Planar deformation of amorphous poly(ethylene terephthalate) by stretching and forging

The planar deformation of amorphous poly(ethylene terephthalate) (PET) was performed by stretching and by forging under comparable conditions at a series of constant temperatures, 80, 90, 100, and 110°C. The highest planar draw ratios of 4.5 × 4.5 and 3.5 × 3.5 were obtained by forging and stretching, respectively. Samples were studied before and after deformation by wide angle x-ray scattering (WAXS), differential scanning calorimetry (DSC), density measurements, and elastic recovery at 100°C. A distinct difference in efficiency of draw between these two techniques is found, as judged mainly by the straininduced crystallization. The forging is more effective than stretching in achieving stabilized planar draw under comparable process conditions.     

Surface characterization of laser-treated poly(ethylene terephthalate) by optical profilometry and scanning tunneling microscopy

Characteristic changes in the surface topography due to UV laser treatment are of high significance for the determination of material destruction thresholds and surface structure development. E.g. irradiation of poly(ethylene terephthalate) (PET) film with pulsed UV laser light of 248 nm modifies the smoth surface of the polymer into a well oriented structured surface. The development of these structures were studied with scanning tunneling microscopy (STM) and high resolution optical profilometry. Three dimensional data of the surface were taken from the samples after each laser pulse. A change of topographic data was found in relation to fluence and number of pulses applied. © 1993 John Wilcy & Sons, Inc.     

Influence of plasma treatment on the molar mass of poly(ethylene terephthalate) investigated by different chromatographic and spectroscopic methods

The influence of different types of low and atmospheric pressure plasma on poly(ethylene terephthalate) (PET) has been studied in terms of changes in molar mass and molar mass distribution. Apart from a variation of plasma gases (oxygen, helium) different types of plasma (microwave, radio frequency, corona discharge) were used for the plasma surface modification. The changes in molar mass and types of functional end groups of lower molar mass products were investigated by means of matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOFMS), whereas the high-molar mass fraction was analyzed by means of size-exclusion chromatography (SEC). The formation of crosslinked products during exposure to a helium plasma, which emits preponderately energy-rich and intense ultraviolet radiation, was proved by means of thermal field-flow fractionation (ThFFF). This method combined with a multiangle laser light scattering (MALLS) detector allows detection of weakly crosslinked polymers and microgels. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1639–1648, 1998     

Physical transitions and crystallization phenomena in poly(ethylene terephthalate) studied by microhardness

The crystallization behavior of poly(ethylene terephthalate) both with and without sodium montanate, a crystal nucleating agent, has been studied using the microhardness technique. The kinetics of crystallization from the glassy state were investigated in real time by measuring the microhardness H at different crystallization temperatures. Results are discussed in terms of the Avrami equation. Values of the Avrami exponent n of about 3 are observed for samples irrespective of nucleating agent. For samples with nucleant two crystallization ranges are observed: a first range which corresponds to a fast crystallization from nucleating agent particles and a second range which is associated with a slow self-crystallization mode. New transitions evidenced by the presence of a small maximum in H as a function of annealing time and temperature are detected at temperatures above T_g for physically aged samples. The kinetics of this transition have also been examined. It is further shown that the presence of nucleating agent induces a hardening at room temperature which is similar to the effect produced by the physical aging of the samples below T_g. Finally, it is found that aging reduces the rate of creep of the material under the indenter. © 1993 John Wiley & Sons, Inc.     

Properties of sulfonated poly(butylene terephthalate)

The synthesis, morphology, and mechanical properties of sulfonated poly(butylene terephthalate) (PBT) and its unsulfonated analogs were studied. The morphology of these copolymers crystallized from the melt were examined by a combination of wide-angle x-ray scattering (WAXS), polarized light microscopy, and small-angle light scattering (SALS). Stress-strain measurements are correlated with the morphological results. Spherulitic morphology, with a maltese cross at 45°C with respect to the crossed polars, is formed at low sulfonate levels (≤ 5.0 mol %). At a higher ion content, the maltese cross rotates 45° to form a cross pattern. At still higher sulfonate contents, typically 13 mol %, the light scattering pattern disappears completely. Microscopic and WAXS examination of these functionalized PBT copolymers confirms that the crystallinity level decreases with increasing ion content and is eliminated completely at the higher sulfonation level. The spherulite radius, however, remains invariant until the highest functionalization level. On the contrary, the morphology and properties of the unsulfonated isophthalate copolymer analogs remain relatively constant over the entire composition range examined. In several compositions clearly inferior properties are noted compared with the ion-containing copolymers.     

Crystal structure of poly(p-benzamide)

Redetermination of the crystal structure of poly(p-benzamide) was made by using newly collected intensity data. The molecular conformation is TCTC, where the internal rotation angles about the N? C bond of the amide group and about the virtual bond of N-phenyl-C are T (trans) and C (cis) conformations, respectively. Two molecular chains pass through a rectangular unit cell with dimension, a = 7.75 Å, b = 5.30 Å, c (fiber axis) = 12.87 Å, and the space group, P2₁2₁2₁-D. The reflection observed at the spacing of 010 may be attributed to the reflection due to another crystal polymorph or the diffuse scattering due to disorder. © 1993 John Wiley & Sons, Inc.     

Conformation of the ground-state dimer in poly(ethylene terephthalate)

Absorbance, excitation, and emission measurements have been performed with methyl benzoate and five model compounds, C₆H₅COO (CH₂)_xOOCC₆H₅, x = 2–6. Under appropriate conditions, three of the model compounds (those with x = 3, 4, 5) show evidence for the formation of intramolecular ground-state dimers. The model compound with x = 5 can form two types of dimers which emit with different energies. The model compound with x = 3 forms one of these dimers, and the model compound with x = 4 prefers the other ground-state dimer. Molecular modeling of the dimers suggests that the two conformations of the ground-state dimers differ in the orientation of the two C?O bonds. In the one dimer these two bonds are nearly parallel, but in the other they make an angle of about 120°. © 1993 John Wiley & Sons, Inc.     

Recovery as a measure of oriented crystalline structure in poly(ether ester)s based on poly(ethylene oxide) and poly(ethylene terephthalate) used as shape memory polymers

Poly(ether ester)s consisting of poly(ethylene oxide) and poly(ethylene terephthalate) segments, EOET copolymers, could be used as shape memory polymers (SMP). Crystalline structural characters of the copolymers during the memory process were investigated by dynamic mechanical analysis, differential scanning calorimeter, wide-angle X-ray diffraction, polarizing microscopy, and recovery measurements. PEO crystals in stretched EOET copolymer preferentially oriented along fiber axis or stretch direction. During stretching, the structure of the copolymer undertake a transformation from spherulite to fiber, resulting in a crystalline morphology similar to shish-kebab, and recovery properties of stretched EOET samples were dependent on as-described crystalline structural characters that can be influenced by draw ratio. Driving forces for contraction come from the oriented chains, and only oriented or extended chains can be contributive to the recovery of deformation; these extended chains involve both crystalline and amorphous segments. The recovery process in shape memory behavior was noticed to be deorientation of oriented chains due to thermodynamic entropy effect, and was divided into three stages. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 101–112, 1999     

The influence of vacuum-ultraviolet radiation on poly(ethylene terephthalate)

Poly(ethylene terephthalate) was exposed to radiation from different kinds of low-pressure plasmas in an oxygen atmosphere. The lower wavelength limit of the spectrum investigated, λ = 112 nm, is the cut-off of magnesium fluoride used for separating the specimen chamber from the plasma light source. The total surface oxygen concentration, and the formation of hydroxyl, carbonyl, and carboxyl groups were evaluated from XPS measurements in combination with chemical derivatizations, and their dependences on the radiation spectrum and the oxygen pressure in the sample chamber have been investigated. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

High‐pressure DTA of poly(butylene terephthalate), poly(hexamethylene terephthalate), and poly(ethylene terephthalate)

Pressure effect on the melting behavior of poly(butylene terephthalate) (PBT) and poly(hexamethylene terephthalate) (PHT) was studied by high‐pressure DTA (HP‐DTA) up to 320 and 530 MPa, respectively. Cooling rate dependence on the DSC melting curves of the samples cooled from the melt was shown at atmospheric pressure. Stable and metastable samples were prepared by cooling from the melt at low and normal cooling rates, respectively. DTA melting curves for the stable samples showed a single peak, and the peak profile did not change up to high pressure. Phase diagrams for PBT and PHT were newly determined. Fitting curves of melting temperature (T_m) versus pressure expressed by quadratic equation were obtained. Pressure coefficients of T_m at atmospheric pressure, dT_m/dp, of PBT and PHT were 37 and 33 K/100 MPa, respectively. HP‐DTA curves of the metastable PBT showed double melting peaks up to about 70 MPa. In contrast, PHT showed them over the whole pressure region. HP‐DTA of stable poly(ethylene terephthalate) (PET) was also carried out up to 200 MPa, and the phase diagram for PET was determined. dT_m/dp for PET was 49 K/100 MPa. dT_m/dp increased linearly with reciprocal number of ethylene unit. The decrease of dT_m/dp for poly(alkylene terephthalate) with increasing a segmental fraction of an alkyl group in a whole molecule is explained by the increase of entropy of fusion. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 262–272, 2000     

Effects of the drawing form and draw ratio on the fiber structure and mechanical properties of CO2-laser-heated-drawn poly(ethylene terephthalate) fibers

The structure, mechanical properties, and thermomechanical properties of poly(ethylene terephthalate) (PET) fibers obtained by laser-heated drawing were investigated in terms of their dependence on the draw ratio and feed speed and the differences between neck-drawn fibers and flow-drawn fibers. The long period at a draw ratio of 6.0 reached 19.0 nm, notably larger than at lower ratios, whereas the tilting angle of the laminar structure was constant at about 60°, regardless of the draw ratio. A maximum value of 15.0 GPa was attained for the initial modulus, and 1.07 GPa was attained for the tensile strength. A higher tensile strength orientation-induced crystallized fiber at the same initial modulus was obtained from higher molecular weight PET. The relationship between the compliance and molecular orientation of the amorphous phase was studied with a series model of crystalline and amorphous phases. The results revealed that, in the high-draw-ratio fibers, the compliance of the amorphous phase decreased with the draw ratio at a higher rate than indicated by extrapolation to intrinsic values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 79–90, 2004     

Rapid crystallization and thermoreversible gelation of poly(ethylene terephthalate) in polymer/oligomer binary system

Poly(ethylene terephthalate) (PET) was rapidly crystallized through thermoreversible gelation in a liquid ethylene glycol oligomer or in epoxy resin. The solutions formed gel rapidly on cooling. Polarized light microscopy and small-angle light scattering showed that these gels contain large, regular PET spherulites. The gels may be formed by two consecutive processes: the phase separation and crystallization, and gelation by formation of a three-dimensional PET network in the oligomer solvents, where the nodes of the network are PET spherulites. The crystallinity of PET recovered from polymer/oligomer gels is near 72% measured by wide-angle X-ray diffraction method, which is about 20% higher than PET samples crystallized by solution crystallization in small molecule solvent, high temperature annealing, and stretching techniques. It takes only a few minutes to form the highly crystalline phase PET in the PET/oligomer system, and the crystallinity of the dried gel is independent of the concentration of the original solution. Excimer-fluoresence and Raman spectroscopic studies indicated that PET recovered from the gels are in an ordered state with few chain entanglements. The entanglement density of the recovered PET recovered from a 20 wt % solution in ethylene glycol oligomer is as low as that of freeze-extracted PET from a 0.5 wt % solution in phenol. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1219–1225, 1998     

Atomic force microscopy investigation of cold‐plasma‐treated poly(ethyleneterephthalate) textiles

Atomic force microscopy (AFM) has been applied to investigate the morphological and topographical surface modifications induced by radiofrequency cold plasma processing of poly(ethyleneterephthalate) textiles. Surface effects are analysed in low‐pressure air plasma for different plasma exposure times. The results show a progressive degradation of the surface with increasing roughness. The analysis suggests that modification of the surface during textile treatment may be ascribed to a plasma‐induced physical process. Copyright © 2003 John Wiley & Sons, Ltd.     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Effect of poly(ethylene oxide) on the structure and properties of poly(vinyl alcohol)

To improve the drawability of poly(vinyl alcohol) (PVA) thermal products, poly(ethylene oxide) (PEO), a special resin with good flexibility, excellent lubricity, and compatibility with many resins, was applied, and the Fourier transform infrared spectroscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WXRD) were adopted to study the hydrogen bonds, water states, thermal properties, crystal structure, and nonisothermal crystallization of modified PVA. It was found that PEO formed strong hydrogen bonds with water and PVA, thus weakened the intra‐ and inter‐hydrogen bonds of PVA, changed the aggregation states of PVA chains, and decreased its melting point and crystallinity. Moreover, the interactions among PVA, water, and PEO retarded the water evaporation and made more water remain in the system to plasticize PVA. The existence of PEO also slowed down the melt crystallization process of PVA, however, increased the nucleation points of system, thus made more and smaller spherulites formed. The weakened crystallization capability of PVA and the lubrication of PEO made PVA chains to have more mobility under the outside force and obtain high mechanical properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1946–1954, 2010     

Synthesis,physical characterization,and acetone sorption kinetics in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Random copolymers of poly(ethylene terephthalate) (PET) and poly(ethylene 2,6-naphthalate) (PEN) were synthesized by melt condensation. In a series of thin, solvent cast films of varying PEN content, acetone diffusivity and solubility were determined at 35°C and an acetone pressure of 5.4 cm Hg. The kinetics of acetone sorption in the copolymer films are well described by a Fickian model. Both solubility and diffusivity decrease with increasing PEN content. The acetone diffusion coefficient decreases 93% from PET to PET/85PEN, a copolymer in which 85 weight percent of the dimethyl terephthalate in PET has been replace by dimethyl naphthalate 2,6-dicarboxylate. The acetone solubility coefficient in the amorphous regions of the polymer decreases by approximately a factor of two over the same composition range. The glass/rubber transition temperatures of these materials rise monotonically with increasing PEN content. Copolymers containing 20 to 80 wt % PEN are amorphous. Samples with <20% or >80% PEN contain measurable levels of crystallinity. Estimated fractional free volume in the amorphous regions of these samples is lower in the copolymers than in either of the homopolymers. Relative free volume as probed by positron annihilation lifetime spectroscopy (PALS) decreases systematically with increasing PEN content. Acetone diffusion coefficients correlate well with PALS results. Infrared spectroscopy suggests an increase in the fraction of ethylene glycol units in the trans conformation in the amorphous phase as the concentration of PEN in the copolymer increases. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2981–3000, 1998     

Solvent-induced crystallinity in poly(aryl-ether-ether-ketone) [PEEK]

The amount and structure of the crystals formed by the solvent-induced crystallization (SIC) following a sorption-desorption cycle of five fluids (benzene, toluene, chloroform, methylene chloride, and carbon disulfide) in amorphous PEEK was determined by wideangle x-ray scattering (WAXS). The SIC crystal structure was compared with that produced by thermal methods, both those formed at low temperature by heating the amorphous material 10–20°C above T_g or by cooling from the melt. Although smaller in size, the SIC crystals are tighter and more organized than those produced thermally. The WAXS data indicates that all five fluids produce approximately 35% crystallinity in PEEK. Gravimetric data suggest that a low-density region, consisting of either microvoids or highly disordered amorphous region, surrounds the crystals.     

Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.