PET/PC共混体系结晶行为研究进展

聚对苯二甲酸乙二醇酯(PET)／聚碳酸酯(PC)合金材料是综合性能优异的工程塑料,对其结晶行为的研究,可为设计,调节及控制材料的性能提供理论基础。评述了近年来PET／PC共混体系结晶行为研究的最新工作和理论进展,包括PET／PC共混体系酯交换、相容性及结晶性的关系,退火对PET／PC共混体系结晶行为的影响,第三组分对PET／PC共混体系结晶行为的影响,PET／PC共混体系结晶动力学以及PET／PC共混体系高压结晶行为的研究。并对今后的深入研究作了展望。     

PET/PEN/DBS共混体系结构与形貌的研究

共混是改善聚合物性能的一种简单而又行之有效的方法,PET和PEN均为结晶性聚酯,由于PEN合成原料的影响,致使PEN的价格较高,但性能比PET优良,通过二者的共混,既可以提高PET的性能,又可以降低PEN成本,有关PET／PEN共混体系的研究已引起人们的关注,而对于共混体系结晶形态和结晶条件的研究较少,由于成核剂能够提高结晶速率,减小球晶尺寸,因此本文对PET／PEN／DBS共混体系中,组分组成的影响及不同结晶条件下共混物的结晶形貌进行研究。     

对羟基苯甲酸(PHB)聚对苯二甲酸乙二酯(PET)液晶共聚酯和聚对苯二甲酸乙二酯共混物的酯交换表征

在温度280℃附近对含有液晶共聚酯P-Hydroxy Benzoic Acid/Poly(-Ethylene Terephthalate-)PHB/PET和Poly(-Ethylene Terephthalate-)PET的共混样品进行热处理时,发现共混物的熔点随热处理的时间增加而不断降低,热处理温度越高,相同时间内共混物熔点下降程度越大;而具有相同热历史的纯PET样品熔点几乎保持不变.通过NMR方法证实了PHB/PET-TET共混物熔点随热处理时间下降是由于PHB/PET和PET之间发生了酯交换反应.所以可根据共混物的宏观热性质和PHB/PET序列结构变化表征PHB/PET和PET共混物之间的酯交换程度.     

PET分子量对PET/PC共混体系高压结晶行为的影响

以往高压合成的聚合物伸直链晶体尺寸较小且合成时间过长,不能满足单晶应用的要求。加入10wt%PC于不同分子量的PET中,采用自制高压装置,制备共混体系,用WAXD,SEM,DSC等表征手段,研究了PET/PC共混体系在高压下的结晶行为。研究结果表明:通过PET/PC体系在高压下化学反应诱导的自组装,不同分子量PET的PET/PC共混体系均在较短的时间内生成了尺寸较大的聚酯伸直链晶体,对应于三斜晶系,其中PET/PC体系最适于大尺寸伸直链晶体的合成,仅需6hr时间即生成PE需200hr方可合成的40μm厚度的伸直链晶体。同时提出了PET1/PC体系中伸直链晶体高温下缺陷自我修复模型。     

PET/PEN共混体系结构与性能研究进展

综述了国内外PET/PEN共混体系的研究进展,重点论述了PET/PEN共混体系的结晶性能相容性酯交换影响因素、结晶动力学,并对其应用前景做了展望.     

聚对苯二甲酸乙二醇酯和聚碳酸酯共混物的形态结构研究

本文利用偏光显微镜、X-射线衍射仪和示差扫描量热计研究了PET/PC共混物的形态结构。结果表明,在PET/PC共混物中,PC含量在50％以下时,PC的晶粒与PET的球晶分别分散在非晶区中,当PC的含量在50％以上时,PET的晶粒与PC的晶粒分别分散在非晶区中,随着PC含量的增加,PET晶体的完整性被破坏,晶粒变小,结晶度下降,熔点降低。     

PET/PEN共混物的相容性与酯交换反应

通过用1H-NMR对聚对苯二甲酸乙二酯(PET)与聚2,6-萘甲酸乙二酯(PEN)、PET/PEN共聚物的共混物酯交换反应的研究,测得了反应速率常数、反应活化能和诱导期.根据酯交换反应程度和不同反应温度下的诱导期探讨了酯交换反应与相容性的关系,认为PET与PEN的相容导致或增强了酯交换反应,即相容性是酯交换的必要条件;同时酯交换的发生又促进了PET与PEN的相容.酯交换和相容是聚酯共混物熔融时相互关联的两个过程.     

PET/LCP反应性共混物的非等温结晶动力学

采用DSC方法研究了聚对苯二甲酸乙二酯 (PET)和热致性液晶共聚酯 6 0PHB PET (LCP)体系在少量扩链剂双 (2 唑啉 ) (BOZ)存在下形成的反应性共混物的非等温结晶动力学 .结果表明反应性共混物的Avrami指数均在 3 0～ 4 5之间 ,BOZ的加入使反应共混物中PET组分的结晶速率降低 ;表明BOZ对酯交换的促进作用 ,使所生成的共聚酯中PET嵌段的数均序列长度变短 ,而使结晶在某种程度上较为困难 ,但对体系的成核和结晶生长机理无明显影响 .结果还表明 ,随冷却速率的增大结晶峰向低温方向移动     

高特PET-PBT共混单丝的结构与性能

采用一定比例的聚对苯二甲酸丁二醇酯(PBT)对聚对苯二甲酸乙二醇酯(PET)进行共混改性纺制大直径单丝,通过对共混单丝的力学性能、扫描电子显微镜及热性能分析,研究了共混比例、后拉伸工艺对共混物的相容性和拉伸强度的影响.结果表明:通过PET-PBT共混,提高了单丝的勾结强度;液体冷却温度、拉伸倍率及拉伸温度是影响共混单丝...     

PC/PET/EPDM共混体系的结晶与熔融行为

本文用解偏振光法与DSC法分别测定并研究了PC/PET/EPDM共混体系的结晶速度、结晶度、Avrami指数(n)和熔融温度及其影响因素,共混物中PET的结晶速度、结晶度均随PC含量增加而下降;EPDM用量不超过10%时,可提高PET的结晶速度,但不影响结晶度和成核与增长方式,n值不变。当EPDM为5%时,结晶速度呈现极大值。经退火处理的共混物呈现熔融双峰,PC量增加,高温熔融峰略移向高温方向;热处理温度升高或时间延长,则低温熔融峰移向高温方向。     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

氢气在炭狭缝微孔内吸附的预测

通过边界的平均场近似,推导二平板狭缝孔格子理论Ono-Kondo吸附等温方程.利用格子气模型特性和微观物理学理论,计算氢分子在石墨平面的最大吸附容量.比较由氢分子在石墨平面二典型聚集状态标定的Ono-Kondo方程,并用预测精度较高的方程计算了与文献相同条件下的吸附等温线.在比较了计算结果、试验结果和GCMC分子模拟结果后,对Ono-Kondo吸附等温方程的特点、理论基础作了分析,指出了方程的适用范围.     

液晶聚合物/柔性链聚合物共混体系相分离形态

利用元胞动力学方法在二维情况下对浓度、取向序参量的含时Ginzberg-Landau方程进行数值求解,研究了液晶聚合物/柔性链聚合物共混体系的相分离动力学,考察了浓度、取向有序过程的耦合对相分离形态的影响.结果表明,此耦合作用对相分离的时间进程以及相分离图样的空间排布都有影响.液晶聚合物的取向有序相当于增加了两组分间的不相容性而促进两相分离;两个序参量在热力学方面的耦合使液晶聚合物趋向于沿着界面方向取向,而动力学方面的耦合使液晶聚合物分子沿着其取向方向扩散,相分离图样的空间排布由这两种效应共同决定通过极化率张量的定义用数值方法模拟得到了相分离体系的小角光散射图样,结果表明,散射强度分布具有方位角依赖性,它是由浓度、取向序参量的空间变化共同决定的.     

LOW DENSITY POLYETHYLENE/CLAY NANOCOMPOSITES MODIFIED BY ETHYLENE COPOLYMERS： EFFECTS OF FUNCTIONALIZED SEGMENTS ON MORPHOLOGY

Melt extrusion was used to prepare binary nanocomposites of ethylene copolymers and organoclay and trinary nanocomposites of low-density polyethylene （LDPE）, ethylene copolymer and organoclay. X-ray diffraction （XRD） and transmission electron microscopy （TEM） were used to analyze the structure of the clay phase and the morphology of the nanocomposites. Influences of the comonomer in the copolymer and the content of the copolymer on the morphology of the resulting nanocomposites were discussed. The binary and the trinary composites may form intercalated or exfoliated structures depending on the interaction between the copolymer and the clay layers and the content of the copolymer.     

Bimodality of molecular mass distribution of polydienes obtained under the action of dilithium initiators in hydrocarbon media: the reasons,mathematical simulations,and their experimental testing

Bimodal molecular mass distribution (MWD) of polymers, obtained upon polymerization of hydrocarbon monomers in the nonpolar media under the action of dilithium initiators, is the consequence of separation of the reaction mixture into two phases. Bifunctional /living/ oligomers produce the insoluble sediment due to tetrameric association of the lithium active sites (the swollen gel-fraction). Part of the active site remains in the solution (the solfraction). Difference in the concentrations of the active sites into the phases leads to difference between the propagation rates of the /living/ chains and, as a result, to Bimodal MWD. The mathematical model of polymerization in the two-phase system is proposed. Satisfactory agreement between the calculations and the experiments is shown for butadiene polymerization in heptane under the action of 1,4-dilithiumpentane. Regulation of MWD up to the complete elimination of bimodality is possible via the programmed dosage of monomer and solvent into the reactor.     

Investigations of the Mechanism of Alternating Copolymerization with Charge-Transfer Interaction of the Monomers

The applicability of the method of Giese to the measurement of the influence of monomer reactivity is examined. The reaction of alkyl mercuric salts with sodium borohydride permits the production of alkyl (cyclohexyl and butyl) radicals. Since hydrogen radicals are present in high concentration, the addition of alkenes to the reaction mixture leads to radicals from the alkenes. Further addition of alkene (polymerization) can be nearly completely excluded in this way. The composition of the reaction products is determined by gas chromatography. The addition rate of the alkenes relative to styrene allows correlation with the e value of the Q-e scheme of Alfrey and Price. The method answers the question of how far addition of the monomer complex occurs in one step or as separate addition of both monomers during copolymerization in the presence of charge-transfer (CT) complexes of the monomers. The investigations are performed by using the styrene/acrylonitrile/ZnCl₂system, and it is demonstrated that the reactivity of the complexed     

Properties of aqueous solution of sodium glycocholate and a nonionic surfactant,and their mixtures

The micellar properties of aqueous binary mixed solutions of sodium glycocholate, NaGC, and octa-oxyethylene glycol mono-n-decyl ether, C₁₀E₈, have been studied on the basis of surface tensions, the mean aggregation number and the polarity of the interior of the micelles. The mean aggregation number, measured by steady state quenching method, decreased with the increase of the mole fraction of NaGC in the mixed system. The polarity of the interior, estimated by the ratio of first and third vibronic peak in a monomeric pyrene fluorescence emission spectrum, suggested that the hydrophobicity of intramicelles increased with the increase of the mole fraction of NaGC in the mixed system. These are considered to be caused by the differences in the chemical structure and the hydrophobic nature between NaGC and C₁₀E₈. The mean aggregation number and the polarity of the interior for each micelle near the CMC in lower total concentration of surfactants showed the tendency approaching those of pure micelle of the nonionic surfactant. This suggests that the ratio of NaGC in the initial micelles in the range of lower total concentration near the CMC is lower than that of the corresponding prepared mole fraction in the mixed system. This lower value was confirmed also from theoretical calculation of the ratio of NaGC at the CMC in the mixed micelle by regular solution treatment of Rubingh in the solution.     

Reliability and uncertainty in the estimation of p<Emphasis Type="Italic">K</Emphasis><Subscript>a</Subscript> by least squares nonlinear regression analysis of multiwavelength spectrophotometric pH titration data

When drugs are poorly soluble then, instead of the potentiometric determination of dissociation constants, pH-spectrophotometric titration can be used along with nonlinear regression of the absorbance response surface data. Generally, regression models are extremely useful for extracting the essential features from a multiwavelength set of data. Regression diagnostics represent procedures for examining the regression triplet (data, model, method) in order to check (a) the data quality for a proposed model; (b) the model quality for a given set of data; and (c) that all of the assumptions used for least squares hold. In the interactive, PC-assisted diagnosis of data, models and estimation methods, the examination of data quality involves the detection of influential points, outliers and high leverages, that cause many problems when regression fitting the absorbance response hyperplane. All graphically oriented techniques are suitable for the rapid estimation of influential points. The reliability of the dissociation constants for the acid drug silybin may be proven with goodness-of-fit tests of the multiwavelength spectrophotometric pH-titration data. The uncertainty in the measurement of the pK _a of a weak acid obtained by the least squares nonlinear regression analysis of absorption spectra is calculated. The procedure takes into account the drift in pH measurement, the drift in spectral measurement, and all of the drifts in analytical operations, as well as the relative importance of each source of uncertainty. The most important source of uncertainty in the experimental set-up for the example is the uncertainty in the pH measurement. The influences of various sources of uncertainty on the accuracy and precision are discussed using the example of the mixed dissociation constants of silybin, obtained using the SQUAD(84) and SPECFIT/32 regression programs.     

Chain dynamic parameters for some acrylic polymers

The dielectric relaxation data of Ishida et al. on a number of acrylic polymers are represented in terms of the relaxation function proposed by Havriliak and Negami using the multi-response techniques developed by Havriliak and Watts. Two of the parameters of this function are interpreted in terms of a temperature dependent distribution of relaxation times. In this method of interpretation the breadth of the distribution function is temperature-dependent while the skewness is not. The temperature dependence of the breadth of the distribution function is similar for most of these acrylic polymers.The parameters of the relaxation function are also interpreted in terms of Mansfield's model which represents intra- and inter-molecular interactions in terms of springs and dash pots. Briefly, increasing the side chain length for the methacrylate series increases the inter-molecular relaxation time which may be due to an increase in the entropy of activation for the orientation process. The difference between the one acrylate in this study and the four methacrylates of the series is a reduction in the intra-molecular relaxation time, apparently due to the lack of the alpha methyl group.     

PHONONS IN POLYACENIC CHAINS

We have theoretically resolved phonon excitations in quasi-two-dimensional organic crystals of polyacenic semiconductor material which may be obtained by the pyrolytic treatment of phenol-formaldehyde resin. A model for studying the dynamical properties using three polyacene chains is proposed with the aim to present the vibrational properties of this structure. It employs the formalism of solid states in two dimensions which admit phonons. A simulation process of the two-dimensional lattice structure shows that elastic waves may explain the existence of vibrational modes in the frequency range 100-400 cm-1. The presence of acoustic and optical like phonons is discussed in terms of the elastic force constants. A hyperfine resonance structure is obtained. It allows the analysis of the dynamical evolution in thin films of polyacene. It is found that the behavior of the phonon density of states exhibits resonance between modes in the structure.