Radiation-induced crosslinking and cyclization in 1,2-polybutadiene

In order to get information on the radiolytic changes in 1,2-polybutadiene (1,2-PB) the sol and gel fractions, the conversion of double bonds, the structure and concentration of radicals, the formation of dienes and the formation of gaseous products were measured. In addition, the dose rate dependence and temperature dependence for the conversion of double bonds were determined. G values for double bond conversion depend on molecular weight and range from 20 to 200. G values for crosslinking are about 10. A mechanism for the double bond conversion is proposed which involves initiation by a transformation of the primary radical ion in the vinyl group into a carbonium ion and a radical. This is supported by ESR measurement. Reaction of the carbonium ion with a vinyl group in the same chain gives rise to cyclization, whereas reaction with a vinyl group in a neighboring chain results in crosslinking. A comparison of the G values for conversion of double bonds with the G values for crosslinking shows that the formation of cyclic rings exceeds the formation of crosslinks by a factor of about 10. The corresponding values in 1,4-cis- and 1,4-trans-polybutadiene are much smaller [G(cl) ? 2; G(db) ? 7]. The pendent vinyl groups in 1,2-polybutadiene therefore are more reactive than the vinylidene groups in 1,4-polybutadienes.     

Photorearrangements of hydrocarbon polymers with pendant double bonds

A study was made of the microstructural changes that occur in ultraviolet irradiation under vacuum of thin films of 1,2-poly(cis-1,4-hexadiene) (CHD), 1,2-poly(trans-1,4-hexadiene) (THD), 1,2-poly(trans-1,3-pentadiene) (TPD), equibinary (1,2,-1,4) polybutadiene (EB), and equibinary (3,4-1,4) polyisoprene (EI). These polymers—all containing pendant double bonds—undergo important photoinduced loss of unsaturation, presumably through cyclization of the double bonds, by analogy to the previously reported photocyclization of 1,2-polybutadiene (VB) and 3,4-polyisoprene (VI)films. For the equibinary polymers, which contain internal as well as external (or pendant) double bonds, the loss of unsaturation is considered to involve photocyclization of 1,2-1,4 and 1,2-1,2 dyads in EB and of 3,4-1,4 and 3,4-3,4 dyads in EI. Accompanying thecyclization process in CHD, THD, and TPD is a direct photochemical cis-trans isomerization of ? CH?CH? double bonds analogous to that originally noted for 1,4-polybutadiene. The photorearrangements in the above polymers with pendant double bonds were compared to the corresponding thermally induced rearrangements reported previoulsy;for VB and VI, in particular, the thermal, photo-and radiation-induced cycli-zations were found to be very similar, possibly having a common nonradical, nonionic mechanism involving excited double bonds.     

Thermal rearrangements of polybutadienes with different vinyl contents

A study was made of the loss of double bonds in equibinary (1,4-1,2) polybutadiene (EB) and in polybutadienes with 30% 1,2, 70% 1,4 (FI), and 10% 1,2, 90% 1,4 (DI) double-bond content, when heated in vacuum under nonpyrolytic conditions (temperature range 220–280°C). These polymers were found to undergo second-order loss of 1,2 unsaturation with similar activation energies (E_a = 34.0 ± 3 kcal/mole), by analogy to the previously reported thermally induced loss of double bonds in 1,2-polybutadiene (VB) (E_a = 33.6 ± 3 kcal/mole). Moreover, EB and FI exhibited also second-order loss of 1,4 unsaturation, with E_a ca. 36 and 40 kcal/mole, respectively, while DI showed negligible loss of 1,4 unsaturation below 260°C, in common with cis-1,4-polybutadiene (CB) (with 2% 1,2 double bonds) examined earlier. The loss of 1,2 double bonds in the various polybutadienes with different vinyl contents is accompanied by substantial methyl production, ranging from about one methyl group formed for every 4–5 vinyl units lost in VB, to one methyl for every two vinyls lost in EB, and to almost one methyl for each vinyl lost in DI or CB. Mechanisms are proposed for the thermally induced loss of 1,2 and 1,4 unsaturation in various polybutadienes and for the accompanying methyl production.     

Ozonation of hydrocarbon diene elastomers: A mechanistic study

A study of the effects of ozonation on polybutadiene, polyisoprene, and several related hydrocarbon elastomers has shown that elastomers containing di-substituted double bonds (e.g., cis-1,4-polybutadiene) give crosslinked products as well as chain scission products in nonpolar solvents, whereas those containing tri-substituted double bonds (e.g., cis-1,4-polyisoprene) give chain scission products only. Both types of elastomer, however, give only chain scission products in polar solvents. Further investigation of the ozonation of elastomers, including the effect of ozonides of monoolefins and the solvent effect has led us to postulate that the chain scission involves the attack of a second ozone molecule on the preformed ozonide, and, the crosslinking is due to the attack of the biradical carbonyl oxide on the rubber.     

NMR and DSC investigations of the miscibility of blends of cis-1,4-polyisoprene with polybutadienes of different microstructures

Differential scanning calorimetry and torsional braid analysis investigations of the phase diagram of cis-1,4-polyisoprene/polybutadiene blends as a function of the polybutadiene microstructure were reported by several authors. Polybutadienes containing a high vinyl content were shown to be miscible with cis-1,4-polyisoprene on the DSC spatial scale, whereas polybutadienes containing a low vinyl content were immiscible. In this article, we used variable-temperature determinations of ¹H NMR free induction decays and low-temperature, high-resolution solid-state ¹³C NMR measurements of proton spin-lattice relaxation times in the rotating frame to probe the phase behavior of the cis-1,4-polyisoprene/polybutadiene blends at the smaller spatial scale of the NMR technique. Blends of cis-1,4-polyisoprene with a polybutadiene having a large number of vinyl 1,2 linkages appeared to be miscible on the molecular scale, in spite of small regions in which the polybutadiene component is not uniformily dispersed in the other polymer. On the contrary, blends in which the polybutadiene has a low content of vinyl 1,2 sequences were phase separated over the whole temperature range considered and no intermixed regions could be detected. The limiting case was observed with the polybutadiene containing 33 wt % vinyl 1,2 units, for which miscibility on a molecular scale is highly dependent on the blend composition. © 1995 John Wiley & Sons, Inc.     

Simulation of polymer network formation: Connectivity considerations

The issue of connectivity in polymer networks is discussed by employing graph theory. Several topics are addressed, including the theory of rubberlike elasticity and computer simulations of network formation. The formulation of the partition function is reviewed and new applications are presented on the irradiation cure of polybutadiene and the sulfur vulcanization of cis(1,4)-polyisoprene and cis(1,4)-polybutadiene.     

Epoxidation of syndiotactic 1,2-polybutadiene with peracids

The epoxidation of syndiotactic 1,2-polybutadiene (84 and 16% 1,2 and 1,4 units, respectively) with carboxylic peracids prepared in situ and m-chloroperbenzoic acid was studied. In the course of epoxidation in the presence of carboxylic peracids, oxirane groups are formed only through epoxidation of double bonds in the macromolecular backbone, whereas m-chloroperbenzoic acid is responsible for the chemical modification of 1,2 and 1,4 units of polybutadiene. The basic kinetic parameters of 1,2-polybutadiene epoxidation with peracids of various chemical structures were determined.     

Viscoelastic properties of 1,2-polybutadiene—comparison with natural rubber and other elastomers

Viscoelastic properties of uncrosslinked 1,2-polybutadiene (91.5% vinyl, 7.0% cis, 1.5% trans, number-average molecular weight 99,000) were studied by dynamic shear measurements between 0.15 and 600 cps (torsion pendulum and Fitzgerald transducer) and shear creep measurements over time periods up to 3.7 × 10⁴ sec., in the temperature rang from 5 to 50°C. More limited dynamic measurements were made on a sample of unvulcanized natural rubber with number-average molecular weight 350,000 at frequencies from 0.4 to 400 cps and temperatures from 13 to 48°C. All data were reduced to 25°C. by shift factors calculated from equations of the WLF form with the following coefficients: 1,2-polybutadiene, c₁ = 6.23, c₂ = 72.5; natural rubber, c₁ = 5.94, c₂ = 151.6. In the transition zone, the relative positions of the loss tangent curves on the logarithmic frequency scale for these and other rubbers (1,4-polybutadiene with 50% trans configuration; styrene–butadiene rubber with 23.5% styrene content; and polyisobutylene) provided relative measures of local segment mobility. At 25°C., these ranged over a factor of 3700 with 1,2-polybutadiene and polyisobutylene the lowest and 1,4-polybutadiene the highest. When the frequency scale of each rubber was reduced to a temperature 100°C. above its glass transition temperature, however, the loss tangent curves for all except polyisobutylene were nearly coincident; the latter still showed a lower mobility by a factor of about 1/800. The terminal relaxation time and steady-state compliance for the 1,2-polybutadiene calculated from the Rouse theory were larger than those observed experimentally. The level of compliance corresponding to the entanglement network of 1,2-polybutadiene, J_eN, was calculated by integration over the loss compliance, J″, to be 1.62 × 10^?7 cm.²/dyne; integration over G″ to obtain the corresponding modulus gave reasonable agreement. From such J_eN, values, the average number of chain atoms between entanglement points, jZ_e, was estimated as follows: 1,2-polybutadiene, 132; natural rubber, 360; 1,4-polybutadiene, 110; styrene–butadiene rubber, 186; polyisobutylene, 320. Values of jZ_e were also estimated from the minimum in the loss tangent and compared with those reported from the molecular weight dependence of viscosity. The three sources were in generally good agreement.     

Syndiotactic 1,2-polybutadiene with Co-CS2 catalyst system. III. 1H- and 13C-NMR study of highly syndiotactic 1,2-polybutadiene

The ¹H and ¹³C-NMR spectra of highly crystalline syndiotactic 1,2-polybutadiene (s-PB) are discussed in order to clarify the mechanism of butadiene polymerization with cobalt compound–organoaluminum–CS₂ catalysts. Cis opening of the double bonds in the syndiotactic polymerization is affirmed by the study of the copolymer from perdeuteriobutadiene and cis,cis-1,4-dideuteriobutadiene. S-PB (mp 210°C) has 99.7% 1,2 units, 0.3% isolated cis-1,4 units, and 99.6% syndiotacticity. Polymer ends (2-methyl-3-butenyl group and conjugated diene structure) are also determined. The differences in free energy of activation between 1,2 and cis-1,4 propagation and between syndiotactic and isotactic propagation are 14.0 and 9.6 kcal/mol, respectively, for Co(acac)₃-AlEt₃-AlEt₂Cl-CS₂, and 6.7 and 5.7 kcal/mol, respectively, for the aluminum-free Co(C₄H₆)(C₈H₁₃)CS₂ system. The conformation of s-PB in o-dichlorobenzene at 150°C is described by the sequence (tt)_1.6(gg)(tt).     

Syndiotactic 1,2-polybutadiene with Co-CS2 catalyst system. I. Preparation,properties, and application of highly crystalline syndiotactic 1,2-polybutadiene

Highly crystalline syndiotactic 1,2-polybutadiene (s-PB) having melting point (mp) up to 216°C was obtained by using a Co(acac)₃-AIEt₃-CS₂ catalyst. The polymer with mp 208°C was found to have 99.7% 1,2 content and 99.6% syndiotacticity by ¹H and ¹³C-NMR measurements. The s-PB can be molded by addition of a stabilizer such as 2,6-di-t-butyl-4-hydroxymethylphenol into fiber, film, and various shaped articles. The physical properties presented in the present article include stress-strain and dynamic mechanical behavior. The highly crystalline syndiotactic 1,2-polybutadiene was applied to a carbon fiber and UBEPOL VCR (cis-1,4-polybutadiene reinforced by fibrous syndiotactic 1,2-polybutadiene).     

Preparation of branched cis-1,4-polybutadiene in the presence of a neodymium catalyst

It was shown that branches can be incorporated into linear chains of cis-1,4-polybutadiene produced in the presence of neodymium catalysts. Branched polymers were prepared through the copolymerization of butadiene and a low-molecular-mass polybutadiene macromonomer containing a system of conjugated C=C bonds at chain ends. The incorporation of macromonomer units into the polymer chain was confirmed by the IR spectroscopic analysis of macromonomer-perdeuterobutadiene copolymers.     

Synergistic mechanical response in blends of diene polymers and their complexes with palladium chloride

The mechanical properties of atactic 1,2-polybutadiene and 3, 4-polyisoprene can be modified significantly with the addition of bis(acetonitrile)dichloropalladium(II). These weak rubbery polymers are transformed into glassy materials when the salt concentration is ≅ 4 mol %, in the absence of high-temperature annealing. Stress-strain measurements and Fourier transform infrared (FTIR) spectra for blends of cis-polybutadiene and PdCl₂, without high-temperature annealing, suggest that π-complexes form between palladium and the olefinic groups within the backbone of the polymer. These solid complexes cannot be dissolved in the original solvent (tetrahydrofuran), nor can they be disrupted by triphenylphosphine. Young's modulus of the cis-polymer is enhanced by a factor of 50 when the salt concentration is 4 mol %, and the fracture strain is approximately 300%. An exothermic process centered at ≅ 250°C accompanied by minimal weight loss suggests that PdCl₂ could trigger high-temperature dimerization reactions of the carbon–carbon double bonds in the backbone of the cis-polymer. High-temperature annealing effects on the stress-strain response of cis-polybutadiene with 4 mol % PdCl₂ are consistent with the data from calorimetry, suggesting that catalytically induced chemical crosslinking is operative at high temperatures. This latter claim is verified by infrared spectroscopy at ambient and elevated temperatures. Hence, bis(acetonitrile)dichloropalladium(II) coordinates to and catalyzes dimerization reactions of olefinic groups when they are present in the main chain or the sidegroup. This square-planar transition-metal salt also enhances the high-strain mechanical response of commercial styrene-butadiene-styrene triblock copolymers (Kraton^TM D series). Reactive blending and compatibilization with transition-metal salts are attractive strategies to modify the mechanical properties of commercially important diene-based polymers that contain unsaturation in the main chain or the sidegroup. © 1996 John Wiley & Sons, Inc.     

NMR relaxation study of crosslinked cis-1,4-polybutadiene

Proton relaxation measurements have been used to investigate the effects of crosslinking on the segmental motion in cis-1,4-polybutadiene samples. The temperature dependence of proton spin–lattice relaxation time T₁ and spin–spin relaxation time T₂ at 60 and 24.3 MHz are reported in cis-1,4-polybutadiene (PB) samples with different crosslink density including uncrosslinked PB and samples with 140, 40, and 14 repeat units between crosslinks. In addition, spin-lattice relaxation times in rotating coordinate frame, T_1p, have also been determined. The relaxation data are interpreted in terms of the effects of crosslinks on segmental chain motions. Because of their sensitivity to low-frequency motion, T₂ data are of major interest. At temperatures well above the T₁ minimum the small T₂ temperature dependence resembles solidlike behavior reflecting the nonzero averaging of dipolar interactions due to anisotropic motion of the chain segments between crosslinks. The magnitude of T₂ at 60°C is found to be proportional to the average mass between crosslinks.     

Anionic polymerization to high vinyl polybutadiene

1,3-Butadiene was polymerized anionically to polybutadiene which contained up to 100% 1,2-addition product. The atactic 100% 1,2-polybutadiene was prepared with n-butyllithium modified with bis piperidino ethane. The polymerization was done in hexane solvent at ?5 to +20°C polymerization temperature.     

Moduli of model elastomeric networks prepared from polymer chains having a high plateau modulus,and their interpretation in terms of the constrained-chain model

High-molecular weight polybutadiene chains having approximately 47% cis-1,4 units and 45% trans-1,4 units were crosslinked through their carbon-carbon double bonds using p-bis(dimethylsilyl) benzene as crosslinking agent and chloroplatinic acid as catalyst. This particular polymer was chosen because the high plateau modulus it exhibits in the un-crosslinked state is taken to indicate large numbers of chain entanglements, and stress–strain measurements on such networks have frequently been interpreted with the assumption that the trapping of such entanglements during crosslinking should contribute significantly to their modull. It is shown in the present investigation that such results are equally well interpreted in terms of the new constrained-chain theory of rubbery elasticity. © 1993 John Wiley & Sons, Inc.     

Characterization of diene polymers. I. Infrared and NMR studies: Nonadditive behavior of characteristic infrared bands

Extinction coefficients of the characteristic infrared bands due to isomeric structural units were measured for polybutadiene and polyisoprene in CS₂ or CCl₄ solutions and were compared with the isomer composition determined by NMR. The NMR signal assignments were made on the basis of the spectra of deutero derivatives of the polymers. In the case of polyisoprene, linear relations were obtained between the extinction coefficients and the isomer contents determined by NMR for the absorption bands at 1385 cm^?1 (characteristic of trans-1,4 units), 1376 cm^?1 (cis-1,4 units), and 889 cm^?1 (3,4 units). However, for the absorption bands at 840 cm^?1 (characteristic of cis-1,4 and trans-1,4 units), isomerized polyisoprenes did not give such a linear relationship. In polybutadiene, the extinction coefficient for the atactic 1,2 units was found to be lower than that of the syndiotactic 1,2 unit. These experimental facts lead to the conclusion that additivity of the extinction coefficients does not always hold for diene polymers. The deviation from the linear relation may be associated with regular sequences of one isomeric conformation in the chain.     

Oxidative stress relaxation and the measurement of sol fraction in rubber vulcanizates

A simple method to determine the chain scission mechanism of the oxidative degradation of rubber vulcanizates is proposed. The method involves the measurement of oxidative stress decay and the change in sol fraction, which allow us to distinguish whether scission occurs randomly along the main chain, near crosslinks or of crosslinks. The applicability of this method was well established using natural rubber vulcanizates as the reference samples. The chain scission of cis-1,4-polyisoprene vulcanizaties was proved to take place randomly along the main chain irrespective of their crosslink structure. On the other hand, the chain scission of dicumyl peroxide cured cis-1,4-polybutadiene takes place selectively near crosslinks. It is suggested that the unusual behavior of cis-1,4-polybutadiene vulcanizates is due to the characteristic structure of the crosslinks.     

~(13)C-NMR STUDY ON THE EQUIBINARY (cis-1,4;1,2) POLYBUTADIENE POLYMERIZED WITH IRON CATALYST

The (cis-1,4 and 1,2) polybutadiene polymerized with iron catalyst was investigated by ~(13)C-NMR. Assignments have been made on the spectra for all peaks of the aliphatic and olefinic carbons using chemical shift corrective terms together with Furukawa parameters. The relative intensities of peaks were calculated from the Bernoulli distribution of cis-1,4 and 1,2 units.Quantification of cis-1,4 and 1,2 contents, sequence distribution, alternation pattern of cis-1,4 and 1,2 units, and the chain propagation mechanism were discussed as a result of the detailed study of the spectra.     

Carbon-13 NMR of polybutadiene

By using the carbon-13 NMR technique, it is shown that there are no cis-1,4–trans-1,4 linkages in a n-BuLi-catalyzed polybutadiene. The polymer consists of “blocks” of cis-1,4 units and trans-1,4 units separated by isolated vinyl units. Preliminary evidence suggests this might also be true for other types of 1,3-diene polymerization. Some of the implications of this finding on the mechanism of polymerization are discussed. Tacticity triad distributions are readily determined in polybutadienes with high 1,2 addition contents.     

Glass-transition temperature and microstructure of polybutadienes

DSC and NMR are employed to determine the glass-transition temperatures and the structural features of polybutadienes with widely varying configuration isomeric compositions. The dependences of the glass-transition temperature on the contents of cis-1,4-, trans-1,4, and 1,2-units in polybutadiene chains are plotted and discussed. An analysis of the experimental results and the published data suggests that, in the study of the glass-transition-structure relationship, simplified approaches are inapplicable and it is necessary to consider the configurational and conformational geometry of polybutadiene chains.