On-line high-performance liquid chromatography-solvent evaporation - high-performance liquid chromatography - capillary gas chromatography - flame ionisation detection for the analysis of mineral oil polyaromatic hydrocarbons in fatty foods

An automated on-line method is described that involves a first LC separation on a large column, evaporation of a 6-ml fraction in an on-line solvent evaporator, a second LC separation using a different mobile phase, fractionating the components of interest and transfer to GC through the in-line vaporiser/overflow interface. The method is designed for the injection of a large amount of food extract (e.g. up to 200 mg of fat) and is applied to the analysis of mineral oil material in a linseed oil.     

Determination of organochlorine compounds in fatty matrices: Application of normal-phase LC clean-up coupled on-line to GC/ECD

Off-line normal-phase LC has been used for the clean-up of compounds in our laboratory for several years. On-line coupling of this LC system, which typically yields 12 ml fractions, is not possible due to its large fraction volume. The maximum transfer volume in on-line LC-GC/ECD is approx. 300 μl. Therefore down-scaling of the LC system was attempted in order to reach these low fraction volumes. Miniaturization resulted in a 240 μ1 LC fraction containing the analytes of interest, which is transferred to GC/ECD via an on-column interface. Sensitivity requires that a minimum amount equivalent to 1–2 mg of sample should reach the GC detector; the selectivity is determined by the separation between the matrix and the last eluting target analyte. For the analysis of fatty samples, limitations were observed in the separation of dieldrin from triglycerides. Other organochlorine compounds, e.g. polychlorobiphenyls (PCBs), the DDT group, HCB and the HCHs can be analyzed with RSDs of 2–4 % (n = 10) at concentration levels of sub-μ/kg in milk fat using a 3 μm Hypersil silica 50 × 1.0 mm i.d. LC column.     

Liquid chromatography/tandem mass spectrometry of unusual phenols from Yucca schidigera bark: comparison with other analytical techniques

Qualitative and quantitative analyses of phenolic compounds are of interest for both medicinal and food plants. In the present work, the phenolic fraction from Yucca schidigera, a plant bearing the GRAS (Generally Recognized as Safe) label approved by the US Food and Drug Administration, was studied. Crude extracts of Y. schidigera bark were investigated by liquid chromatography/UV spectrophotometry with diode-array detection, liquid chromatography/electrospray ionization mass spectrometry (LC/ESI-MS) and liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS), in order to develop and optimize simple and rapid techniques to determine both stilbenes and yuccaols for the purposes of quality control of collected material. With optimal LC and MS conditions, stilbenes and yuccaols were quantified with all the proposed methods and the results were compared. Sensitivity was evaluated and the results indicated that MS/MS detection in the multiple reaction monitoring mode is easily applicable to this plant and allows the rapid and direct identification and quantification of these peculiar compounds in crude plant extracts.     

Determination of p,p′-DDE and PCBs in adipose tissues using high-performance liquid chromatography coupled on-line to capillary GC – the EURAMIC study

Long-term exposure to fat-soluble xenobiotics is assessed by the concentration of DDE [1,1-dichloro-2,2-bis(p-chlorophenyl)ethyl-ene], the persistent metabolite of DDT, in subcutaneous fat, aspirated from the buttocks of breast cancer patients and age-matched controls, from five European centers collaborating in a case-control study on breast cancer. In such studies using sample material of living subjects only small amounts of samples can be made available for analysis. In this particular study the only sample material available for the analysis of DDE were aliquots of the aspirates that were originally analyzed for fatty acids. Due to the small sample quantities available, e.g. aliquots of 200–800 p. 1, on-line LC-GC is most convenient because a major part of the sample can be used in the analytical procedure. In the LC-GC procedure 50 μl of sample was injected on the LC column resulting in a 180 μl fraction containing the analytes of interest. The LC fraction was transferred to a capillary GC with electron capture detector by means of partially concurrent solvent evaporation. This way, sample handling is minimized thus reducing losses and preventing contamination. The feasibility of the on-line LC-GC system for the analysis of DDE is demonstrated with the analysis of 634 adipose tissue extracts in different series. The validity of this approach, using samples already analyzed for another parameter, with LC-GC is clearly demonstrated by the fact that in over 97% of the samples DDE can be quantified. Thus rendering a meaningful data-set for further epidemiological evaluation. The DDE levels found ranged from 0.99–3.13 μg/g adipose tissue.     

Phase equilibria in solutions of cellulose derivatives and the rheological properties of solutions in various phase states

Phase equilibria in solutions of hydroxypropyl cellulose in such solvents as water, propylene glycol, poly(ethylene glycols) of various molecular masses, triethyl citrate, and DMSO are analyzed. The phasetransition lines are constructed with the use of microinterference and polarization microscopy methods. In a certain temperature-concentration range, all solutions undergo a sequence of transitions typical for solutions of stiff-chain crystallizable polymers: isotropic and LC states separated by the two-phase corridor and, in some cases, the crystalline state. Of special interest are systems in which the superposition of amorphous (with the LCST or UCST), LC, and crystalline equilibria is realized. The features of the phase states of solutions are compared with the physicochemical characteristics of solvents and the intensity of their interaction with hydroxypropyl cellulose macromolecules. Solutions occurring in various phase states are tested by rheological methods. These solutions demonstrate the typical rheological behavior of anisotropic solutions: the presence of yield stress and the extremum concentration dependence of viscosity with a maximum, when the LC phase appears, and a minimum, when it transforms into the 100% phase. In the case of single-phase solutions, viscosity increases with concentration, while for two-phase solutions, viscosity decreases with an increase in the fraction of the LC phase. The rheological data are found to be sensitive to phase transitions observed in solutions.     

Effects of the gradient profile, sample volume and solvent on the separation in very fast gradients, with special attention to the second-dimension gradient in comprehensive two-dimensional liquid chromatography

Gradient elution provides significant improvement in peak capacity with respect to isocratic conditions and therefore should be used in comprehensive two-dimensional LC×LC, both in the first and in the second dimension, where, however, gradients are limited to a short time period available for separation, usually 1 min or less. Gradient conditions spanning over a broad mobile phase composition range in each second-dimension fraction analysis are used with generic "full in fraction" (FIF) gradients. "Segment in fraction" (SIF) gradients cover a limited gradient range adjusted independently to suit changing lipophilicity range of compounds transferred to the second dimension during the first-dimension gradient run and to provide regular coverage of the two-dimensional retention space. Optimization of the gradient profiles is important tool for achieving high two-dimensional peak capacity and savings of the separation time in comprehensive LC×LC. Calculations based on the well-established gradient-elution theory can be used to predict the elution times and bandwidths in fast gradients, taking into account increased probability of pre-gradient or post-gradient elution. The fraction volumes transferred into the second dimension may significantly affect the second-dimension bandwidths, especially at high elution strength of the fraction solvent, which may cause even band distortion or splitting in combined normal-phase (HILIC)-RP systems, but also in some two-dimensional RP-RP systems. In the present work, the effects of the fast gradient profile, of the sample volume and solvent on the elution time and bandwidths were investigated on a short column packed with fused-core porous-shell particles, providing narrow bandwidths and fast separations at moderate operating pressure.     

Broadband reflective cholesteric liquid crystalline gels: volume distribution of reflection properties and polymer network in relation with the geometry of the cell photopolymerization

The ultraviolet (UV) light‐absorbing properties of the liquid crystal (LC) constituent during the photo‐induced elaboration of a cholesteric LC (CLC) gel may induce the broadening of the reflection bandwidth of the material, a situation that is promoted by asymmetrical irradiation conditions (only one side of the cell is irradiated). The in situ structure of the polymer network, included in the LC, was investigated by transmission electron microscopy and the temperature dependence of the reflection properties examined; it is shown that the network has a structure gradient that is at the origin of the broadening phenomenon. The smallest reflection wavelength is related to the cell side from which the UV light beam came in. A priori, this situation was unexpected since it is shown that this part of the gel is enriched with nematic (infinite‐pitch CLC) network‐forming material. The result is discussed in relation to the variation of the reflection band characteristics with polymer concentration, which offers the opportunity for indirect access to the volume distribution of the cholesteric periodicities. For applications, broadband reflective cholesteric gels may be of interest for reflective polarizer‐free displays or for the light management with smart electrically‐switchable reflective windows.     

Broadband reflective cholesteric liquid crystalline gels: volume distribution of reflection properties and polymer network in relation with the geometry of the cell photopolymerization

The ultraviolet (UV) light-absorbing properties of the liquid crystal (LC) constituent during the photo-induced elaboration of a cholesteric LC (CLC) gel may induce the broadening of the reflection bandwidth of the material, a situation that is promoted by asymmetrical irradiation conditions (only one side of the cell is irradiated). The in situ structure of the polymer network, included in the LC, was investigated by transmission electron microscopy and the temperature dependence of the reflection properties examined; it is shown that the network has a structure gradient that is at the origin of the broadening phenomenon. The smallest reflection wavelength is related to the cell side from which the UV light beam came in. A priori, this situation was unexpected since it is shown that this part of the gel is enriched with nematic (infinite-pitch CLC) network-forming material. The result is discussed in relation to the variation of the reflection band characteristics with polymer concentration, which offers the opportunity for indirect access to the volume distribution of the cholesteric periodicities. For applications, broadband reflective cholesteric gels may be of interest for reflective polarizer-free displays or for the light management with smart electrically-switchable reflective windows.     

Polyamide-11/lead zirconate titanates—a novel composite material with high dielectric properties

Polymeric composites gain increasing interest in materials research and practice applications due to combining excellent electric property of piezoelectric ceramic and flexibility of polymer matrix. A novel decoupling capacitor with high dielectric constant has been developed by mixing polyamide-11 (PA11) with ferroelectric ceramic lead zirconate titanates (PZT). The composite demonstrates high dielectric constant, with better frequency stability and low dielectric losses. The dependence of the dielectric constant on frequency and polymer fraction was investigated. The excellent dielectric constant of 100 and the dielectric loss of 0.1 can be obtained at a PA11 volume fraction of 0.4. The enhanced dielectric behavior originates from good connection between ferroelectric ceramic and PA11 Dielectric losses of the PZT/PA11 composites change slightly with the test frequency. Our findings suggest that the created polymeric composites with relatively high dielectric constant represent a novel type of material that is flexible and easy to process. Moreover, is suited to applications in advanced decoupling capacitors and flexible electronics.     

Certified calibration solution reference material for the determination of perfluorooctane sulfonate from the National Metrology Institute of Japan (NMIJ)

A new calibration solution reference material for the determination of perfluorooctane sulfonate anion (PFOS) and its salts has been issued as a certified reference material (CRM) by the National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The purity amount-of-substance fraction of raw material potassium perfluorooctane sulfonate (K-PFOS) was evaluated based on the results obtained using the freezing point depression method, and the purity mass fraction of the raw material was calculated using the average molar mass of impurities, the molar mass of K-PFOS, and the purity amount-of-substance fraction. The certified concentration of this CRM was obtained by multiplying the dilution ratio of the raw material in a prepared solution (methanol) determined from the gravimetric blending method by the purity of the raw material. The preparation concentration of K-PFOS as a certified value of NMIJ CRM 4220-a was determined to be 9.93?mg?kg^?1. In addition, the standard uncertainty of the certified value was evaluated from the purity evaluation as well as from sample inhomogeneity, instability, and preparation variation obtained from LC/MS measurements of different gravimetrically prepared solutions of the NMIJ CRM. Consequently, the expanded uncertainty was estimated to be 0.15?mg?kg^?1 with a coverage factor k?=?2 corresponding to the half-width of estimated confidence interval of approximately 95%.     

2D 129Xe EXSY of xenon atoms in a thermotropic liquid crystal confined to a controlled-pore glass

Two-dimensional (129)Xe exchange spectroscopy (EXSY) NMR measurements are presented for xenon atoms dissolved in a thermotropic nematic Liquid Crystal (LC), Merck Phase 4, confined to a mesoporous Controlled-Pore Glass (CPG) material with an average pore diameter of 81 A. Experiments were carried out as a function of mixing time at two different temperatures in which Phase 4 appears in nematic and isotropic phases. The exchange rate constants of xenon atoms between two different sites were determined utilizing the intensities of diagonal and off-diagonal signals measured in the EXSY spectra. In the studied system, the sites are: (a) xenon dissolved in the bulk LC between the CPG particles; and (b) xenon in the LC confined inside the pores. The diffusion rate of xenon atoms between the various sites was observed to be very slow.     

LC-GC analysis of the aromatics in a mineral oil fraction: Batching oil for jute bags

Aromatics of a C₁₅? C₃₀ mineral oil fraction, the “batching oil” used for producing jute fabrics, were analyzed for estimating the toxicity of oil transferred from jute bags to foods. Group-type pre-separation according to ring systems occurred on a LC NH₂ column with pentane and small additions of methanol as eluent. LC fractions were characterized by LC-GC-MS and quantitated by LC-GC-FID. The oil contained 23% aromatics and 1% “polars”; some 99.5% of the aromatics were alkylated.     

Development and Application of Liquid Crystals as Stimuli-Responsive Sensors

This focused review presents various approaches or formats in which liquid crystals (LCs) have been used as stimuli-responsive sensors. In these sensors, the LC molecules adopt some well-defined arrangement based on the sensor composition and the chemistry of the system. The sensor usually consists of a molecule or functionality in the system that engages in some form of specific interaction with the analyte of interest. The presence of analyte brings about the specific interaction, which then triggers an orientational transition of the LC molecules, which is optically discernible via a polarized optical image that shows up as dark or bright, depending on the orientation of the LC molecules in the system (usually a homeotropic or planar arrangement). The various applications of LCs as biosensors for glucose, protein and peptide detection, biomarkers, drug molecules and metabolites are extensively reviewed. The review also presents applications of LC-based sensors in the detection of heavy metals, anionic species, gases, volatile organic compounds (VOCs), toxic substances and in pH monitoring. Additionally discussed are the various ways in which LCs have been used in the field of material science. Specific attention has been given to the sensing mechanism of each sensor and it is important to note that in all cases, LC-based sensing involves some form of orientational transition of the LC molecules in the presence of a given analyte. Finally, the review concludes by giving future perspectives on LC-based sensors.     

Size control of phase‐separated liquid crystal droplets in a polymer matrix based on the phase diagram

When a mixture of liquid crystal (LC) and photo reactive monomer is irradiated by UV light, polymerization occurs and LC droplets form through phase separation, producing polymer dispersed LCs (PDLCs). Although size control of LC droplets and reduced amounts of LC in PDLC films are important in applications, precise size control of LC droplets at a low LC fraction has not yet been accomplished. In this study, the phase diagrams of the LC/initial monomer and the LC/polymer during polymerization were used to control LC droplet size at various LC fractions. Both the relative position of the sample in the initial phase diagram and the shift of the phase separation line during polymerization were shown to be important in determining the size of LC droplets. Our results are expected to provide a new strategy for precise size control of LC droplets especially at a low LC fraction range, which would be a great help for PDLC applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Rapid analysis of antibiotic-containing mixtures from fermentation broths by using liquid chromatography-electrospray ionization-mass spectrometry and matrix-assisted laser desorption ionization-time-of-flight-mass spectrometry

A crucial step in the isolation of antibiotic substances is establishing whether or not the isolated material represents a new chemical entity. Because of the importance of molecular weight to this process--known as dereplication--mass spectrometry has traditionally played an active role. In this communication a strategy for utilizing liquid chromatography-mass spectrometry (LC/MS) for novelty assessment is described. Crude extracts (20-50 μg) are chromatographed by conventional bore high-performance liquid chromatography (1 mL/min) after which a postcolumn split to divert roughly one-tenth of the sample to the mass spectrometer for molecular weight determination by electrospray ionization (ESI) mass spectrometry. The majority of the effluent is sent to a UV detector and ultimately collected as 1-min fractions for biological testing. As a secondary confirmation of molecular weight, an aliquot of each fraction (< 5%) is taken for analysis by matrix-assisted laser desorption ionization (MALDI). The improved efficiency of this approach over more traditional schemes utilizing off-line fraction collection and conventional ionization methods can be explained by several factors. First, the superior sensitivity of ESI and MALDI means that less material is required for successful analysis. Second, on-line LC/MS optimizes the efficiency of sample transfer and saves both time and labor. Furthermore, the concentration dependence of ESI allows a majority of the material injected for LC/MS to be recovered for biological testing without compromising the signal available for molecular weight determination. As a validation of the above method, crude extracts containing two well-characterized antibiotics--teicoplanin and phenelfamycin--were examined. Results from these analyses are presented along with data from the analysis of a potent unknown antifungal sample.     

Preparation of liquid crystalline polymers with monosubstituted ferrocenyl pendant groups and generation of unpaired electrons by complexation with tetracyanoethylene in the solid state

Liquid crystalline (LC) polymers with monosubstituted ferrocenyl units in the side chain were prepared by radical polymerizations of the corresponding LC and non-LC acrylates. It was demonstrated that polymerization is useful for the LC orientation and expands the LC temperature range. In addition, these mesogenic ferrocenes form a complex with tetracyanoethylene (TCNE) to give spin labeled molecules simply by mixing the ferrocenyl compounds with TCNE in the solid state at ambient temperature.     

Effects of the fluorinated liquid crystal molecules on the electro-optical properties of polymer dispersed liquid crystal films

The different fluorinated liquid crystal (LC) molecules doped to E8 were used as LC component to prepare polymer dispersed liquid crystal (PDLC) films. The mass fraction of the LC mixture is fixed 50.0 wt%. Results indicate that doping 8.0 wt% fluorinated LC molecule ME3CP to E8 significantly reduced the driving voltage of the PDLC films, and the driving voltage reduced with the rise of mass fraction of ME3CP. Besides, the terminal flexible chain length of the fluorinated LC molecule influenced the LC mixture properties based on E8, such as the dielectric anisotropy, birefringence and viscosity of the LC mixture, and the morphology and the electro-optical properties of PDLC films were controlled not only by the physical properties of the LC mixture, but also by the terminal flexible chain length of the fluorinated LC molecule .     

The combination of liquid chromatography/tandem mass spectrometry and chip-based infusion for improved screening and characterization of drug metabolites

An approach has been developed for drug metabolism studies of non-radiolabeled compounds using on-line liquid chromatography/tandem mass spectrometry (LC/MS/MS) combined with chip-based infusion following fraction collection. The potential of this approach, which improves the data quality compared with only LC/MS analysis, has been investigated for the analysis of in vitro metabolites of tolcapone and talinolol, two compounds with well-characterized metabolism. The information-dependent LC/MS/MS analysis enables the characterization of the major metabolites while the chip-based infusion is used to obtain good product ion spectra for lower level metabolites, to generate complementary MS information on potential metabolites detected in the LC/MS trace, or to screen for unexpected metabolites. Fractions from the chromatographic analysis are collected in 20 second steps, into a 96-well plate. The fractions of interest can be re-analyzed with chip-based infusion on a variety of mass spectrometers including triple quadrupole linear ion trap (QqLIT or Q TRAP) and QqTOF systems. Acquiring data for several minutes using multi-channel acquisition (MCA), or signal averaging while infusing the fractions at approximately 200 nL/min, permits about a 50 times gain in sensitivity (signal-to-noise) in MS/MS mode. A 5-10 microL sample fraction can be infused for more than 30 min allowing the time to perform various MS experiments such as MS(n), precursor ion or neutral loss scans and accurate mass measurement, all in either positive or negative mode. Through fraction collection and infusion, a significant gain in data quality is obtained along with a time-saving benefit, because the original sample needs neither to be re-analyzed by re-injection nor to be pre-concentrated. Therefore, a novel hydroxylated talinolol metabolite could be characterized with only one injection.     

The Application of Perdeuterated Polycyclic Aromatic Hydrocarbons (PAH) as Internal Standards for the Liquid Chromatographic Determination of PAH in a Petroleum Crude Oil and Other Complex Mixtures

Abstract

A sequential liquid chromatographic (LC) procedure for the determination of polycyclic aromatic hydrocarbons (PAH) in a petroleum crude oil and other complex mixtures is described. The procedure includes normal-phase LC on an aminosilane column to isolate fractions containing isomeric PAH and reversed-phase LC on a polymeric C₁₈ column to separate the individual PAH isomers. Appropriate perdeuterated PAH are added to the sample so that each isomeric fraction will contain one internal standard. The perdeuterated PAH are excellent internal standards for this sequential LC procedure. Perdeuterated PAH have normal-phase and reversed-phase LC retention characteristics similar to those of the parent PAH. In the normal-phase LC separation, the perdeuterated PAH elute in the same fraction as the parent PAH. In the reversed-phase LC separation, the perdeuterated PAH elute first and are generally resolved from the parent PAH. The optimized spectrofluorometric detection of each PAH analyte is accomplished by programming appropriate sets of excitation and emission wavelengths to correspond with the elation time of each analyte on the polymeric C₁₈ column. The analytical results obtained from this procedure for the analysis of a shale oil sample [Standard Reference Material (SRM) 1580] and a petroleum crude oil (SRM 1582) are compared to values obtained by gas chromatography - mass spectrometry.     

The use of particle beam mass spectrometry for the measurement of impurities in a nabumetone drug substance, not easily amenable to atmospheric pressure ionisation techniques

Liquid chromatography/particle beam mass spectrometry (LC/PB-MS) was used for the structural elucidation of some impurities in nabumetone as this compound poorly ionises by atmospheric pressure ionisation (API) techniques. PB-MS was optimised for nabumetone and a sensitivity study was carried out. To obtain full scan electron ionisation spectra a minimum of 100 ng of compound on column was needed. By using 20 mg/mL solutions of nabumetone, impurities at levels of about 250 ppm mass fraction relative to nabumetone could be detected. Results were compared with LC/API-MS and previous GC/MS.