichting wave type when the surface is cooled. Recently, in the course of investigating the stability of laminar flow over a flat plate it was found [4, 5] that a similar improvement in flow stability can be achieved by raising the temperature of a small part of the surface near the leading edge of the plate. In this study we examine the possibility of delaying the transition to turbulent flow by creating a nonuniform temperature distribution along the surface of thin profiles, where the development of an adverse pressure gradient in the outer flow has a destabilizing effect on the boundary layer.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 36–42, September–October, 1986.In conclusion, the authors wish to thank M. N. Kogan for useful discussions of their results.     

Two-phase couette flow

A study is made of plane laminar Couette flow, in which foreign particles are injected through the upper boundary. The effect of the particles on friction and heat transfer is analyzed on the basis of the equations of two-fluid theory. A two-phase boundary layer on a plate has been considered in [1, 2] with the effect of the particles on the gas flow field neglected. A solution has been obtained in [3] for a laminar boundary layer on a plate with allowance for the dynamic and thermal effects of the particles on the gas parameters. There are also solutions for the case of the impulsive motion of a plate in a two-phase medium [4–6], and local rotation of the particles is taken into account in [5, 6]. The simplest model accounting for the effect of the particles on friction and heat transfer for the general case, when the particles are not in equilibrium with the gas at the outer edge of the boundary layer, is Couette flow. This type of flow with particle injection and a fixed surface has been considered in [7] under the assumptions of constant gas viscosity and the simplest drag and heat-transfer law. A solution for an accelerated Couette flow without particle injection and with a wall has been obtained in [6]. In the present paper fairly general assumptions are used to obtain a numerical solution of the problem of two-phase Couette flow with particle injection, and simple formulas useful for estimating the effect of the particles on friction and heat transfer are also obtained.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 42–46, May–June, 1976.     

Effect of surface temperature on the stability of the swept attachment line boundary layer

At fairly high Reynolds numbers instability may develop on the line of attachment of the potential flow to the leading edge of a swept wing and lead to a transition to boundary layer turbulence directly at the leading edge [1, 2]. Although the first results relating to the stability and transition of laminar flow at the leading edge of swept wings were obtained almost 30 years ago, the problem remains topical. The stability of the swept attachment line boundary layer was recently investigated numerically with allowance for compressibility effects [3, 4]. Below we examine the effect of surface temperature on the stability characteristics of the laminar viscous heat-conducting gas flow at the leading edge of a side slipping wing.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 78–82, November–December, 1990.     

Method of mean-mass parameters for a three-dimensional boundary layer in a flow with vorticity

When a gas flows with hypersonic velocity over a slender blunt body, the bow shock induces large entropy gradients and vorticity near the wall in the disturbed flow region (in the high-entropy layer) [1]. The boundary layer on the body develops in an essentially inhomogeneous inviscid flow, so that it is necessary to take into account the difference between the values of the gas parameters on the outer edge of the boundary layer and their values on the wall in the inviscid flow. This vortex interaction is usually accompanied by a growth in the frictional stress and heat flux at the wall [2, 3]. In three-dimensional flows in which the spreading of the gas on the windward sections of the body causes the high-entropy layer to become narrower, the vortex interaction can be expected to be particularly important. The first investigations in this direction [4–6] studied the attachment lines of a three-dimensional boundary layer. The method proposed in the present paper for calculating the heat transfer generalizes the approach realized in [5] for the attachment lines and makes it possible to take into account this effect on the complete surface of a blunt body for three-dimensional laminar, transition, or turbulent flow regime in the boundary layer.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 80–87, January–February, 1981.     

Interaction between the boundary layer and a supersonic flow when part of the wall is rapidly heated

There have been many theoretical studies of aspects of the unsteady interaction of an exterior inviscid flow with a boundary layer [1–9]. The mathematical flow models obtained in these studies by the method of matched asymptotic expansions describe a wide range of phenomena observed experimentally. These include boundary layer separation near the hinge of a flap, the flow in the neighborhood of the trailing edge of an oscillating airfoil [1–2], and the development and propagation of perturbations in a boundary layer excited by an oscillating wall or some other way [3–5]. The present paper studies the interaction of an unsteady boundary layer with a supersonic flow when a small part of the surface of a body in the flow is rapidly heated.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 66–70, January–February, 1984.     

Turbulent flow of a fluid in the neighborhood of the trailing edge of a plate at zero angle of attack

The laminar flow regime of an incompressible fluid at the trailing edge of a plate was studied by Stewartson and Messiter [1, 2] by means of the method of matched asymptotic expansions. In. the present paper, this method is used to analyze the same problem, but in the case of turbulent flow in the boundary layer and the wake. A system of linear equations of elliptic type with variable coefficients is obtained for the averaged values of the flow parameters in the main part of the boundary layer and the wake that is responsible for the change in the displacement thickness. A solution of this system is constructed by the Fourier method in the case of a power law of the velocity in front of the interaction region.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 17–23, November–December, 1983.     

Excitation of Tollmien-Schlichting waves py a vibrating section of a surface with flow round it

In the context of the problem of describing the transition of a laminar boundary layer to a turbulent, great interest attaches to the study of susceptibility, i.e., of the reaction of the flow to various external influences, such as acoustic perturbations, surface roughness, vibration of the wall, turbulence of the unperturbed flow, etc. A general property of the effect of the factors mentioned above on the flow in a laminar boundary layer was discovered in experimental and numerical studies and is noted in [1]: in all cases an external forcing perturbation leads to the excitation of normal modes of oscillation in the boundary layer which propagate downstream, namely, Tollmien-Schlichting waves. There is an analytical calculation in [2, 3] of the amplitude of a wave excited by harmonic oscillations of a narrow band on the surface of a plane plate, the Reynolds number having been assumed to be infinitely large, and the frequency of the vibrator corresponding to the neighborhood of the lower branch of the neutral cuirve [4], In [5] the amplitude of the wave of instability generated is calculated by the method of expansion of the solution in a biorthogonal system of eigenfunctions. The amplitudes of the Tollmien-Schlichting waves are calculated below by means of a generalization of the method of [2] for the whole range of Reynolds numbers and frequencies of the vibrator corresponding to the region of instability: for moderate Reynolds numbers the problem is solved numerically, while for large Reynolds numbers an asymptotic solution is constructed.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 4, pp. 46–51, July–August, 1987.The author is grateful to M. N. Kogan and V. V. Mikhailov for useful discussions of the results of the study.     

Stability of laminar boundary layer on an elastic surface in an incompressible fluid

Interest in the present problem arose after the publication of the results of the experiments of Kramer [1–3]. In addition to the studies indicated in [4], the articles [5–8] are devoted to the question of the interaction of a flexible elastic surface with the boundary layer. In the present paper the problem of the interaction of an elastic surface with disturbances arising in the boundary layer is posed as in [4]. The approximate nature of the methods of solving the problem of the hydrodynamic stability of the laminar boundary layer leads to a difference in the final computational formulas even in the case when authors use the same Heisenberg-Tollmien-Schlichting-Lin scheme. Therefore, in what follows we present a comparison of the data on the stability of the boundary layer on a solid wall obtained by several authors with the calculations using the formulas, which are then generalized to the case of the elastic surface.The author wishes to thank G. I. Petrov and V. A. Medvedev for discussions of the present study.     

Development of the boundary layer on a plate in a rotating system

A numerical investigation in the approximation of boundary layer theory has been made of the development of the flow near the surface of a rotating plate in a two-dimensional flow with rectilinear streamlines perpendicular to the leading edge in a rotating coordinate system attached rigidly to the plate. In an earlier investigation [1] using the approximate method of integral relations, Kurosaka obtained and described quantitatively a transition from a Blasius boundary layer to an Eckmann boundary layer in the form of three-dimensional oscillations. The solution described in the present paper confirms the oscillatory nature of the development of the boundary layer, but the quantitative results differ strongly from Kurosaka's.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 154–157, May–June, 1982.     

Stability of preseparation boundary layer on the leading edge of a thin airfoil

Numerous experiments on subsonic flow of gas past thin wing profiles (see the reviews [1, 2]) have shown that the flow near the leading edge of an airfoil is separationless only at angles of attack less than a certain critical value, which depends on the shape of the airfoil. If the angle of attack reaches the critical value, a closed region of recirculation flow of small extension is formed on the upper surface of the airfoil. Under ordinary flow conditions, the boundary layer on the leading edge of the airfoil remains laminar in the entire preseparation range of angles of attack. However, the appearance of the closed separation region is, as a rule, accompanied by transition from a laminar to a turbulent flow regime. Moreover, generation of turbulence is observed precisely in the flow separation region. The present paper is devoted to a study of the stability of the boundary layer on the leading edge of a thin airfoil in a flow of incompressible fluid. The case when the angle of attack of the airfoil relative to the oncoming flow differs little from the critical value is considered.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 55–63, November–December, 1982.     

Computational analysis and flow structure of a transitional separated-reattached flow over a surface mounted obstacle and a forward-facing step

Large-eddy simulation (LES) of transitional separating-reattaching flow on a two-dimensional square surface mounted obstacle and a forward facing step has been performed using a dynamic sub-grid scale model. The Reynolds number based on the uniform inlet velocity and the obstacle/step height is 4.5 × 10³. The mean LES results for both the obstacle and step flow compare reasonably well with the available experimental and DNS data.

The flow structures upstream of the surface-mounted obstacle (referred to hereafter as obstacle) and the forward-facing step (referred to hereafter as FFS) consist of unstable two-dimensional structures and coherent rib-shaped structures. These structures with the aid of 3D streamline visualisation strongly indicate that the upstream separation bubble is a closed one rather than an open one in the sense that there is little evidence to suggest that there is fluid injection from the upstream separation region into the downstream separated region for the two geometries. The spectra and time history for the velocities and pressure fields at locations immediately upstream of the obstacle and FFS (including the recirculation region) were analysed using both the Fourier and wavelet transforms and revealed the unsteady nature of the recirculation region upstream of the obstacle and FFS.

The transition process has been elucidated using both 2D and 3D flow visualisation of the flow. In both geometries (obstacle and FFS), the separated boundary layer downstream of the leading edge shows 2D nature and roll-up shortly downstream of the separation line leading to 2D K-H rolls to be shed from the leading edge. Coherent structures such as the λ-shaped and rib-like vortices commonly associated with a flat plate boundary layer and also found in the separated-reattached flow of a blunt leading edge plate aligned horizontally to a flow are not common in the separated-reattached flow over the obstacle and FFS.     

Laminar boundary layer stability on membrane type deformable surfaces

In connection with the successful experiments of Kramer [l, 2] on models sheathed by flexible coverings, attempts have been made to explain theoretically the effect of boundary deformation on the position of the point of stability loss in the boundary layer. Korotkin [3] examined the stability of a plane laminar boundary layer on an elastic surface under the assumption of a linear connection between the pressure perturbation and the normal deformation of the surface. Benjamin [4] and Landahl [5] investigated the stability of the laminar boundary layer on a membrane type surface under the assumption that the physical characteristics of the surface depend on the perturbing flow wavelength. In the following we examine stability of Blasius flow on a membrane type surface whose physical characteristics are constant along the length.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, vol. 10, no. 6, pp. 52–56, November–December, 1969.     

Laminar boundary layer with uniform suction on flat plate in oscillating flow

We examine unsteady incompressible fluid flow in a laminar boundary layer with uniform suction for longitudinal flow over a flat plate when the external stream is a flow with constant velocity, on which there is superposed a sinusoidal disturbance convected by the stream, analogous to [1]. We study the stability of such flow in the boundary layer.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, Vol. 11, No. 3, pp. 66–70, May–June, 1970.     

Laminar heat transfer near an asymmetric stagnation point

This paper considers the laminar boundary layer at an obstacle near the stagnation point of a three-dimensional incompressible potential flow, asymmetric with respect to this point (e.g., for a jet incident at an angle on an obstacle). The effect of compressibility is investigated in the example of a plane subsonic flow. The solution in the close vicinity of the stagnation point is obtained by expanding in series with respect to the longitudinal coordinate, and for the more distant vicinity, the problem is solved by the method of local similarity. It is shown that in this case (in contrast with a symmetric flow [1, 2]) the maximum heat flux does not coincide with the stagnation point.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 140–145, November–December, 1976.The author thanks V. V. Lunev for stating the problem and for scientific guidance.     

Mechanism of compressor airfoil boundary layer flow control using nanosecond plasma actuation

The flow control effects of nanosecond plasma actuation on the boundary layer flow of a typical compressor controlled diffusion airfoil are investigated using large eddy simulation method. Three types of plasma actuation are designed to control the boundary layer flow, and two mechanisms of compressor airfoil boundary layer flow control using nanosecond plasma actuation have been found. The plasma actuations located within the laminar boundary layer flow can induce a small vortex structure through influencing on the density and pressure of the flow field. As the small vortex structure moves downstream along the blade surface with the main flow, it can suppress the turbulent flow mixing and reduce the total pressure loss. The flow control effect of the small vortex structure is summarized as wall jet effect. Differently, the plasma actuation located within the turbulent boundary layer flow can act on the shear layer flow and induce a large vortex structure. While moving downstream, this large vortex structure can suppress the turbulent flow mixing too.     

Disturbance evolution in the leading-edge region of a blunt flat plate in supersonic flow

The spatio-temporal dynamics of small disturbances in viscous supersonic flow over a blunt flat plate at freestream Mach number M_∞=2.5 is numerically simulated using a spectral approximation to the Navier–Stokes equations. The unsteady solutions are computed by imposing weak acoustic waves onto the steady base flow. In addition, the unsteady response of the flow to velocity perturbations introduced by local suction and blowing through a slot in the body surface is investigated. The results indicate distinct disturbance/shock-wave interactions in the subsonic region around the leading edge for both types of forcing. While the disturbance amplitudes on the wall retain a constant level for the acoustic perturbation, those generated by local suction and blowing experience a strong decay downstream of the slot. Furthermore, the results prove the importance of the shock in the distribution of perturbations, which have their origin in the leading-edge region. These disturbance waves may enter the boundary layer further downstream to excite instability modes.     

Supersonic flow around the trailing edge of a thin profile

The method of mergeable asymptotic expansions has recently been used effectively in investigations devoted to the study of boundary layer interaction with an external inviscid flow at high subcritical Reynolds numbers Re. The asymptotic analysis permits obtaining a limit pattern of the flow around a solid as Re þ, and determining the similarity and quantitative regularity laws which are in good agreement with experimental results. Thus by using the method of mergeable asymptotic expansions it is shown in [1–4] that near sites with high local curvature of the body contour and flow separation and attachment points, an interaction domain appears that has a small length on the order of Re^-3/8. In this flow domain, which has a three-layer structure, the pressure distribution in a first approximation already depends on the change in boundary-layer displacement thickness, while the induced pressure gradient, in turn, influences the flow in the boundary layer. An analogous situation occurs in the neighborhood of the trailing edge of a flat plate where an interaction domain also appears [5, 6]. The flow in the neighborhood of the trailing edge of a flat plate around which a supersonic viscous gas flows was examined in [7]. Numerical results in this paper show that the friction stress on the plate surface remains positive everywhere in the interaction domain, and grows on approaching the trailing edge. The supersonic flow around the trailing edge of a flat plate at a small angle of attack was investigated in [8, 9], Supersonic flow of a viscous gas in the neighborhood of the trailing edge of a flat plate at zero angle of attack is examined in [10], but with different velocity values in the inviscid part of the flow on the upper and lower sides of the plate. The more general problem of the flow around the trailing edge of a profile with small relative thickness is investigated in this paper.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 3, pp. 36–42, May–June, 1981.     

Asymptotic analysis of the equations of a three-dimensional boundary layer

The asymptotic solutions of the self-similar equations of two- and three-dimensional boundary layers have been investigated by many authors (see, for example, [1–3]). In [4, 5], asymptotic solutions were found for non-self-similar equations for two-dimensional flow, and the propagation of perturbations near the external edge of the boundary layer was analyzed. In the present paper, asymptotic solutions are obtained for the non-self-similar equations of a three-dimensional laminar boundary layer of an incompressible fluid. It is shown that the conclusion drawn in [5] — that the boundary conditions can be transferred from infinity to a finite distance from the wall — is also true for three-dimensional flow. The obtained solutions explain the experimentally well-known phenomenon of the conservativeness of the secondary currents. The essence of this phenomenon is that a change in the sign of the transverse (along the normal to a streamline of the external flow) pressure gradient is accompanied by a very rapid change in the direction of the secondary flow near the wall, whereas in the upper layers of the boundary layer the direction remains unchanged for a substantial time.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 155–157, September–October, 1979.     

Structure of the flow of a viscous gas near the trailing edge of a flat plate

Solution of the complete system of Navier-Stokes equations forms the basis for a study of the nature of flow of a viscous heat-conducting gas in the neighborhood of a trailing edge of a flat plate. The problem was solved in accordance with a difference scheme of the third order of accuracy [1]. The calculation was carried out under the same conditions as the experiment of [2], in which a plate of finite dimensions (L = 12 cm) had supersonic M = 2, Re, = 1000 gas flow round it. In order to obtain a thickness of the boundary layer which was acceptable for the purpose of making the measurements (of the order of 2 cm), the unperturbed gas was slightly rarefied. In the study of such problems [3–7] it is necessary to use the complete system of Navier-Stokes equations, since in the immediate neighborhood of the trailing edge one of the important assumptions in the theory of the boundary layer, ²u/y^{2 2}u/x², does not hold. As a result the flow upstream near the trailing edge of the plate will depend on the flow immediately behind the edge, since the perturbations propagate both upstream and downstream in this case. The rarefaction of the gas creates additional difficulties in the formulation of the boundary conditions on the plate with flow round it when this problem is studied numerically.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 27–30, March–April, 1987.     

Flow instability in the laminar boundary layer separation zone created by a small roughness element

The development of disturbances of the laminar flow in the separation zone behind a surface projection in the boundary layer on a flat plate has been experimentally investigated. The linear instability characteristics of the separated flow are determined and the interaction between the oscillations growing in the separation zone and the average flow is studied.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 16–22, January–February, 1990.