A 168-km ultra-long-range OTDR measurement at a wavelength of 1.55 μm

A Rayleigh backscattered signal and Fresnel reflection over a 167.6-km and a 251.2-km long pure silica-core fiber (PSF) with fiber loss 0.176 dB/km, and a 138.6-km and a 206.5-km long Ge-doped core dispersion shifted fiber (DSF) with fiber loss 0.218 dB/km have been observed with ultra-long-range optical time domain reflectometry (OTDR) using a 1.55-μm high-power semiconductor laser (LD) and InGaAs-APD with a low dark current at room temperature. The Rayleigh backscattered signal level and fiber loss are strongly dependent on the fiber dopant materials and fiber structural parameters. DSF gives a better SNR for short length fibers because the Rayleigh backscattered signal level is larger than PSF, but because the DSF loss is also larger, PSF gives a better SNR for fibers longer than the critical length. Accordingly, the dynamic range of OTDR in the different fiber types such as PSF and DSF becomes different. One-way backscattered dynamic ranges of 29.5 dB for the PSF and about 30.2 dB for the DSF at room temperature have been achieved.     

A 168-km ultra-long-range OTDR measurement at a wavelength of 1.55 μm

A Rayleigh backscattered signal and Fresnel reflection over a 167.6-km and a 251.2-km long pure silica-core fiber (PSF) with fiber loss 0.176 dB/km, and a 138.6-km and a 206.5-km long Ge-doped core dispersion shifted fiber (DSF) with fiber loss 0.218 dB/km have been observed with ultra-long-range optical time domain reflectometry (OTDR) using a 1.55-μm high-power semiconductor laser (LD) and InGaAs-APD with a low dark current at room temperature. The Rayleigh backscattered signal level and fiber loss are strongly dependent on the fiber dopant materials and fiber structural parameters. DSF gives a better SNR for short length fibers because the Rayleigh backscattered signal level is larger than PSF, but because the DSF loss is also larger, PSF gives a better SNR for fibers longer than the critical length. Accordingly, the dynamic range of OTDR in the different fiber types such as PSF and DSF becomes different. One-way backscattered dynamic ranges of 29.5 dB for the PSF and about 30.2 dB for the DSF at room temperature have been achieved.     

Fiber-optic delay line using multicore fiber

A fiber-optic delay line based on a multicore optical fiber is fabricated for the first time. Due to the optical pulse sequential passage over all cores, the time delay of the optical signal of 45.0 μs is obtained at the optical fiber length of only 1300 m. The use of the seven-core optical fiber allows a sevenfold reduction in the used fiber length in comparison with single-core fibers, which is promising for developing lines with long signal delays.     

Raman spectroscopy based on a single-crystal sapphire fiber

We demonstrate the advantages of using a single-crystal sapphire fiber to perform Raman spectroscopy over using a standard glass fiber. The narrow Raman peaks and the low background signal of a single-crystal sapphire fiber allow for the detection of weaker Raman signals or Raman signals much closer to the incident laser wavelength than with a standard glass fiber, which has a strong broadband Raman spectrum of its own. The Raman spectra of calcite, single-walled carbon nanotubes, and aqueous sodium carbonate solution were collected using a 50 cm long, 200 μm diameter sapphire fiber, and then they were compared with the results using a 50 cm long, 100 μm diameter glass fiber. The Raman spectrum of each tested material becomes indistinguishable due to the background Raman signal of the glass fiber but can easily be seen using the sapphire fiber, which has only a few narrow Raman peaks of its own.     

Single tone and multi tone microwave over fiber communication system using direct detection method

In this paper, an analog microwave over fiber link for long haul distance based upon Rate Equation Laser is demonstrated. This system uses the advantage of high potential bandwidth of fiber in transmission of microwave signal. The interface of the two systems needs an up-conversion of microwave band into baseband (at which fiber operates). An Intensity Modulation Direct Detection (IMDD) technique is used to achieve this purpose. The Rate Equation laser is operated in a dynamic state, where its intensity oscillates at a microwave frequency that varies with the input signal fed by wave generator. This system can also use for two modulating tones. The frequency of the first tone is varied from 1 to 20 GHz and second is set at 5 GHz. A data signal of 10 Gbps is transmitted over long haul single mode fiber by single tone system. A very good bit error rate (BER) 10^?40 performances for 100 km and 25 km fiber link is achieved for both single tone and two tones respectively in proposed microwave over fiber communication system.     

基于环形芯光纤的超低差分模式增益涡旋光纤放大器

提出了一种基于环形芯铒离子部分掺杂光纤的涡旋光纤放大器。针对该掺铒光纤的放大特性,研究了光纤长度、掺铒浓度与抽运功率对信号模式增益特性的影响。研究结果表明,该光纤放大器能够支持22个轨道角动量模式稳定传输,且C波段(1530~1565 nm)所有信号模式增益大于23 dB,信噪比高于27 dB,差分模式增益小于0.015 dB。所提出的基于环形芯光纤的涡旋光纤放大器具有支持轨道角动量模式数量多、差分模式增益低、信噪比高的优势,对于OAM复用长距离传输系统中的在线放大具有重要参考价值。     

一种新型基于并行光传输的HDMI线缆的研制

 介绍了一款基于并行光纤通信技术的高清视频信号(high-definition multimedia interface, HDMI）传输线缆的研制技术方案。这种新型HDMI线缆采用垂直腔面发射激光器(vertical cavity surface emitting laser, VCSEL）阵列作为发射端,光电探测器（photodiode, PD）阵列作为接收端,两者之间采用多模光纤阵列互连,通过将电信号转变为光信号传输解决了铜缆损耗对电信号传输速率和传输距离的限制。与铜缆HDMI线相比,这种新型HDMI线能够以4信道×3.4Gbps的传输速率实现长达300m的传输距离,为当前高清视频信号和下一代超高清视频信号远距离传输提供了可行的技术方案。     

Coherent transfer of an optical carrier over 251 km

We transfer an optical frequency over 251 km of optical fiber with a residual instability of 6x10(-19) at 100 s. This instability and the associated timing jitter are limited fundamentally by the noise on the optical fiber and the link length. We give a simple expression for calculating the achievable instability and jitter over a fiber link. Transfer of optical stability over this long distance requires a highly coherent optical source, provided here by a cw fiber laser locked to a high finesse optical cavity. A sufficient optical carrier signal is delivered to the remote fiber end by incorporating two-way, in-line erbium-doped fiber amplifiers to balance the 62 dB link loss.     

一种改进的双边带调制产生光毫米波的方案

提出了应用于光纤无线通信系统中一种改进的双边带调制产生光毫米波方案。在中心站采用强度调制将射频信号调制到光载波上产生一个双边带信号,滤掉中心载波后,利用光交叉复用器把双边带信号的上下边带模分开,将数据速率为2.5Gbit/s的基带信号调制到下边带模后,再与未调信号耦合后产生光毫米波,然后通过单模光纤传输至基站,在基站经过光电转换后产生电毫米波信号。从理论上对该毫米波的色散特性进行了分析,发现毫米波的接收功率不会周期的衰减。同时通过实验研究表明,下行链路信号通过光纤能传输50km而不需要色散补偿,功率代价小于1dBm。因此,该方法产生的光毫米波能有效克服光纤色散引起的信号时延而导致的基带信号退化,适合于远距离传输。     

基于扫描光纤激光器的光纤传感解调仪研究

介绍了一种基于扫描光纤激光器的光纤传感解调系统.采用氰化氢（HCN）气体吸收池作为波长参考基准,采用三次多项式拟合的方法来确定光纤F- P可调谐滤波器的波长与驱动电压的对应关系,可调谐滤波器扫描过程中对扫描电压、多路光谱信号进行同步采样,实时标定.实验结果表明,该解调系统在1 510 nm到1 590 nm波长范围内对FBG反射峰值波长的分辨率为1.4 pm,长期波长重复性达到3.2 pm.利用该系统实现了对FBG反射峰值波长和光纤EFPI传感器腔长的高准确度解调.     

Low noise gain-clamped L-band erbium-doped fiber amplifier by utilizing fiber Bragg grating

A novel gain-clamped long wavelength band (L-band) erbium-doped fiber amplifier (EDFA) is proposedand experimented by using a fiber Bragg grating (FBG) at the input end of the amplifier. This designprovides a good gain clamping and decreases noise effectively. It uses two sections of erbium-doped fiber(EDF) pumped by a 1480-nm laser diode (LD) for higher efficiency and lower noise figure (NF). The gainis clamped at 23 dB with a variation of 0.5 dB from input signal power of -30 to -8 dBm for 1589 nm andNF below 5 dB is obtained. At the longer wavelength in L-band higher gain is also obtained and the gainis clamped at 16 dB for 1614 nm effectively. Because the FBG injects a portion of backward amplifiedspontaneous emission (ASE) back into the system, the gain enhances 5 dB with inputting small signal.     

电光调制器输入端光纤温度对光纤频率调制光谱影响的研究

激光光谱技术由于其高灵敏、高分辨、可在线检测等优点被广泛的应用与痕量气体探测领域,而频率调制光谱(FMS)技术由于其除了探测灵敏度高的优点外且可同时探测气体样品的吸收和色散,通常还被应用于原子分子物理、量子光学等领域。发展全光纤FMS可以在保持气体探测灵敏度的同时有效简化实验装置,然而FMS是一项偏振态敏感技术,光纤温度变化等引起不适当的偏振态变化会诱发残余幅度调制(RAM),该RAM不仅使FMS线型扭曲,同时对其色散信号产生直流偏置,因此研究光纤温度对RAM特性的影响具有非常重要的意义。研究首先通过理论和实验验证了相位可控波片模型解释保偏光纤特性的可行性,然后实验测量了进入电光调制器(EOM)前保偏光纤温度对RAM的影响,发现由RAM引起的色散光谱直流偏置随温度呈正弦变化,且在24和26.8 ℃时直流偏置为零,即无RAM的状态,然而基于温度的直接RAM消除无法替代Wong-Hall提出的伺服反馈控制来实现其长期抑制,这种温度诱发RAM的变化也是所有FMS色散信号背景漂移的主要原因。     

(1+1)型长距离侧面泵浦光纤实现17.4 kW激光输出

长距离侧面泵浦激光光纤在泵浦光注入、热管理、非线性抑制等方面具有天然优势,是实现高功率激光输出的有效途径。研制了（1+1）型长距离侧面泵浦激光光纤,采用1018 nm同带泵浦反向注入方式实现了17.4 kW激光输出,斜率效率为82.1%,3 dB线宽为1.3 nm,拉曼抑制比为37.8 dB。研究结果展示了长距离侧面泵浦光纤作为数十千瓦光纤激光放大器增益介质的巨大应用潜力。     

混合结构的闭环光纤陀螺研究

提出并研制了混合结构的闭环光纤陀螺系统。详细分析了该系统的结构特点、信号检测方法以及反馈信号对系统的影响。该系统具有低损耗、长期低漂移特性。实现了３００ｄｅｇ．／ｓ的动态范围及小于３００×１０－６的线性误差。     

啁啾光纤光栅在光纤通信系统中的色散补偿

报道一个简单而新颖的、能将均匀光栅改变为线性啁啾光栅的方法,此方法可对光纤光栅的喃啾度和中心波长进行独立调节,实验表明,一长为１０ｃｍ的均匀光栅其啁啾度可增加至０．５ｎｍ／ｃｍ,而中心波长独立可调量达０．７ｎｍ利用这样的可调啁啾光栅在标准单模光纤（Ｇ６５２）中对一脉宽为２５ｐｓ的输入信号在１５５０ｎｍ窗口传输,成功地实现１００ｋｍ的色散补偿。     

短腔Er/Yb光纤光栅激光器

报道采用光敏Ｅｒ／Ｙｂ 光纤制作短腔Ｅｒ／Ｙｂ 光纤光栅激光器的实验结果。激光谐振腔由一对直接写在３０ ｍ ｍ 长的Ｅｒ／Ｙｂ 光纤上、长度分别为６ ｍ ｍ 及１０ ｍ ｍ 、反射率分别为９０％ 及９８．６％ 、３ ｄＢ带宽分别为０．２８ ｎｍ 及０．２６ ｎｍ 的光纤布拉格光栅组成, 激光器的泵浦阈值为８ｍ Ｗ, 斜效率约１４％ , 输出光的信噪比为６１ ｄＢ, 偏振模抑制比为３０ ｄＢ。     

Ultralong Raman fiber lasers as virtually lossless optical media

By transforming the optical fiber span into an ultralong cavity laser, we experimentally demonstrate quasilossless transmission over long (up to 75 km) distances and virtually zero signal power variation over shorter (up to 20 km) spans, opening the way for the practical implementation of integrable nonlinear systems in optical fiber. As a by-product of our technique, the longest ever laser (to the best of our knowledge) has been implemented, with a cavity length of 75 km. A simple theory of the lossless fiber span, in excellent agreement with the observed results, is presented.     

光纤光栅与受激布里渊信号的耦合特性

近年来,光纤布拉格光栅传感器与全分布式光纤传感器的融合技术受到了广泛关注,然而光纤布拉格光栅与布里渊信号之间的耦合特性鲜有报道。本文研究了光栅类型、波长、反射率及光纤的光致折射率对受激布里渊信号的影响规律,并探讨了空间分辨率对光纤布拉格光栅定位功能的影响。实验结果表明,在布里渊光时域分析系统中,光纤布拉格光栅处有尖锐的反射峰,而啁啾光栅、长周期光栅及光致折射率变化的光纤处均未出现尖锐的反射峰;光纤布拉格光栅反射率与受激布里渊散射功率谱无关;当光纤布拉格光栅的波长接近1 550 nm时,对受激布里渊频移测量的影响最大;在8 m的长度范围内,光纤布拉格光栅的定位误差约为4 cm,并且与空间分辨率无关。     

Bismuth-based erbium-doped fiber as a gain medium for L-band amplification and Brillouin fiber laser

Bismuth-based erbium-doped fiber (Bi-EDF) is demonstrated as an alternative medium for optical amplification and nonlinear applications. The bismuth glass host provides the opportunity to be doped heavily with erbium ions to allow a compact optical amplifier design. The bismuth-based erbium-doped fiber amplifier (Bi-EDFA) is demonstrated to operate at wavelength region from 1570 to 1620 nm using only a 215 cm long of gain medium. The maximum gain of 15.8 dB is obtained at signal wavelength of 1610 nm with the corresponding noise figure of about 6.3 dB. A multi-wavelength laser comb is also demonstrated using a stimulated Brillouin scattering in the 215 cm long Bi-EDF assisted by the 1480 nm pumping. The laser generates more than 40 lines of optical comb with a line spacing of approximately 0.08 at 1612.5 nm region using 152 mW of 1480 nm pump power.     

Impact of fiber delay fluctuation on reference injection-locked optoelectronic oscillators

We demonstrate that the phase shift of a reference injection-locked optoelectronic oscillator (OEO) varies as the change of its fiber delay over a long period of time. The dynamic variation of the fiber delay is monitored using an injected probe signal and is compared with the phase shift. With actively stabilized fiber delays according to the monitored data, the long-term frequency stability of the reference injection-locked OEO is evaluated.