Polypyrrole on self-assembled monolayers of a pyrrolyl lipoic acid derivative—electrosynthesis and polymer film characterization

The electropolymerization of pyrrole on gold modified by a self-assembled monolayer (SAM) of a pyrrolyl lipoic acid derivative was investigated in detail and the results compared to those obtained on bare substrates. Both under potentiostatic and potentiodynamic control, a slight blocking action of the underlying SAM could be observed for the initial stages of polymer growth but thereafter the electrochemical features were similar to those collected for polypyrrole (PPy) deposition on bare gold. The morphology and structure of PPy films formed on the SAMs were characterized by atomic force microscopy and X-ray diffraction, which revealed that those polymer properties are much more influenced by the electrochemical mode of preparation, than by the underlying SAMs. While, when compared to PPy on bare gold, no effect has been detected on thin layers deposited at constant potential, surface areas with rather irregular morphology, as well as a small but beneficial influence in inducing order on the first few layers of the polymer film, have been observed on similar films formed by cyclic voltammetry. The typical globular morphology of PPy has always been observed for relatively thick layers in which the redox behavior, analyzed by in situ AFM, showed an increase in volume of the polymer nodules upon reduction, largely due to the SAM reorganization induced by the applied potential.     

铂-氧化铈/聚苯胺/聚砜复合膜电极的制备及对甲醇的电催化氧化

采用电化学聚合法制备了掺杂CeO2纳米粒子的聚苯胺(PAN)/聚砜(PSF)复合膜电极,在其上电沉积铂粒子,制得了铂-氧化铈/聚苯胺/聚砜的复合膜修饰电极。 复合膜的形貌和化学组分通过冷场发射扫描电子显微镜（Cold FE-SEM）和能量散射X射线谱（EDS）进行了表征,用循环伏安法和电化学交流阻抗法考察了复合膜电极对甲醇的电催化氧化性能。 结果表明,复合膜的双层多孔结构使铂粒子与CeO2粒子在复合膜内层的多孔聚苯胺上均匀沉积,粒子平均尺寸约为80 nm;CeO2为铂质量的7%时,铂-氧化铈/聚苯胺/聚砜复合膜修饰电极对甲醇有很好的电催化氧化性能和高的稳定性。     

Surface modification and functionalization through the self-assembled monolayer and graft polymerization

The modification of a surface at the molecular level with precise control of the building blocks generates an integrated molecular system. This field has progressed rapidly in recent years through the use of self-assembled monolayer (SAM) interfaces. Recent developments on surface-initiated chemical reactions, functionalization, and graft polymerization on SAM interfaces are emphasized in the present review. A number of surface modifications by grafting are reviewed. The grafting of polyaniline on a glass surface, previously modified with a silane self-assembled monolayer (SAM), is examined in detail for both planar and 3-D systems, such as fibers, nanoparticles, and even polymer patterned surfaces. We also discuss the graft polymerization of water-soluble polymers on the surface of silicon nanoparticles, which generate stable aqueous colloidal solutions and have numerous applications. Finally, we compare and review some surface-modification techniques on the surfaces of polymers, such as two-solvent entrapment, polymer blending, and chemical grafting, which improve their biocompatibility.     

Platinum-modified polyaniline/polysulfone composite film electrodes and their electrocatalytic activity for methanol oxidation

The polyaniline/polysulfone (PAN/PSF) composite films were prepared by electropolymerization, and then platinum was deposited into this composite film to obtain the platinum-modified polyaniline/polysulfone(Pt/PAN/PSF) composite film electrodes. Their component, morphology and structure were characterized by FTIR spectra, scanning electron microscopy and energy dispersive X-ray spectroscopy. The results show that the composite film has a bi-layer structure with asymmetrical pores, and the platinum particles are homogeneously dispersed in the modified film electrodes. The cyclic voltammetry and electrochemical impedance spectroscopy techniques were applied to investigate the electrochemical properties and the electrocatalytic activity of the modified film electrodes, which show a promotive action for methanol oxidation and the methanol oxidation under a diffusion-controlled process.     

The mycological effect on morphological,electrochemical and redox properties of the polyaniline surface

Biofilm formation with eight different microscopic fungi on the polyaniline surface and its effect on the morphological, electrochemical and redox properties have been studied. The investigations on selected Chrysosporium merdarium and Rhizomucor pusillus fungi behavior were performed. Conspicuous difference in the oxidation level, redox activity and oxalate impurities at the polymer surface layer treated with Chrysosporium merdarium and Rhizomucor pusillus was confirmed. The electrochemical behavior of the modified electrode was characterized using the cyclic voltammetry technique. The chemical composition of treated surface was determined by X‐ray photoelectron spectroscopy. For the estimation of conductive polymer morphology and roughness, the method of optical and scanning probe microscopy was applied, which showed that the polyaniline surfaces treated with Chrysosporium merdarium are homogenous and smoother than the polyaniline surfaces treated with Rhizomucor pusillus. Water contact angle measurements confirmed the effect of microbial growth on the properties of the polyaniline surface. Copyright © 2013 John Wiley & Sons, Ltd.     

Chemical and physical modification and electret properties of polytetrafluoroethylene films

Composites with titanium oxide structures on the surface of a polymer matrix were prepared by preliminary plasma activation of polytetrafluoroethylene films, followed by chemical treatment with vapors of titanium tetrachloride and water. The chemical composition and structure of the modified film surface were studied by scanning electron microscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. The stability of the formed surface charge increases in going from the initial film to the plasma-activated film, then to the film successively treated with vapors of titanium tetrachloride and water, and finally to the plasma-activated film treated subsequently with vapors of titanium tetrachloride and water. The modified polytetrafluoroethylene films are of interest as electrets with enhanced operation characteristics.     

Direct electrochemistry of cytochrome c immobilized on a novel macroporous gold film coated with a self-assembled 11-mercaptoundecanoic acid monolayer

We have successfully constructed a novel gold film with open interconnected macroporous walls of nanoparticles by combining the hydrogen bubble dynamic template synthesis with galvanic replacement reaction. After modified by a self-assembled monolayer (SAM) of 11-mercaptoundecanoic acid (MUA), the three-dimensionally (3D) interconnected macroporous Au film has been used as a biocompatible substrate for the immobilization of cytochrome c. The morphology, structure and electrochemical features of the modified and unmodified macroporous Au films were characterized by field-emission scanning electron microscopy (FESEM), energy-dispersive X-ray (EDX), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results reveal that the resultant films had a large electroactive surface area for high protein loading, enhanced electron transfer of cytochrome c, retained electrochemical activity, good stability and repeatability. And the excellent electrochemical behaviors could be attributed to the hierarchical structure of the macroporous Au film constructed by nanoparticles.     

An inkjet printing soft photomask and its application on organic polymer substrates

This article presents a simple, fast and low-cost method to fabricate a flexible UV light photomask. The designed micropatterns were directly printed onto transparent hybrid composite film of biaxially oriented polypropylene coated with silica oxide (BOPP-SiO _x ) by an inkjet printer. Compared to the conventional chrome-mask, it is of advantages such as suitable for non-planar substrates, scalable for large area production, and extreme low cost. Combined with the confined photo-catalytic oxidation (CPO) reaction, the printed flexible BOPP-SiO _x photomask was successfully used to pattern the shape of wettability of organic polymer surfaces, and then polyaniline patterns were deposited on the modified substrates with strong adhesion. With the above photomasks, the polyacrylic acid graft chains were duplicated on the poly (ethylene terephthalate) (PET) and BOPP substrates by photografting polymerization. We grafted polyacrylic acid (PAA) on a non-planar plastic substrate with this soft and thin plastic photomask. Scanning electron microscopy (SEM) and optical microscopy were used to characterize the surface morphology and thickness of ink layers of the printed photomask. Optical microscopy was used to characterize the deposition polyaniline micropatterns. It was found that the desired patterns were precisely printed on the modified polymer films and were applied in modifying organic polymer substrates. The printed photomask could be exploited in the fields such as prototype microfluidics, micro-sensors, optical structures and any other kind of microstructures which does not require high durability and dimensional stability.     

聚苯胺/聚砜复合材料的制备及其超级电容性能

通过化学聚合法,制备出盐酸掺杂聚苯胺（PANI）,将其与聚砜（PSF）溶液混合,定量滴加到玻碳电极上制得PANI/PSF复合膜电极。 采用扫描电子显微镜、红外光谱以及X射线衍射对其结构和形貌进行表征。 根据循环伏安曲线、恒电流充放电曲线和电化学阻抗,研究了其作为电极的超级电容性能。 结果表明,多孔结构的PANI/PSF复合材料具有良好的电容性能,其比电容可达到497 F/g,并且该超级电容器具有较小的内阻和较好的循环稳定性。     

DNA在氨基功能化偶氮苯自组装膜表面的固定

采用简单快速的方法制备出将DNA固定在其表面的单分子层敏感膜.首先采用表面自组装技术将硅氧烷基偶氮苯衍生物H2NAzoCONHC3Si(OCH3)3(APDA-N-TMSPBA)组装在硅表面,在详细考察单分子层薄膜的化学结构、表面浸润性和分子表面形貌之后,又通过紫外吸收光谱(UV)在位考察了硅氧烷基偶氮苯衍生物的光学异构特性.在DNA在自组装薄膜固定后,X光电子能谱仪(XPS)结果显示出现了明显的磷元素信号,表明DNA分子可以成功固定在自组装膜表面.     

循环伏安法的电扫描方式对苯胺聚合产物形貌影响的观察

在含有0.2 mol.L-1苯胺的0.5 mol.L-1H2SO4溶液中,以扫描速度50 mV.s-1,扫描电位为-0.1~0.9 V,采用循环伏安法(CV),在金属Ti基体上,通过控制扫描方式分别得到了颗粒状、纤维状及管-片状的苯胺聚合产物,分析了形成不同形貌聚苯胺的原因,并通过扫描电子显微镜(SEM)、循环伏安法和电化学阻抗谱(EIS)对不同形貌聚苯胺的结构和性能进行了表征.结果表明,不同形貌聚苯胺的形成是由于聚苯胺的成核及生长模式不同,而无论何种形貌的聚苯胺膜都具有很大的比表面积和良好的导电性能,其中,管-片状聚苯胺的膜层阻抗最小,导电性能最好.     

Preparation and characterization of ultrathin dual-layer ionic liquid lubrication film assembled on silica surfaces

A novel ultrathin dual-layer film, which contained both bonded and mobile phases in ionic liquids (ILs) layer, was fabricated successfully on a silicon substrate modified by a self-assembled monolayer (SAM). The formation and surface properties of the films were analyzed using ellipsometer, water contact angle meter, attenuated total reflectance Fourier transform infrared spectroscopy, multi-functional X-ray photoelectron spectroscopy, and atomic force microscope. Meanwhile, the adhesive and nanotribological behaviors of the films were evaluated by a homemade colloidal probe. A ball-on-plate tribometer was used to evaluate the microtribological performances of the films. Compared with the single-layer ILs film deposited directly on the silicon surface, the as-prepared dual-layer film shows the improved tribological properties, which is attributed to the special chemical structure and outstanding physical properties of the dual-layer film, i.e., the strong adhesion between bonded phase of ILs and silicon substrate via the chemical bonding with SAM, the interlinked hydrogen bonds among the molecules, and two-phase structure composed of steady bonded phase with load-carrying capacity and flowable mobile phase with self-replenishment property.     

Methylene blue and neutral red electropolymerisation on AuQCM and on modified AuQCM electrodes: an electrochemical and gravimetric study

The phenazine monomers neutral red (NR) and methylene blue (MB) have been electropolymerised on different quartz crystal microbalance (QCM) substrates: MB at AuQCM and nanostructured ultrathin sputtered carbon AuQCM (AuQCM/C), and NR on AuQCM and on layer-by-layer films of hyaluronic acid with myoglobin deposited on AuQCM (AuQCM-{HA/Mb}(6)). The surface of the electrode substrates was characterised by atomic force microscopy (AFM), and the frequency changes during potential cycling electropolymerisation of the monomer were monitored by the QCM. The study investigates how the monomer chemical structure together with the electrode morphology and surface structure can influence the electropolymerisation process and the electrochemical properties of the phenazine-modified electrodes. Differences between MB and NR polymerisation, as well as between the different substrates were found. The electrochemical properties of the PNR-modified electrodes were analysed by cyclic voltammetry and electrochemical impedance spectroscopy and compared with the unmodified AuQCM. The results are valuable for future applications of modified AuQCM as substrates for electroactive polymer film deposition and applications in redox-mediated electrochemical sensors and biosensors.     

The influence of diamond blend on the resistance of polyimide films to atomic oxygen

Poly-pyromellitimide and polyamideimide film samples and their modifications obtained with a carbon filler (diamond blend) were irradiated with atomic oxygen flow at an average particle energy of 20 eV. Weight erosion coefficients were calculated for the initial and modified polyimides and a comparative analysis of the resistance of the film samples was carried out. The morphology of the film surface was studied after irradiation with atomic oxygen via scanning electron microscopy. An increase in the percentage of filler in the polymer matrix caused a slight increase in the resistance of the film samples to the effect of atomic oxygen.     

Amplified Electrochemical DNA Sensor Based on Polyaniline Film and Gold Nanoparticles

In this work, an electrochemical DNA biosensor, based on a dual signal amplified strategy by employing a polyaniline film and gold nanoparticles as a sensor platform and enzyme‐linked as a label, for sensitive detection is presented. Firstly, polyaniline film and gold nanoparticles were progressively grown on graphite screen‐printed electrode surface via electropolymerization and electrochemical deposition, respectively. The sensor was characterized by scanning electron microscopy (SEM), cyclic voltammetry and impedance measurements. The polyaniline‐gold nanocomposite modified electrodes were firstly modified with a mixed monolayer of a 17‐mer thiol‐tethered DNA probe and a spacer thiol, 6‐mercapto‐1‐hexanol (MCH). An enzyme‐amplified detection scheme, based on the coupling of a streptavidin‐alkaline phosphatase conjugate and biotinylated target sequences was then applied. The enzyme catalyzed the hydrolysis of the electroinactive α‐naphthyl phosphate to α‐naphthol; this product is electroactive and has been detected by means of differential pulse voltammetry. In this way, the sensor coupled the unique electrical properties of polyaniline and gold nanoparticles (high surface area, fast heterogeneous electron transfer, chemical stability, and ease of miniaturisation) and enzymatic amplification. A linear response was obtained over a concentration range (0.2–10 nM). A detection limit of 0.1 nM was achieved.     

Surface modification of poly(tetrafluoroethylene) films by plasma polymerization of glycidyl methacrylate and its relevance to the electroless deposition of copper

Surface modification of poly(tetrafluoroethylene) films by plasma polymerization and deposition of glycidyl methacrylate (GMA) was carried out. The effects of glow‐discharge conditions on the chemical structure and composition of the deposited GMA polymer were analyzed by X‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscopy. XPS and FTIR results revealed that the epoxide groups in the plasma‐polymerized GMA (pp‐GMA) layer had been preserved to various extents, depending on the plasma deposition conditions. The morphology of the modified PTFE surface was investigated by atomic force microscopy (AFM). The pp‐GMA film with well‐preserved epoxide groups was used as an adhesion promotion layer to enhance the adhesion of the electrolessly deposited copper on the PTFE film. The T‐peel adhesion test results showed that the adhesion strength between the electrolessly deposited copper and the pp‐GMA‐modified PTFE (pp‐GMA‐PTFE) film was much higher than that between the electrolessly deposited copper and the pristine or the Ar plasma‐treated PTFE film. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3498–3509, 2000     

Spectroscopy of thin polyaniline films deposited during chemical oxidation of aniline

Any surface immersed in the aqueous reaction mixture used for the preparation of polyaniline becomes coated with a polyaniline film of submicrometre thickness. In this way, various materials can be modified by an overlayer of conducting polymer. The present review illustrates the role of infrared, Raman, and UV-VIS spectroscopies in the studies of polyaniline film growth. Spectroscopic methods are crucial in the evaluation of the performance of polyaniline films alone or in combination with nanoparticles of noble metals. The assessment of film ageing and stability can be followed conveniently by these methods. Carbonization of polyaniline films to nitrogen-containing carbon analogues is also discussed.     

Strong adhesion and smooth conductive surface via graft polymerization of aniline on a modified glass fiber surface

The goal of this paper is to prepare surface-conductive glass fibers. The fibers were first hydroxylated, after which they were reacted with 3-bromopropyltrichlorosilane to form a bromopropylsilane monolayer, which was further reacted with aniline to substitute the bromine atoms. The surface-bound aniline molecules were used as active sites for the graft polymerization of polyaniline (PANI). The composition, structure and the morphology of the modified glass fiber surface were examined by X-ray photoelectron spectroscopy, scanning electron microscopy, and Fourier transform infrared spectroscopy. The method generated a smooth and homogenous thin layer of PANI on the surface of the glass fiber with a surface conductivity of about 6 S/cm, hence larger than the usual value ( approximately 1 S/cm) of the bulk polyaniline.     

Flexible polyaniline

Flexible polyaniline having excellent mechanical properties (e.g., elongation at break = 41% and tensile strength = 1.8 kg cm^?2) was prepared by electrochemical reduction of ordinary polyaniline in organic solvents. The flexibility is directly related with the polymer morphology which was definitely affected by the nature of electrolyte anion. Perchlorate or tetrafluoroborate anion were found suitable to obtain flexible polyaniline. At the same time, it is essential that the polymer so prepared should be reduced (undoped) in some suitable organic solvents before making a flexible free standing film.