2-(4-甲氧基苯基)-4,6-双(三氯甲基)-S-三嗪光引发剂的合成及其光聚合动力学性能研究

以对甲氧基苯甲腈和三氯乙腈为原料合成了光引发剂2-(4-甲氧基苯基)-4,6-双(三氯甲基)-S-三嗪(MBTT),通过傅里叶红外光谱仪、核磁共振仪和紫外吸收光谱对所合成的产物结构进行了表征.并利用实时红外(RT-IR)对该引发剂进行了光聚合反应动力学研究,考察了单体、引发剂浓度和光强对引发速率及单体转化率的影响.结果表明,MBTT是一种高效的紫外光引发剂,在引发剂用量为0.1%时光聚合的单体转化率就能达到90%;随着光强的增大,单体的双键转化率和最大反应速率都增大,诱导期缩短;双丙烯酸酯类单体的双键转化率比三丙烯酸酯类单体的双键转化率要高.     

Effect of cyclic acetals structure on efficiency of photoinitiation

Cyclic acetals were proposed as free radical polymerization photoinitiators or co‐initiators. The photopolymerization kinetics was recorded by real‐time infrared spectroscopy (RTIR). 2‐proply‐1,3‐benzodioxole (PBDO) and 2‐hexyl‐1,3‐benzodioxole (HBDO) were efficient photoinitiators for the polymerization of 1,6‐hexanedioldiacrylate (HDDA). Polymerization occurred at the highest rate with 1,3‐benzodioxolane (BDO) as a co‐initiator. When 1.82 wt % benzophenone (BP) was used as a photoinitiator, the addition of PBDO increased the rate of polymerization (R_p) and the final double bond conversion (DC_f) of HDDA, and an optimum cure rate (0.982 min^?1) was obtained at 1.64 wt % of PBDO. Combination of p‐chlorobenzophenone (CBP) and PBDO had the highest initiating reactivity. Cyclic acetals were inefficient co‐initiators for isopropylthioxanthone (ITX). Copyright © 2009 John Wiley & Sons, Ltd.     

Photoinitiated cationic polymerisation of multifunctional systems

Different types of tridimensional polymer networks have been synthetised by photoinitiated cationic polymerisation of vinyl ether and epoxy-functionalised oligomers and polymers. The polymerisation kinetics was followed by real-time infrared (RTIR) spectroscopy, a technique that records directly conversion versus time profiles in a timescale as short as 1 s. The addition of a diacrylate monomer was shown to accelerate the ring-opening polymerisation of epoxidized polyisoprene, with formation of interpenetrating polymer networks having well contrasted properties. A dual polymer network has been generated by photocrosslinking of a polyisoprene functionalised with both epoxy and acrylate groups.     

Photopolymerization of methyl methacrylate by use of a quinoline–bromine charge-transfer complex as the photoinitiator

Polymerization of MMA was carried out in presence of visible light (440 nm), quinoline-bromine charge-transfer complex being used as the photoinitiator. The initiator exponent was observed to be 0.5 up to 0.014 M initiator concentration; when chloroform was used as the solvent, the monomer exponent was found to be unity. The polymerization was inhibited in presence of hydroquinone but little inhibitory effect was observed in the presence of air. An average value of k²_p/k_t for this photopolymerization system was found to be (1.08 ± 0.22) × 10^-2. Kinetic and other evidence indicates that the overall polymerization takes place by a radical mechanism.     

Photopolymerization of methyl methacrylate and other vinyl monomers with the use of N-bromosuccinimide as photoinitiator

Polymerization of MMA was done in the presence of visible light (440 nm) with the use of N-bromosuccinimide (NBS) as the photoinitiator. The initiator exponent and intensity exponent were 0.5, and the monomer exponent was found to be unity. The polymerization was inhibited in the presence of hydroquinone. The average k_p²/k_t for this photopolymerization system was found to be 0.296 × 10^?2 and the activation energy of photopolymerization was 4.67 kcal/mole. Kinetic and other evidence indicate that the overall polymerization takes place by a radical mechanism. With NBS as the photoinitiator, the order of polymerizability at 40°C was MMA, EMA ? MA ? VA, and styrene could not be polymerized under similar conditions.     

Living ring-opening polymerization of cyclic thiocarbonate

This work deals with the cationic ring-opening polymerization of a cyclic thiocarbonate, 5,5-dimethyl-1,3-dioxane-2-thione (1). The polymerization was carried out with 2 mol% of trifluoromethanesulfonic acid, methyl trifluoromethanesulfonate, boron trifluoride etherate, or triethyloxonium tetrafluoroborate as an initiator to afford the polythiocarbonate with the narrow molecular weight distribution (M_n = 11200-31000, M_w/M_n = 1.04-1.15). The molecular weight of the obtained polymer could be controlled by the feed ratio of the monomer to the initiator and increased when the second monomer was added to the polymerization mixture after quantitative consumption of 1 in the first stage, supporting that the cationic ring-opening polymerization of 1 proceeded via a living process.     

Influence of temperature and nature of photoinitiator on the formation kinetics of an interpenetrating network photocured from an epoxide/methacrylate system

This paper deals with the synthesis of an interpenetrating network made of dimethacrylate and dicycloepoxide oligomers by photopolymerization. More particularly, the influence of several parameters (among which the photoinitiator nature and the reaction temperature) on the polymerization kinetics of each oligomer was studied. Two complementary analysis techniques were then used : the photocalorimetry and the RTIR spectroscopy. The study proceeded in several steps. Firstly, photopolymerization of each monomer was studied. Then, the same study was carried out on mixture of both monomers under conditions in such way than only one network is formed. It was shown that the second compound played the role of plasticizer on the network formed by the first monomer. Finally, the dimethacrylate/dicycloepoxide mixture was studied in the presence of both radical and cationic photoinitiators to synthesize an interpenetrating network (IPN). At 30 °C, ultimate products show a very incomplete epoxide conversion whereas the yield in methacrylic double bonds reaches 70%. On the other hand, epoxy functions react a little more than methacrylic double bonds at 90 °C. It was also shown that the presence of a radical photoinitiator is not necessary, and even slightly unfavourable, since the cationic photoinitiator is able to initiate both radical and cationic polymerization mechanisms.     

Photopolymerization of methyl methacrylate with the use of tetrahydrofuran–bromine charge-transfer complex as the photoinitiator

The polymerization of MMA was kinetically studied in the presence of visible light (using a 125-W high-pressure mercury vapor lamp with fluorescent coating, without a filter), a THF—bromine charge-transfer complex being used as the photoinitiator. The initiator exponent was 0.5 in bulk polymerization. The monomer exponent varied from about 1.2 to about 2.5, depending on the nature of the solvent used; the initiator exponent also varied in diluted systems, depending on the nature and proportion of the solvent, the variation being from a value of 0.5 in bulk system to zero or almost zero at about 25% (v/v) solvent concentration. Other kinetic parameters, viz., k_p²/k_t and the activation energy for polymerization, were determined and are reported. Kinetic and other evidence indicates that the photopolymerization takes place by a radical mechanism and termination is bimolecular in nature in bulk systems; in dilute systems, termination by initiator complex assumes predominance, particularly at high solvent concentrations (≥25% v/v).     

One‐component photoinitiator based on benzophenone and sesamol

A new benzodioxole derivative, 4‐(1,3‐benzodioxol‐5‐yloxy) benzophenone (BPBDO), based on benzophenone and sesamol was precisely synthesized, and it can be used as a 1‐component type II photoinitiator. Elementary analysis, atmospheric pressure chemical ionization mass spectrometry, ¹H nuclear magnetic resonance, and ¹³C nuclear magnetic resonance studies revealed that the molecular structure of BPBDO consisted of both benzophenone (BP) and benzodioxole (BDO) structures. The laser flash photolysis experiments and electron spin resonance test indicated that the process of radicals generated from BPBDO after irradiation was similar to 3 processes of ethyl 4‐dimethylaminobenzoate and BP. The kinetics of photopolymerization of the photoinitiator was also studied by real‐time infrared spectroscopy. The oxygen content, light intensity, and viscosity of the monomer affected the decomposition (R_d) and polymerization rate, and the final double bond conversion was also studied. All the results suggest that BPBDO is a 1‐component photoinitiator that is an efficient photoinitiator for free radical polymerization. In contrast to typical dual‐component photoinitiators, eg, BP/ethyl 4‐dimethylaminobenzoate or BP/BDO, BPBDO does not require an additional amine coinitiator for the initiation and is applicable in nonamine resin systems.     

Novel panchromatic photopolymerizable matrices: N,N'‐dibutylquinacridone as an efficient and versatile photoinitiator

N,N'‐dibutylquinacridone (DBQA) is utilized here for the first time as a high‐performance panchromatic photoinitiator for the cationic polymerization (CP) of epoxides, the free radical polymerization (FRP) of acrylates, the thiol‐ene polymerization and the synthesis of interpenetrated polymer networks (epoxide/acrylate) under violet, blue, green and yellow lights (emitted from LED at 405 nm, 470 nm, 520 nm, or 594 nm, or laser diode at 532 nm). It confers a panchromatic character to the photopolymerizable matrices. Remarkably, the proposed DBQA based photoinitiating systems exhibit quite excellent efficiency (the final monomer conversion for multifunctional monomers at room temperature can reach 62% and 50% in CP and FRP, respectively) and appear as much more powerful than the camphorquinone or Eosin‐Y containing reference systems for visible light. For green light, DBQA is much more reactive than the literature reference (Eosin‐Y) and for blue light, a good reactivity is found compared with camphorquinone. The photochemical mechanisms are studied by molecular orbital calculations, steady state photolysis, fluorescence, cyclic voltammetry, laser flash photolysis, and electron spin resonance spin trapping techniques. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1719–1727     

A thioxanthone‐based visible photoinitiator

Thioxanthone‐based 9‐(2‐Morpholine‐4yl‐acetyl)‐5‐thia‐napthasen‐12‐one (TX‐MPM) was synthesized and characterized as a one‐component novel visible photoinitiator. Its capability to act as an initiator for the polymerization of methyl methacrylate (MMA) was examined in photoreactor and also daylight. Photophysical properties: fluorescence and phosphorescence emission spectra and fluorescence quantum yield of TX‐MPM (?_f = 0.29) were determined. The phosphorescence lifetime was found 131 ms for TX‐MPM and 110 ms for initiator‐attached polymer (PMMA) at 77 K, indicated a π→π* nature of the lowest triplet state. A model compound, morpholino acetonapthone was used as quencher for the triplet states of TX‐MPM and the quenching rate constant was determined (k_q = 1.26 × 10⁹ M^?1s^?1). According to laser flash photolysis studies, intermolecular hydrogen abstraction process was more dominant path to the formation of the initiating radicals. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Photoinitiated,inverse emulsion polymerization of acrylamide: Some mechanistic and kinetic aspects

The kinetics of photoinitiated, inverse emulsion polymerization of acrylamide with 2,2‐dimethoxy‐2‐phenylacetophenone (DMPA) as a photoinitiator was investigated under three different cases. First, in a quartz reactor transparent to full UV light, the polymerization rate (R_p) increased and then decreased with the change of initiator order from 0.27 to a negative value when the DMPA concentration was increased, and it was particularly unusual that monomer orders at different DMPA concentrations were lower than the first. Second, for polymerization without DMPA in a quartz reactor, the dependence of R_p on monomer concentration was similar to that of R_p on initiator concentration in the aforementioned case. Third, when polymerization was carried out in a Pyrex reactor where the far UV light was filtered, a peak rate was also observed, and initiator orders varied from 0.24 to a negative value; however, under this case monomer orders at different initiator concentrations were greater than the first. These results indicated that the effect of absorbance often observed in bulk or solution photopolymerization also existed in this system, and the self‐initiation of monomer had some influence on polymerization, and the role of primary radical termination could not be neglected, as evidenced by kinetic analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 846–852, 2004     

2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑复合光引发体系的光聚合动力学研究

本文研究了对2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑(BMOIM)复合光引发体系引发聚合动力学过程.采用紫外光谱仪对引发剂、供氢体、增感剂在紫外区的吸收谱图进行了表征.利用实时红外光谱仪对复合光引发体系引发聚合动力学过程进行实时监测,考察了不同光强、引发剂浓度以及不同官能度单体对反应速率及最终双键转化率的影响.结果表明,在引发剂浓度为0.6%(质量分数)时,20s内双键转换率达到96%,随着引发剂浓度的提高,聚合速率增大.聚合速率以及最终双键转化率随着光强增大而增大;双官能团单体的最终双键转化率比三官能团单体的最终双键转化率要高.     

A simplified data treatment for dead-end and high conversion polymerization kinetics

A simplified approximation method for the treatment of dead-end and high conversion polymerization kinetics is presented. The method is based on the treatment of dead-end polymerization first described by Tobolsky. In appropriate circumstances, by contrast with Tobolsky's method, this method provides measurements of k_d and k_p/k_t^1/2 without recourse to the measurement of the monomer conversion at infinite time. Kinetic studies of free radical polymerizations are normally confined to measurements of initial rates. At low conversions the predictions of the general mechanism for chain-growth polymerization involving initiation, propagation, and termination steps are generally obeyed. Thus the polymerization rate should be first order in the vinyl monomer and half-order in the initiator concentrations. At high conversions, however, large deviations which can be ascribed to various effects can occur; for example, (1) the effect of the increasing viscosity of the polymerization medium on the termination rate constant k_t, and possibly also on the propagation rate constant k_p, which have been considered by North¹ and Cardenas and O'Driscoll,² or (2) depletion of the initiator as the polymerization progresses. This depletion will occur in all polymerizations but its significance will depend on the magnitude of the rate constant for initiator decomposition (k_d) and the period of polymerization. Appropriate conditions will lead to limiting monomer conversion even after infinite polymerization time; this phenomenon has been called dead-end polymerization by Tobolsky.³ Free radical polymerizations to high conversion are particularly important in the industrial context when initial kinetics are obviously inadequate. Suitable treatment of the conversion/time relationship is highly desirable. Senogles and Woolf⁴ have examined the polymerization of n-lauryl methacrylate at 60°C with 2-azobisisobutyronitrile as initiator under dead-end conditions. Here we propose a modification of Tobolsky's treatment of such polymerizations by using an approximation for the exponential decay in the initiator concentration. This method permits easy manipulation of the experimental data and the estimation of values for the kinetic parameters in favorable circumstances without recourse to the measurement of the conversion at infinite time or the evaluation of complicated functions of the monomer conversion. The method thus allows the duration of the laboratory experimentation to be significantly shortened and the complexity of the subsequent data analysis to be considerably reduced.     

Kinetic model of living radical polymerization

This work studies the kinetics of living radical polymerization by means of both the nonsteady state approach and the quasi-stationary state method. Expressions for the numberand weight-average degress of polymerization and the polydispersity index were derived. Numerical results show that the concentration of residual initiator seriously influences the polydispersity index of the resulting polymer. The calculated outcomes of the non-steady state approach are evidently different from those of the quasi-stationary state method when the magnitude of the rate constant of termination is comparable with that of the propagation rate constant, and the difference becomes negligible if the rate constant of the termination (k_t) is much larger than that of propagation (k_p). The polydispersity index of the resulting polymer increases with decreasing ratios of k_t to k_p or M_O to I_O (initial concentrations of monomer and initiator).     

A Study on the Optically Active Polymer Poly‐β‐pinene

Poly‐β‐pinene (PBP) was obtained by radiation‐induced polymerization of monomer with γ radiation. The polymerizations were conducted both in vacuum and in the presence of air at different radiation doses up to 1–3 MGy. It was found that the presence of oxygen retards the polymerization rate and reduces the polymer yields and the radiation chemical yield suggesting that the polymerization mechanism involves free radicals. It is shown that PBP can also be obtained in low yields from β‐(‐)pinene polymerization with a free radical initiator. The chemical structures of the PBP radiopolymer and PBP obtained by a free radical initiator were studied by FT‐IR and ¹³C CP‐MAS NMR spectroscopy. The data shows that the PBP obtained have highly ordered structures, which is manifested also by the very high specific optical rotation which is about 3 times that of the starting monomer in the case of the radiopolymer and about 5 times in the case of the PBP prepared with the free radical initiator. In contrast, PBP obtained in high yields by cationic polymerization shows a very low specific optical rotation, much lower than that of the starting monomer and low regularity in chemical structure has been attributed to this polymer by FT‐IR and ¹³C CP‐MAS NMR spectroscopy. It is shown that PBP with high optical activity racemizes over an acidic catalyst.     

Kinetic study of the cationic photopolymerization of epoxy monomers

The photoinitiated cationic polymerization of di-epoxy monomers has been studied using real-time infrared (RTIR) spectroscopy. The polymerization rate and the amount of unreacted monomer were determined directly from the conversion vs. time curves recorded. The cure speed was greatly increased by using a Kr⁺ laser (337.4 nm) as radiation source. A 0.25 s exposure proved sufficient to make react more than 60% of the epoxy groups. The overall polymerization quantum yield was evaluated to be 200 mol photon^-1. Dark polymerization was shown to develop extensively after the UV exposure for about 30 min and may represent up to 80% of the total process. The hardening of the UV-cured tack-free coating was found to occur mainly in the dark, leading after 1 h to a very hard and glassy material. A bimolecular chain termination process is postulated to account for the decay profile of the reactive species observed after UV exposure.     

4-N,N-Dimethylamino-4'-Isopropylbenzophenone as polymerization photoinitiator. Effect of solvent and photoinitiator concentration on its photoreactivity and on the polymerization process

Several kinetics aspects of the methyl methacrylate (MMA) polymerization using 4-dimethylamino-4'-isopropylbenzophenone (PI) as photoinitiator have been studied. The order of the polymerization reaction with respect to monomer and initiator concentrations have been investigated, as well as the polymerization behavior under well-stirred and unstirred conditions; values of initiation quantum yield (?_i) and k_p/k_t^1/2 have also been determined. It has been found that the nature of the polymerization-initiating radicals depends on the type of solvent and the photoinitiator concentration ([PI]). In cyclohexane solution and at low [PI] (< 5 x 10^-5M), the cyclohexyl radical is practically the only polymerization initiating radical, while at higher [PI] both radicals, cyclohexyl and the aminoalkyl derived from PI, participate in the initiation step, increasing the participation of the later as the [PI] increases. When benzene is used as solvent both phenyl and aminoalkyl radicals participate in the initiation step at any [PI] employed. Efficiencies of the radicals derived from solvent and photoinitiator have been determined.     

Indefinitely active aqueous cationic polymerizations,part I: Low cost,recyclable initiator systems

This article describes the first example of an aqueous cationic polymerization that utilizes a low cost, safe, and highly recyclable initiator system (phosphotungstic acid) that retains its activity indefinitely. Quantitative yields of low to medium molecular weight polymers of p-methoxystyrene and N-vinylcarbazole are obtained within minutes to hours. Polymerization is first order in both monomer and phosphotungstic acid. Negatively charged surfactants suppress polymerization; whereas, nonionic soaps increase the reaction rate and reduce both polymer molecular weight and polydispersity index. Herein, the discovery of a new form of aqueous cationic polymerization involving the condensation of the alcoholic derivative of p-methoxystyrene, 1-(4-methoxyphenyl)ethanol, is also disclosed.     

Initiator effect on the cationic ring‐opening copolymerization of 2‐ethyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline

The aim of this research was to study the effect of the initiator on the resulting monomer distribution for the cationic ring‐opening copolymerization of 2‐ethyl‐2‐oxazoline (EtOx) and 2‐phenyl‐2‐oxazoline (PhOx). At first, kinetic studies were performed for the homopolymerizations of both monomers at 160 °C under microwave irradiation using four initiators. These initiators have the same benzyl‐initiating group but different leaving groups, Cl^?, Br^?, I^?, and OTs^?. The basicity of the leaving group affects the ratio of covalent and cationic propagating species and, thus, the polymerization rate. The observed differences in polymerization rates could be correlated to the concentration of cationic species in the polymerization mixture as determined by ¹H NMR spectroscopy. In a next‐step, polymerization kinetics were determined for the copolymerizations of EtOx and PhOx with these four initiators. The reactivity ratios for these copolymerizations were calculated from the polymerization rates obtained for the copolymerizations. This approach allows more accurate determination of the copolymerization parameters compared to conventional methods using the composition of single polymers. When benzyl chloride (BCl) was used as an initiator, no copolymers could be obtained because its reactivity is too low for the polymerization of PhOx. With decreasing basicity of the used counterions (Br^? > I^? > OTs^?), the reactivity ratios gradually changed from r_EtOx = 10.1 and r_PhOx = 0.30 to r_EtOx = 7.9 and r_PhOx = 0.18. However, the large difference in reactivity ratios will lead to the formation of quasi‐diblock copolymers in all cases. In conclusion, the used initiator does influence the monomer distribution in the copolymers, but for the investigated system the differences were so small that no difference in the resulting polymer properties is expected. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4804–4816, 2008