Simultaneous determination of lead(II) and cadmium(II) at a diacetyldioxime modified carbon paste electrode by differential pulse stripping voltammetry

A simple and effective chemically modified carbon paste electrode (CMCPE) for the simultaneous determination of lead(II) and cadmium(II) was developed in this work. The electrode was prepared by the addition of diacetyldioxime into a carbon paste mixture. Pb²⁺ and Cd²⁺ were preconcentrated on the surface of the modified electrode by complexing with diacetyldioxime and reduced at a negative potential (−1.10 V). Then the reduced products were oxidized by differential pulse stripping. The fact that two stripping peaks appeared on the voltammograms at the potentials of −0.65 V (Cd²⁺) and −0.91 V (Pb²⁺) demonstrates the possibility of simultaneous determination of Pb²⁺ and Cd²⁺. Under the optimized working conditions, calibration graphs were linear in the concentration ranges of 1.0×10⁻⁷-1.5×10⁻⁵ mol l⁻¹ (Pb²⁺) and 2.5×10⁻⁷-2.5×10⁻⁵ mol l⁻¹ (Cd²⁺), respectively. For 5 min preconcentration, detection limits of 1×10⁻⁸ mol l⁻¹ (Pb²⁺) and 4×10⁻⁸ mol l⁻¹ (Cd²⁺) were obtained at the signal noise ratio (SNR) of 3. To evaluate the reproducibility of the newly developed electrode, the measurements of 5×10⁻⁷ mol l⁻¹ Pb²⁺ and Cd²⁺ were parallel carried out for six times at different electrodes and the relative standard deviations were 2.9% (Pb²⁺) and 3.2% (Cd²⁺), respectively. Interferences by some metals were investigated. Only Ni²⁺ and Hg²⁺ apparently affected the peak currents of Pb²⁺ and Cd²⁺. The diacetyldioxime modified carbon paste electrode was applied to the determination of Pb²⁺ and Cd²⁺ in water samples. The results indicate that this electrode is sensitive and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Electrochemical sensor for Cd2+ and Pb2+ detection based on nano-porous pseudo carbon paste electrode

An electrochemical sensor based on self-made nano-porous pseudo carbon paste electrode (nano-PPCPE) has been successfully developed, and used to detect Cd²⁺ and Pb²⁺. The experimental results showed that the electrochemical performance of nanoPPCPE is evidently better than both glassy carbon electrode (GCE) and pure carbon paste electrode (CPE). Then the prepared nano-PPCPE was applied to detect Cd²⁺ and Pb²⁺ in standard solution, the results showed that the electrodes can quantitatively detect trace Cd²⁺ and Pb²⁺, which has great significance in electrochemical analysis and detection. The linear ranges between the target ions concentration and the DPASV current were from 0.1–3.0 μmol/L, 0.05–4.0 μmol/L for Cd²⁺ and Pb²⁺, respectively. And the detection limits were 0.0780 μmol/L and 0.0292 μmol/L, respectively. Moreover, the preparation of the nano-PPCPE is cheap, simple and has important practical value.     

Bifunctional polydopamine@Fe3O4 core–shell nanoparticles for electrochemical determination of lead(II) and cadmium(II)

The present paper has focused on the potential application of the bifunctional polydopamine@Fe₃O₄ core–shell nanoparticles for development of a simple, stable and highly selective electrochemical method for metal ions monitoring in real samples. The electrochemical method is based on electrochemical preconcentration/reduction of metal ions onto a polydopamine@Fe₃O₄ modified magnetic glassy carbon electrode at −1.1 V (versus SCE) in 0.1 M pH 5.0 acetate solution containing Pb²⁺ and Cd²⁺ during 160 s, followed by subsequent anodic stripping. The proposed method has been demonstrated highly selective and sensitive detection of Pb²⁺ and Cd²⁺, with the calculated detection limits of 1.4 × 10⁻¹¹ M and 9.2 × 10⁻¹¹ M. Under the optimized conditions, the square wave anodic stripping voltammetry response of the modified electrode to Pb²⁺ (or Cd²⁺) shows a linear concentration range of 5.0–600 nM (or 20–590 nM) with a correlation coefficient of 0.997 (or 0.994). Further, the proposed method has been performed to successfully detect Pb²⁺ and Cd²⁺ in aqueous effluent.     

Electrochemical Determination of Cd2+ and Pb2+ Using NSAID‐mefenamic Acid Functionalized Mesoporous Carbon Microspheres Modified Glassy Carbon Electrode

This paper describes the electrochemical behaviors of Cd²⁺ and Pb²⁺ on the proposed mesoporous carbon microspheres/mefenamic acid/nafion modified glassy carbon electrode (MC/MA/Nafion/GC) studied by square wave anodic stripping voltammetry (SWASV). The prepared material is characterized by XRD, SEM, FTIR, RAMAN and BET analysis. Experimental parameters, such as the deposition potential and time, the pH value of buffer solution were optimized. Under the optimized conditions, the electrode responded linearly to Cd²⁺ and Pb²⁺ in the concentration range from 50 to 300 nM, and the detection limits were 24.2 and 11.26 nM respectively. The sensitivity determined was 0.0623 μA/nM (Cd²⁺) and 0.192 μA/nM (Pb²⁺). Multiple metal ion detection with clear demarcation of peaks was produced by the electrode. Moreover, the modified electrode has possessed good selectivity and reproducibility of Cd²⁺ and Pb²⁺ detection. We also investigated the interference of various anions and surfactants for the detection of Cd²⁺ and Pb²⁺ ions. Finally the modified electrode was used to detect the presence of metal ions in practical samples and the results obtained are comparatively good with respect to AAS.     

Synthesis of a novel electrode material containing phytic acid-polyaniline nanofibers for simultaneous determination of cadmium and lead ions

The development of nanostructured conducting polymers based materials for electrochemical applications has attracted intense attention due to their environmental stability, unique reversible redox properties, abundant electron active sites, rapid electron transfer and tunable conductivity. Here, a phytic acid doped polyaniline nanofibers based nanocomposite was synthesized using a simple and green method, the properties of the resulting nanomaterial was characterized by electrochemical impedance spectroscopy (EIS), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS). A glassy carbon electrode modified by the nanocomposite was evaluated as a new platform for the simultaneous detection of trace amounts of Cd²⁺ and Pb²⁺ using differential pulse anodic stripping voltammetry (DPASV). The synergistic contribution from PANI nanofibers and phytic acid enhances the accumulation efficiency and the charge transfer rate of metal ions during the DPASV analysis. Under the optimal conditions, good linear relationships were obtained for Cd²⁺ in a range of 0.05–60 μg L⁻¹, with the detection limit (S/N = 3) of 0.02 μg L⁻¹, and for Pb²⁺ in a range of 0.1–60 μg L⁻¹, with the detection limit (S/N = 3) of 0.05 μg L⁻¹. The new electrode was successfully applied to real water samples for simultaneous detection of Cd²⁺ and Pb²⁺ with good recovery rates. Therefore, the new electrode material may be a capable candidate for the detection of trace levels of heavy metal ions.     

Development of carbon paste electrode modified with cadmium ion-imprinted polymer for selective voltammetric determination of Cd2+

A simple and fast voltammetric method based on a new electrode composed of carbon paste electrode/bifunctional hybrid ion imprinted polymer (CPE/IIP) was developed for the quantification of Cd²⁺ in water samples. The voltammetric measurements by Differential Pulse Voltammetry were performed by using CPE containing 11.0 mg of IIP under phosphate buffer solution at concentration 0.1 mol L^?1 and pH 6.5. The electrochemical method was carried out by Cd²⁺ preconcentration at ?1.2 V during 210 s, followed by anodic stripping. The performance of IIP towards Cd²⁺ determination was evaluated by comparison to non-imprinted polymer, whose detectability of IIP was much higher (45%). The sensitivity of the sensor was found to be 0.0105 µA/µg L^?1. The limits of detection and limits of quantification were found to be 4.95 μg L^?1 and 16.4 μg L^?1, respectively. The developed method was successfully applied to Cd²⁺ determination in mineral, tap and lake water samples, whose results are in agreement with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) used as reference analytical technique. According to achieved results, the developed method can be used for routine analysis of quality control of water samples from different sources.     

Determination of Cd and Pb on glassy carbon electrode modified by electrochemical reduction of aromatic diazonium salts

Carbon modified by the reduction of aromatic diazonium derivatives was first used as electrode for the electrochemical stripping analysis of heavy metals. As a model, the glassy carbon electrode was modified with benzoic acid by electrochemical reduction of diazobenzoic acid, and the resulting modified electrodes were used for determination of Cd²⁺ and Pb²⁺. The anodic peak currents of cadmium and lead at the benzoic acid-modified glassy carbon electrode are 7.2 and 6 times of that at the bare glassy carbon electrode. A linear response was observed for Pb²⁺ and Cd²⁺ in the range of 0.5–50 μg/l. The detection limits are 0.20 μg/l for Pb²⁺ and 0.13 μg/l for Cd²⁺. The relative standard deviations for six consecutive measurements of 50 μg/l Cd²⁺ and 50 μg/l Pb²⁺ are 0.82% and 3.02%, respectively. Applicability of the sensor to the determination of Cd²⁺ and Pb²⁺ in sewerage samples was demonstrated.     

The Fabrication and Characterization of a Bismuth Nanoparticle Modified Boron Doped Diamond Electrode and Its Application to the Simultaneous Determination of Cadmium(II) And Lead(II)

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by square‐wave anodic stripping voltammetry (SWASV) using a bismuth nanoparticle modified boron doped diamond (Bi‐BDD) electrode. Bi deposition was performed in situ with the analytes, from a solution of 0.1 mM Bi(NO₃)₃ in 0.1 M HClO₄ (pH 1.2), and gave detection limits of 1.9 μg L^?1 and 2.3 μg L^?1 for Pb(II) and Cd(II) respectively. Pb²⁺ and Cd²⁺ could not be detected simultaneously at a bare BDD electrode, whilst on a bulk Bi macro electrode (BiBE) the limits of detection for the simultaneous determination of Pb²⁺ and Cd²⁺ were ca. ten times higher.     

In-channel indirect amperometric detection of heavy metal ions for electrophoresis on a poly(dimethylsiloxane) microchip

In-channel indirect amperometric detection mode for microchip capillary electrophoresis with positive separation electric field is successfully applied to some heavy metal ions. The influences of separation voltage, detection potential, the concentration and pH value of running buffer on the response of the detector have been investigated. An optimized condition of 1200 V separation voltage, −0.1 V detection potential, 20 mM (pH 4.46) running buffer of 2-(N-morpholino)ethanesulfonic acid (MES) + l-histidine (l-His) was selected. The results clearly showed that Pb²⁺, Cd²⁺, and Cu²⁺ were efficiently separated within 80 s in a 3.7 cm long native separation PDMS/PDMS channel and successfully detected at a single carbon fibre electrode. The theoretical plate numbers of Pb²⁺, Cd²⁺, and Cu²⁺ were 1.2 × 10⁵, 2.5 × 10⁵, and 1.9 × 10⁵ m⁻¹, respectively. The detection limits for Pb²⁺, Cd²⁺, and Cu²⁺ were 1.3, 3.3 and 7.4 μM (S/N = 3).     

Copper (II) Sensor Based on a Cephaloridine Antibiotic PVC Matrix

ABSTRACT

A poly (vinyl chloride) (PVC) based membrane of cephaloridine as a novel ionophore exhibits good potentiometric response for Cu²⁺ over a wide concentration range (10^?5-10^? M) with a slope of 28.5 mV per decade. The detection limit is 3.5 × 10^?6 M. The response time of the sensor is < 60 s. The electrode has been used for a period of one month and exhibits good selectivity towards Cu²⁺ in comparison to alkali, alkaline earth, transition and heavy metal ions, with no interference caused by Pb²⁺ Cd²⁺ and Fe²⁺ which are known to interfere with many other copper electrodes. The electrode can be used in the pH range from 4.0 to 6.5 and it can also be used in partially non-aqueous medium having up to 10 (v/v) non aqueous content and in the presence of cationic surfactants at concentrations less than 10^?3 M.     

High-sensitivity determination of lead and cadmium based on the Nafion-graphene composite film

Graphene nanosheets, dispersed in Nafion (Nafion-G) solution, were used in combination with in situ plated bismuth film electrode for fabricating the enhanced electrochemical sensing platform to determine the lead (Pb²⁺) and cadmium (Cd²⁺) by differential pulse anodic stripping voltammetry (DPASV). The electrochemical properties of the composite film modified glassy carbon electrode were investigated. It is found that the prepared Nafion-G composite film not only exhibited improved sensitivity for the metal ion detections, but also alleviated the interferences due to the synergistic effect of graphene nanosheets and Nafion. The linear calibration curves ranged from 0.5 μg L⁻¹ to 50 μg L⁻¹ for Pb²⁺ and 1.5 μg L⁻¹ to 30 μg L⁻¹ for Cd²⁺, respectively. The detection limits (S/N = 3) were estimated to be around 0.02 μg L⁻¹ for Pb²⁺ and Cd²⁺. The practical application of the proposed method was verified in the water sample determination.     

Studies on Synthetic Inorganic Ion Exchangers-III Quantitative Separations of Mg2+ -Pb2+, Zn2+ - Pb2+ Cu2+ - Pb2+, Al3+ - Pb2+, Zn2+ - Cd2+, and Mg2+ - Cd2+ on Lead Antimonate Columns

Abstract

A new inorganic ion exchanger, lead antimonate has been synthesized having an Pb:Sb ratio of 1:5 and cation exchange capacity of 1.46 mequiv./g. It is fairly stable in water and dilute solutions of acids, bases and salts. Ion distribution studies on twenty metal ions have been determined on this gel at pH 1,2,3 and 5. The following mixtures have been separated: Mg²⁺ - Pb²⁺, Zn²⁺ - Pb²⁺, Zn²⁺ - Pb²⁺, Cu²⁺ - Pb²⁺, Al³⁺ - Pb²⁺, Zn²⁺ - Cd²⁺ and Mg²⁺ - Cd²⁺. Mg²⁺ and Al³⁺ were removed with 0.4 M ammonium nitrate, Cu²⁺ and Zn²⁺ with 0.4 M ammonium nitrate + 0.1M nitric acid (1:1), Pb²⁺ with 0.5M nitric acid and Cd²⁺ with 0.25M nitric acid. A tentative structure of this material is proposed on the basis of chemical analysis, pH titrations, thermogravimetry and IR spectrophotometry.     

Evaluation of PANI-Averraoha bilimbi leaves activated carbon nanocomposite for Cd2+ and Pb2+ removal from wastewater

In current investigation, we synthesized new Polyaniline-Averraoha Bilimbi Leaves Activated Carbon (PANI-ABLC) nanocomposites and utilized as cost effectual for the elimination of Cd²⁺ and Pb²⁺ ions from the wastewater. The synthesized nanocomposite was confirmed by Scanning Electron Microscopy (SEM) with Energy Dispersive X-Ray (EDX), Fourier Transform-Infrared (FT-IR) spectroscopy and X-Ray Diffraction (X-RD) techniques. A batch adsorption study carried in wastewater containing different concentrations of Cd²⁺ and Pb²⁺ ions in the temperature range of 303–343 K. The results show that, around 80% of Cd²⁺ and Pb²⁺ ions from the wastewater was successfully isolated by using PANI-ABLC nanocomposite. Attempts were made to fit adsorption to different isotherm models. The PANI-ABLC nanocomposite complied Langmuir adsorption model (R² = 0.999) and pseudo-second order kinetics. Further, maximum adsorption efficiency observed at 0.5 g of Polyaniline-Averraoha bilimbi leaves activated carbon nanocomposites. AC- Impedance Spectroscopy (IS) technique shows that, Polyaniline-Averraoha Bilimbi Leaves Activated Carbon (PANI-ABLC) nanocomposite is suitable for removal of Cd²⁺ and Pb²⁺ ions from the wastewater. AC impedance spectroscopy technique study shows that, the process of adsorption was controlled by charge transfer process.     

Synthesis and characterisation of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) Zr(IV) monothiophosphate composite cation exchanger: analytical application as lead ion selective membrane electrode

A Pb²⁺ ion selective membrane electrode based on poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) Zr(IV) monothiophosphate composite cation exchange material was fabricated using solution casting method. The effect of membrane composition on the proton exchange capacity was investigated by using varying amounts of electroactive material. The membrane with 250 mg of electroactive material and 10 µL of plasticiser exhibited higher proton conductivity. The optimised membrane composition was used for the fabrication of ion selective membrane electrode which exhibited typical Nernstian response towards Pb²⁺ ions in the concentration range 20.70 gL^?1–20.7 µgL^?1 (1 × 10^–1–1 × 10^–7 mol L^?1) with a sub-Nernstian slope of 27.429 mV per decade change in Pb²⁺ ion concentration. The response time of the electrode under study for Pb²⁺ ions was found to be 11 s and the electrode can be used for 120 days without any considerable divergence in response potential. It can also be successfully used in the pH range from 3.0 to 6.5. It was found selective for Pb²⁺ ions in the presence of various monovalent, divalent and trivalent interfering metal ions. It was also employed as an indicator electrode in the potentiometric titration of Pb²⁺ ions using ethylenediaminetetraacetic acid, disodium salt, as a titrant.     

Quinoline-based highly selective and sensitive fluorescent probe specific for Cd2+ detection in mixed aqueous media

Quinoline-based fluorescent probe as a recognition unit was designed and synthesized in this study. The probe R1 displayed excellent selectivity and sensitivity for cadmium ions (Cd²⁺) over a wide range of metal ions in acetonitrile-water (MeCN-H₂O) mixed solution. In order to better understand the recognition mechanism between probe and Cd²⁺, the density functional theory calculations were performed. Finally, the colorimetric experiment result was observed and conveniently monitored by the naked eye, and a visual detection limit of 4 × 10^?6 mol L^?1 was achieved. These experimental results indicated the promising potential of the probe to detect Cd²⁺ in biological system. Furthermore, the probe R1 was successfully used for the highly sensitive detection of Cd²⁺ in living cells.     

Electroanalytical Determination of Cadmium(II) and Lead(II) Using an Antimony Nanoparticle Modified Boron‐Doped Diamond Electrode

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by linear sweep anodic stripping voltammetry (LSASV) using an antimony nanoparticle modified boron doped diamond (Sb‐BDD) electrode. Sb deposition was performed in situ with the analytes, from a solution of 1 mg L^?1 SbCl₃ in 0.1 M HCl (pH 1). Pb²⁺ inhibited the detection of Cd²⁺ during simultaneous additions at the bare BDD electrode, whereas in the presence of antimony, both peaks were readily discernable and quantifiable over the linear range 50–500 μg L^?1.     

Study on Cd2+ Determination Using Bud-like Poly-L-Tyrosine/Bi Composite Film Modified Glassy Carbon Electrode Combined with Eliminating of Cu2+ Interference by Electrodeposition

A bud-like poly-L-tyrosine/Bi modified glassy carbon electrode (p-Tyr/Bi/GC) was prepared by CV and in situ Bi plating, whose conductivity and membrane morphology were characterized by CV, EIS and SEM, respectively. The p-Tyr membrane can effectively promote the enrichment of Cd²⁺. The optimal Tyr concentration and scanning number for p-Tyr/GC preparation were 2.0 mmol ⋅ L⁻¹ and 35, while the optimal Bi³⁺ concentration, pH and Cd²⁺ accumulation potential in test medium were 3.0 μmol ⋅ L⁻¹, 6.5 and −1.3 V, respectively. The linear equation of p-Tyr/Bi/GC's response to Cd²⁺ (1.0 nmol ⋅ L⁻¹ to 2.0 μmol ⋅ L⁻¹) was i_p (μA) = −0.6809 + 100.2c (μmol ⋅ L⁻¹) (R² = 0.9985) with a detection limit of 0.11 nmol ⋅ L⁻¹ (3S/N). The elimination of interference caused by Cu²⁺ in sample was studied by electrodeposition. The p-Tyr/Bi/GC electrode was successfully used for detecting Cd in rice samples with good reliability and accuracy. The developed Cd²⁺ sensor exhibits high sensitivity, wide linear range and low detection limit, especially the designed method of eliminating Cu²⁺ interference has the characteristics of high selectivity, simple operation and wide application range.     

Novel Designing of Chemically Modified Electrode (CME) of the Bio-MOF-1 for the Detection of Dopamine Based on Inhibition of [Ru(bpy)3]2+/DBAE System

Metal organic frameworks (MOFs) have attracted extensive attention in electrochemical research fields due to their high surface area and controlled porosity. Current study is design to investigate the ECL performance of the chemically modified electrode (CME) based on the bio-MOF-1, a porous zinc-adenine framework, which loaded ruthenium complex and employed for the detection of dopamine (DA). The composite material [Ru(bpy)₃]²⁺@bio-MOF-1 (Ru-bMOF) modified carbon glassy electrode (Ru-bMOF/GCE) exhibited an excellent ECL performance having a linear co-efficient response (R²=0.9968) for 2-(dibutyl amino) ethanol (DBAE), a classical ECL co-reactant was obtained over a concentration range of 1.0×10⁻⁹ M to 1.0×10⁻⁴ M in 0.10 M pH=6.0 phosphate buffer solution (PBS). Furthermore, DA was detected based on its inhibition effect on [Ru(bpy)₃]²⁺/DBAE system. Compared to traditional analytical methods, this method has various advantages such as simple electrode preparation, quick response, high reproducibility (RSD<2.0 %), low limit of detection (LOD=1.0×10⁻¹⁰ mol/L). This chemical investigated modified electrode had exploited potential for detection of DA.     

Zirconium(IV) phosphosulphosalicylate-based ion selective membrane electrode for potentiometric determination of Pb(II) ions

Zirconium(IV) phosphosulphosalicylate, a cation exchanger was synthesized by mixing zirconium oxychloride to a mixture of 5-sulphosalicylic acid and phosphoric acid. The material showed good efficiency for the preparation of an ion-selective membrane electrode. The membrane was characterized affinity for Pb(II) ions. Due to its Pb(II) selective nature, the ion-exchanger was used as an electroactive by XRD and SEM analysis. The electrode responds to Pb(II) ions in a linear range from 1 × 10⁻⁵ to 1 × 10⁻¹ M with a slope of 43.8 mV per decade change in concentration with detection limit of 4.78 × 10⁻⁶ M. The life span of electrode was found to be 90 days. The proposed electrode showed satisfactory performance over a pH range of 4.0–6.5, with a fast response time of 15 s. The sensor has been applied to the determination of Pb(II) ions in water samples of different origins. It has also been used as indicator electrode in potentiometric titration of Pb(II) ion with EDTA.     

A Potentiometric Sensor for Cd2+ Based on Carbon Nanotube Paste Electrode Constructed from Room Temperature Ionic Liquid,Ionophore and Silica Nanoparticles

A novel and effective potentiometric sensor for the rapid determination of Cd²⁺ based on carbon paste electrode consisting of the room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate, multiwalled carbon nanotubes, silica nanoparticles and ionophore was constructed. The prepared composite has a low potential drift, high selectivity and fast response time, which leads to a more stable potential signal. A linear dynamic range of 4.50×10^?9–1.00×10^?1 mol L^?1 with a detection limit of 2.00×10^?9 mol L^?1 was obtained. The modified electrode was successfully applied to the accurate determination of trace amounts of Cd²⁺ in environmental and biological samples.