CP/MAS ~(13)C NMR技术对木浆纤维微观结构的研究

利用交叉极化结合魔角旋转技术~(13)C核磁共振法(CP/MAS ~(13)C NMR)对桉木浆纤维的微观结构进行研究,为进一步研究木质纤维素材料开发过程中反应障碍特征奠定基础.通过对NMR光谱C1区(δ 102～108)进行洛仑兹拟合,得到桉木浆纤维中纤维素Iα的相对含量为26.92%,纤维素Iβ的相对含量为52.04%,主要以纤维素Iβ晶体形式为主.通过计算纤维素C4结晶区(δ 86～92)和非结晶区(δ 80～86)的相对含量得到桉木浆的纤维素结晶度为47%.通过洛仑兹和高斯函数的混合模型对NMR光谱C4区(δ 80～92)进行拟合得到基原纤尺寸和微原纤横向尺寸分别为4.0与17.9 nm,并通过计算不同形态的结晶纤维素的相对含量得到纤维素结晶度为51%,证实了在微原纤内部次晶纤维素的存在.     

Molecular modeling simulation and experimental measurements to characterize chitosan and poly(vinyl pyrrolidone) blend interactions

Blends of chitosan and poly(vinyl pyrrolidone) (PVP) have a high potential for use in various biomedical applications and in advanced drug‐delivery systems. Recently, the physical and chemical properties of these blends have been extensively characterized. However, the molecular interaction between these two polymers is not fully understood. In this study, the intermolecular interaction between chitosan and PVP was experimentally investigated using ¹³C cross‐polarization magic angle‐spinning nuclear magnetic resonance (¹³C CP/MAS NMR) and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). According to these experimental results, the interaction between the polymers takes place through the carbonyl group of PVP and either the OH? C₆, OH? C₃, or NH? C₂ of chitosan. In an attempt to identify the interacting groups of these polymers, molecular modeling simulation was performed. Molecular simulation was able to clarify that the hydrogen atom of OH? C₆ of chitosan was the most favorable site to form hydrogen bonding with the oxygen atom of C?O of PVP, followed by that of OH? C₃, whereas that of NH? C₂ was the weakest proton donor group. The nitrogen atom of PVP was not involved in the intermolecular interaction between these polymers. Furthermore, the interactions between these polymers are higher when PVP concentrations are lower, and interactions decrease with increasing amounts of PVP. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1258–1264, 2008     

聚醚醚酮醚酮的合成与表征

聚醚醚酮（ＰＥＥＫ）自工业化以来［１］，由于其优异的性能已在机械、航天等领域得到广泛应用．各种聚芳醚酮类聚合物相继被开发出来．但以亲电缩聚路线制备聚醚醚酮醚酮（ＰＥＥＫＥＫ）的报道较少［２］．本文以二苯醚和４－氟苯甲酰氯为主要反应试剂，采取付氏酰基化...     

New Poly - and Bis(crown ether)s as Extracting Reagents

Abstract

New poly- and bis(crown ether)s containing benzo-15-crown-5 or benzo-18-crown-6 moieties were synthesized as extracting reagents, and by a preliminary solvent extraction of alkali metal picrates the poly- and bis-(crown ether)s were found to extract the cations capable of forming sandwich-type 2:1 complexes more effectively than their monomeric analogs.     

Sequence analysis of poly (ether sulfone) copolymers by 13C NMR

Random and block copolymers of poly (ether sulfone) (PES) and poly (ether ether sulfone) (PEES) were synthesized by the nucleophilic polycondensation of 4,4′‐dichlorodiphenyl sulfone (DCDPS) with 4,4′‐dihydroxydiphenyl sulfone (DHDPS) and hydroquinone (HQ). Chemical structures of these copolymers were characterized by ¹³C NMR. The monomer molar fraction, sequential distribution, and degree of randomness of the copolymers were determined through analyses of the resonances of quaternary carbons in the DCDPS unit. Experimental results show that the molar fractions of the comonomer determined by ¹³C NMR analyses are close to the charged values in the synthetic step. Moreover, these copolymers, which were prepared by different polymerization methods, revealed different number‐average sequential length and degree of randomness. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1624–1630, 2005     

Synthesis and crosslinking of poly (aryl ether)s containing 1,1-diphenylethylene moieties

Poly (aryl ether)s containing the diphenylethylene moiety, synthesized from 1,1-bis(4-fluo-rophenyl)ethylene or 1,1-bis(4-hydroxyphenyl)ethylene, are thermally crosslinkable. Char-acterization and crosslinking studies of these polymers were carried out by GPC, DSC, TGA, and NMR. The solvent resistance and T_g's of the resulting crosslinked networks increase after crosslinking. Thermogravimetric analysis shows that no significant mass loss accompanies the crosslinking reaction. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(butylene terephthalates) modified by hydroquinone bis(2-hydroxyethyl)ether

A series of thermoplastic poly(butylene-co-hydroquinone bis(2-hydroxyethyl)ether terephthalates) (PBHT), with different molar ratios of hydroquinone bis(2-hydroxyethyl)ether (HQEE)/1,4-butanediol 9/91, 18/82 and 27/73, were synthesized via melt polycondensation. The compositions, thermodynamics and crystallization properties of the obtained copolyesters were characterized in detail by ¹H NMR, differential scanning calorimeters (DSC), thermogravimetric analysis (TGA) and X-ray diffraction (XRD). These results showed that the PBHTs were successfully synthesized, and the incorporation of the HQEE group significantly improved thermal properties of the polymers. However, HQEE did not change the crystal structure of PBT. The T_m values of the copolymers decreased (from 208?°C to 174?°C) with increasing content of HQEE segments, on the contrary, T_g values increased (from 37?°C to 43?°C). The temperatures for 5% weight loss did not decrease and appeared at a range of 373–377?°C.     

Fully aromatic poly(ether ketone)s bearing macrocycle pendants: Synthesis and crosslinking

This study reports a method to prepare fully aromatic poly(ether ketone) thermosets. The cyclization of 2′,5′‐dimethoxy[1,1′‐biphenyl]‐2,5‐diol and a difluoro monomer was carried out under pseudo high dilution condition. Two types of fully aromatic poly(ether ketone)s with macrocycle were successfully prepared by copolymerization of macrocycle of aryl ether ketone containing hydroxyphenyl groups, 4,4′‐(hexafluoroisopropylidene)diphenol (HFBPA), and 4,4‐difluorobenzophenone. The obtained copolymers have high molecular mass, good solubility, and high glass transition temperatures in the presence of CsF, the crosslinking reaction of copolymers occurred and afforded fully aromatic thermoset poly(aryl ether ketone)s by ring‐opening reaction driven by entropy. After crosslinking, these copolymers show much higher glass transition temperatures, excellent thermal stability, and better mechanical strength. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7002–7010, 2008     

丁二酸二(二乙二醇单甲醚)酯的制备及其应用

以二乙二醇单甲醚和丁二酸酐为原料,对甲苯磺酸为催化剂,在二甲苯中经开环反应合成了丁二酸二(二乙二醇单甲醚)酯(1),其结构经1H NMR和IR确证。采用恒电流充电法、循环伏安扫描和充放电性能测试了电解质溶液[1.2 mol·L-1双三氟甲基磺酰亚胺锂(LiTFSI)/V(1)∶V(EC)∶V(DEC)=3∶3∶4]在锂离子电池中的电化学性能。结果表明:1与石墨负极有较好的相容性,在0 V~2 V,0.1 C下充放电20次后放电比容量为346.2 mAh·g-1,容量保持率为111.10%。     

含三苯基氧磷结构聚芳醚醚酮酮的合成与表征

以苯酚、对二溴苯及苯基磷酰二氯为原料合成出二(4-苯氧基苯基)苯基氧磷(BPOPPO)。 三氯化铝(AlCl₃)为催化剂,通过缩聚反应,BPOPPO与对苯二甲酰氯(TPC)反应制备出一种含有三苯基氧磷结构的聚醚醚酮酮(P-PEEKK)树脂。 采用傅里叶变换红外光谱仪(FT-IR)、差示扫描量热仪(DSC)、热重分析仪(TGA)和广角X射线衍射(WAXD)等技术手段对P-PEEKK树脂的结构和性能进行表征。 结果表明,P-PEEKK树脂属于非晶聚合物,玻璃化转变温度(T_g)较高,为190.5 ℃;热分解温度(T_5%)为515 ℃,耐热性能较好;极限氧指数(LOI)为42,阻燃性能好,为难燃材料;易溶解于氯仿、1,2-二氯乙烷、N,N-二甲基乙酰胺等有机溶剂中,溶解性能较好,便于涂膜加工;拉伸强度为62 MPa,力学性能较好。     

New light‐colored poly(ether imide)s based on 2,5‐di‐tert‐butylhydroquinone bis(ether anhydride) and aromatic diamines

A series of poly(ether imide)s (PEIs), III _a–k , with light color and good physical properties were prepared from 1,4‐bis(3,4‐dicarboxypheoxy)‐2,5‐di‐tert‐butylbenzene dianhydride ( I ) with various aromatic diamines ( II _a–k ) via a conventional two‐stage procedure that included a ring‐opening polyaddition to yield poly(amic acid)s (PAA), followed by thermal imidization to the PEI. The intermediate PAA had inherent viscosities in the range of 1.00–1.53 dL g^?1. Most of the PEIs showed excellent solubility in chlorinated solvents such as dichloromethane, chloroform, and m‐cresol, but did not easily dissolve in dimethyl sulfoxide and amide‐type polar solvents. The III series had tensile strengths of 96–116 MPa, an elongation at break of 7–8%, and initial moduli of 2.0–2.5 GPa. The glass‐transition temperatures (T_g) and softening temperatures (T_s's) of the III series were recorded between 232 and 285 °C and 216–279 °C, respectively. The decomposition temperatures for 10% weight loss all occurred above 511 °C in nitrogen and 487 °C in air. The III series showed low dielectric constants (2.71–3.54 at 1 MHz), low moisture absorption (0.18–0.66 wt %), and was light‐colored with a cutoff wavelength below 380 nm and a low yellow index (b^*) values of 7.3–14.8. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1270–1284, 2005     

Synthesis and properties of poly(ether imide)s based on the bis(ether anhydride)s from hydroquinone and its derivatives

Four bis(ether anhydride)s, 4,4′‐(1,4‐phenylenedioxy)diphthalic anhydride (IV), 4,4′‐(2,5‐tolylenedioxy)‐diphthalic anhydride (Me‐IV), 4,4′‐(2‐chloro‐1,4‐phenylenedioxy)diphthalic anhydride (Cl‐IV), and 4,4′‐(2,5‐biphenylenedioxy)diphthalic anhydride (Ph‐IV), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4‐nitrophthalonitrile with the potassium phenoxides of hydroquinone and various substituted hydroquinones such as methylhydroquinone, chlorohydroquinone, and phenylhydroquinone in N,N‐dimethylformamide, followed by alkaline hydrolysis and dehydration. Four series of poly(ether imide)s were prepared from bis(ether anhydride)s with various aromatic diamines by a classical two‐step procedure. The inherent viscosities of the intermediate poly(amic acid)s were in the range of 0.40–2.63 dL/g. Except for those derived from p‐phenylenediamine and benzidine, almost all the poly(amic acid)s could be solution‐cast and thermally converted into transparent, flexible, and tough polyimide films. Introduction of the chloro or phenyl substituent leads to a decreased crystallinity and an increased solubility of the polymers. The glass transition temperatures (T_g) of these polyimides were recorded in the range of 204–263°C. In general, the methyl‐ and chloro‐substituted polyimides exhibited relatively higher T_gs, whereas the phenyl‐substituted ones exhibited slightly lower T_gs compared to the corresponding nonsubstituted ones. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 665–675, 1999     

Magic angle carbon-13 NMR study of solid poly(ethylene naphthalene-2,6-dicarboxylate)

Amorphous (1) and semicrystalline (2) samples of poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) have been investigated by cross-polarization/magic angle spinning (CP/MAS) ¹³C NMR at 26°C (1 and 2), 100°C (1) and 120°C (2) in order to study the phase structure and the local motion of polymer chain segments at temperatures below and close to T_g (120°C). The lineshape of the ethylene unit ¹³C signal in sample 2 is consistent with the presence of two components which were assigned to trans and gauche conformations. The first component arises mainly from the crystalline regions and the second one from the amorphous part. Cross-polarization curves were traced by changing the contact time between carbon and proton reservoirs. T_CH (cross relaxation time) and proton T_1p (spin-lattice relaxation time in the rotating frame) values were obtained as best fit parameters by fitting calculated curves to the experimental data. All ¹³C NMR data are consistent with the presence of highly rigid ethylene units in both semicrystalline and amorphous samples within the temperature range (T) investigated. This result is in disagreement with the ¹H NMR wide line spectra which showed a noticeable narrowing of the linewidth with increasing temperature in the same range, hence indicating a great mobility of the chain segments. To account for this discrepancy a qualitative model based on the existence of two distinct dynamic regions, one where motion is highly restricted and the other one where large reorientations of ethylene group torsional angles take place, is suggested. The NMR results led to the conclusion that three structural phases are present in PEN: crystalline, very rigid amorphous, and very mobile amorphous. © 1995 John Wiley & Sons, Inc.     

环糊精和α-萘乙酸包络物的核磁共振研究

利用溶液2D-ROESY谱,利用溶液2D-ROESY谱, 13C固体高分辨谱以及自扩散系数测量等核磁共振技术, 研究了环糊精(CD)和α-萘乙酸(α-NAA)的相互作用. 结果表明, α-CD和β-CD均能与α-NAA形成包络物, 但是由于尺寸更为匹配, β-CD与α-NAA体系的包络相互作用强度明显比α-CD和α-NAA体系的大; 通过测量 β-CD与α-NAA混合溶液中α-NAA的自扩散系数, 计算出包络物结合与解离的平衡常数, 以此为基础对β-CD/α-NAA 体系在实现α-NAA缓释方面的应用方式进行了探讨. 13C固体高分辨谱以及自扩散系数测量等核磁共振技术, 研究了环糊精(CD)和α-萘乙酸(α-NAA)的相互作用. 结果表明, α-CD和β-CD均能与α-NAA形成包络物, 但是由于尺寸更为匹配, β-CD与α-NAA体系的包络相互作用强度明显比α-CD和α-NAA体系的大; 通过测量 β-CD与α-NAA混合溶液中α-NAA的自扩散系数, 计算出包络物结合与解离的平衡常数, 以此为基础对β-CD/α-NAA 体系在实现α-NAA缓释方面的应用方式进行了探讨.     

含联苯结构聚醚醚酮酮共聚物和共混物的制备及性能研究

聚醚醚酮（PEEK）是八十年代初投入市场的全芳香结构热塑性耐高温特种工程塑料，它的7’。一143“C，Tm一334C“‘，最大结晶度为48％，典型制品结晶度为20％～30％［”．PEEK可用通常的设备成型，其制件、纤维、涂料及复合材料在电子电器、机械设备、交通运输、宇航、原子能工程、军事等领域有广泛的用途［’j．聚醚醚酮酮（PEEKK）是继PEEK之后，由德国Hoechst公司开发出来的又一种全芳香结构热塑性耐高温特种工程塑料［‘j．为了研究该类聚合物的结构和性能的关系，我们在实验室中合成了PEEKK和含联苯结构聚醚醚酮酮（PE－＊…     

A novel synthesis of reactive polymers with pendant halomethyl groups by the polyaddition reaction of bis(epoxide)s with bis(chloroacetoxy)esters or bis(bromoacetoxy)esters

New reactive polymers with pendant halomethyl groups were successfully synthesized by polyaddition reactions of bis(epoxide)s with bis(chloroacetoxy)ester such as 1,4-bis [(chloroacetoxy)methyl]benzene (BCAMB) or 1,4-bis[(bromoacetoxy)methyl]benzene (BBAMB) using quaternary onium salts or crown ether complexes as catalysts. The polyaddition reaction of diglycidyl ether of bisphenol A (DGEBA) with BCAMB proceeded very smoothly with high yields (83–96%) by the addition of quaternary onium salts such as tetrabutylphosphonium bromide (TBPB) or crown ether complexes such as 18-crown-6/KBr as catalysts to produce high molecular weight polymers, although the reaction occurred without any catalyst to give low molecular weight polymer in low yield at 90°C for 48 h. It was also found that the reaction proceeded smoothly in aprotic polar solvents such as N-methyl-2-pyrrolidone (NMP) and N,N-dimethylacetamide (DMAc) to produce high molecular weight polymers. Polyaddition reactions of DGEBA or digylcidyl ether of ethylene glycol (DGEEG) with BBAMB, other bis(chloroacetoxy)esters or bis(bromoacetoxy)esters using TBPB in DMAc also proceeded smoothly to give the corresponding polymers. The resulting poly(ether-ester)s contain reactive halomethyl groups as side chains, which were introduced during main chain formation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3791–3799, 1997     

A SOLID NMR STUDY OF POLYETHERESTER-UREAS

The morphology of some polyetherester-ureas were studied by ~(13)C CP/MAS and ~1H wide-line NMR spectroscopy. It was found that the HDI and MDI based polymers have well crystallized hard segments, whereas the TDI and HMDI based ones have not. For HDI/MDI based polymers, the presented results suggest that the distribution of two kinds of hard segment units is mainly in a block form. The influences of the different hard segment and chain length on the mobility of the soft segment were also studied.     

Tetrakis(hydroxymethyl)phosphonium salts: Their properties,hazards and toxicities

Abstract

Tetrakis(hydroxymethyl)phosphonium chloride (THPC) and sulfate (THPS) are of importance in the textile industry as flame retardants, in the oil industry as scale-removers, as biocides for water systems, in the leather industry as tanning agents, in nanochemistry as reductants and stabilizers of nanoparticles, and as oxygen-scavengers in medical uses. In the majority of cases, THPC and THPS themselves are not chemically active and solely play a role of reservoirs for the more reactive species tris(hydroxymethyl)phosphine (THP) and/or formaldehyde. The contents of THPC/THPS solutions greatly depend on pH, which is now recognized as a key factor, for example, in metal hydrosol preparations, biocidal activity, and ecotoxicity. This review is intended to reveal and explain the complex behavior of THP and (HOCH₂)₄P⁺ salts in aqueous solutions, conditions that might lead to potential hazardous compounds such as formaldehyde, hydrogen gas, phosphine PH₃, and bis(chloromethyl)ether. Literature data on their toxicities are reviewed.     

New Potassium- and Cesium-selective Ionophoric Bis(crown ether)s Derived from Xanthene-4,5-dicarboxylic Acid

A series of bis(crown ether)sbased-upon a xanthene-4,5-dicarboxylic acid skeletonwas prepared and their ionophoric properties towardalkali metal cations were investigated. Bis(crownether)s bearing 15-crown-5 and 18-crown-6 moietiesexhibited pronounced extraction efficiencies towardK⁺ and Cs⁺ ions, respectively, and theextraction constant estimated by solvent extractionstudies was as high as 10⁹ for the 2-K⁺ and 3-Cs⁺ systems. Using UVtitration of potassium picrate with 2 in THF, thecomplex was found to have a structure of a completelyencapsulated guest in the host. In transportexperiments, the bis(crown ether)s showed nosignificant selectivity pattern compared withextraction results, again implying the strongcomplexation of bis(crown ether)s. Ion-selectiveelectrode studies also demonstrated that the selectiveionophoric properties of 2 toward K⁺ werereminiscent of the natural antibiotic valinomycinexcept for a somewhat slow response.     

Strukturen und intramolekulare Bewegungen spezieller polycyclischer Germanium(II)-amide

Structures and Intramolecular Motions of Special Polycyclic Germanium(II) Amides Compounds of the general formula MeSi(NtBu)₃Ge₂X (X = Cl ( 1 ), N(SiMe₃)₂ ( 2 ), P(C₆H₅)₂ ( 3 )) have been synthesized and characterized by X-ray structure analyses and multinuclear NMR-spectroscopy. The temperature dependent NMR investigations of 2 in solution show bond fluctuations concerning the metal-nitrogen bonds and ElMe₃ (El = C, Si) rotations. Some of these intramolecular motions also occur in the solid state as detected by means of temperature dependent ¹³C CP/MAS NMR spectroscopy. The special nature of these NMR spectroscopically detected movements in solution are compared with the results of the X-ray structure analyses. A model of the dynamical behaviour of 2 in solution suggests a quasi circular movement of the two germanium atoms within the molecular cage. After the phase transition from solution to the solid state at ambient temperature this special metal fluctuation is stopped. In the solid state the rotations of the SiMe₃ groups in 2 are only hindered at low temperatures.