Fluorocyclopropanes. IV. Copolymers of perfluorocyclopropene

Perfluorocyclopropene undergoes free-radical copolymerization with ethylene, isobutylene, cis- and trans-2-butene, vinyl acetate, methyl vinyl ether, vinyl chloride, styrene, acrylonitrile, tetrafluoroethylene, vinyl fluoride, and vinylidene fluoride. The copolymerization proceeds most readily with electron-rich olefins such as methyl vinyl ether (to yield a 1:1 copolymer), but conditions were found to give copolymers with electron-deficient olefins such as tetrafluoroethylene and vinylidene fluoride. Copolymers with methyl vinyl ether, tetrafluoroethylene, vinyl fluoride, and vinylidene fluoride were examined in detail. Evidence is presented that the perfluorocycloproply ring is incorporated intact into the copolymer and can be subsequently isomerized to a perfluoropropenyl unit by heating at 200–300°C.     

Copolymers of 1-methylcyclopropene

1-Methylcyclopropene (MCP) copolymerizes rapidly with acrylic and vinyl monomers to form soluble, high molecular weight products containing enchained cyclopropane rings. The high electron availability in the cyclopropene double bond promotes one-to-one alternating copolymerization with sulfur dioxide, maleic anhydride, acrylic acid, acrylonitrile, dialkyl fumarates and acrylic esters. Nonalternating copolymers are obtained with vinyl chloride and vinyl acetate, and attempted copolymerization fails entirely with styrene, α-methylstyrene and isoprene. This pattern of copolymerization reactivity resembles that of highly compressed ethylene. Methylcyclopropene copolymers have high glass temperatures in spite of the small size of the MCP unit. The combination of high T_g and small size allows preparation of copolymers with high T_g having a wide range of ductilities and cohesive energy densities.     

Thermal analysis and FT‐IR studies of adsorbed poly(ethylene‐stat‐vinyl acetate) on silica

Adsorbed poly(ethylene‐stat‐vinyl acetate) (PEVAc) on fumed silica was studied using temperature‐modulated differential scanning calorimetry (TMDSC) and FT‐IR spectroscopy. The properties of the copolymers were compared with poly(vinyl acetate) (PVAc) and low density polyethylene (LDPE) as references. TMDSC analysis of the copolymer‐silica samples in the glass transition region was complicated for the copolymers because of the ethylene crystallinity. Nevertheless, examination of the glass transition region for small adsorbed amounts of these copolymers indicated the presence of tightly‐ and loosely‐bound polymer segments, similar to other polymers which have an attraction to silica. Compared with bulk polymers with the same composition, the tightly‐bound polymers showed an increased glass transition temperature (T_g) and a loosely‐bound fraction with a lower T_g than bulk. FT‐IR spectra of the surface copolymers indicated that the fraction of bound carbonyls (p) increased as the fraction of vinyl acetate in the copolymers decreased, consistent with the notion that the carbonyls from vinyl acetate preferentially find their way to the silica surface. Spectra from samples with different adsorbed amounts of polymer were used to obtain the amount of bound polymer (M_b) and the ratio of molar absorption coefficients of bound carbonyls to free carbonyls (X). The copolymers had very large p values (up to 0.8) at small adsorbed amounts and dependent on the composition of the polymer. However, an analysis of the bound fractions, based on only the vinyl acetate groups, superimposed the data, suggesting that the ethylene units simply dilute the vinyl acetate groups in the surface polymer. The sample with the smallest fraction of vinyl acetate did not show this behavior and may be considered to be “carbonyl poor.” © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 727–736     

Characterization of copolymers of vinyl acetate with ethyl α-cyanocinnamate

Alternating and random copolymers of ethyl α-cyanocinnamate and vinyl acetate were studied. Infrared, ¹H, and ¹³C spectra of the copolymers are discussed by comparison with a model compounds, poly(vinyl acetate), and various copolymers. The decomposition temperature and T_g of copolymers of various composition, studied by TMA and DSC, increase both with increasing content of ethyl α-cyanocinnamate.     

Ring-opening polymerization of 2,3,5,6-tetrasubstituted-3,4-dihydro-2H-pyrans and their copolymerization behaviors. Syntheses of alternating head-to-head vinyl copolymers and their properties

2-Methoxy-6-ethoxy-5-cyano-3,4-dihydro-2H-pyran ( 1 a), 2-isobutoxy-6ethoxy-5-cyano-3,4-dihydro-2H-pyran ( 1 b), and 2,6-diethoxy-3-methyl-5-cyano-3,4-dihydro-2H-pyran ( 1 c) were prepared by (4 + 2) cycloaddition reaction of ethyl α-cyanoacrylate with the corresponding vinyl ethers. Compounds 1 a-c were ring-open polymerized by cationic catalyst to obtain alternating head-to-head (H? H) copolymers. For comparison, head-to-tail (H? T) copolymer 3 a was also prepared by free radical copolymerization of the mixture of the corresponding monomers. The H–H copolymer exhibited minor differences in its ¹H-NMR and IR spectra, but in the ¹³C-NMR spectrum significant differences were shown between the H? H and H? T copolymers. Glass transition temperature (T_g) of H? H copolymer was higher than that of the corresponding H? T copolymer, but thermal decomposition temperature of the H? H copolymer was lower than that of the H? T copolymer. Compounds 1 a and 1 b copolymerized well with styrene by cationic catalyst, but compound 1 c failed to copolmerize with styrene. All of the H-H and H-T copolymers were soluble in common solvents and the inherent viscosities were in the range 0.2–0.5 g/dL.     

High Tg microspheres by dispersion copolymerization of N‐phenylmaleimide with styrenic or alkyl vinyl ether monomers

Solution and dispersion copolymerizations of N‐phenylmaleimide (PMI) with either styrenics or alkyl vinyl ethers (AVEs), systems with a tendency to give alternating polymers, were investigated with the goal of producing high glass transition particles. Equimolar solution copolymerization of PMI with styrenics gave alternating copolymers, whereas AVEs gave PMI‐rich copolymers (～65:35) except for t‐butyl vinyl ether, which gave copolymers with only a slight excess of PMI. These copolymers had glass transition temperatures (T_gs) ranging from 115 to 225 °C depending on comonomer(s). Dispersion copolymerization in ethanol‐based solvents in the presence of poly(vinylpyrrolidone) as steric stabilizer led to narrow‐disperse microspheres for many copolymers studied. Dispersion copolymeriations of PMI with styrenics required good cosolvents such as acetonitrile or methyl ethyl ketone as plasticizers during particle initiation and growth. Dispersion copolymerizations generally resulted in copolymer particles with compositions and T_gs very similar to those of the corresponding copolymers formed by solution polymerization, with the exception of t‐butyl vinyl ether (tBVE), which now behaved like the other AVEs. Dispersion terpolymerizations of PMI (50 mol %) with different ratios of either n‐butylstyrene and t‐butylstyrene or n‐butyl vinyl ether and tBVE led to polymer particles with T_gs that depended on the ratio of the two butyl monomers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Thermal diffusion and molecular weight calibration of poly(ethylene-co-vinyl acetate)s by thermal field-flow fractionation

Copolymer characterization is accomplished with respect to measurement of thermal diffusion coefficient (D_T) and molecular weight determination by thermal field-flow fractionation. The examined copolymers are the eight poly(ethylene-co-vinyl acetate)s [P(E-V)] having different compositions of vinyl acetate ranging from 25 to 70% and the molecular weight from 110,000 to 285,000, and three polyvinyl acetate standards as component homopolymer. The carrier solvents are tetrahydrofuran, toluene, and chlorobenzene which have different viscosities and thermal conductivities. Measured D_T values vary from 1.36 × 10^?8 to 5.97 × 10_?8 cm²/(s . K) which are dependent on the composition of copolymers and types of carriers. These values increase linearly with the increase of weight percent of vinyl acetate. It is possible to estimate D_T values of polyethylene from the extrapolated intercept in the plots of D_T vs. vinyl acetate wt % of copolymer. Tetrahydrofuran is found to be the appropriate carrier solvent for the separation of P(E-V) copolymers since D_T varies greatly with the increase of wt % in THF. Attempts are made to correlate the measured retention data with molecular sizes of copolymers for the construction of the molecular weight calibration curve. Good correlations (r² ≥ 0.931) are found in which D/D_T values of polymers vary inversely with the product of hydrodynamic volume by weight ratio of vinyl acetate. Based on this relationship, the unknown molecular weight of copolymer sample can be determined from component homopolymers for which standards are readily available. © 1995 John Wiley & Sons, Inc.     

Novel Copolymers of Vinyl Acetate and Alkyl Ring‐Substituted 2‐Phenyl‐1,1‐dicyanoethylenes

Electrophilic trisubstituted ethylene monomers, alkyl ring‐substituted 2‐phenyl‐1,1‐dicyanoethylenes, RC₆H₄CH?C(CN)₂ (where R is 2‐methyl, 3‐methyl,4‐methyl, 4‐ethyl, 4‐isopropyl, 4‐butyl, and 4‐t‐butyl), were synthesized by piperidine catalyzed Knoevenagel condensation of ring‐substituted benzaldehydes and malononitrile, and characterized by CHN elemental analysis, IR, ¹H‐ and ¹³C‐NMR. Novel copolymers of the ethylenes and vinyl acetate were prepared at equimolar monomer feed composition by solution copolymerization in the presence of a radical initiator (ABCN) at 70°C. The composition of the copolymers was calculated from nitrogen analysis, and the structures were analyzed by IR, ¹H and ¹³C‐NMR, GPC, DSC, and TGA. High T_g of the copolymers, in comparison with that of polyvinyl acetate, indicates a substantial decrease in chain mobility of the copolymer due to the high dipolar character of the trisubstituted ethylene monomer unit. The gravimetric analysis indicated that the copolymers decompose in the 190–700°C range.     

Synthesis and characterization of graft copolymers of poly(vinyl chloride) with styrene and (meth)acrylates by atom transfer radical polymerization

Graft copolymers of poly(vinyl chloride) with styrene and (meth)acrylates were prepared by atom transfer radical polymerization. Poly(vinyl chloride) containing small amount of pendent chloroacetate units was used as a macroinitiator. The formation of the graft copolymer was confirmed with size exclusion chromatography (SEC), ¹H NMR and IR spectroscopy. The graft copolymers with increasing incorporation of butyl acrylate result in an increase of molecular weight. One glass transition temperature (T_g) was observed for all copolymers. T_g of the copolymer with butyl acrylate decreases with increasing content of butyl acrylate.     

Breadth of glass transition temperature in styrene/acrylic acid block,random, and gradient copolymers: Unusual sequence distribution effects

Block, random, and gradient copolymers of styrene (S) and acrylic acid (AA) are synthesized by conventional or controlled radical polymerization, and their glass transition temperature (T_g) behaviors are compared. The location and breadth of the T_gs are determined using derivatives of differential scanning calorimetry heating curves. Each S/AA random copolymer exhibits one narrow T_g, consistent with a single phase of limited compositional nanoheterogeneity. Block copolymers exhibit two narrow T_gs originating from nanophase separation into ordered domains with nearly pure S or nearly pure AA repeat units. Each gradient copolymer exhibits a T_g response with a ～50–56 °C breadth that extends beyond the upper T_g of the block copolymers. For copolymers of similar composition, the maximum value in the gradient copolymer T_g response is consistent with that of a random copolymer, which has an enhanced T_g relative to poly(acrylic acid) due to more effective hydrogen bonding when AA units are separated along the chain backbone by S units. These results indicate that gradient copolymers with ordered nanostructures can be rationally designed, which exhibit broad glass transitions that extend to higher temperature than the T_gs observed with block copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2842–2849, 2007     

Thermal properties of poly(methyl methacrylate-co-butyl acrylate-co-acrylic acid) modified with divinyl benzene and vinyltrimethoxysilane

The effect of butyl acrylate (BA), divinyl benzene (DVB) and vinyltrimethoxysilane (TMVS) on the thermal properties of poly(methyl methacrylate-co-butyl acrylate-co-acrylic acid) was investigated. Glass transition temperature (T_g), melting temperature (T_m) and specific heat capacity of the copolymers were investigated using Differential Scanning Calorimetry. Thermal stability of the copolymers which is associated with the degradation temperature (T_d) was studied by Thermogravimetric Analysis. Polyacrylates with T_g ranges between -19°Cand 19°C were obtained. With the incorporation of >7 wt% of DVB, the T_g of the copolymer increases from about ?17°C to ?10°C even though they have not undergone UV irradiation. Gel content results prove that crosslinking has occurred in the copolymers. With increasing amount of TMVS from 0 wt% to 7 wt%, the T_m of the copolymers prepared at acidic pH is about 40-60°C higher than that at the alkaline pH. However, the addition of TMVS gives no significant effect to the T_g and T_d of the copolymer films. The thermal stability of the copolymer has improved with increasing amount of BA and DVB, with DVB being more effective. The highest T_d of 425°C with 8% of DVB has been obtained. Consequently, a polyacrylate copolymer with a T_g of about ?13°C, a T_m of 170 °C and a T_d of about 424°C has been successfully synthesized. Hence, the soft polyacrylate with its relatively high T_m and T_d could serve as a superb material especially to be applied in the areas that require high melting temperature and good thermal stability.     

Synthesis and characterization of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane: Homo‐ and copolymerization with fluorovinyl monomers

The synthesis of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane (D), its radical homopolymerization, and copolymerization with fluoroolefins are presented. Fluorodioxolane (D) was synthesized through direct fluorination of the corresponding hydrocarbon precursor in a fluorinated solvent by F₂/N₂ gas. It was polymerized in bulk using perfluorodibenzoyl peroxide as the initiator. The resulting homopolymer had a limited solubility in fluorinated solvents, and its glass transition temperature (T_g) was in the range of 180–190 °C. The polymeric films prepared by casting from hot hexafluorobenzene (HFB) solution were transparent with low refractive index (1.329 at 633 nm). These films were thermally stable (T_d > 350 °C), and were hard and brittle. The copolymers of monomer (D) were prepared with fluorovinyl monomers such as chlorotrifluoroethylene (CTFE), perfluoropropyl vinyl ether, perfluoromethyl vinyl ether, and vinylidene fluoride. The kinetics of radical copolymerization of monomer (D) with CTFE led to the assessment of the reactivity ratios of both comonomers: r_D = 3.635 and r_CTFE = 0.737 at 74 °C, respectively. The copolymers obtained were soluble in HFB and perfluoro‐2‐butyltetrahydrofuran, with T_g in the range of 84–145 °C depending on the copolymer composition. The films of the copolymers were flexible and clear with a low refractive index (1.3350–1.3770 at 532 nm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6571–6578, 2009     

Synthesis of methyl methacrylate,styrene, and isobutylene multiblock copolymers using atom transfer and cationic polymerization

ABCBA‐type pentablock copolymers of methyl methacrylate, styrene, and isobutylene (IB) were prepared by the cationic polymerization of IB in the presence of the α,ω‐dichloro‐PS‐b‐PMMA‐b‐PS triblock copolymer [where PS is polystyrene and PMMA is poly(methyl methacrylate)] as a macroinitiator in conjunction with diethylaluminum chloride (Et₂AlCl) as a coinitiator. The macroinitiator was prepared by a two‐step copper‐based atom transfer radical polymerization (ATRP). The reaction temperature, ?78 or ?25 °C, significantly affected the IB content in the resulting copolymers; a higher content was obtained at ?78 °C. The formation of the PIB‐b‐PS‐b‐PMMA‐b‐PS‐b‐PIB copolymers (where PIB is polyisobutylene), prepared at ?25 (20.3 mol % IB) or ?78 °C (61.3 mol % IB; rubbery material), with relatively narrow molecular weight distributions provided direct evidence of the presence of labile chlorine atoms at both ends of the macroinitiator capable of initiation of cationic polymerization of IB. One glass‐transition temperature (T_g), 104.5 °C, was observed for the aforementioned triblock copolymer, and the pentablock copolymer containing 61.3 mol % IB showed two well‐defined T_g's: ?73.0 °C for PIB and 95.6 °C for the PS–PMMA blocks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3823–3830, 2005     

α-Trifluoromethyl vinyl acetate. II

Low conversion, low molecular weight homopolymers of α-trifluoromethyl vinyl acetate have been obtained by pyridine initiation and also by employing very large amounts of benzoyl peroxide. Since allylic hydrogens are not present, it appears that the limiting factor in the polymerization of isopropenyl esters is a slow rate of chain growth rather than degradative chain transfer. Copolymerization of the fluoromonomer (M₂) with vinyl acetate (M₁) yields values of r₁ = 0.25 and r₂ = 0.20, and for the fluoromonomer values of 0.069 and 1.51, respectively, for Q and e. Whereas ultraviolet initiation of equimolar mixtures of α-trifluoromethyl vinyl acetate and vinyl acetate yields low molecular weight copolymers, diisopropyl percarbonate-initiated room temperature bulk copolymerizations and emulsion copolymerizations yield polymers of high DP . Differential thermal analysis of an equimolar copolymer of vinyl acetate and the fluoromonomer surprisingly yields a sharp endotherm reminiscent of crystalline polymers. The unhydrolyzed copolymers in acetone and the alcoholyzed copolymers in 0.1N alkali exhibit Huggins k′ values of 0.3–0.4. Like ordinary poly(vinyl alcohol), the polyfluoroalcohols lose viscosity in dilute alkali due to retrograde aldol condensations. The solubilities of the polyfluoroalcohols, together with their thermal behavior, NMR spectrum, polarized infrared spectrum, refractive index, abilities to form visible polarizers, and other properties are also described.     

1:1 alternating copolymer of acrylonitrile and vinyl acetate

Copolymerization of the acrylonitrile-zinc chloride complex with excess vinyl acetate has been investigated. Alternating 1:1 copolymers of acrylonitrile and vinyl acetate of high molecular weights have been successfully prepared. The alternating structure has been ascertained by means of high-resolution nuclear magnetic resonance spectroscopy. The copolymer is amorphous (T_g = 85°C) and has shown thermal and oxidative stability better than those of polyacrylonitrile. The copolymer is soluble in acetone as well as in more powerful solvents such as dimethylformamide, dimethyl sulfoxide, nitromethane, and N-methylpyrrolidone. The copolymer has been processed into films and fibers from its acetone solutions. Films show tensile properties similar to those of cellulose acetate under ambient conditions; they suffer drastic loss in tensile properties at above 50°C and retain their good tensile properties at subzero temperatures (determined as low as ?40°C). Fibers show tensile properties comparable to those of modacrylic fibers under ambient conditions but suffer marked loss in stiffness at 40°C in water and 60°C in air. The fibers also retain their good properties at subzero temperatures (measured down to ?60°C).     

Thermal stability of copolymers of vinyl acetate and methyl acrylate

The thermal degradation of a series of copolymers of vinyl acetate and methyl acrylate and the two homopolymers poly(vinyl acetate) and poly(methyl acrylate) obtained using Ce(IV) as initiator has been investigated using differential thermal analysis (DTA) and thermogravimetry (TGA) in dynamic nitrogen. The kinetic parameters E, n, and A have been obtained following several methods of thermogravimetric analyses. The stability increases as the methyl acrylate content in the copolymer composition increases. The incorporation of 5 mol % of vinyl acetate in the copolymer produces a marked decrease in stability compared to the homopolymer poly(methyl acrylate). There is evidence for an intramolecular lactonization process in vinyl acetate—methyl acrylate copolymers.     

Copolymers of vinyl fluoride

Vinyl fluoride was polymerized by photochemical initiation in a continuous-flow cylindrical reactor at room temperature and at pressures of up to 30 atm. Copolymers with vinyl acetate were prepared in order to improve the solubility and processability of poly(vinyl fluoride) (PVF). The copolymers were hydrolyzed to the corresponding vinyl alcohol copolymers and yielded hydrophilic films that are strong and flexible only when swollen by water. It was found that on hydrolysis the T_g, T_m, and heat of fusion as well as degree of crystallinity increased. It was suggested that PVF and the copolymers with vinyl alcohol are isomorphous.     

Styrene 4‐vinylbenzocyclobutene copolymer for microelectronic applications

Styrene and 4‐vinylbenzocyclobutene (vinyl‐BCB) random copolymers were prepared by free radical polymerization and studied for suitability as a dielectric material for microelectronic applications. The percentage of vinyl‐BCB in the copolymer was varied from 0 to 26 mol % to optimize the physical and mechanical properties of the cured copolymer as well as the cost. Copolymer in which 22 mol % of vinyl‐BCB was incorporated along with styrene produced a thermoset polymer which, after cure, did not show a T_g before decomposition at about 350 °C. The polymeric material has a very low dielectric constant, dissipation factor, and water uptake. The fracture toughness of the copolymer was improved with the addition of 20 wt % of a star‐shaped polystyrene‐block‐polybutadiene. Blends of the poly(styrene‐co‐vinyl‐BCB) with the thermoplastic elastomer provided material that maintained high T_g of the cured copolymer with only a slight decrease in thermal stability. The crosslinked styrenic polymer and toughened blends possess many properties that are desirable for high frequency‐high speed mobile communication applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2799–2806, 2008     

The estimation of phase modifications in polymers by the method of “molecular probes” in gas chromatography—II. The study of (acrylonitrile-α-methyl styrene) copolymers and of (acrylonitrile-vinyl acetate-α-methyl styrene) terpolymers

The application of “reciprocal chromatography” to study of the glass transitions in copolymers and terpolymers of acrylonitrile with α-methyl styrene and vinyl acetate shows specific influences of the comonomers on the characteristic T_g of the polymers. However, these influences seem very complex, and besides a “cryoscopic” effect (a lowering of the T_g regions of polyacrylonitrile with increasing content of comonomer) the effect of acrylonitrile on the T_g values of the copolymers seems less evident.     

Radical copolymerization of 3-tri-n-butylstannylstyrene with several vinyl monomers

The free radical homopolymerization and copolymerization of 3-tri-n-butylstannylstyrene (3-BTS) with styrene (ST), ethyl acrylate (EA), methyl methacrylate (MMA), vinyl acetate (VA), and acrylonitrile (AN) were carried out using 2,2′-azobisisobutyronitrile (AIBN) at 60°C. It was found that the yield of conversion to poly(3-BTS) increased with the molar ratio of initiator to monomer as well as with polymerization time. The conversion at equilibrium after 50 h was about 40%. The compositions of copolymer samples were determined from elemental analyses. Monomer reactivity ratio and Q-e values were calculated. The copolymers of 3-BTS-MMA and 3-BTS-AN were found to be alternating. The copolymers of 3-BTS with MMA, EA and AN were not soluble in any of a large number of organic solvents tested. The insolubility is believed to be due to formation of intermolecular coordination among the tributylstannyl moiety and the carbonyl or cyano groups of the polymer. These copolymers, however, were “soluble” in trihaloacetic acid, but this solubility was due to a cleavage of the trialkyltin moiety from the phenyl groups. The glass temperatures, T_g, and melting temperatures T_m, of the various polymers were also studied.