Synthesis, characterization and potential biomedical applications of N-succinimidyl ester functionalized, polypyrrole-coated polystyrene latex particles

N-Succinimidyl ester functionalized polypyrrole-coated polystyrene latex particles (PS_E-PPyNSE) were prepared by the in situ copolymerization of pyrrole and the active ester-functionalized pyrrole (pyrrole-NSE) in the presence of polystyrene latex particles. Polystyrene microspheres were prepared by emulsion polymerization (PS_E) leading to particles having a diameter of 450 nm. These PS_E particles were precoated with poly(N-vinylpyrrolidone) prior to the in situ copolymerization of pyrrole and pyrrole-NSE. The initial comonomer concentration fractions were 25/75, 50/50 and 75/25 for pyrrole and pyrrole-NSE, respectively. The PPy-coated PS_E particles were characterized in terms of morphology, particle size, electrophoretic mobility and chemical composition. The study of morphology by means of scanning electron microscopy showed roughening of the underlying PS_E particles owing to the addition of PPyNSE, the overlayer thickness of which was estimated to be around 7 nm. Moreover, loading PPyNSE overlayers resulted in a shift of the electrophoretic mobility from –5.31 m cm/V s to a very small but positive value (0.082–0.112 m cm/V s). X-ray photoelectron spectroscopy and IR spectroscopy permitted the detection of pyrrole-NSE repeat units at the surface indicating that pyrrole and pyrrole-NSE did indeed copolymerize. The PS_E-PPyNSE particles were further evaluated as bioadsorbents of human serum albumin used as a test protein. For this study, PS_E-PPyNSE₅₀ particles, synthesized from a comonomer feed ratio of 50/50 in pyrrole/pyrrole-NSE, were used and were shown to attach efficiently human serum albumin macromolecules with a maximum amount of 0.2 mg m^–2.

Preparation of monodisperse ellipsoidal polystyrene particles

A method is described for the preparation of monodisperse ellipsoidal particles of polystyrene in the colloidal size range. Monodisperse polystyrene particles were dispersed in a solution of polyvinyl alcohol. This dispersion was then allowed to form, by evaporation, a thin film of polyvinyl alcohol containing spherical polystyrene particles. Strips of this film were clamped into a metal frame, heated rapidly in an oil bath to 200°C and stretched to a predetermined extent in order to convert the spherical particles into ellipsoids; the film was then cooled. A wide range of axial ratios for a variety of initial particle sizes was obtained by this method.     

Preparation and characterization of micron-sized polystyrene/polysiloxane core/shell particles

A procedure has been developed to coat micron-sized polystyrene (PS) spheres with a smooth layer of polysiloxane by a sol–gel process of methyl trimethoxylsilane (MTMS) without using silane coupling agents. The thickness of the shells can be easily varied with different polystyrene seeds and methyl trimethoxysilane feed ratio. When we used PS particles with diameters of 2.09 μm prepared by conventional dispersion polymerization as seeds, the thickness of the polysiloxane shells can be varied from 0.11 to 0.21 μm. The particle size, size distribution, thermal decomposition, and solvent resistance were investigated by scanning electron microscope (SEM), transmission electron microscope (TEM), size analyzer, and TG, respectively.     

Synthesis of ZnO/polystyrene composites particles by Pickering emulsion polymerization

ZnO/polystyrene composite particles were synthesized by Pickering emulsion polymerization. ZnO nanoparticles were first prepared by reaction of zinc acetate and sodium hydroxide in ethanol medium. Then different amount of styrene monomer was emulsified in water in the presence of ZnO nanoparticles either by mechanical stirring or by sonication, followed by polymerization of styrene. Two kinds of initiators were used to start the polymerization, azobisisobutyronitrile (AIBN) and potassium persulfate (KPS). The X-ray diffraction pattern verified the crystal structure of ZnO and FT-IR spectra evidenced the existence of ZnO and polystyrene (PS) in ZnO/polystyrene composite particles. Different morphologies were observed for the composite particles when using different initiators. From TEM photographs, AIBN-initiated system produced mainly core-shell composite particles with PS as core and ZnO as shell, while KPS-initiated system showed both composite particles and pure PS particles. Two schemes of reaction mechanism were proposed to explain the morphologies accordingly. Both systems of composite particles showed good pH adjusting ability.     

Preparation of non-contact ordered array of polystyrene colloidal particles by using a metallic thin film of fused hemispheres

A thin metallic bilayer consists of fused hollow hemispheres of 930 nm in diameter is fabricated by sputter deposition of Ti and Fe at 50 and 5 nm of thickness, respectively, onto an array of spherical polystyrene colloidal particles. The fused metal hemispheres are utilized to assemble polystyrene colloidal particles of smaller diameters (800 nm) into non-contact two-dimensional periodic array by trapping them in the metallic wells.     

Experimental study of short- and long-time diffusion regimes of spherical particles in carboxymethylcellulose solutions

The behavior of latex particles in carboxymethylcellulose (CMC) solutions with different probe radii and solution concentrations is investigated. The diffusion processes of probe particles are studied by means of dynamic light scattering experiments. The existence of two diffusion regimes (a short-time regime and a long-time regime) is established for concentrations higher than the threshold value which changes for each probe dimension. Information is also provided about the relative weight of the probe population undergoing the two diffusion processes. This experimental evidence is discussed in connection with the existence of a defined volume (cage) in which short-time diffusion is the characteristic motion, while the long-time diffusion process dominates the motion over all the cages. Furthermore, there was found to be some deviation from Stokes-Einstein behavior.     

Void closure and interdiffusion processes during latex film formation from surfactant-free polystyrene particles: a fluorescence study

This study reports a steady state fluorescence (SSF) technique for studying film formation from surfactant-free polystyrene (PS) latex particles. The latex films were prepared from pyrene (P)-labeled PS particles at room temperature and annealed at elevated temperatures for 5-, 10-, 20-, and 30-min time intervals above the glass transition (T(g)) temperature of polystyrene. During the annealing processes, the transparency of the film changed considerably. Scattered light (I(sc)) and fluorescence intensity (I(0P)) from P were measured after each annealing step to monitor the stages of film formation. Evolution of transparency of latex films were monitored using photon transmission intensity, I(tr). Scanning electron microscopy (SEM) was used to detect variation in the physical structure of annealed films. Onset temperature for film formation, T(0), void closure, T(v), and healing temperatures, T(h), were determined and corresponding activation energies were measured. Void closure and interdiffusion stages were modeled and related activation energies were determined.     

Preparation and characterization of core-shell polystyrene/polychloromethylstyrene and hollow polychloromethylstyrene micrometer-sized particles of narrow-size distribution

Polystyrene core microspheres of narrow-size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2-methoxy ethanol. Polystyrene/polychloromethylstyrene and polystyrene/poly(chloromethylstyrene-divinylbenzene) core-shell microspheres of narrow-size distribution were prepared by seeded emulsion polymerization of chloromethylstyrene or chloromethylstyrene and divinylbenzene in the presence of the polystyrene core microspheres at 71 °C. Core-shell particles with different properties (size, surface morphology, and composition) have been prepared by changing various parameters belonging to the emulsion polymerization process, e.g., volume of the chloromethylstyrene and the volume ratio of chloromethylstyrene to divinylbenzene. Dissolution of the polystyrene core of the polystyrene/poly(chloromethylstyrene-divinylbenzene) core-shell particles resulted in the formation of crosslinked hollow polychloromethylstyrene microspheres, broken crosslinked polychloromethylstyrene shells, or particles containing voids, depending on the composition of the polystyrene/poly(chloromethylstyrene-divinylbenzene) particles.     

Dye-sensitized solid-state solar cells fabricated by screen-printed TiO_2 thin film with addition of polystyrene balls

The screen-printed nanoporous TiO2 thin film was employed to fabricate dye-sensitized solid-state solar cells using CuI as hole-transport materials. The solar cell based on nanoporous TiO2 thin film with large pores formed by the addition of polystyrene balls with diameter of 200 nm to the TiO2 paste exhibits photovoltaic performance enhancement, which is attributed to the good contact of CuI with surface of dye-sensitized thin film due to easy penetration of CuI in the film with large pores.     

Preparation and properties of a thermo-sensitive latex film

Polymer particles with hydrophobic core and hydrophilic shell were prepared via a three-step method. First, poly(butyl methacrylate-co-methyl methacrylate) (p-(BMA-MMA)) latex was prepared through emulsion polymerization. Then, a shell of poly(glycidyl methacrylate) (p-GMA) was introduced around the p-(BMA-MMA) particles by using a redox initiation system under kinetically controlled conditions. Finally, part of the epoxy groups existing in the shell were converted into quaternary ammonium salts, resulting in an ionic hydrophilic shell. The core-shell particles could be redispersed in water to form a stable emulsion. The contact angle of the core-shell latex film with water was around 16° at 25 °C, which became larger than 90° after the film was heated at 150 °C for a short period of time. This showed that the latex film was completely switched from hydrophilicity to hydrophobicity by the action of heat. Additionally, the latex film before heat treatment could be easily washed away from the substrate with neutral water, but it could no longer be removed after the heat treatment. When an IR dye with the maximum absorption at 830 nm was incorporated into the film, it became sensitive to LD laser emitting at 830 nm and gave negative image after exposed by LD laser and developed with neutral water. This showed that the latex film might find uses in chemical-free thermal laser imaging applications.     

Early-stage flocculation kinetics of polystyrene latex particles with polyelectrolytes studied in the standardized mixing: Contrast of excess and moderate polyelectrolyte dosage

Standardized mixing procedure was applied to the analysis of flocculation of polystyrene latex (PSL) particles with polyelectrolytes. After confirming the initial enhancement of flocculation rate in the very beginning followed by abrupt stop with excess dosage, attention was shifted to the system of moderate dosage. In the former, effects of ionic strength were further analyzed to find the consistency with adsorption isotherm. In the latter, flocculation started slowly in the beginning, sometime slower than salt-induced rapid coagulation, however, the rate gradually increases in the middle stage. Often, the increased rate exceeds that of salt-induced rapid coagulation. This behavior emerged more clearly in the case of lower ionic strength. This is the indication that the rate of relaxation of polymer on the colloidal surface is a function of surface coverage and ionic strength. The ultimate degree of flocculation is usually higher than that observed for excess dosage. The size distribution of flocs was also examined, however, no clear difference between different experimental conditions was confirmed for the same degree of flocculation.     

Electrospun polystyrene/graphene nanofiber film as a novel adsorbent of thin film microextraction for extraction of aldehydes in human exhaled breath condensates

In the current study, we introduced a novel polystyrene/graphene (PS/G) composite nanofiber film for thin film microextraction (TFME) for the first time. The PS/G nanofiber film was fabricated on the surface of filter paper by a facile electrospinning method. The morphology and extraction performance of the resultant composite film were investigated systematically. The PS/G nanofiber film exhibited porous fibrous structure, large surface area and strong hydrophobicity. A new thin film microextraction-high performance liquid chromatography (TFME-HPLC) method was developed for the determination of six aldehydes in human exhaled breath condensates. The method showed high enrichment efficiency and fast analysis speed. Under the optimal conditions, the linear ranges of the analytes were in the range of 0.02–30 μmol L⁻¹ with correlation coefficients above 0.9938, and the recoveries were between 79.8% and 105.6% with the relative standard deviation values lower than 16.3% (n = 5). The limits of quantification of six aldehydes ranged from 13.8 to 64.6 nmol L⁻¹. The established method was successfully applied for the quantification of aldehyde metabolites in exhaled breath condensates of lung cancer patients and healthy people. Taken together, the TFME-HPLC method provides a simple, rapid, sensitive, cost-effective, non-invasion approach for the analysis of linear aliphatic aldehydes in human exhaled breath condensates.     

Dispersion stability and rheological behavior of suspensions of polystyrene coated fumed silica particles in polystyrene solutions

Polystyrene coated silica（SiO₂@PS） core-shell composite particles with averaged diameter of about 290 nm were prepared by in situ emulsion polymerization of styrene on the surface ofγ-methacryloxypropyltrimethoxysilane grafted SiO₂ nanoparticles of 20-50 nm in diameter.Rheological behavior and dispersion stability of SiO₂@PS suspension in 10 wt%PS solution were compared with suspensions of untreated SiO₂ and silane modified SiO₂ nanoparticles.Suspensions of the untreated and the silane modified SiO₂ exhibited obvious shear thinning.The SiO-2@PS suspension exhibits shear viscosity considerably smaller than suspensions of untreated and silane modified SiO₂ at low shear rates.Transmission electron microscopy showed that the composite particles can uniformly and stably disperse in PS solution compared to other suspensions,implying that the PS shell can effectively enhance the particle compatibility with PS macromolecules in solution.     

Automated analysis of individual particles using a commercial capillary electrophoresis system

Capillary electrophoretic analysis of individual submicrometer size particles has been previously done using custom-built instruments. Despite that these instruments provide an excellent signal-to-noise ratio for individual particle detection, they are not capable of performing automated analyses of particles. Here we report the use of a commercial Beckman P/ACE MDQ capillary electrophoresis (CE) instrument with on-column laser-induced fluorescence (LIF) detection for the automated analysis of individual particles. The CE instrument was modified with an external I/O board that allowed for faster data acquisition rates (e.g. 100 Hz) than those available with the standard instrument settings (e.g. 4 Hz). A series of eight hydrodynamic injections expected to contain 32 +/- 6 particles, each followed by an electrophoretic separation at -300 V cm(-1) with data acquired at 100 Hz, showed 28 +/- 5 peaks corresponding to 31.9 particles as predicted by the statistical overlap theory. In contrast, a similar series of hydrodynamic injections followed by data acquisition at 4 Hz revealed only 8 +/- 3 peaks suggesting that the modified system is needed for individual particle analysis. Comparison of electropherograms obtained at both data acquisition rates also indicate: (i) similar migration time ranges; (ii) lower variation in the fluorescence intensity of individual peaks for 100 Hz; and (iii) a better signal-to-noise ratio for 4 Hz raw data. S/N improved for 100 Hz when data were smoothed with a binomial filter but did not reach the S/N values previously reported for post-column LIF detection. The proof-of-principle of automated analysis of individual particles using a commercially available CE system described here opens exciting possibilities for those interested in the study and analyses of organelles, liposomes, and nanoparticles.     

Dielectrophoretic investigation of plant virus particles: Cow Pea Mosaic Virus and Tobacco Mosaic Virus

This paper reports experimental results on the dielectrophoretic (DEP) behaviour on two nonenveloped plant viruses of different geometrical shapes, namely Cow Pea Mosaic Virus (CPMV) and Tobacco Mosaic Virus (TMV). The DEP properties of carboxy-modified latex beads of the same size are also reported. The DEP properties of single particles were obtained from measurement of the frequency at which the DEP force on a particle goes to zero (the crossover frequency). The DEP behaviour of particle ensembles was also measured using image processing. The dielectric properties of the particles were evaluated from the DEP data. The surface conductance was found to be 0.3 nS for CPMV, 0.38 nS for TMV, and 0.52 nS for 27 nm diameter carboxy-latex beads. Data analysis has shown that the optimal condition for separation of TMV and CPMV is a low-conductivity suspending medium - below 1 mS/m.     

Synthesis of temperature responsive polymer brushes from polystyrene latex particles functionalized with ATRP initiator

Thermally responsive poly(N-isopropylacrylamide) (PNIPAAM) brushes were grafted from polystyrene particles synthesized with surfactant free emulsion polymerization and functionalized with a thin shell of ATRP initiator on the surface. The ATRP initiator was present in the shell either alone or along with copolymerized styrene and also a crosslinker. The grafted brushes were characterized with transmission electron microscopy before and after negative staining with uranyl acetate. Cryo-scanning electron microscopy confirmed the growth of extremely long PNIPAAM layers from the surface, which otherwise looked shrunken in the transmission electron microscope owing to dehydration and possibly the effect of staining agent. The amount of grafted polymer also increases proportionally to the increase of the monomer concentration in the initial reaction system. The change in character from hydrophilic to hydrophobic with temperature and salt was found to be reversible and fast. The adsorption of protein complexes (tobacco mosaic virus) could be readily achieved at higher temperatures indicating the potential of the grafted particles to be used as stationary phases in temperature regulated chromatographic separations.     

Highly efficient formation of metal and metal alloy particles from methyl metal compounds by a single pulse laser irradiation

Highly efficient processes for fine particle formation of metal alloys and metal oxides were developed using a high-power laser. In these processes, laser light was used only for the ignition of a thermal chain reaction. This reaction was suppressed by adding inert gases, and the suppression effect was in the order C₃H₈ > C₂H₆ > CH₄ > He > Ar > Xe. Oxygen accelerated the reaction because of the large exothermicity of the reaction of oxygen with methyl metal compounds.     

On the morphology of polystyrene fractions,obtained by a multistep procedure from a radically polymerized sample

Summary A polystyrene sample obtained by free radical polymerization has been fractionated by preparative scale GPC and the structure and morphology of the fractions have been studied by¹³C-NMR spectroscopy, DSC and X-ray measurements. No changes in morphology in the course of fractionation have been obeyed. A distribution of syndiotacticity within the molecular weight distribution does not exist.

---

Zusammenfassung Eine Polystyrolprobe, die durch radikalische Polymerisation hergestellt wurde, wurde mit Hilfe der präparativen Gelpermeationschromatographie fraktioniert; die Struktur und Morphologie der Fraktionen wurde mit¹³C-NMR-Spektroskopie, DSC und Röntgenbeugung untersucht. Im Verlauf der Fraktionierung traten keine Änderungen der Morphologie der Fraktionen auf. Innerhalb der Molekulargewichtsverteilung existiert keine Verteilung der Syndiotaktizität.

---

List of abbrevations and symbols AIBN a, a-Azo-bis-(iso-butyronitrile) - D Dispersity, M _w /M _n - DSC Differential scanning calorimetry - EF Efficiency of fractionation - GPC Gel permeation chromatography - m mass of the fraction - M mass of the fractionated polymer sample - MWD Molecular weight distribution - P _r content of racemic dyads - PS Polystyrene - THF Tetrahydrofuran - U D-1 - U _ss U of the starting sample - U _f U of the fraction Auszug aus der Dissertation von U.-D. Standt: Zur Morphologie von Polystyrol, TU Braunschweig 1981.