本体聚合中增长自由基的微环境效应

本文采用ESR技术和脉冲核磁梯度场自旋回波技术,论证了MMA、St本体聚合体系中增长自由基的反应活性和周围物理状态的微观非均一性,并讨论了这种非均一性对聚合反应的影响。     

The effect of monolithic zirconia thickness on the degree of conversion of dental resin cements: ATR-FTIR spectroscopic analysis

The purpose of this study was to evaluate the effect of monolithic zirconia thickness on degree of conversion (DC) of different resin cements. Five groups (1 mm, 1.5 mm, 2 mm monolithic zirconia, veneered zirconia substructure, and lithium disilicate) of disk-shaped ceramic specimens (14 mm in diameter) were prepared (n = 6). Three dental resin cements (Variolink II light-cured, Variolink II dual-cured and Zirconite dual-cured) were tested to evaluate their DC under each ceramic group. FTIR spectra were recorded using Attenuated Total Reflectance-Fourier Transform Infrared Spectrometer (ATR-FTIR). The DC% was calculated by ratio of infrared absorbance values of aliphatic and aromatic peaks for uncured and cured states. Data were statistically analyzed by Analysis of Variance (ANOVA) and post hoc Tukey tests (a = 0.05). DC of dental resin cement specimens under monolithic zirconia decreased with increasing thickness. For Variolink II light-cured cement, the highest DC found under lithium disilicate and the lowest DC observed under veneered zirconia specimens. Zirconite which is recommended for cementation of zirconia revealed the highest DC when polymerized under monolithic or veneered zirconia. Under lithium disilicate specimens, DC of Zirconite was similar with light-cured resin cement.     

本体聚合反应全过程苯乙烯增长自由基的ESR谱的研究

本文对苯乙烯本体聚合全过程增长自由基ESR谱进行了研究,对全过程ESR谱的模拟和分析及构象能的计算表明:反应初期12线谱由产生6线谱构象R_1和8线谱的构象R_2叠加而成,其相对含量R_1>R_2。反应中期4线谱和6线的ESR谱的模拟结果为:R_1相似文献   

Radical kinetics and characterization of the free radicals in gamma irradiated red pepper

Kinetic behaviors and characterization of the natural and γ-induced radicals in irradiated red pepper have been investigated by electron spin resonance (ESR) spectroscopy to explore the possibility of using this technique in detecting irradiated red pepper and to evaluate the eventual dosimetric features of this widely used food. Unirradiated samples exhibited a single resonance line centered at g=2.0050±0.0005. Photo-exposure of the samples was found to increase the signal intensity. An increase in temperature created a drastic decrease in the concentration of natural radicals responsible for the single resonance line. Irradiation was observed to induce increases in the intensity of single resonance line (signal I) and a radiation specific doublet and/or triplet (signal II) also centered at g=2.0050 but detectable only at high spectrometer gains. The intensities of both signals increased with increasing radiation dose. The signals I and II were found to decay with different rates depending on the temperature. The results of a fitting procedure applied to the experimental signal decay curves and those obtained from room temperature spectra simulation calculations were used together to determine radical species and their spectral characteristics giving rise to the observed experimental spectra. Four radical species, three carbohydrate and one semiquinone radical assigned as radicals A, B, C and D, respectively, were found to best explain the experimental results. All the radicals show large g and hyperfine splitting anisotropies varying between g=2.0028–2.0062 and 1.07–2.58 mT, respectively. The half lives of the radicals were found to depend strongly on temperature. The activation energy calculated using temperature dependent half-life data were the highest for radical A (33.68 kcal/mol) and smallest for radical C (11.83 kcal/mol).     

付氏反应中自由基的鉴定及其生成机理

本文通过一系列卤代烃与苯的付氏反应的ESR谱,研究了自由基物种的生成机理:它们起因于Lewis酸对由Scholl反应所生成的9,10-二取代蒽进行单电子氧化,并建立了一种生成9,10-二取代蒽自由基正离子的简单方法。首次报道了一个新自由基正离子1,2,3,4,5,6,7,8-八氘蒽的ESR谱。     

邻氨基苯甲酸/SiO2复合材料制备及其光热特性

有机发光体以其较高的发光效率、快速响应能力和较宽的可调谐波长被广泛应用于光转换材料、非线性光学材料和激光材料[1-3]。但是有机物的光学性能不稳定和热稳定性较差,使其在许多方面的应用受到限制。为了提高其光学和热稳定性,常用的方法是将各种有机发光体掺杂在以正硅酸乙酯为原料制得的SiO2凝胶玻璃基质中[4-6]。SiO2凝胶通常采用溶胶 凝胶法通过水解缩合制备。制备时一般采用无机酸作催化剂在酸性条件下进行,对质子酸作用敏感的有机物在酸性条件下往往热稳定性、光学性能下降,甚至遭到破坏。本文以廉价水玻璃为原料,在潜伏酸的…     

Formation of triphenylmethyl radicals in the thermolysis of polydiphenylenesulfophthalide and polytriphenylcarbinol

Triphenylmethyl radicals are formed in the thermolysis of polytriphenylcarbinol and polydiphenylenesulfophthalide, which give rise to ESR singlets with poorly resolved hyperfine structure and two bands in the electronic absorption spectra.Institute of Organic Chemistry, Urals Branch, Russian Academy of Sciences, 450054 Ufa. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 7, pp. 1682–1685, July, 1992.     

Formation of high-spin complexes in reactions of oxides of the γ-Al2O3 type with radical pairs of sterically shielded semiquinones: A new procedure for the preparation of organometallic polyradicals and their ESR spectra

A new simple method was developed for the preparation of organometallic bi- and triradicals by the heterogeneous reaction of γ-Al₂O₃ or analogous oxides with free radicals generated in solution through the interaction of 3,6-di-tert-butyl-o-benzoquinone with 3,6-di-tert-butylpyrocatechol. An explanation was offered for the plus sign of the dipoledipole coupling constant observed previously in the ESR spectra recorded in a superstrong field at low temperatures. Deceased. Translated fromIzvestiya Akademii Nauk, Seriya Khimicheskaya, No. 2, pp. 298–302, February, 1997.     

Improvement in energy conversion of electrostrictive composite materials by new approach via piezoelectric effect: Modeling and experiments

This study proposes a new model that couples the piezoelectric and electrostrictive behavior to minimize the polarization power of composite polymer. The development of this model is capable to predict the energy harvesting abilities of an electrostrictive composite. To improve the dielectric permittivity of electrostrictive polymer, the particles of PZT have been incorporated in order to increase the conversion efficiency of the composite. Dielectric characterization tests showed an increase in dielectric permittivity by a factor of 4.5 compared to pure polymer. Experimental measurements of harvested power validate the analytical model and demonstrate a good correlation between the two data. An equivalent of an electrical scheme has been developed, which allows modeling the two behaviors. The harvested power density under low frequency at 2% of strain can reach 0.30 μW/cm³ for 33% of PZT without the polarization field, including the conversion efficiency becomes higher. The energy harvester property of this material composite has excellent potential for several self‐powered applications such as wireless sensor networks and the internet of things.     

Calculations of Monomer Conversion and Radical Concentration in Reversible Addition‐Fragmentation Chain Transfer Radical Polymerization

Simple expressions are derived for the development of monomer conversion, as well as propagating radical, adduct radical, dormant chain, and dead chain concentrations in reverse addition‐fragmentation transfer polymerization (RAFT). The relations for the profiles of propagating radical concentration and conversion versus time are derived and depend on group parameters of rate constants and chemical recipe. The analytical equations are verified against numerical solutions of the mass‐balance differential equations. This derivation involves the steady‐state hypothesis for radical and RAFT agent concentrations. The errors introduced by these assumptions are negligible when the fragmentation rate constant, k_f, is higher than 10 s⁻¹ or when the cross‐termination rate constant, k_ct, is higher than 10⁵ L · mol⁻¹ s⁻¹.

Calculated concentration profiles (points: numerical, lines: analytical) of propagating radical R, adduct radical A, dormant T, and dead D (= P + P′) chains.     

The Construction of Stimulus-responsive Film Electrode by the Cu-catalyzed Radical Polymerization and its Application in Multi-valued Biologic Systems

N-isopropylacrylamide was polymerized on the surface of copper-plated carbon paper electrode by a novel redox initiation system composed of persulfate and copper nanoparticles, and the PNIPAAm−Cu NPs@CP film electrode was obtained. Cyclic voltammetry (CV) results showed that the electrode exhibits a reversible temperature, pH and glucose switchable electrical signal response through the ferrocene carboxylic acid (Fc(COOH)). With this basis, a 4-current output logic gate system consisting of 3-response inputs of temperature, pH, and glucose was fabricated and a corresponding logic circuit for 3-input/4-output ports was established. This work might provide a new avenue for the development of multi-valued biologic systems.     

Study on the electrochemical behavior and differential pulse voltammetric determination of rhein using a nanoparticle composite film-modified electrode

A sensitive electrochemical method was developed for the differential pulse voltammetric determination of rhein at a glassy carbon electrode (GCE) modified with a nanoparticle composite film. In the present paper, multi-wall carbon nanotube (MWNT) was dispersed into dihexadecyl phosphate (DHP) to give a homogeneous suspension. After the solvent evaporation, a uniform film of MWNT-DHP composite film was obtained on the GCE surface. The MWNT-DHP composite film-modified GCE exhibited excellent electrocatalytic behavior toward the redox of rhein. Compared with an irreversible reduction of rhein at the bare GCE, a reversible redox behavior of rhein was observed at the MWNT-DHP composite film-modified GCE and the redox current was also enhanced greatly. Based on this, a cathodic differential pulse voltammetry (DPV) was applied for the determination of rhein. The experimental parameters, which influence the current of rhein, were optimized. Under optimal conditions, the cathodic DPV measurements were performed and a linear response of rhein was obtained in the range from 1.0 x 10(-8) to 5.0 x 10(-6) mol L(-1) and with a limit of detect (LOD) of 5.0 x 10(-9) mol L(-1). The proposed procedure was successfully applied to assay rhein in real samples with satisfactory results.     

HZSM-5/SAPO-11负载Cr_2O_3催化转化LPG制低碳烯烃活性研究

SAPO-11晶化液中预置HZSM-5合成了HZSM-5(核)/SAPO-11(壳)复合分子筛。以复合分子筛为载体负载10%Cr_2O_3,研究了其孔分布、酸性质及其对液化石油气(LPG)转化制乙烯和丙烯反应的催化性能。结果表明,复合分子筛由HZSM-5表面包覆不同厚度的SAPO-11微晶组成,随着晶化时间延长,复合分子筛壳层厚度增加。复合分子筛负载Cr_2O_3催化剂的介孔率先增加后降低;弱酸量先增加后降低,强酸强度增加,强酸量先降低后增加,强酸密度减小。复合分子筛载体在LPG选择转化反应中催化性能优于单个分子筛和机械混合分子筛,其中,晶化12 h合成样品负载Cr_2O_3用于LPG转化反应对原料总转化率和乙烯+丙烯选择性最高,分别为42.63%和65.89%,CH_4和C_(5+)选择性分别为6.32%和15.48%。通过控制晶化时间可调变壳层厚度、复合分子筛介孔率以及酸性质,改善产物分布。     

Partial amination of cationic exchange resins and its application in the hydration of butene

In this work,the amination of sulfonated polystyrene resin with alkyl secondary amine is investigated.The catalytic activities of the modified resins are determined through the hydration of 1-butene.The optimum chain length and the best range of amination rate are determined.It is found that the single-pass conversion of 1-butene was raised 2% on average,and the relative activity was increased over 30% after modification.A hypothesis about the enhancement of catalytic activities by the inclusion of alkyl chain to wrap up the butene molecule is proposed.     

Dual functional AgNPs-M13 phage composite serves as antibacterial film and sensing probe for monitoring the corrosion of chromium-containing dental alloys

The preparation of silver nanoparticles(AgNPs)with microbe or plant tissues as bio-template offers green approach,while it suffers from low harvest and purification is needed.Herein,we propose a facile protocol for one-pot preparation of AgNPs using M13 phage as bio-template by simply mixing AgN03 solution with alkali M13 phage.In the obtained AgNPs-M13 phage composite,Cr(Ⅲ)selectively coordinates with the amino residues on phage surface and leads to the aggregation of AgNPs through the bridging of M13 phages.This makes it feasible for colorimetric sensing of Cr(Ⅲ)by measuring the absorbance ratio of AgNPs at 600 and 405 nm,which provides a LOD of 14 nmol/L.The composite also showed favorable bactericidal activity for both Gram-positive and Gram-negative bacteria,making it a promising candidate as antibacterial film in chromium-containing dental alloys and meanwhile serve as a sensing probe for monitoring the corrosion of the dental alloys.     

Reactive rubbers as toughening agents for thermoset polyester resins. Molecular analysis by FTIR and fracture behavior of the resulting blends

A reactive rubber obtained by isocyanation of hydroxyl-terminated polybutadiene was used as toughening agent for an unsaturated polyester resin. Both the isocyanation and the successive reaction between the modified rubber and the polyester were investigated by Fourier-transform infrared spectroscopy (FTIR). Fracture measurements at high and low strain rate were carried out on the cured materials to test their toughness. The failure mechanisms were established by morphological analysis of fractured surfaces, performed by scanning electron microscopy. © 1993 John Wiley & Sons, Inc.     

Kinetics and mechanism of the reaction of substituted benzyl bromides with copper in dimethylformamide

The reaction of copper metal with various substituted benzyl bromides in dimethylformamide has been studied and the kinetic and thermodynamic parameters of the reaction have been obtained. Hammett plots of log(k/k°) vs the substituent constant σ gave good correlations (ρ = 0.24, S_ρ = 0.03, r = 0.951). The structure of the organic group has little effect on the rate of reaction of substituted benzyl bromides with copper. In the absence of atmospheric oxygen, oxidative dissolution of copper occurred by the mechanism of single‐electron transfer with the formation of 1,2‐diphenylethanes and copper(I) complexes. The stereochemistry and intermediate compound were also studied and the reaction mechanism is discussed. Copyright © 2005 John Wiley & Sons, Ltd.     

Thermal stability and viscoelastic properties of MF/PVAc hybrid resins on the adhesion for engineered flooring in under heating system; ONDOL

The thermal properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The viscoelastic properties of the blends were also studied. Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The TGA results showed that the DTG_max temperature and thermal stability of the blends increased with increasing PVAc content. The blends were examined in non-isothermal DSC experiments at a heating rate of 10 °C/min. There was an exothermic peak in all the heating scanning curves, with each blend displaying a single curing peak temperature (T_p), intermediate between those of the two pure components and varying with the blend composition. The DMTA thermogram of MF resin showed that the storage modulus (E′) increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. E′ of MF resin increased both as a function of increasing temperature and with increasing heating rate.     

An ESR Approach to the Estimation of the Rate Constants of the Addition and Fragmentation Processes Involved in the RAFT Polymerization of Styrene

The reversible‐addition‐fragmentation chain transfer (RAFT) controlled radical polymerization of such vinylic monomers as styrene (= ethenylbenzene) has gained increasing popularity in current years. While there is a general agreement on the mechanism of RAFT polymerization, there is an ongoing debate about the values of the rate constants of its key steps, i.e., the addition of the propagating radicals to the mediator and the fragmentation of the resulting spin adducts. By carrying out an ESR spectroscopic investigation of the AIBN‐initiated polymerization of styrene (AIBN = 2,2′‐azobis[2‐methylpropanenitrile]), mediated by benzyl (diethoxyphosphoryl)dithioformate ( 5 ) as RAFT agent, we were able to detect and characterize four different radical species involved in the process. By reproducing their concentration–time profiles through a kinetic model, the addition and fragmentation rate constants at 90° of the propagating radicals to and from the mediator were estimated to be ca.10⁷ M ^?1 s^?1 and ca. 10³ s^?1, respectively. The validity of the kinetic model was supported by hybrid meta DFT calculations with the BB1K functional that predicted addition‐ and fragmentation‐rate‐constant values in good agreement with those estimated from the ESR experiments.     

富勒烯/环糊精复合物及其在生物医药领域的应用

富勒烯有着独特的球形结构,这一结构赋予了其优异的光电及生物性能,在生物医药领域备受关注。环糊精具有良好的水溶性和生物相容性,锥筒状结构赋予了其特异性包合作用,在主客体化学中有着非常重要的地位。富勒烯/环糊精的复合物,结合了富勒烯和环糊精的优势,在DNA切割,光动力学疗法,药物载体等领域发挥了重要作用。本文从富勒烯与环糊精体系的构筑出发,综述了富勒烯/环糊精非共价包合物及共价偶联物在生物医药领域应用的研究进展,且对富勒烯/环糊精复合物的应用进行了展望,为构建新型富勒烯/环糊精复合物提供参考。