离子色谱-直接电导检测法分离测定吗啉离子液体阳离子

建立了离子色谱-直接电导检测法分析N-甲基乙基吗啉([MEMo]+)、N-甲基丙基吗啉([MPMo]+)2种吗啉离子液体阳离子的方法。采用磺酸型阳离子交换色谱柱,以乙二胺-乙腈为流动相,研究了色谱柱、流动相、色谱柱温度对吗啉阳离子保留的影响,并讨论了保留规律。结果表明,吗啉阳离子的保留基本属于离子交换模式,是一个放热过程。在柱温30℃,流速1.0 mL/min,以0.1 mmol/L乙二胺-0.5%乙腈(用盐酸调节至pH 5.0)为流动相条件下,[MEMo]+和[MPMo]+阳离子可在4 min内得到基线分离,检出限(S/N=3)分别为0.08、0.13 mg/L,峰面积的相对标准偏差(RSD,n=5)不大于1.5%。将此方法用于测定实验室合成的吗啉离子液体样品,加标回收率为94.0%～106.0%。方法准确、可靠、快速,具有较好的实用性,可满足离子液体样品的检测要求。     

抑制型电导检测法测定饮用水中的碘离子

采用ASRS - ULTRAⅡ4mm阴离子抑制器,将待测水样在IonPac AS 16型阴离子柱上,以55 mmol/LKOH淋洗液等度洗脱,流速为1.0 mL/min,用ICS - 3000型离子色谱仪通过电导检测水样中痕量碘离子含量.碘离子分离效果较好,其浓度在0～40 μg/L范围内与色谱峰面积具有良好的线性,相...     

离子色谱-非抑制电导法同时测定铵盐、四乙基铵、甲基三乙基铵

建立了离子色谱非抑制电导法同时分离测定铵根与两种季铵盐四乙基铵、甲基三乙基铵的方法。分别实验了在亲水性和疏水性阳离子交换色谱柱上三种铵类的分离效果,研究了使用不同淋洗液和流速情况下离子的分离情况,结果表明使用SH-Cation-101型疏水性阳离子色谱柱,淋洗液采用甲烷磺酸(5.0mmol/L),其中加入乙腈(7%),于0.8mL/min的流速条件下,三种铵类物质分离良好,其中结构极为相似的两种季铵盐四乙基铵和甲基三乙基铵分离度达到1.5以上,分离时间短,3种物质在13min内实现完全分离。采用国产离子色谱仪非抑制电导法检测,无需使用抑制器,成本低,操作简便可行。检测结果的灵敏度高,线性范围铵根为0.5～50mg/L,四乙基铵和甲基三乙基铵为5～500mg/L,相关系数均高于0.999,相对标准偏差均在3%以内,平均加标回收率在98.5%～101.2%。     

整体柱和填充柱离子对色谱-间接紫外检测法分析四乙基铵根离子

建立了整体柱离子对色谱-间接紫外检测和填充柱离子对色谱-间接紫外检测分析四乙基铵根离子的两种方法。用反相整体柱和反相填充柱,以咪唑离子液体-离子对试剂-有机溶剂为流动相,研究了背景紫外吸收试剂、检测波长、离子对试剂、有机溶剂、柱温和流速对测定四乙基铵根离子的影响,比较了两种色谱柱的差异,并讨论了保留规律。在优化的实验条件下,两种方法测定四乙基铵根离子的保留时间分别是2.40和3.02 min;检出限分别是0.04和0.07 mg/L;峰面积的相对标准偏差分别是0.16%和0.11%;保留时间的相对标准偏差分别是0.02%和0.01%。将这两种方法用于分析实验室合成的溴化四乙基铵离子液体,加标回收率分别为98.2%和99.1%。两种方法均能满足四乙基铵根离子测定的需要。     

瓶装饮用水中高氯酸盐含量的离子色谱-电导检测法和离子色谱-串联质谱法测定研究

建立了离子色谱-电导检测法(IC-CD)和离子色谱-串联质谱法(IC-MS/MS)测定瓶装饮用水中高氯酸盐浓度的方法,并对两种方法进行F检验(精密度)和t检验(系统误差).结果 表明,IC-CD的检出限为0.35 μg·L-1,定量限为1.17 μg·L-1,在0.5～8.0 μg·L-1范围内呈线性关系(R2 =0....     

离子色谱-电导检测法测定不同乳制品中硫氰酸盐

建立了离子色谱-电导检测分析不同类型乳制品中硫氰酸盐(SCN-)污染物的方法,重点研究了不同形态样品如固态类(奶粉)、液态类(牛奶)、凝固态类(凝固型酸奶)和半流质态类(炼乳)等乳制品中的硫氰酸盐前处理方法,采用丙酮作为蛋白沉淀剂,有效实现了对各类样品中蛋白质的沉淀和对硫氰酸盐的提取,避免了以往采用乙腈处理样品时容易分层的弊端,方法在0～5.0mg/L浓度范围内具有良好的线性关系,相关系数r为0.9997(n=6),方法检出限(LOD)为0.15～0.5μg/g,方法回收率为95.0%～105.0%,相对标准偏差(RSD)为1.4%～5.6%(n=3)。     

离子液体中卤素离子杂质的离子色谱-直接电导检测法分析

研究了离子色谱-直接电导检测法分离测定离子液体中的卤素离子(F~-、Cl~-、Br~-)杂质.采用Shim-pack IC-A3阴离子交换色谱柱,考察了淋洗液种类及浓度、流速和色谱柱温度对分离测定的影响.最佳色谱条件为:以1.25 mmol/L邻苯二甲酸氢钾为淋洗液,流速1.5 mL/min,色谱柱温45 ℃.在此条件下可以基线分离卤素离子,且NO~-_3、BF~-_4、SO~(2-)_4不干扰测定.该法测定卤素离子的检出限(S/N=3)为0.02 ～0.11 mg/L,峰面积的相对标准偏差(n=5)不大于0.7%,F~-、Cl~- 和Br~- 的标准曲线的线性范围分别为0.1 ～50、0.1 ～50、0.5 ～100 mg/L.将方法用于烷基咪唑四氟硼酸盐离子液体中卤素离子杂质的测定,加标回收率为98% ～102%.     

离子色谱-直接电导检测法分析哌啶离子液体阳离子

建立了离子色谱-直接电导检测法分析N-甲基,乙基哌啶(［MEPi］+)、N-甲基,丙基哌啶(［MPPi］+)和N-甲基,丁基哌啶(［MBPi］+) 3种哌啶离子液体阳离子的方法。采用磺酸型阳离子交换色谱柱,以乙二胺-柠檬酸-乙腈为流动相。考察了流动相组成及色谱柱温度对哌啶阳离子保留的影响,并讨论了保留规律。结果表明,哌啶阳离子的保留是一个放热过程,即哌啶阳离子的保留时间随着色谱柱温度的升高而缩短,且哌啶阳离子同系物的保留符合碳数规律。在以0.2 mmol/L乙二胺-0.3 mmol/L柠檬酸-3%(v/v)乙腈(pH 4.4)为流动相、流速1.0 mL/min、柱温30 ℃条件下,［MEPi］+、［MPPi］+和［MBPi］+3种哌啶阳离子可以在7 min内分离,检出限(信噪比为3)分别为0.14、0.20和0.56 mg/L,峰面积的相对标准偏差(n=5)在1.2%以下。将此方法应用于分析实验室合成的哌啶离子液体样品,加标回收率在97.6%与105.1%之间。本方法准确、可靠、快速,具有较好的实用性。     

离子色谱-抑制电导检测法同时测定草甘膦母液中的含磷副产物及无机阴离子

建立了一种抑制电导检测-离子色谱(IC)同时测定草甘膦生产工艺中母液里的草甘膦及其副产物、无机阴离子的方法。样品经过滤后直接进样,色谱条件: IonPac AS11-HC分离柱(250 mm×4 mm)和IonPac AG11-HC保护柱(50 mm×4 mm),在线淋洗液发生器KOH梯度淋洗,流速1.0 mL/min,采用抑制电导检测。草甘膦、甲基草甘膦、六甲基磷酰三胺(HMPA)、增甘膦、亚磷酸、磷酸、Cl~和SO2~4的线性范围分别为0.1～20 mg/L、0.1～20 mg/L、0.1～50 mg/L、0.25～50 mg/L、0.05～20 mg/L、0.2～50 mg/L、0.02～20 mg/L和0.05～50 mg/L,相关系数分别为0.9995、0.9993、0.9999、0.9998、0.9999、0.9985、0.9999和0.9980,加标回收率为93.7%～104.0%,相对标准偏差均小于2.5% (n=7),检出限(以信噪比(S/N)=3计)为0.002～0.025 mg/L。该方法用于草甘膦生产工艺中母液里草甘膦及其含磷副产物和无机阴离子的测定,结果令人满意。     

离子色谱-电导检测法测定左乙拉西坦中四丁基溴化铵残留

建立了左乙拉西坦原料药中痕量四丁基溴化铵测定的离子色谱方法.以Dionex IonPac CS17阳离子交换色谱柱为分析柱,15mmol/L甲磺酸溶液-乙腈淋洗液,流速为1.0mL/min,抑制型电导检测器.样品基质及常见阳离子对测定无干扰,四丁基溴化铵质量浓度在0.5～20mg/L范围内与峰面积线性关系良好,相关系数...     

Effects of ion association of lipophilic quaternary ammonium salts in ion-exchange and potentiometric selectivity

It has been found experimentally and substantiated theoretically that the anion-exchange selectivity in water—lipophilic quaternary ammonium salts (QAS) toluene solutions systems as well as the potentiometric selectivity of plasticized PVC membranes containing QAS, are strongly influenced by ion association. In particular, it has been demonstrated that varying the steric accessibility of QAS exchange center is a powerful tool for the selectivity control. The experimental values of the selectivity change caused by variations in the QAS exchange center steric accessibility were about 3 orders of magnitude when the single-charged ions were exchanged for the single-charged ones and more than seven orders when double-charged ions were exchanged for the single-charged. The above effects have also been observed for the potentiometric selectivity of QAS-based PVC membranes and, to some extent, for the potentiometric selectivity of the neutral anion carrier-based membranes doped by QAS to provide anion permselectivity. This fact is of immediate practical interest for the development of ISE with improved selectivity. The obtained results allow to revise the generally accepted idea of QAS as “nonselective” ion-exchangers and to suggest specific ways for controlling the ion-exchange and potentiometric selectivity using the ion association as a tool.     

Measuring quaternary ammonium cleaning agents with ion selective electrodes

Data for coated-wire, ion selective electrodes (ISEs) are presented for cationic surfactant ions found in common cleaners including benzyldimethyltetradecylammonium, benzyldimethyldodecylammonium, and benzyldimethylhexadecylammonium. The ion exchangers dinonylnaphthalene sulfonic acid, tetraphenyborate, and tetrakis(4-chlorophenyl)borate are examined, showing dinonylnaphthalene sulfonic acid to be the favored species. The ISEs exhibit approximately Nernstian behavior down to the 10⁻⁶ M limit of detection with lifetimes in excess of 50 days when used continuously, and a shelf life of over 100 days. Reaching the upper detection limit at the critical micelle concentration requires use of polymeric-membrane reference electrodes including a new membrane cocktail, which allow response measurements of an order of magnitude higher than the traditional fritted-glass reference electrode. The surfactant ISEs show excellent selectivity over the common metal ions Na⁺, K⁺, Mg²⁺, Ca²⁺, and Cu²⁺ with selectivity coefficients less than 10^−5.3. The ISEs are also selective over the lower molecular weight quaternary ammonium ions tetradecyltrimethylammonium, dodecyltrimethylammonium, benzyldimethyl(2-hydroxyethyl)ammonium, and tetrabutylammonium with selectivity coefficients ranging from 10^−1.7 to 10^−5.5. Use of a single electrode to determine accurately the total cationic surfactant concentration in common cleaning solutions is accomplished with information about concentration dependent interferences and a modified Nikolsky–Eisenman model. Finally, quaternary ammonium surfactants have a deleterious effect on the measurements of pH and common ions like K⁺, Mg²⁺ and Ca²⁺ with polymeric ISEs. This makes it critical to include surfactant electrodes in a detector array when cleaning agents are present.     

Determination of the quaternary ammonium ion components of Aliquat 336 by electrospray mass spectrometry

A procedure is described for the identification and determination of the quaternary ammonium ion components of the commercial solvent extraction reagent Aliquat 336 using Electro Spray Mass Spectrometry (ESMS). The procedure is extremely rapid when compared with an existing procedure based on gas chromatography and produces comparable results in terms of accuracy and precision.     

Modified gelatin with quaternary ammonium salts containing epoxide groups

An EPDDMAC-GE polymer （hydrophilic molecule） has been synthesized based on epoxypropyl dodecyl dimethyl ammonium chloride （EPDDMAC） and gelatin. A DEEPSAC-GE polymer （hydrophobic molecule） has been synthesized based on diethyl-2,3-epoxypropyl-[3-methyldimethoxyl] silpropyl ammonium chloride （DEEPSAC） and gelatin. Compared with initial gelatin, the gelatin modified with quaternary ammonium salts containing epoxide groups exhibits stronger antibacterial activity.     

Preparation and antibacterial activity of hybrid materials containing quaternary ammonium salts via sol-gel process

Organic-inorganic hybrid coatings containing quaternary ammonium salts (QAS) bonded to the organic-inorganic network were prepared from tetraethoxysilane and triethoxysilane terminated poly(ethylene glycol)-block-poly(ethylene) using a sol-gel process. They were applied as a thin layer (0.6-1 μm) to PE films and the antibacterial activity of the coated films was tested against both Gram-negative (Escherichia coli ATCC 25922) and Gram-positive (Staphylococcus aureus ATCC 6538) bacteria. Measurements at different contact times showed a rapid decrease of the viable count for both the tested strains. In particular, after 48 h of contact, a decrease of 96.4% and 99.1% of E. coli and S. aureus, respectively, was observed. The permanence of the antibacterial activity of the coated films was demonstrated through repeated washings and prolonged immersion in physiological saline solutions at 37 °C. Indeed, due to the removal of QAS moieties by the nucleophilic attack of water, the antibacterial activity after 24 h was strongly reduced when measured on samples submitted to several washings. However, a quite good antibacterial activity was observed even on the same samples after 96 h, probably due to a spontaneous partial restoring of the QAS on the surface. Very good transparency, quite good adhesion and high wettability are further features of these hybrid coatings.     

Determination of homologues of quaternary ammonium surfactants by capillary electrophoresis using indirect UV detection

This investigation describes the simultaneous separation of two major non-chromophoric quaternary ammonium surfactants, alkyltrimethyl- and dialkyldimethylammonium compounds (ATMACs and DADMACs, respectively), by capillary electrophoresis (CE) using indirect UV detection. The most effective separation conditions was 10 mM phosphate buffer with 57.5% tetrahydrofuran and 3 mM sodium dodecyl sulfate (SDS) at pH 4.3, and the sample hydrodynamic injection of up to 20 s at 1 psi (approximately 60 nl), and an applied voltage of 25 kV (1 psi = 6.9 kPa). Specially, the selection of an appropriate chromophore and an internal standard (I.S.) to improve the peak identification and quantitation was systematically investigated. Decylbenzyldimethyl ammonium chloride (C10-BDMA+C-) as a chromophore with 3 mM sodium dodecyl sulfate provided the best detectability for all homologues. The reproducibility of the migration time and quantitative analysis can be improved by using tetraoctyl ammonium ion as an internal standard, giving the relative standard deviation (R.S.D.) less than 0.8% for the relative migration times, and 2.5-5.5% for the relative peak areas. A good linearity of CE analysis was obtained in the range of 1.0-20 microg/ml with r2 values of above 0.999. The analysis of cationic surfactants in commercial products of hair conditioners and fabric softeners was also performed. Electrospray mass spectrometric method was applied to evaluate the CE method, and the compatible results were obtained.     

Dimethyl carbonate synthesis via transesterification catalyzed by quaternary ammonium salt functionalized chitosan

A quaternary ammonium salt covalently linked to chitosan was first used as a catalyst for dimethyl carbonate （DMC） synthesis by the transesterification of propylene carbonate （PC） with methanol. The effects of various reaction variables like reaction time, temperature and pressure on the catalytic performance were also investigated. 54% DMC yield and 71% PC conversion were obtained under the optimal reaction conditions. Notably, the catalyst was able to be reused with retention of high catalytic activity and selectivity. Consequently, the process presented here has great potential for industrial application due to its advantages such as stability, easy preparation from renewable biopolymer, and simple separation from products.     

Separation and determination of quaternary ammonium compounds by high-performance liquid chromatography with a hydrophilic polymer column and conductometric detection

An HPLC method has been developed for separation and determination of long alkyl chain quaternary ammonium compounds. A column packed with a hydrophilic polymer packing, Shodex Asahipak GF-310 HQ, and a water–acetonitrile mixture containing 4,4′-bipyridyl and hydrochloric acid were used to depress hydrophobic adsorption of the quaternary ammonium compounds and increase the sensitivity of the conductometric detection with a micromembrane suppressor. Dodecyltrimethylammonium, cetyltrimethylammonium, tetradecyldimethylbenzylammonium and stearyltrimethylammonium ions can be completely separated from one another and quantified at 0.1 nmol level.     

Determination of quaternary alkylammonium compounds by capillary zone electrophoresis and indirect UV detection as a real alternative to ion chromatography with suppressed conductivity detection

A capillary electrophoretic (CE) method for the determination of residual mid-chain alkyltrimethylammonium compounds in the pharmaceutical product Welchol™ (an alkylated, crosslinked polyallylamine) was developed, validated and compared with the existing ion chromatographic (IC) method with suppressed conductivity detection. Excellent reproducibilities of migration times (RSD<0.5% within a series of 55 sample injections) and relative peak areas (RSD<2%) make the method suitable for quality control as a real alternative to IC. Limits of quantification of 0.01% w/w of each impurity in the active substance were achieved. Buffer systems for indirect UV detection based on creatinine as visualization reagent with different inorganic and organic acids (phosphoric, sulfuric, formic, acetic, oxalic and citric acid) and their effect on selectivity to ten quaternary ammonium compounds were studied. Selectivity changes were observed for the di- and trivalent analytes depending on the buffer applied. Also, the influence of acetonitrile, methanol, 1,4-dioxane and tetrahydrofuran on selectivity was investigated. In addition, CE–MS experiments were carried out in order to identify several impurities in the product.