Catalysts based on cordierite modified with transition metal oxides

Catalysts active in ammonia oxidation have been obtained by the substitution of transition metal (Mn, Fe, Co, Ni, and Cu) ions for Mg ions in the cordierite structure 2MgO · 2Al₂O₃ · 5SiO₂ at 1100°C. Their phase composition, texture, and activity depend on the type and amount of introduced transition metal oxide. The Mn- and Cu-containing catalysts, which consist of substituted cordierites 2(Mg_{1 ? x} M _x )O · 2Al₂O₃ · 5SiO₂ and Mn₂O₃ or CuO crystallites located on their surface, are most active in ammonia oxidation. The catalysts are characterized by a small specific surface area and have large pores, whose total volume is small. The Fe-containing catalysts consist of the Fe-substituted cordierite phase and particles of an iron oxide phase. These particles are mostly located in internal pores of the catalysts and are, therefore, hardly accessible to ammonia molecules. The introduction of Co or Ni oxide leads to the formation of a low-active spinel phase rather than the cordierite phase.     

Untersuchungen im System SrO?SiO2?H2O

Investigation on the System SrO? SiO₂? H₂O On addition sodium silicate solutions to solutions of Sr(OH)₂, at room temperature strontium hydrogensilicates are precipitated which are always amorphous and contain silicate anions of various condensation degrees. At about 100°C at first also amorphous products are formed containing lower- and higher-molecular silicate anions. On standing of these precipitates at about 80°C under the mother liquor, however, cristallization occurs under complete degradation of the higher-molecular anions to monomeric resp. dimeric silicate anions. In dependence on the Na₂O: SiO₂ ratio of the sodium silicate solutions and on the Sr(OH)₂ concentrations the following crystalline compounds are formed: 1.25 SrO · 1 SiO₂ · 2 H₂O, 3 SrO · 2 SiO₂ · 3 H₂O and 3 SrO · 2 SiO₂ · 4 H₂O, with monomeric silicate anions; 2 SrO · 2 SiO₂ · 1.5 H₂O; 2 SrO · 2 SiO₂ · 2 H₂O, and 2 SrO · 2 SiO₂ · 3 H₂O, with dimeric anions.     

Preparation of Au Nanoparticles on Surface of Two Supports by Adsorption Phase Synthesis

By utilizing adsorption phase synthesis (APS), Au nanoparticles were prepared on the surface of SiO₂ with or without modification by Ni(OH)₂. TEM, XRD, and UV‐vis were employed to characterize the morphology of Au particles on the surface of two kinds of supports. The results showed that the average size of Au particles on the SiO₂ surface modified by Ni(OH)₂ was less than 5 nm. Due to high surface isoelectric point, Au particles formed in the adsorption layer were prone to distribute on the surface of SiO₂ modified by Ni(OH)₂. With content of Ni(OH)₂ in samples increasing, more Au particles with small size appeared on the support surface.     

Kinetics of the gas‐phase reactions of hydroxyl radicals with C1–C6 aliphatic alcohols in the presence of ammonium sulfate aerosols

The effects of ammonium sulfate aerosols on the kinetics of the hydroxyl radical reactions with C₁–C₆ aliphatic alcohols have been investigated using the relative rate technique. P‐xylene was used as a reference compound for the C₂–C₆ aliphatic alcohols study, and ethanol was used as a reference compound for the methanol study. Two different aerosol concentrations that are typical of polluted urban conditions were tested. The total surface areas of aerosols were 1400 μm² cm^?3 (condition I) and 3400 μm² cm^?3 (condition II). Results indicate that ammonium sulfate aerosols promote the ethanol/OH radical and 1‐propanol/OH radical reactions as compared to the p‐xylene/OH radical reaction. The relative rate of the ethanol/·OH reaction versus the p‐xylene/·OH reaction increased from 0.19 ± 0.01 in the absence of aerosols to 0.24 ± 0.01 and 0.26 ± 0.02 under aerosol conditions I and II, respectively. The relative rate of the 1‐propanol/·OH reaction versus the p‐xylene/·OH reaction increased from 0.45 ± 0.03 in the absence aerosols to 0.56 ± 0.02 and 0.55 ± 0.03 under aerosol conditions I and II, respectively. However, significant changes in the relative rates of the 1‐butanol/·OH, 1‐pentanol/·OH, and 1‐hexanol/·OH reactions versus the p‐xylene/·OH reaction were not observed for either aerosol concentration. The relative rates of the methanol/·OH reaction versus the ethanol/·OH reaction were identical in the absence and presence of aerosols. These results indicate that ammonium sulfate aerosols promote the methanol/·OH reaction as much as the ethanol/·OH reaction (as compared to the p‐xylene/·OH reaction). © 2001 John Wiley & Sons, Inc. Int J Chem Kinet 33: 422–430, 2001     

Low-energy fragmentations of five isomeric [H3, C,N, O2] +· ions

The low-energy fragmentation characteristics of the [H₃,C,N,O₂]^+· isomers [H₃CNO₂]^+· (a), [H₂C?N(O)OH]^+· (b), [H₃CONO]^+· (c), [HC(O)NHOH]^+· (d) and [HC(OH)?NOH]^+· (e) were studied in detail by metastable ion mass spectrometry. In agreement with most earlier observations, appearance energy measurements established the potential energy surface of the isomers a, b and c, showing the intricate interrelations between them. It was concluded that a isomerizes into b prior to fragmentation by loss of ^·OH and H₂O and into c before loss of ^·H and H₃CO^· moreover, the reverse reactions do not take place on the metastable time-frame. The dominant metastable process for isomers d and e (obtained via HCN loss from glyoxime) was generation of [H₂NOH]^+·. For isomer e this process was proposed to involved a rate-determining isomerization into d. It was concluded that isomers d and e do not intercommunicate with ions a, b and c prior to fragmentation. Neutralization-reionization mass spectrometry indicated that the enol form of formohydroxamic acid as well as the keto counterpart are stable in the gas phase.     

SiO2@AgCl:Ag纳米复合材料:一种可见光催化降解罗丹明B的高效等离子体光催化剂

采用多元醇沉淀以及光化学还原法制备了SiO₂担载AgCl:Ag等离子体纳米粒子。通过表征发现SiO₂@AgCl:Ag粒子呈立方-四足角状。同时,由于表面Ag簇的等离子共振效应,该催化剂在可见光区有很强的光吸收,可用于在高效降解稳定的有机染料,例如,罗丹明B。合成的SiO₂@AgCl:Ag复合催化剂可在2 min内将罗丹明B分子完全降解。自由基捕获实验进一步探究发现O₂·^-和·OH是参与降解反应的主要氧化活性物种。以上SiO₂@AgCl:Ag的这些特性使其在水净化和环境治理方面有着潜在的应用。     

Iron adsorption on SiO2/Si(111)

The adsorption of ferric and ferrous iron onto the native oxide of the SiO₂/Si(111) surface has been evaluated using X‐ray photoelectron spectroscopy (XPS). Through a series of immersion experiments, performed at room temperature and pH 1, it has been shown that the ferric species is strongly adsorbed onto the hydrophilic surface, while ferrous iron remains in solution. Dehydroxylation of the silica surface by etching with hydrofluoric acid reduces the concentration of receptive Si‐OH groups, thereby limiting iron adsorption. The experiments were reproduced in a combined ultrahigh vacuum‐electrochemical system (UHV‐EC), which allowed a carbon‐free surface to be prepared before contacting the iron solutions, and confirmed the strong affinity of ferric iron towards the SiO₂/Si(111) surface. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation and properties of silylated PTFE/SiO2 organic–inorganic hybrids via sol–gel process

A study on poly(tetrafluoroethylene) (PTFE) reinforced with tetraethoxysilanes (TEOS) derived SiO₂ is described. It included the manufacturing process of SiO₂‐reinforced PTFE and the effects of silylation agent on the properties of the hybrid material, such as porosity, hydrophobic, thermal resistance, dielectric and mechanical properties, and microstructure. PTFE/SiO₂ hybrids of 50 wt % SiO₂ loading were prepared via a sol–gel process and were shaped by a two‐roll milling machine. Trimethylchlorosilane and hexamethydisilazane were used as the silylation agents. Our results showed that the water absorption and dielectric loss of PTFE/SiO₂ hybrid had significantly improved with silylation agent. The silylation process replaced Si? OH with Si? CH₃ on the surface of the TEOS‐derived silica colloidal particle. The existence of trimethylsilyl [? Si(CH₃)₃] on the surface of the modified PTFE/SiO₂ hybrid was confirmed via infrared and solid‐state ²⁹Si magic‐angle spinning nuclear magnetic resonance spectra. Nitrogen‐sorption techniques were used to characterize the modified and unmodified PTFE/SiO₂ hybrids. The microstructure of SiO₂ in the matrix was also evaluated with scanning electron microscopy and transmission electron microscopy. Our results showed that the silylated sol–gel‐derived PTFE/SiO₂ hybrids had exhibited high porosity (53.7%) with nanosize pores (10–40 nm) and nanosize colloidal particles (20–50 nm). This manifests itself as have the ultralow dielectric properties (D_k = 1.9 and D_f = 0.0021), low coefficient of thermal expansion (66.5 ppm/°C), high tensile modulus (141 MPa), excellent thermal resistance (T_d = 612 °C), and an increased hydrophobia (θ = 114°); moreover, the hydrophobic property of the PTFE/SiO₂ hybrid was thermally stable up to 400 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1789–1807, 2004     

Untersuchung von Hydrolysereaktionen zum Aufbau von Eisen(III)‐Oxo‐Aggregaten

Investigation of the Hydrolytic Build‐up of Iron(III)‐Oxo‐Aggregates The synthesis and structures of five new iron/hpdta complexes [{Fe^III₄(μ‐O)(μ‐OH)(hpdta)₂(H₂O)₄}₂Fe^II(H₂O)₄]·21H₂O ( 2 ), (pipH₂)₂[Fe₂(hpdta)₂]·8H₂O ( 4 ), (NH₄)₄[Fe₆(μ‐O)(μ‐OH)₅(hpdta)₃]·20.5H₂O ( 5 ), (pipH₂)_1.5[Fe₄(μ‐O)(μ‐OH)₃(hpdta)₂]·6H₂O ( 7 ), [{Fe₆(μ₃‐O)₂(μ‐OH)₂(hpdta)₂(H₄hpdta)₂}₂]·py·50H₂O ( 9 ) are described and the formation of these is discussed in the context of other previously published hpdta‐complexes (H₅hpdta = 2‐Hydroxypropane‐1, 3‐diamine‐N, N, N′, N′‐tetraacetic acid). Terminal water ligands are important for the successive build‐up of higher nuclearity oxy/hydroxy bridged aggregates as well as for the activation of substrates such as DMA and CO₂. The formation of the compounds under hydrolytic conditions formally results from condensation reactions. The magnetic behaviour can be quantified analogously up to the hexanuclear aggregate 5 . The iron(III) atoms in 1 ‐ 7 are antiferromagnetically coupled giving rise to S = 0 spin ground states. In the dodecanuclear iron(III) aggregate 9 we observe the encapsulation of inorganic ionic fragments by dimeric{M₂hpdta}‐units as we recently reported for Al^III/hpdta‐system.     

Formation of interstellar vinyl alcohol via simple radical processes: Theoretical study

Density functional theory calculations at the B3LYP/6‐31++G(d,p) level of theory were employed to verify whether the formation of vinyl alcohol (VA) in the interstellar medium can be explained by reactions of common and abundant interstellar species such as acetylene, radicals C₂, HC? C · , · OH, and H · . Several reaction sequences are possible. They include radical combinations, which proceed without activation barriers and are highly exothermic. The reactions of closed‐shell species acetylene and HC?C‐OH with hydrogen atoms, as well as H‐transfer and OH‐rotation processes, might require activation energy. Nevertheless, either the corresponding transition states lay below the reactant level or there are alternative routes that involve no transition states at all, such as the reaction sequences C₂ → HC?C · → HC?CH → trans‐syn‐HC( · )?CH‐OH → syn‐VA; C₂ → HC?C · → syn‐?C?CH‐OH → (trans or cis)‐syn‐HC( · )?CH‐OH → syn‐VA; and C₂ → · C?C‐OH → syn‐:C?CH‐OH → (trans or cis)‐syn‐HC( · )?CH‐OH → syn‐VA. © 2003 Wiley Periodicals, Inc. Int J Quantum Chem, 2004     

The protection effect of β-CD on DNA damage induced by ultrafine TiO2

Under the photocatalysis of 365 nm ultraviolet radiation, ultrafine TiO2 caused the oxidative damage of Teasy plasmid DNA. The damage was determined by gel-electrophoresis. Then, a different dose of β-CD was added to the reaction, and the damage was restrained. The rate of damage restraining reached 97% when the mass of β-CD was 4 times as that of TiO2. Through UV scan and IR spectroscopy, it was found that the Ti-O of ultrafine TiO2 was bound with -OH of β-CD cavum and the -OH on the surface of ultrafine TiO2 disappeared, so the formation of · OH was controlled. The ultrafine TiO2 has been widely used, but it was determined to be carcinogenic by some research. The protection effect of β-CD to DNA in the molecular level takes a new look on the surface modification of nano particles to decrease the toxic effect.     

Solid mechanochemical preparation of core‐shell SiO2 particles and their improvement on the mechanical properties of PVC composites

In this article, a solid mechanochemical route to prepare core‐shell structured particles was introduced. X‐ray photoelectron spectrum, transmission electron microscope and dissolving experimental results indicated the formation of [(inorganic particle)/(elastomer)] core‐shell structured particles. The thermal stable experiments showed that untreated SiO₂ can cause dehydrochlorination of poly(vinyl chloride) (PVC) and discoloration of PVC/SiO₂ composites and the formation of core‐shell structured SiO₂ particles will improve the thermal stability of PVC/SiO₂ composites. The mechanical properties and rheological results showed that the formation of core‐shell structured SiO₂ particles can both improve the mechanical and processing properties of PVC/SiO₂ composite. ACR in PVC/(SiO₂‐PMMA‐ACR) composites acted not only as toughener for PVC matrix but also as cushion breaker if the content of ACR is enough. Meanwhile compared with other SiO₂ particles the formation of core‐shell structured SiO₂ particles can decrease the apparent viscosity, increase the critical shear rate and improve the appearance of extrudes of PVC/SiO₂ composites. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 938–948, 2008     

The effect of iron phosphate,alumina and silica coatings on the morphology of carbonyl iron particles

Carbonyl iron powders were coated with iron phosphate using phosphating method and boehmite (γ‐AlOOH) or silicon hydroxide (Si(OH)₄) nanoparticles derived from the hydrolysis of tri‐sec‐butoxide (Al(OC₄H₉)₃) or tetramethylsilane (Si(OCH₃)₄) using sol–gel method. The coated powders were dried and calcined at 400 °C for 3 h in air. Cross‐section morphology of coated carbonyl iron powders were investigated by scanning electron microscopy energy dispersive X‐ray analysis. Coated Fe micro‐particles were spherical in shape with ‘shell/core’ structures. The shells consisted of an amorphous layer with varying thickness (100–800 nm) and the core represented a carbonyl iron. Gelatinous morphology of dried FePO₄ coating composed from nanoparticles of iron oxyhydroxides and hydrated iron phosphate with a shell thickness of ～100 nm around iron particles was observed. In coatings based on alumina or silica xerogels with a thickness of ～100–150 nm or ～200–500 nm, the coatings were composed of iron oxyhydroxides and γ‐AlOOH or Si(OH)₄. The resulting XRD diffractograms revealed the hematite (α‐Fe₂O₃) and magnetite (Fe₃O₄) that were formed in phosphated and sol–gel coated iron powders. The X‐ray diffraction patterns did not verify the presence of phosphates, alumina or silica and indicate the amorphous or nanocrystalline structure of FePO₄, γ‐Al₂O₃ and SiO₂. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation and Evaluation of Octadecyl-Bonded ZrO2/SiO2

ZrO₂/SiO₂ particles, which were prepared by a layer-by-layer self-assemble technique and consist of micrometer-sized silica spheres as cores and nanometer-sized zirconia particles as surface coatings, have a higher surface area and pore volume than other zirconia supports have. Further more it is more stable than silica is. In this paper we made a reversed-phase support by bonding octadecyltrichlorosilane on ZrO₂/SiO₂ particles, it had a comparable high carbon amount of 9.62% and good chemical stability being stable up to pH 11. The chromatographic behavior showed that the support acted as a true reversed chromatographic stationary phase and had a hydrophobic selectivity. Basic and aromatic compounds are well separated and the peaks are symmetrical.     

Devitrification behaviour of CaO−MgO(Y2O3)−SiO2 glasses

In this paper a thermoanalytical study of the kinetic parameters and mechanism of the devitrification process of CaO·SiO₂, 1.6CaO·0.4MgO·2SiO₂ and 1.4CaO·(0.6/3)Y₂O₃·2SiO₂ is reported. The experimental results suggest that, in the studied glasses, a surface nucleation process is operative; however, in finely powdered samples, that soften and efficiently sinter before devitrifying, surface nuclei behave as bulk nuclei. In this case lamellar crystalline structures are obtained.     

Resonance scattering spectral detection of ultratrace IgG using immunonanogold-HAuCl<Subscript>4</Subscript>-NH<Subscript>2</Subscript>OH catalytic reaction

Nanogold particles of 10 nm were used to label goat anti-human IgG (GIgG) to obtain nanogold-labeled GIgG (AuGIgG). In a citrate-HCI buffer solution of pH 2.27, AuGIgG showed a strong catalytic effect on the reaction between HAuCl₄ and NH₂OH to form big gold particles that exhibited a resonance scattering (RS) peak at 796 nm. Under the chosen conditions, AuGIgG combined with IgG to form immunocomplex AuGIgG-IgG that can be removed by centrifuging at 16000 r/min. AuGIgG in the centrifuging solution also showed catalytic effect on the reaction. On those grounds, an immunonanogold catalytic RS assay for IgG was designed. With addition of IgG, the amount of AuGIgG in the centrifuging solution decreased; the RS intensity at 796 nm (I _{796 nm}) decreased linearly. The decreased intensity ΔI _{796 nm} was linear with respect to the IgG concentration in the range of 0.08–16.0 ng · mL⁻¹ with a detection limit of 0.02 ng · mL⁻¹. This assay was applied to analysis of IgG in sera with satisfactory sensitivity, selectivity and rapidity. Supported by the National Natural Science Foundation of China (Grant No. 20667001), Natural Science Foundation of Guangxi Province (Grant No. 0728213), and the Foundation of New Century Ten-Hundred-Thousand Talents of Guangxi Province     

A novel method for detecting · OH radicals generated by photoexcited nanoparticles

The Fenton reactions occur because of the generation of H₂O₂ in the photoexcited independent TiO₂ systems or TiO₂/SnO₂ coupled systems. The ·OH radicals in these reactions were indirectly measured by colorimetric method. According to the Lambert–Beer law, we obtained the qualitative and quantitative relationships between the amount of TiO₂ or TiO₂/SnO₂ coupled particles and the amount of ·OH radicals produced by these systems. It provides a convenient procedure for making a thorough study on the photocatalytic mechanism of semiconductor nanoparticles, and in particular, to select highly efficient multicomponent semiconductor systems for photocatalysis.     

Silica veils-conductive diamond powder composite as a new propitious substrate for platinum electrocatalysts

An innovative composite was obtained by a straightforward sol-gel procedure, involving boron-doped diamond powder (BDDP) incorporation into a SiO₂ veil (SiO₂V) matrix. Composite-coated glassy carbon plates were used as substrate for Pt electrochemical deposition, and the electrodes thus obtained (Pt/BDDP–SiO₂V) were compared on a relative basis with those prepared in the absence of the silica matrix (Pt/BDDP). SEM measurements have shown that a BDDP substrate promotes Pt cluster formation, whereas on BDDP–SiO₂V, particles are much smaller (ca. 45 nm to ca. 140 nm). The activity for CH₃OH oxidation was checked by cyclic voltammetry, and it was found that at Pt/BDDP–SiO₂V, the main anodic peak is shifted with ca. 0.35 V toward lower potentials, indicating a considerable improvement in the overall process kinetics. Stripping experiments together with long-term polarization measurements demonstrated that when deposited on the BDDP–SiO₂V support, Pt particles are less susceptible to CO poisoning and this behavior was tentatively ascribed to the presence of a higher relative surface concentration of more stable, oxidized platinum species, as evidenced by XPS.     

Synthesis and properties of silica/polystyrene/polyaniline conductive composite particles

In this study, silica/polystyrene/polyaniline (SiO₂/PS/PANI) conductive composite particles were synthesized by four sequential reactions. The nanosized SiO₂ particles were synthesized from tetraethoxysilane (TEOS) by a sol–gel process with water as the solvent medium, followed by a surface modification with triethoxyvinylsilane; then the surface modified SiO₂ particles were used as seeds to synthesize SiO₂/PS composite particles with soapless seeded emulsion polymerization. Finally, the SiO₂/PS particles were used as seeds to synthesize the SiO₂/PS/PANI conductive composite particles. The sol–gel process of SiO₂, the effect of surface modification, and several other factors that influenced polymerization of styrene in the soapless seeded emulsion polymerization will be discussed. Either potassium persulfate (KPS) or 2,2′‐azobis(isobutyramidine) dihydrochloride (AIBA) was used as the initiator to synthesize the uniform SiO₂/PS particles successfully, and the cross‐section morphology of the SiO₂/PS particles was found to be of a core–shell structure, with SiO₂ as the core, and PS as the shell. The SiO₂/PS particles were well dispersed in many organic solvents. In the following step to synthesize SiO₂/PS/PANI conductive composite particles, sodium dodecyl sulfate (SDS) played an important role, specifically, to absorb aniline onto the surfaces of the SiO₂/PS particles to carry out the polymerization of aniline over the entire surface of the particles. The conductivity of the SiO₂/PS/PANI composite particles approached that of semiconductive materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 342–354, 2005     

Thermische Zersetzung von Afwillit Ca3(SiO3OH)2 · 2 H2O

Thermal Decomposition of Afwillite Ca₃(SiO₃OH)₂ · 2 H₂O Using the molybdate method [1], infrared, Raman, and high resolution solid state ¹H and ²⁹Si NMR spectroscopy two intermediate phases can be identified in the process of dehydration of afwillite: At temperatures of 250 to 300°C a non-crystalline phase is formed mainly (about 80 to 90% referred to Si) with a structure similar to mineral killalaite Ca₃OH(Si₂O₆OH) [2] and phase F [3]. Between 300 and 500°C this compound is converted to a non-crystalline kilchoanite-like phase γ-Ca₂SiO₄ · Ca₄Si₃O₁₀ [4], consisting of ordered γ-Ca₂SiO₄ and disordered trisilicate layers. By a side reaction polysilicate (about 10 to 20% referred to Si) is formed.